Search Documents

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By AIME AIME

THE meeting of the Petroleum Division at Houston, Oct. 10-12-headquarters, Rice Hotel-was preeminently a technological success. Two hundred and twenty-five attended the Thursday morning session and approximately 200 attended the sessions on Thursday and Friday afternoons and Saturday morning. Harry Power, Chairman of the Division, in his opening remarks, credited Paul Weaver and M. Albertson, respectively chairman and vice-chairman of the local committee, with working long and prodigiously in organizing the program. The theme of the initial session was indicated by Mr. Albertson in a statement relative to the estimation of developed petroleum reserves. He said that the problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became an acute one. Mr. Albertson gave some of the more important reasons for this situation. Since the decline-curve method became inapplicable, the volumetric method has become the chief one used. It depends on the factors of productive formation volume, porosity, saturation, and recovery. He briefly discussed the factors necessary for application of the volumetric method. P. P. Gregory discussed the estimation of petroleum reserves in prorated lime¬stone fields (see his paper in the October

Jan 1, 1935

By Rodolfo V. de la Cruz

The accurate assessment of the in situ deformability of rock masses is very important in the de and construction of underground openings for mining and geotechnical engineering applications. This paper presents a method and device for determining the in situ deformability of rock masses by relating the borehole jack load to the diametral displacements at a number of orientations around the borehole wall. The method called mu1tiple measurement method include the steps in which: a) diametral displacement sensors are installed at different orientations around the borehole to measure the changes in length of various diameters of the borehole; b) a uniaxial load is applied on two opposed octants of the borehole wall, and; c) using elastic theory and assuming a reasonable value for the Poisson's Ratio of the rock mass, the in situ deformability of the surrounding rock materials is determined from the measured diametral displacements and applied unidirectional load. The multiple measurement method has a significant advantage over existing methods since it provides several independent data in a single test from which to calculate the in situ deformability of the rock mass. The multiple data provide a check and counter check on the reliability and accuracy of the various measurements. The multiple data would also provide a means of quantifying the degree of fissuring on the borehole wall. Information on the degree of fissuring is very important in numerical modeling of rock masses.

Jan 1, 1984

By N. A. Hasenack

A full description of tests and test results of potgrate--as well as industrial tests is given. It is concluded that the favorable effects of magnetite ores on the pelletizing-plant results can almost be obtained by replacing the magnetites by hematites with coke breeze. The amount of coke breeze to be added should be about 30% above the theoretical value which is derived from the transition heat of the magnetite. The total amount of coke breeze should be limited to 1.5%.

Jan 1, 1977

By N. C. J. Ros

The paper deals with pressure gradients occurring in flowing and gas-lift wells, a knowledge of which can be applied to the determination of optimum flow-string dimensions and to the design of gas-lift installations. The study is based on a pressure-balance equation for the pressure gradient. It appears that a pressure-gradient correlation of general validity must essentially consist of two parts-—one part being a correlation for liquid hold-up and the other part being one for wall friction. Dimensional analysis indicates that both liquid hold-up and wall friction are related to nine dimensionless groups. It is shown that in the field of interest only four groups are really important. On the basis of these four groups a restricted experimental program could be selected that nevertheless covered practically all conditions encountered in oil wells. This experimental program has been carried out in a laboratory installation. Three essentially different flow regimes were found. The pressure gradients in these regious are presented in the form of a set of correlations. Comparison of these correlations with a few available oilfield data showed excellent agreement. INTRODUCTION Prediction of the pressure drop in the flow string of a well is a widely known problem in oilfield practice. Accurate data on the pressure gradient of a simultaneous flow of gas and liquid in a vertical pipe are especially useful for the determination of optimum flow-string dimensions. It is well known that with moderate gas and liquid flows such a vertical string acts as a "negative restriction". The pressure drop decreases (1) when the throughput through a given pipe increases, and (2) when at a given throughput the cross-sectional area is decreased. The reason is that, with increasing velocities, the flow becomes more agitated so that the gas slips relatively more slowly through the liquid. With the resulting increase in gas content in the string, the static head decreases. When the area becomes very small, however, the high velocities entail great wall friction, which causes an increase in pressure drop. For a given flow, therefore, minimal pressure drop is obtained by using a certain cross section. This means that, in principle, each well can be provided with an optimum flow string for minimum pressure drop and, hence, maximum possible production rate. The procedure for the selection of the optimum string has been discussed by Gilbert.' A necessary tool in the procedure, however, is accurate knowledge of the pressure gradient to be expected for various values of the governing variables. Another application of pressure-gradient data lies in the field of gas-lift practice: they provide a means of determining the optimum gas-injection rate, optimum injection pressure and optimum injection depth. Much work has already been done in the study of the pressure gradient of vertical gas-liquid flow. Poett-mann and Carpenter2 presented a pressure-gradient correlation based on measurements in wells. This correlation has been found to provide accurate predictions in high-pressure wells and in high-production wells for flow through both tubing and annuli.2-5 However, when their method is checked on low pressure-low production wells or on wells with viscous crudes, serious discrepancies are found. As we shall see in the next section, this is due to the fact that their correlation factor, representing all irreversible energy losses, is given as a function of only one correlation group. Some important variables, such as gas-liquid ratio and liquid viscosity, are not incorporated in this group so that their specific effects are not accounted for. To study also the mechanism of vertical gas-liquid flow outside the ranges covered by the Poettmann-Carpenter publication and extensions, a laboratory investigation has been carried out. This study is founded on a pressure-gradient equation that is based on a pressure balance. To reduce the number of test runs required, a dimensional analysis has been carried out, followed by a selection of relevant dimensionless groups. These groups guided a subsequent experimental study, and with their aid the experimental program could be minimized while still covering the majority of the situations encountered in oilfield practice. In this paper the choice of a formula for the pressure gradient is discussed first. This is followed by a brief description of the experimental setup. Subsequently, the dimensional analysis is discussed and the relevant dimensionless groups are selected, resulting in the experimental program required. The general relationships of pressure gradient and liquid hold-up are then described; various flow patterns and a certain flow instability (so-called "heading") are discussed and a set of correlations is presented which shows a good agreement with the measurements and a few available field

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982

By E. W. Codington

The pebble-phosphates of Florida occur in a district roughly bounded on the north by the 28th parallel, on the east by an irregular line running a few miles east of Peace river and on the west by the Gulf of Mexico, and covering an area of about 4000 square miles. There seems to be no reason why the deposits should not extend farther south along the gulf coast. That section remains unprospected, transportation-facilities being non-existent. It is not intended in this paper to discuss the geology of these formations; but a word as to their probable origin will be perhaps the best method of giving a correct idea of their present position. Starting with a low, flat surface, with even less of superficial undulation than appears at present, an im-

Jan 1, 1896

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature microhardness of as-grown and annealed MoaC single crystals was measured on the (0001), {2110), and1012) planes using Knoop and Vickevs indenters at loads ranging front 25 to 1000 g. The orientatimz dependence of hardness with respect to crystal axes was also studied. The average random hardness of as-grown crystals was determined to be 1520 kg per sq nm. Annealing to 2000°C decreased. the average hardness by 150 units. An increase in hardness after annealing at 2200 ;C was noted. Optical and electron microscopy revealed slip and twin traces on all planes studied, as produced by mi-cvohavdness indentations. Basal (0001)(2i10) slip was determined to be the primary slip system and was substantiated by electron transmission microscopy. A secondary {1010)(2110) slip was produced by mi-crohardness indentations. The lattev also produced twinning- of the {10i2)[0001] type, as proven by electron diffraction. Electrical resistivity and elastic-modulus anisotropy were found and correlated with hardness anisotropy and Mo2C crystal structure. Elastic-modulus values were obtained by microhard-uess and ullrasonic methods. Bonding mechanism of Mo2C is discussed. ROOM-TEMPERATURE microhardness indentations are useful for studying hardness anisotropy, slip, and twinning in brittle materials. Slip has previously been produced in this manner in and WS~~.~ Recently, the authors5 reported slip of the {10i0)(11~0) type produced by high pressure and microhardness indentations on hexagonal TiBz (c/a = 1.066) single and polycrystals. This slip system was also reported by French and ~homas' and Taka-hashi and ~reise~ for hexagonal WC (c/a = 0.976) crystals. These results suggest that prismatic rather than basal slip is favored in hexagonal nonmetallic materials having a c/a ratio considerably less than the ideal (1.633). Buerger precession and cylindrical X-ray rotation patterns were previously' taken on cleaved sections of the Mo2C single crystals studied in this work. Th~y were found to be hexagonal MoaC with a. = 3.0233A, co = 4.7344A, and C/O = 1.5660. The latter ratio is close to that of the beryllium metal (c/a = 1.57), which slips primarily on the (0001) plane: but also slips on the (1010) planes.'0 ~irconium" (c/u = 1.59) and titanium12 (c/o = 1.59) deform mainly by slip on nonbasal planes which contain a close-packed direction. This is due to the fact that for these two metals the initial resolved shear stress for slip on the (10i0) prismatic planes is lower than that on the (0001) plane. The prominence of basal rather than prismatic slip in metals of high c/o ratios is shown by cadmium (c/a = 1.89), zinc (c/a = 1.86), and magnesium (c/a = 1.62) which deform mainly by basal slip. However, in case of the latter, by stressing magnesium crystals in tension or compression parallel to the basal plane, slip on (10i0) planes can also be produced.13 Several hardness values for polycrystalline Mo2C are reported in the literature: Biickle ' and Samsonov'~ give a value of 1800 and 1479 kg per sq mm, respectively, at a 100-g load; and Kieffer and Benesovsk~'~ report a value of 1950 kg per sq mm at a 50-g load. ~ott'~ reports a Vickers hardness value of 2000 kg per sq mm, with the load unspecified. A Rockwell A hardness value of RA = 88 has also been reported.'' In the present work, for comparison with single-crystal Mo2C hardness values, a Khnloo value of 1600 It 150 kg per sq mm was found on 99.6 pct pure and 99 pct dense hot-pressed Mo2C. This work was undertaken partly to explain the considerable differences in hardness values reported for polycrystalline Mo2C. EXPERIMENTAL The Mo2C single crystals investigated were prepared by a Verneuil-type process using an electric arc by the Linde Co. of the Union Carbide Corp.lg The largest specimens grown were boules 7 mm in diam by 40 mm in length. The crystals had an average density of 9.04 g per cu cm, with a Mo + C content of 99.8 wt pct. The major impurities were: 100 ppm each Na, Zr, and Ca; 85 ppm 0, 55 ppm Fe, and 10 ppm each Cr and Ta. The crystals were found to be carbon-poor, the average carbon content being 5.73 wt pct (stoichiometric value is 5.89 pct). The molybdenum content was found to be 94.08 pct, which is nearly stoichiometric. Electron-microprobe traverses of selected specimens were done with a Phillips-AMR microanalyzer. Thin-film and carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to optical and electron-optical studies, specimens were mounted in Lucite and polished on a vibratory polisher using diamond-paste grades ranging from 9-1 p and Linde A powder for up to 48 hr. Dilute nitric acid was used for thin-section polishing and chemical etching for 1-15 min. Electrical-resistivity measurements at room temperature were taken with a Rubicon bridge, using gold contacts. For hardness measurements, a Tukon Microhardness Tester Type FB with Knoop and Vickers indenters was used. Measurements were taken at loads ranging from 25 to 1000 g; however, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Indentations of cracking classes 1 and 2 only were considered for hardness determinations.20)21 (There are six cracking classes, ranging from "class 1" for a perfect inden-

Jan 1, 1967

By Werner Engelmaier

Constant-strain rotating-bending fatigue tests were conducted on 2024-T3 aluminum alloy constant-strain McAdams-type specimens in ultrahigh vacuum, 10-lo Torr, and in atmospheric air. In the elastic strain range the ratio of vacuum-to-air fatigue life varied from about 10 at a maximum bending stress of 37 ksi to near unity at the endurance limit. After 10 pct of the fatigue life, intergvanular microcracks appeared on the surface which did not appreciably propagate further until the last 5 pct of the fatigue life, where trans-granular cracks propagating first in slip-plane cracking and then in the stress-dominated mode led to failure. No reduction in residual tensile strength resulted from the fatigue of the specimens short of fracture. The mechanism governing the fatigue life operates between the occurrence of the intergranular microcracks and the initiation of the trans granular cracks. MORE than forty years ago, Mc Adam' and Haigh2 published the first systematic studies showing that the fatigue properties of metals were greatly affected by environments. Gough and sopwith3 found in a later study that the fatigue life of metals subject to corrosion can be substantially increased by reducing the atmospheric pressure. This and their later work4'5 was, however, done in a vacuum of only 10~3 Torr. Subsequent studies6-' at a vacuum of 10- Torr showed that water vapor is the primary agent affecting the fatigue properties of aluminum alloys. Only recently was ultrahigh vacuum used for fatigue studied.l Various theories have been put forward to explain this phenomenon. Wadsworth and Hutchings12 postulated that cracks form very early in the test and that the chemical attack by the corrosive components of the atmosphere at the root of the cracks enhances the speed of the crack propagation. They also noted that chemisorbed layers of gas on the fresh crack surfaces prevent cold welding of the crack and make the separation irreversible. Ham and Reichenbach, on the other hand, reported that their specimens showed no cracks after a run in vacuum, even though the runs were long enough to have caused the specimen to fracture in atmospheric air. They also reported that in argon at 0.14 Torr the fatigue life was about 5 times longer than at 7 X lo-' Torr. Jacisinll reported that fatigue tests in dry nitrogen showed results close to those obtained in ultrahigh vacuum. The present experiment was designed to determine the extent to which cumulative fatigue damage, i.e., the accumulation of length of fatigue cracks, reduces the residual static tensile strength of an aluminum alloy in both ultrahigh vacuum and atmospheric air and to obtain fatigue-life data for this aluminum alloy at various strains. It was also hoped that information ex- tracted from these data might support one of the previously mentioned theories. 1) EXPERIMENT Test Specimens. The material tested was commer-cial 2024-T3 aluminum alloy. In addition to aluminum, this alloy contains approximately 4.4 pct Cu, 0.5 pct Fe, 0.5 pct Si, 0.6 pct Mn, 1.5 pct Mg, plus smaller amounts of other elements.13 Some typical mechanical properties of this aluminum alloy are listed in Table I.'~ The material was used in the as-received condition, i.e., solution-treated and cold-worked. Mc Adam-type1' constant-stress specimens and notched fatigue specimens were machined from 4 -in. -diam rods, Fig. 1. The critical section of the McAdam-type samples was polished with a 45-deg spiral motion to a No. 8 microfinish. The notch in the notched specimens was machined on a lathe with a forming

Jan 1, 1969

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By Chas. Kohl

ABOUT 1929 an engineer was engaged to organize a Safety Department, lay out an educational program, and achieve a reduction in accident frequency. Due to the large number of employees, about 12,000, and the distances between the various properties, it was a big undertaking. Most of the workmen are from the Sierra and for generations have been agricultural people, with little conception of modern tools and machinery, and to a large degree are illiterate. However, gratifying results have been obtained, as evidenced by the accident frequency curve during the sixteen-year period. Safety offices have been established in each of the six major properties, staffed by men who devote their entire efforts to inspections of working conditions and equipment, instructions as to safe methods, and investigations of accidents. The Corporation is a member of the Inter-American Safety Council, receiving their publications and literature, which serve to keep us up to date and informed on modern methods. Dissemination of this material is accomplished chiefly through word-of-mouth and bulletin boards. When it is found that the accident rate is increasing in a certain occupation, as for instance underground haulage or mine hoisting, the operators so engaged are assembled and given renewed instructions on the safety code pertaining to their work. Inter-camp competitions in accident avoidance are being conducted, with annual awards for that unit having the lowest severity rate for the year.

Jan 1, 1945

By T. M. Berry

FOR the past several years it has been growing practice to install circular shafts at deep mining operations. Several factors have brought this about. Throughout eastern and midwestern coal fields circular shafts have been conventional for many years. Where large bodies of coal are mined, a production shaft may have a life of 20 to 30 years. Quantity production is essential; therefore the shaft must have a large cross-sectional area for larger skips and cages. Mechanical mining has become a necessity if a company is to stay in business today. Continuous mining machines and cutting, loading, and hauling equipment must be taken in and out of the mines. If the access shaft is not large enough there will be expensive dismantling and assembling. This has become a problem at many operations, particularly in the western sections where ore was originally mucked by hand into small cars and hoisted by a skip through a narrow rectangular shaft having small compartments. Mechanical loaders must be dismantled to wheelbarrow size to go into these mines.

Jan 7, 1957

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood' suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener's mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh's5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

By James E. McNulty

Coal reserve estimates are prepared using a simple equation: the product of area, bed thickness, density and recovery factors. Each of these elements involves a degree of risk based on certain assumptions. Reserve area, thickness and density rely on certain physical data whose accuracy, reliability and sufficiency may be problematical. Estimates of recovery factors for mining and coal preparation are often subjective. Most reserve estimates assume, sometimes incorrectly, that the subject reserves will be completely extracted. The principle that certain coal resources are reserves, if they can be considered economically recoverable at the time of determination, needs to be reexamined in the light of recent market cycles. Reserve estimating requires the exercise of judgments, the validity of which reflect the qualifications, experience and objectivity of the estimator.

Jan 1, 1985

National Minerals Advisory Council A meeting of the National Minerals Advisory Council on August 3rd in Washington, D. C., indicated the vitally important part that the mining industry is to play in the mobilization program. Director James Boyd of the Bureau of Mines told the Council that the Department of the Interior would review the recommendations of all the Council's commodity committees with regard for mobilization planning in the light of the changed international picture. The Council was requested to reactivate its commodity committees and have them gather all available data on supplies, their sources and availability and present and potential production of the minerals and metals represented on each committee. Data on labor, machinery, transportation, automotive and stationary equipment, power, fuel, lumber, water supply are a few of the important items called for in the reports, which are to be presented at a meeting of the Council on September 1 at Salt Lake City. The material in the reports will become the basis for discussing metal and mineral requirements at that time. Discussion at the meeting bared several $64 questions, probably the most important of which are the following: 1. Which of the war-essential metals and minerals and in what quantities can we reasonably expect to get them from abroad under threat of submarines? 2. How are we going to meet the manpower problem posed by (a) migration of labor from mining to manufacturing since the end of World War II and (b) the draft and the calling up of reservists? Opinion was expressed by industry spokesman at the meeting that the function of complying with mobilization requirements be left to those in the industry itself; that is, those having the "know how." This view contended that any administrating governmental agency should be kept as small and streamlined as possible. There was general sentiment against the reactivation of the wartime Premium Price Plan or other bonus plans as a stimulus to production. The thought was emphasized that what was needed was a change in the basic conditions which have fostered the decline in domestic mining activity in the postwar years. One such condition, long overdue for correction, is the tax structure as it applies to mining enterprises. Many quarters both in industry and in government favor tax relief along the lines suggested in the six tax recommendations by the Council to the Secretary of the Interior last December. The Council adopted a resolution expressing a feeling that the following tax recommendations are still feasible and desirable and will accomplish as much toward increasing exploration for new deposits (thereby subsequently increasing production) as will government loans for exploration: (1) Losses from unprofitable ventures should be allowed corporations, partnerships, or individuals as ordinary deduction against current income. (2) Development costs after discovery should be recognized as operating expenses. (3) Allowance for depletion should be made to the stockholder as well as to the corporation. (4) Income should not be taxed without full allowance for losses of loss years. (5) Adequate allowances for percentage depletion should be made. A discussion of the manpower problem led to the Council's acceptance of a resolution advising that "military authorities should proceed with caution in depriving the mining and metallurgical industry of its manpower." The resolution strongly urged that no personnel "directly engaged in exploration, development, production or supervision (of strategic and critical materials) should be drafted for the armed forces, at least until the anticipated demands upon these producers are clarified." Stockpiles The Munitions Board's "Stockpile Report to the Congress" of July 23, 1950 revealed: (1) The total estimated value of the stockpile objective is $4,051,714,510 at the close of fiscal year 1950. (2) The total value of the stockpile on hand, at the close of fiscal 1950 was $1,556,154,352 or 38.4 pct of the total stockpile objective. An additional $494,948,060 was on order, making a total of 50.6 pct on hand plus the amount on order. (3) Materials obtained for the stockpile by the ECA from January to June 1950 amounted to $13,112,085, while development projects by ECA during this period involved the expenditure of $9,322,000, mainly with counterpart funds. Shortly after the start of the Korean conflict it was felt that Congress ould appropriate greatly increased sums for the purchase of materials for the stockpile. This stimulus to the program may increase the dollar earnings of those European nations that are present or potential contractors in our stockpiling program. Such a development would mean that these nations could add to their gold reserves, thereby stabilizing their respective economies and hastening recovery. This seems to be the picture for the next six months anyway. The "bug" appears when it is realized that the increased threat of total world war actually may retard recovery in Europe as nations on the continent may feel inclined to devote more of their resources to defense programs. Industries Essential to Defense The Department of Commerce in response to a request by the Department of Defense issued on August 3, 1950 a "Tentative List of Essential Activities" as a "guide for calling up for active duty members of the civilian components of the Armed Forces." The list includes the following: Primary Metal Industries. Included herein are establishments engaged in the smelting and refining of ferrous and nonferrous metals from ore, pig, or scrap. Metal Mining. This category includes establishments primarily engaged in mining, developing mines or exploring for metallic minerals (ores). This group includes all ore dressing and beneficiating operations. Anthracite Mining, Bituminous Coal and Lignite Mining, Crude Petroleum and Natural Gas Extraction, Mining and Quarrying of Nonmetallic Minerals, Except Fuels. Challenge to the Mining Industry The source of our country's great strength lies in its capacity to produce. In times of stress such things as national morale and manpower are all-important but without a capable industrial machine we would be helpless. That machine must be fed with minerals and metals in order to generate and maintain momentum sufficient to insure success. Consequences of the lack of adequate supplies of essential metals and minerals to increase and sustain our industrial power are not pleasant to contemplate. It is absolutely imperative that we put forth Herculean effort to guarantee ample supplies of such essential materials as copper, lead, zinc, manganese, antimony, mercury, tungsten, tin, chromite, nickel, cobalt, iron ore and rubber. The mining industry faces a challenge more serious than ever existed before in the history of our country. The industry must be equal to the task.

Jan 9, 1950

By A. J. Phillips, A. A. Smith, J. S. Smart

THE preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in properties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. PREPARATION OF HIGH-PURITY COPPER The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuS04-H2SO4 electrolyte using bagged anodes, low current .density (5 amp. per sq. ft.) and low temperature (25°C. max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe 2(S04)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then refiltered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2S04 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 434 by 43a by I-in anodes cast from high-quality electrolytic wire bar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars-which would result in fouling of the contacts and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem's pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem's patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its president and its secretary, may be published in Mining and Metallurgy or the Directory of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as Student Associates or Junior Members of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1. A copy of Mining and Metallurgy free; 2. The use of Employment Service; 3. The use of Mining and Metallurgy for publicity purposes, such as printing notices of their activities, etc.; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engineering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to the nature, membership and officers. The following list gives the names of the Affiliated Student Societies as of December 1, 1929, and their presidents and secretaries.

Jan 1, 1929