Search Documents

By Rollin E. Hook, Attwell M. Adair

The response of CrzO3 and C~304 to various heat treatments was studied in are-melted iodide chromizim over the temperature range 1000" to 1750°C. These oxides, which are present as impurity phases in this material, were identified by X-ray diffraction teclzniques which were supplemented by optical metallop-aphy. As a function of increasing temperature, Crs04 is first observable in samples annealed at 1300°C and coexists with Cr2O3 (the low-temperature oxide) over a temperature range exceeding 200°C. As the temperature decreases, Cr3O4 dissolves with the concomitant precipttation of Cr2Y2. Both oxides precipitate predominantly at pain boundaries. The reactions which occur are involved with at least ternary equilibria, possibly due to iron which is present as an impurity in arc-melted iodide chromium. HILTY, Forgeng, and Folkman' reported in their investigation of the Fe-Cr-0 system that Cr3O4 (with about 8 pct Fe substituted for chromium) is a primary phase found in alloys with 9 or more pct Cr. They reported that this phase is stable only at high temperatures and that below the liquidus Cr3O4 is disproportionated into Cr2O3 and chromium-rich metal for both Fe-Cr-O alloys and in oxygen saturated pure chromium. Further, they proposed that CrsO4 forms by a peritectic reaction between Cr2O3 and the liquid. On the other hand, Hook, Garrett, and Adair2 found in their investigation of impurity phases formed in "pure" chromium (material consolidated from iodide chromium crystals) that Cr3O4 forms intergranularly and is stable as low as 1500°C which is 375OC below the melting point of chromium. The purpose of the research described herein is to determine the temperature range of stability of Cr3O4, and to show the nature of its decomposition. This further investigation indicates that Cr3O4 undoubtedly occurs in this material as low as 1300°C. The chromium studied was consolidated and fabricated from iodide chromium crystals (ICr-5) and contained Fe r 135 ppm, Si = 20 to 100 ppm, and 0 = 35 to 137 ppm. A complete chemical analysis is given elsewhere.' Annealing was conducted in 1 atm of purified helium and all samples were rapidly cooled (-200°C per sec) by withdrawing them from the furnace hot zone under a high flow rate of helium. The details of the electrolytic-etching technique and electrolytic-digestion techniques for preparation of insoluble residues for X-ray examination are given elsewhere also.' EXPERIMENTAL RESULTS The Starting Material. The as-swaged rod (final swaging done at 900°C) had a wrought grain structure and contained a dispersion of CrzO3 inclusions of maximum particle size of about 2 or 3 p, Fig. 1. The microstructure also contained a dispersed

Jan 1, 1964

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By Strathmore R. B. Cooke, William F. Stowasser

RESULTS presented in a previous paper1 have shown that the strength of fired pellets made from eastern Mesabi magnetite concentrates containing 8 to 9 pct Si02 as quartz and silicates is due to several processes which occur during firing. These are: l-recrystallization and cementation of the fragmented magnetite grains; 2-formation of slag from reaction between the quartz, silicates, and available ferrous iron, followed by slag-bonding of the magnetite grains; and 3-oxidation of the magnetite to hematite and subsequent recrystallization and grain growth of this constituent. Microscopic examination of all magnetite pellets fired in one operation in small and large-scale pilot plant furnaces and possessing normal strengths shows that the processes 1,2, and 3 have taken place; where strengths are low and the pellets are otherwise sub- normal, one or more of the processes has not occurred. For example, soft and friable red pellets may contain a central core of slag-bonded recrystallized magnetite which is strong enough in itself, but the shell contains only slightly recrystallized hematite, indicating that the maximum temperature reached was too low. Processes 1 and 2 can occur only under reducing conditions, as for example, when coal is intention- ally added to the original pellets; under neutral conditions, when pellets are fired in an inert atmosphere; or when pellets are brought so rapidly to temperature in an oxidizing atmosphere that oxygen diffusion to the core lags behind the recrystallization and slagging effects. This last-mentioned process has occurred in all pilot-plant shaft fur-

Jan 1, 1952

By S. Chander, D. W. Fuerstenau

The inherently sluggish nature of the reactions involving sulfide minerals, particularly molybdenite, in aqueous solutions under ambient flotation conditions make their investigation complicated and difficult. Since the physicochemical nature of sulfides is known to be controlled by electrochemical reactions, a number of attempts have been made in the past to study sulfide mineral-collector interactions through rest potential and electrode polarization measurements. The purpose of the present investigation was to study the interaction of potassium diethyldithiophosphate (KDTP) with molybdenite. In the present investigation of the interaction of KDTP at the molydenite surface, molybdenite electrode rest potential measurements and electrode polarization behavior were experimentally determined under various solution conditions. The standard reduction potential for the equilibrium between dithiophosphate ions (DTP-) and bis(diethoxythiophosphoryl)disulfide (DTP) [(DTP). + 2e :i7-± 2DTP- (1)] can be evaluated from the electrode rest potential measurements on a platinum electrode in deoxygenated KDTP solutions saturated with freshly prepared (DTP)2. Experimental A platinum wire was used as the electrode for potential measurements. Prior to each measurement the elec-

Jan 1, 1975

By H. O. Hofman

In the blast-furnace smelting of lead, copper and other non-ferrous metals, the largest part of the product obtained is slag. Its formation consumes more of the heat-energy of the fuel charged than any other chemical reaction that takes place. It is therefore of importance to know at what temperatures the different slags will form, so as to be able to choose in a given case the slag that will form at the right point in the operation, will keep the products thoroughly fluid, so as to insure a satisfactory separation, and will permit the consumption of fuel to be reduced to the lowest practicable point. While practical experience has brought out in a general way the leading differences as to the formation-temperatures of Rome silica—iron —lime slags, accurate details are still wanting. The object of the investigation here described was to supply some of these.* Prominent among the men who have worked on the fusibility of silicates are Lampadius, † Sefström,‡ Berthier,§

Jan 1, 1900

By T. H. Alden, H. W. Schadler

The strain rate dependence of the flow stress of the eutectoid Zn-Al alloy has been determined as a function of mechanical processing, microstructure, and temperature. The best superplastic properties result from the ultrafine, equiaxed structure produced by solution treatment and isothermal transformation at 0°C. Lamellar structures produced by isothermal transformation and coarse equiaxed structures produced by annealing also exhibit strain rate sensitivity in excess of 0.5, but at higher stresses and lower strain rates than the finest structure. Solution treatment and isothermal transformation eliminate the effect of prior processing history. Small composition variations in the binary alloy do not influence the mechanical properties. Below the eutectoid transformation temperature (.275C) increasing temperature lowers the flow stress at all strain rates. The data do not favor any of the present proposals for the mechanism of superplastic flow. ALLOYS of zinc and aluminum, near the eutectoid composition, have been investigated for: 1) the flow stress-strain rate and elongation behavior,1, 2) the transformation kinetics,3 and 3) structure,3"5 but the structure sensitivity of the mechanical properties is poorly understood. Using a near eutectoid alloy water-quenched from 380°C, Backofen et aL2 estab- high and increases with increasing strain rate. They found a correlation between strain rate sensitivity and tensile elongation as expected from the increased resistance to necking that a high strain rate sensitivity provides.296 The large elongation at high strain rates is attractive for metal forming. Since most other superplastic alloys7-l3 do not show high strain rate sensitivity at such a high strain rate (for the exception see Ref. 12) there is the possibility of a unique deformation mechanism for this alloy. The sensitivity of the mechanical properties of the eutectoid alloy to thermal history1 suggests a structure sensitivity that has not been demonstrated. Gar-wood and Hopkins3 identified a lamellar product for material transformed between 200" and 260°C. The size of the lamellae decreased with decreasing temperature. They also demonstrated that an unresolved transformation product formed below 200°C. A granular two-phase material was resolved for specimens quenched to below 150°C by Mitbauer and sauerwald4 who observed coarsening of the structure after annealing. The role of grain boundaries in superplastic deformation is suggested by the strong effect of grain refinement in encouraging this phenomenon at high strain rateS7-11, 13 and is emphasized in several proposals about rnechanism7, 8, 12 and in a theory14 of high-temperature deformation. Alden8 showed metallographic evidence that grain boundary sliding is occurring extensively at strain rates where m is large but less at high strain rates where normal plasticity is observed. Holt and Backofen10 have shown that sliding also oc-

Jan 1, 1969

HAVING already shown you the methods of making the moulds for casting and how they are to be prepared so that they may receive the melted metals well, it is now necessary, in order to complete the casting with perfection, that I show you not only the operations and instruments by which metals are softened, but also how metals can be made as liquid and fluid as water so they may easily enter into all the hollows of the moulds that you have made. Of these, besides the fire which is the prime agent, there is a very powerful furnace, which is called a reverberator.* I believe this is chosen not only for convenience but also because it is necessary in large casts. This is made of baked bricks, or of crude ones if desired or of suitable fire-resistant stones. Although all masters have the same objective, each one proceeds to make this kind of furnace according to his own ideas so that it can be said that there are almost as many different shapes of such furnaces as there are masters. This can be seen in the place that contains the metal, which is of such a shape that the force of the fire may operate better. Thus some masters are called good who, seeing no farther than what has been shown them, make them circular like a bread oven. Some others make them oval across the fire en- trance, while others extend them lengthwise. Also, there are some who make a single outlet for the flames, some two, and some three. Some make the entrance for the fire high and narrow and others, wide and low. The same is true of the place where the flames are generated, which is called the firebox. Some put the wood in from the side, some lengthwise in the same direction as the entrance for the flames, and some from above by means of a little hole. Also, one makes the vault low, and another makes it high. And while one puts an entrance for air underneath so that the

Jan 1, 1942

By David White

In these days, when detailed investigations of stratigraphy, structure, and sand conditions so frequently result in the discovery of new oil fields, and applause from oil companies and the public, geologists do well to walk humbly, and punctiliously to admit that the geologic principles controlling the distribution of oil and gas have as yet been discovered only in part, and that what remains yet to be learned is probably vastly more than what is already known. The few experiments already attempted have been fragmentary, and somewhat desultory, and however positive each of us may be with respect to certain theoretical conclusions, many of the fundamental questions as to the origin and mode of occurrence of petroleum are subject to radical disagreement. Of the chemical changes attending the generation of petroleum from organic matter, little is actually known. Most of the postulated formulas are liable to be misleading, through ignorance of essential factors. Open-minded-ness is therefore a prime essential at the present stage of our science. Nevertheless, adopting the hypothesis that oil originates in some manner fundamentally connected with the organic theory, and in possible departure from such open-mindedness, the writer will pay no attention to the so-called inorganic theory, since every attempt to apply this theory to the study of old oil fields, or to the discovery of new ones, affords cumulative evidence of its inadequacy. In this paper, some of the factors affecting the occurrence of petroleum that the writer believes worthy of consideration by the prospector for oil in any new region will be discussed. Some of these, which arc less generaLly understood, will be considercd somewhat in detail. Other points, the significance of which cannot now be determined, require more field study, and for that reason are here brought to the attention of the field geologist. On the other hand, certain theoretical points which do not bear especially on the oil possibilities of a new region will be given little or no attention. The main topics that will be discussed are: (1) sufficiency of carbonaceous detritus and residues in the oil-forming rocks; (2) stage of carbonization of the organic matter in the oil-bearing formations; (3) folding of the strata; (4) thickness of sedimentary formations; (5) conditions of deposition.

Jan 1, 1921

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By C. S. Blair

THE development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Ala-bama, in 1908 was an innovation probably unique for any mining organ-ization south of the Ohio River, At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much (of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator diffi-culties in his future operations, which the latter had not anticipated. Eventually, however, -the value of having these data became ap to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1933

Discussion of the paper of H. M. WARREN, A. S. BIESECEKER and E. J. POWELL, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 181 to 193. R.. V. NORRIS, Wilkes-Barre, Pa.-For many years the power requirements of breakers designed in the Anthracite. Region have been based on calculations made from indicator diagrams taken during operation, with various sections of machinery idle; these, while giving reasonably accurate figures, gave no intimation of the peak loads which have been shown so clearly in the paper. The high-speed flywheel for breaker rolls is new and shows a remarkable saving in peak power required, besides eliminating the stalling of the rolls from overload. The figures given are so far in advance of anything previously published that they will undoubtedly be used as a basis for future breaker design. It is to be hoped that the authors will continue this investigation and extend their paper by a description of the motors found best suited for this work. WILLIAM KENT, Montclair, N. J.-I notice on p. 187 reference is made to one of the difficulties being the starting torque, and it is proposed to use roller or ball bearings in order to decrease the high starting torque. I suggest that. before the roller or ball bearings are put in, an investigation be made as to the amount of the starting torque, as shown by wattmeter measurements and as to what the starting torque ought to be, theoretically, according to the energy formula; that is, how much starting torque is required to accelerate the rotating mass in a given number of seconds up to full speed. Having secured this information it may be found the amount to be saved by roller bearings is not very great. If it appears that roller bearings will not greatly decrease the starting torque, the next thing to be done is to have a special design of motor in which there is a field that can be made very strong at the start, by the use of extra poles or other means, and the next thing that may be done is to increase the speed from 10,000 r.p.m. to 25,000, which can be done with wire-wound flywheels, especially if the wires are made of vanadium steel.

Jan 5, 1916

THE second part of the mould for making guns is the core. Without this the space could not be made where the powder is to be and through which the ball, impelled by the fire, can pass and take flight. To make this it is necessary to take two things into consideration, because they are very important. One is what you are to make it on so that it may be supported and kept true. The other is what composition of clay will stand up during casting and yet not be very difficult to extract from the body of the finished gun. For the first, it is found that only an iron spindle of a suitable thickness is able to support the weight of the clay without bending under the heat of the fire or wobbling as it is turned on its journals or when handled. This should be a braccio or more longer than the mould of the gun and worked exactly round, straight, and well tapered like a spindle; above all every one of its joints should be well secured and solid. At the upper end a per-orated heel should be made, and lower down, exactly at the point corresponding to the length of the mould, are one or two other holes through which the little crossbars can be passed that fasten the core to the outer mould and also serve for constructing the disc. Now this iron is to be arranged on two trestles, pivoted so that it may turn truly when rotated. In order that it may not run up and down, make a little iron fork which engages a notch made with a file at the foot, and another at the head. After this, you must prepare clay for the core which is well made and tenacious ,enough not to crack. Fint take care that there are no pebbles in it and that it is composed of a small amount of cloth clippings and much sifted horse dung and some washed and clean wash ashes so that it may be of a tender and crumbly consistency in order that it may later be more easily extracted from the space inside the gun. In the same way, in order that you may be able to take out the iron piece at the same time, first cover it with ashes, and then wrap it all over with a rope of ordinary thickness, leaving a dito of the iron uncovered in every palmo length. [86] Alternatively, you may cover it all very tightly with hemp tow in the same way after it has been covered with ashes. Or heat your iron considerably and then cover it all to the thickness of a good cord with wash ashes or powdered charcoal that has been made into a paste with a little

Jan 1, 1942

By James J. Wise

INTRODUCTION One basic design feature utilized in all caving and sublevel stoping techniques is the drawpoint. These draw- points may be located on sublevels when using sublevel caving methods, or may be located at the floor pillar when using block caving, sublevel stoping, or vertical crater retreat methods. How the drawpoint is designed and developed, how the ore is withdrawn from it, and how the ore is hauled to the shaft or portal encompasses the loading and hauling function. Historically, predominate loading and hauling equipment for caving and sublevel stoping has been scraper slushes, air powered overshot loaders, and rail mounted train haulage. All of this equipment has two common constraints. 1. The equipment locked into specific work sites and is not easily shifted to another work site. This constraint can often lead to low utilization and low productivity of the equipment. 2. The equipment is designed to work in the horizontal plane, which requires that the various horizontally-oriented working levels be connected by vertical raises. Vertical development by means of raises is not only increasingly expensive, but also is not well adapted to movement of large equipment into the s topes. In the last 20 years, two revolutionary labor saving concepts have become common in caving and sublevel stoping. 1. Long-hole drilling, which has mechanized the development of the drawpoint extraction structures as well as the actual stoping and undercutting. 2. Vertical access by means of trackless ramps between levels, and the consequent use of rubber-tired vehicles not only for loading and hauling ore, but also for the rapid movement of men, material, and equipment into the stopes. The introduction of trackless mining systems for loading and hauling has not been easy. Mine planners have had to re-orient their thinking to the larger operating space required by trackless equipment. Larger access drifts have necessitated reconsideration of mine layouts to insure proper ground support. Spiral ramp developments were often laid out on slopes steeper than the equipment could negotiate economically. Mine operators had to accept the added responsibility of roadway maintenance, water removal, increased ventilation, and more technical mechanical maintenance. As the mine operators enthusiastically embraced the superior productivity of trackless mining systems, they some- times disregarded opportunities to combine the older types of equipment with trackless vehicles to maximize productivity at lowest cost. In order to gain a proper perspective on this problem, it is necessary to review the various techniques of loading and hauling and to become more aware of the advantages or disadvantages that each system or combination contributes. LOADING Loading consists of two functions, (1) primary loading from a drawpoint and (2) secondary loading into long- haul system, a truck, train, or possibly a belt conveyor. Mine planners have four basic loading systems available to fit various operating conditions. These are, (1) gravity, (2) scrapers, (3) rail-mounted loaders, and (4) trackless loaders. Each system can produce optimum results under specific conditions. Gravity Loading Gravity loading is probably the oldest system in general use today.

Jan 1, 1981

By Robert T. Howard, Morris Cohen

THE purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature trans- formations have been summarized recently by Troiano and Greninger.1 Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation [(M,)] during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transfoi mation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metallographic3 and dilatmetric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Steward7 have shown that the Greninger-Troiano metallographic techniques may be used not only for [M,] determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below [M,] in fourteen commercial steels. In the present paper, the Greninger- Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M,, thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. EXPERIMENTAL DETAILS Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M, temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1947

By AIME AIME

Air transport supplants the old methods. The 3-piece canoe fits in the plane and likewise makes possible not a bad division of labor over a 5-mile portage

Jan 1, 1933

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By Frank A. Wilder

The most important process in a gypsum mill is calcining the crude mineral. There seems, however, to be little progress or change in calcining methods. This would not be surprising if the industry was not, in other ways, developing. The demand for gypsum in its various forms, however, is growing rapidly. The output has more than doubled in six years, while the value of gypsum products, through the introduction of higher priced. specialties like wall board, has nearly trebled in the same period. In other industries, under somewhat similar conditions, calcining in rotating cylinders, either by direct or indirect heat, has replaced the method that still prevails in gypsum mills. Efforts were made to use rotary calciners in manufacturing plaster of Paris in the early days of the industry in America; 25 years ago rotary calciners were in use in Germany. At that time there was great diversity of opinion in regard to their merit. In 1923, the output of calcined gypsum in the United States was 3,101,378 tons. About nine-tenths of this material was calcined in kettles, the remainder in rotary calciners. The ratio was about the same 10 years ago. During these 10 years, rotary calcining made relatively no gains, and there were no important changes in the construction of kettles. In their manipulation, the only change of consequence was in connection with the length of time that the gypsum is left in the kettle. For wall-plaster purposes, all producers who had not previously done so changed from second-settled to first-settled calcined gypsum, thereby reducing production costs and improving the plasticity and sand-carrying capacity of their plaster. Nevertheless, in the few mills in which they were installed, rotary calciners continue to operate, with possibly one or two exceptions, and to be highly successful. In these 10 years, the Cummer type of rotary calciner has disappeared. All rotaries now used are of the cement-mill type with a diameter of 6 or 7 ft. and length of 80 to 120 feet.

Jan 1, 1925

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By J. C. Williams

THE operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent-namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components-that is, the silica, alumina, iron and lime-and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1946

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947