Search Documents

By C. P. Fiske

THE pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers; and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance? come the condensers, as large numbers are used in the manufacture of spelter, and improvements m quality result in material decreases in working cost. , While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they-are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are concerned. Materials Bond Clay.-The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather -it in the, accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss. of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later), accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is, evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons-with the clay as usually handled.

Jan 10, 1917

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

This brief resume of events, transpiring in Mexico, culled from the daily New York newspapers, since the last Bulletin went to press, does not indicate any degree of improvement in the situation. MEXICAN MINISTER TO FRANCE RECOGNIZED A dispatch from Paris quotes Alberto J. Pani, Mexican Minister to France, as saying lie lead received notification that lie might present his credentials at the French Foreign Office on May 13. This notice came at the moment the Mexican press was announcing his departure for Spain because of inability to present his credentials. MORE REVOLUTIONARY TROUBLES SOUTH AND NORTH Revolutionary outbreaks hulked large in advices from Mexico City at the end of May, says the New York Tribune. General Eznesto Danny, a major, four other officers and forty men, composing a train guard on the Isthmus of Tehuantepec Railroad, were killed recently in an attack by rebels under Felix Diaz&apos;s command. The troubles in the south, coupled with the fact that Villa&apos;s activities in the north have necessitated sending troops to campaign against him, have reacted in the capital seriously, it is reported. Military guards hi Mexico City have been doubled and machine guns have been placed on the roofs of the National Palace and the Cathedral. STRIKE AND MARTIAL LAW IN MEXICO CITY Advices from Mexico City, according to the Evening Sun, said that virtually every school teacher in the city was out on strike and that recurrent rioting was being put clown by armed trucks manned by Federal soldiers. The strike of the school teachers was clue to the fact that they had not been paid for months, but the direct incitement is said to have been the contrast between their impoverished position and that of Carranza&apos;s generals, who are described as rolling in wealth, and who flaunted their opulence on the streets of Mexico, riding about in high powered automobiles with women bedecked with diamonds and other jewelry. The city is said to be virtually under martial law with no immediate prospect. of a subsidence of the bitter feeling against the military caste.

Jan 7, 1919

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don&apos;t assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it&apos;s straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it&apos;s very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By S. J. Hruska, G. M. Pound

The critical supersaturations for appreciable nucleation rate of cadmium crystals on copper and glass substrates at 186°Kwere measured as a junction of thermal-beam energy over a range of source temperatures between 616" and 839OK. There was no effect of source temperature on critical super saturation. This implies that the adsmbate prior to nucleation is in thermal equilibrium with the substrate. THE deposition of metallic vapors on solid substrates has been found to exhibit a critical behavior in that the rate of formation of deposit increases markedly when the intensity of the vapor source is increased slightly.* Evidence of the ability of sub- where Je is the flux which would arrive if the substrate were equilibrated with bulk condensate at the adsorbate temperature. The following work was undertaken to test this hypothesis. A) Energy Exchange Between Metallic Vapor and Substrates. When a freely translating atom collides with a stationary solid body its energy and momentum undergo changes which determine whether the atom is reflected or adsorbed. An atom is considered to be reflected if it returns to a freely translating state after remaining under the influence of the body for only a time comparable to the period of oscillation of atoms on the surface. An atom which remains for a longer time is said to be in an adsorbed state. The parameter which describes the energy transfer occurring at the interface is the thermal-accommodation coefficient which may be defined in terms of energy as Ei = average energy of impingent atoms, Eeq = average energy of an emergent atom which has equilibrated with the substrate, and Eem = average energy of an emergent atom. If a temperature is assigned to each of these energies, we have at as defined by Knudsen.2 Since this allows no distinction between reflected and evaporated atoms, a more specific definition is introduced for the present purposes, namely 71 = probability that an impingent atom is transferred to an adsorbed state, aj = thermal-accommodation coefficient for reflected atoms, and aTc = thermal-accommodation coefficient for adsorbed atoms. During a time t,, the mean stay time, prior to evaporation the adsorbed atom (adatom) will interact with the substrate and this will have the net effect of transferring the adatom towards a state of

Jan 1, 1964

By J. N. Butler, R. J. Morris

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:1 are possible on head assays of 0.10 to 0.50 pct U 3 O 8. Additions of certain base metal salts aid in recovery and materially increase the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals. RAPID increase in mining and milling uranium ores during the past seven years and the discovery of large tonnages of uranium-bearing material too low in grade to stand the cost of leaching have developed considerable interest in possible methods for beneficiating these marginal ores. Such ores are generally classed as those containing less than 0.10 pct U3O8. Development of a beneficiation method that would give both high recovery and high ratio of concentration would also make possible the beneficiation of higher grade ores and would provide higher grades of feed to existing leaching plants. Although considerable research and testing on physical or physico-chemical beneficiation of domestic uranium ores has been done in the past, to the best knowledge of the authors only a single application of physical beneficiation is now in operation on a commercial scale. Flotation has been attempted on the basis of mineral association rather than by direct concentration of the contained uranium minerals. Flotation studies conducted on this project on certain ores gave recoveries of 60 to 70 pct of the uranium by the use of conventional flotation agents such as oleic acid, but ratios of concentration were in the order of 1.5:1 to 2.5:1. Subsequent cleaning to upgrade the concentrates rapidly increased losses in the cleaner tailings, which were not later refloated in the rougher flotation. Selection of Collector: In selecting desirable organic collectors for these oxide systems, a thorough study was made of the relationship between structural characteristics and collector activity by an examination of the behavior of a number of different functional arrangements present in a variety of organic molecules, (see Fig. 1). It is generally accepted that a collector must have a relatively long-chain hydrocarbon radical and a chemically reactive elec-trophilic center. Such a requirement could be met by a large number of compounds, but steric effects at the uranium mineral surface, solubility, compat-ability with aqueous systems, air avidity, bond strength at the mineral surface, interfacial concentration of the collector, and diffusion rate of the formed complex from the air-water interface eliminated many as unsuitable for this purpose. Preliminary investigations were completed of possible collector designs consisting of aliphatic and aromatic hydrocarbon radicals attached to stable combinations of nitrogen, oxygen, sulfur, and halogen electrophilic centers, Fig. 1.Tests were made to determine melting point spans, solubility of mineral-collector combinations in various solvents, reactions with soluble uranium salts, contact angles, and floatability by semi-quantitative beaker methods.&apos; Contact angle determinations were not too useful because of the fine particle sizes of available mineral samples. From the foregoing study it appeared that nitrogen-sulfur electrophilic centers coupled with straight-chain saturated alkyl hydrocarbon radicals would hold the most promise for floating secondary uranium minerals. As the dithiocarbamate compounds can be made to combine these attributes they were selected for further study. The dithiocarbamates form a parallel structure to the xanthates, with the fortuitous exchange of

Jan 1, 1957

By J. W. Furness

THE utilization and collection of waste materials have gone on for centuries, and have become a habit of the human race. The degree to which the salvaging of waste plays a part in a nation&apos;s industry depends largely on the availability of raw materials within the political confines of the country itself, or its ability to purchase such material from outside. When purchase is necessary careful economical use of the raw materials results. These economies, as a rule, are represented by lengthening the life of the given article as well as much re-use. For many years the steel industry of Italy and Japan has depended largely on importations of scrap, yet both are important. As long as the expenses incident to the conditioning and marketing of materials manufactured from salvaged waste are less than the cost of virgin material, the salvaged material will be re-fabricated and in many cases will compete with primary materials. One of the most obvious methods for furthering the efficient utilization of our limited mineral resources is the salvaging of mineral wastes. This method, moreover, in¬creases the available supply of a given material. If the price depends on a balance of supply and demand and the recovery from wastes enlarges. the supply, there can be no question but that it influences the sales price of primary.

Jan 1, 1931

By Howland Bancroft

AMERICAN investment in foreign mining interests today faces its greatest task. U. S. dollars must make possible the. steady procurement of the minerals our defense effort consumes in huge quantities. The two most vital factors involved in foreign procurement are time and the continued good will of the nations from which minerals are purchased. The Point IV program was formulated to care for the second item, but it has failed to do the job. Its lack of success has not been from intent or from basic failure in formula. Foreign Investment, Four Eras Foreign mineral development, in so far as participation by private capital from the United States is concerned, may be divided into four main chronological categories: First: The period prior to the first World War when people, capital and products moved with relative freedom across international boundaries, and London was the recognized mining seat of the world. By the end of 1919 the United States direct investments abroad amounted to $3.9 billion of which some $900 million were in mining and smelting and $600 million in petroleum. Investment climate throughout most of the world was excellent. Second: The period between the end of World War I, when the international economy had been shaken from its foundations, and the beginning of the great depression of the 1930&apos;s, which still further disrupted the world economy. By that time the world mining center had moved across the sea and the United States direct investments abroad had increased to $7.7 billion of which mining and smelting accounted for $1.2 billion and petroleum for $1.1 billion. Investment climate was good in most parts of the world. Third: The period of the depression of the 1930&apos;s and the beginning of World War II during which foreign trade was still further disorganized and the international economy collapsed. Nazi barter agreements were initiated in many parts of the world, and Soviet propaganda commenced to make its, influence felt in many countries. During this period United States direct investments abroad decreased to $7.3 billion. Mining and smelting investments during the same period decreased some $200 million, though direct investments in foreign petroleum areas increased an equal amount. Investment climate became less and less hospitable in all parts of the world affected by economic nationalism. Fourth: The period since the beginning of World War II during which total direct investments abroad increased from $7.3 to $13.7 billion. Of this sum, at the beginning of 1950 investment in foreign mining and smelting is reported to have been $1.2 billion-back to where it was in 1929, and in petroleum to have reached $3.7 billion. Investment climate remained favorable in the countries respecting contractual obligations and fair in their treatment of invested capital. [ ] As noted above, the relative freedom of passage across international boundaries by people, capital and products ended with World War I and the situation remains unchanged in a greater part of the world. While this same war upset international economy, the depression of the 1930&apos;s caused the collapse of world trade, and exports from all countries fell to an alarmingly low figure. Some countries almost ceased to export. Chile, for example, reported a drop of 88 pct in exports. Countries with

Jan 1, 1952

By C. P. Fiske

The pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers, and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance come the condensers, as large numbers are used in the manufacture of spelter, and improvements in quality result in material decreases in working cost. While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are conccrned. Materials Bond Clay.—The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather it in the accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later) accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons with the clay as usually handled.

Jan 1, 1918

By M. L. Holzworth, Philip R. Sperry, Paul A. Beck

INTRODUCTION THE basic work of Z. Jeffries1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria have been added, Jeffries found that grain growth was inhabited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. Such a "coarsening temperature" was later found by Gross mann13,14 in certain types of steel, while Bain showed" that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work16,17,18,19,21 demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently.20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases, with the titanium content. That coarsening may occur, as a result of certain heat treatments, even in low carbon rimmed sheet steel, was shown by Samuels,22 He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material, In this instance the identity of the inhibiting phase has not been determined, However, Tangerding found 23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction, The carbide particles can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air, is followed by annealing in hydrogen for 75 hr at the same temperature, grain growth is more spectacular; usually the whole specimen is transformed into a single crystal (approx. 1,5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth resulting from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced during the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pct Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1948

By Carl Altstetter, Roy Adams

Measurements of enthalpy changes and transformation temperatures me reported for the fcc -hcp marten-sitic transformation in pure cobalt single and multi-variant crystals andpolycrystalline specimens. From these measurements the free-energy difference between the two phases was calculated for both heating and cooling and for repeated cycles through the transformation. For heating of single crystals the average value of enthalpy change was 113 cal per mole but on cooling it was 84 cal per mole. This difference is interpreted in terms of lattice imperfections which are introduced during transformation. A calorimeter suitable for measurement of enthalpy changes of athertnal transformations is described. COBALT exhibits an allotropic phase transformation at around 417°C&apos; where an hcp phase (a = 2.507, c = 4.0686, c/a = 1.6228)~ stable at low temperatures transforms to an fcc phase stable up to 1495°C. The transformation has a hysteresis of about 30°C— the exact magnitude of the hysteresis depending on the number of transformation cycles, grain size, impurity content, and prior treatment.&apos;-6 The athermal character of the transformation and surface relief due to transformation shear indicate that the transformation is martensitic. Pole mechanisms for the transformation have been discussed by Sebilleau and Bibrin, Bilby, Seeger,&apos; and Basinski and Christian. These authors have proposed that the cooling transformation is effected by rotation of a Shockley partial dislocation around a pole dislocation with a screw component of 2a/3(111). Such a rotation would change the stacking of close-packed planes from the abcabc fcc stacking to the ababab hcp stacking sequence. This mechanism would predict a lattice correspondence of {111}fcc~~(0002~cp, have been observed. One would expect the heating transformation to occur similarly, involving dislocation movements on the (0002)hcp. However, a high density of pole dislocations and high dislocation ve- locity are required to account for microscopic observations. Furthermore, the high back stress developed on the Shockley partial dislocation as it rotates toward the sessile dislocation associated with it makes it doubtful that this is in fact the transformation mechanism. A mechanism for spontaneous nucleation of partial dislocations1*l2 seems more reasonable. If a single crystal of cobalt is cycled through the transformation but never heated above 600°C, it will remain single."13 However, if the specimen is heated through the transformation and held for a short time at or above 1000°C before cooling, the cooling transformation usually involves all four {lll}fcc habits, resulting in neighboring orientations of hcp differing by 70.5 deg. This condition is termed multivariance and has been observed by Bibring and sebilleau5 and Nelson and ~ltstetter.&apos; The latter authors used single crystals of cobalt grown in an electron beam zone refiner. They proposed that the strongly directional cooling caused the initial cooling transformation to occur on the {lll)fcc most nearly perpendicular to the temperature gradient. Transformation shear on one set of {lll}fcc planes immobilized dislocations on the other {lll}fcc planes involved in the initial transformation. Since there is only one (0002)hcp plane orientation, the product of subsequent heating transformations could have no more than two variants—the original fcc orientation or its twin. If, however, the specimen was annealed at a high temperature, such as 1000°C, there would be relaxation of dislocations into low-energy configurations, and in the absence of a sharp temperature gradient transformation on all four (111 Ifcc planes could occur. If a dislocation mechanism is responsible for the transformation, the perfection of the lattice should affect the reversibility of the transformation. Mutual constraints of neighboring grains in polycrystalline material would inhibit dislocation movement resulting in increasingly sluggish transformation. Indeed, Nelson and Altstetter found the M, to decrease and the A, to increase in going from single crystals to multi-variant specimens to polycrystals. The effect is enhanced by decreasing the grain size of a solid specimen or a powder.6&apos;14 Data on the free-energy difference necessary to initiate the transformation gives information about the driving force of the transformation. This is an important consideration in the understanding of the transformation mechanism. The free-energy change associated with the transformation of the hcp phase to the fcc phase at some temperature T different from the equi-

Jan 1, 1969

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.&apos; It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

L. C. Graton, Cambridge, Mass.—The subject of chalcocite occur; rence and its geological significance has, of course, a very important commercial bearing, as shown by the recent remark of a hard-headed mining .man: "This secondary enrichment business is one thing you geologists have put up which we can hang on to, and come out right." Most enrichments of copper ores depend upon the formation Of chalcocite from leaner sulphides. Recently it has been shown that not only does there exist this secondary or derived chalcocite, * but that in certain ores the mineral is present as an initial or original constituent, which therefore we may call primary. The desirability of distinguishing between these two kinds of chalcocite is evident and has recently been emphasized. That constitutes the first problem in this connection. I believe many who are working upon secondary enrichment of mineral deposits are giving much attention to that particular question. It is now possible to distinguish primary from secondary chalcocite in many cases. In such cases, what do we know of the&apos; conditions under which this secondary or derived chalcocite was formed? , This is the second main question in connection with the subject. It is now plain, at least in many instances, that the formation of this derived chalcocite represents a phase of oxidation if we have in mind the primary ore as the thing acted upon. The next important question—and it is most important—is: does such oxidation go on above the zone where the rocks are saturated with water—that is, above the water level—or below, or indiscriminately above and below? Many of you have, or have had, opportunities to study at first hand, day after day, occurrences that&apos; enable valuable conclusions to be drawn upon these and other important questions concerning the formation and significance of chalcocite. It is greatly to be hoped that your testimony will be made available and undoubtedly it will go far toward clearing up some of these doubtful points. John D. Irving, New Haven, Conn.—A short time before this meeting was called, H. V. Winchell, who was unable to be present, requested me to exhibit and describe these two samples of pyrite. (Exhibiting specimens.) They consist of fragments of pyrite inclosed in two small bottles. The first bottle shows fragments of pyrite which were immersed in water carrying copper sulphate but without SO2 for a period of two years. They remained comparatively clear and bright. No chalcocite has been deposited on them. The second bottle shows fragments of

Jan 1, 1915

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible lighting while persons are working in such places. Section 317(e) further provides that such working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31, 1970, a notice of proposed rulemaking which prescribed the illumination to be provided in the working places of underground coal mines. In light of written comments, suggestions, and objections to this proposed rulemaking, the proposed standards were withdrawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974, and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting-standards &k place on October 1, 1976, which means that the underground coal mining, industry must comply with face illumination requirements by April 1, 1978.

Jan 3, 1978

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor&apos;s analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

By E. D. Slone, F. L. Dillard

When a new mine is in the planning stages, one of the most important decisions to be made is the selection of&apos; face haulage equipment and the interrelated transportation system to the surface. Equally important is the method of transporting personnel supplies and repair parts from the surface to the working places. When Bell & Zoller management elected to open the new Zeigler mine in the No. 9 seam near Madisonville, Ky., last year, various transportation systems were considered. It was agreed early that a slope mine would be preferred to a shaft mine, and that belt conveyors would be more economical than a rail system.

Jan 1, 1970

MARCEL R. DALY (written discussion+).-I have read with great interest Mr. W . Van Der Gracht&apos;s discussion of my paper and I fail to see where his theory contradicts mine on any fundamental point. My contention is that petroliferous accumulations are generally coincident with diastrophic deformations, synchronous with them and essentially a result of them. This implies that the causes which have led to the distortion of the strata, whatever these causes may be (thrusts, torsion, etc.), have also led to the concentration and accumulation of the hydrocarbons existing in the strata at that time. It is in this respect that both set of phenomena may be said to be related in space and in time and that we may speak of an identity of causes. It is evident that no concentration of the hydrocarbons could take place where these hydrocarbons would not exist. But whenever they do so exist, deformation will tend to concentrate them; and whenever they are found to be concentrated (or accumulated) the cause of their accumulation will have to be traced directly to distortion. I have tried to show, in some previous papers,&apos; the probable sequence of such a mechanical process in the simple case of a series of parallel, superposed, horizontal and homogeneous layers, individually uniform in thickness, but variable in composition and resistance; and I have pointed out that the general results so obtained would harmonize with some striking features recognized in the field. But I have also stated that conditions being much more complicated in nature than in the theoretical instance considered above, a complex superposition of effects would. have to be expected as a general rule, though the leading principle would remain the same. Mr. Van der Gracht admits that the motion of the primary oil, when it has been formed, and its accumulation in adequately porous containers, if any, that would be mostly found on the front edge of the original geosynclines, would be due to the action of the mountain-building forces. Our agreement on this point seems to be complete. But Mr. Van der Gracht wants also the formation of the bituminous matter in its primary form to be coincident only with the earliest phase of the uplift, viz., after the slow geanticlinal upheaval has been completed, and the accumulation

Jan 3, 1918

By Roshan B. Bhappu, Ronald J. Roman, Dexter H. Reynolds

The reaction between manganese dioxide and molybdenite in a water- sulfuric acid medium was studied at atmospheric pressure and from 25° to 103°C. Both solids are dissolved to give, as final products in solution, Mo(VI), S(VI), and Mn(II). Stoichiornetric relationshifis are most simply represented by the equation MoSz + YMnO2 + 15H+ - HMoO-4 + 2HSO-4 + 9Mn++ + 6H20 The rate of this reaction was found to be dependent on temperature, manganese sulfate concentration, acid concentration, and, in a complex way, the surface areas of both manganese dioxide and molybdenite. Both the total amount of manganese dioxide and tnolybdenite and the ratio of manganese dioxide to molybdenite played a part in determining the over-all rate of the reaction. The effect of acid concentration on the rate was also dependent on the ratio of manganese dioxide to molybdenite. SEVERAL reports in the literature describe reactions using manganese dioxide in water-sulfuric acid media as an oxidizing agent. Nearly all previous work describes interactions between an ion and manganese dioxide, such as the oxidation of ferrous to ferric iron,&apos; or the interaction between a molecule in solution and manganese dioxide, such as the oxidation of toluene to benzaldehyde.2 Only a few references describe the use of solid manganese dioxide to oxidize another solid in sulfuric acid. One report3 states, "Manganese dioxide in dilute sulfuric acid solutions had no beneficial effect (in leaching copper from chalcopyrite), but in more concentrated acid solutions the rate of solution was about the same as that for permanganate." In 1902 a German patent4 described a process which used manganese dioxide in strong (50°Be&apos;) sulfuric acid for oxidizing chromite ores to soluble iron and chromium salts. The process consisted of mixing the sulfuric acid with the finely ground ore and manganese dioxide. The pulp was then heated to about 120°C and an electric current passed through it. The manganese dioxide apparently dissolved in the strong, hot acid solution, oxidized the iron and chromium and itself was reduced to manganese 11! then was oxidized at the anode back to manganese dioxide, and the cycle repeated. An extensive study5 of the kinetics of the oxidation of pyrite with manganese dioxide indicated that in dilute sulfuric acid solutions (about 0.1 N) and at elevated pressures the dissolution of the pyrite was brought about by air oxidation of the iron to ferrous sulfate, followed by manganese dioxide oxidation of the ferrous sulfate to ferric sulfate. The mechanism proposed by the authors involved the oxidation of the iron at the surface of the manganese dioxide. Also! the oxidation of sulfide sulfur to sulfate was credited to the oxygen in the air, not to the manganese dioxide. Since the metallurgical literature is lacking in information concerning the use of one solid to oxidize another solid. the current investigation was under-

Jan 1, 1965

I. MCLAUGHLIN, R. P.-Protecting California Oil Fields from Damage by Infiltrating Water. Discussed by M. E. Lombardi, A. F. L. Bell, A. C. McLaughlin, R. P. McLaughlin, William A. Williams, Mark L. Requa, C. D. Keen 2413 BEST, W. N.-Petroleum as Fuel Under Boilers and in Furnaces. Discussed by William A. Williams, Hennen Jennings, David T. Day, Mark L. Requa, A. F. L. Bell, W. N. Best 2420 JOHNSON, ROSWELL H.-Sliding Royalties for Oil and Gas Wells. Discussed by William A. Williams, A. C. McLaughlin, A. F. L. Bell, Roswell H. Johnson 2423 BELL, ARTHUR F. L.-Important Topping Plants of California. Discussed by William A. Williams, David T. Day, A. F. L. Bell 2426 LOMBARDI, M. E.-The Cost of Maintaining Production in California Oil Fields. Discussed by C. D. Keen, Mark L. Requa, H. M. Bacon, M. E. Lombardi 2427 HUNTLEY, L. G.-Oil, Gas, and Water Contents of Dakota Sand in Canada and United States, Discussed by E. W. Shaw 2428

Jan 12, 1915

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,&apos; shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951