Search Documents

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949

By F. H. Deily, D. S. Rowley, R. J. Howe

By Thomas Henderson

Strategically, intermaterials competition is important to companies involved in raw materials extraction, smelting, refining or other processing, semi-finished and finished goods fabrication, and end-use consumers. In other words, just about every company involved in manufacturing. The array of materials covered by other papers in this session is testimony to the subject's breadth. In trying to provide an over- view of such a broad topic, the purpose has been to relate some of the common characteristics of the markets, economics and technology of raw materials, and to describe some of the ways in which Intermaterials competition impacts the markets, economics and technology of raw materials.

Jan 1, 1982

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968

By Arthur Notman

TO present some idea of the magnitude of the gold-mining industry of Canada and the world, the records of 106 gold-mining companies currently paying dividends have been studied. Forty of these are in Canada, and 37 on the Rand in South Africa, these being all the straight gold-mining companies that paid dividends in the two areas in 1938. None of the base-metal companies that produce gold as a by- product, or even as a major fraction of the value of their total product, have beezl included. In addition, a group of 29 similar companies from Southern Rhodesia and the Gold Coast in Africa, India, Australia, Manchuria, Philippine Islands, the

Jan 1, 1939

By Henry Howe

(New York Meeting, October, 1913.) The Equilibrium. Position of A 1.-Some of the most important data on this subject are collected in Table I. Definition of Ae 1-Just as we call A 1 of rising temperature Ac 1, and that of falling temperature Ar 1, so we may give the symbol Ae 1 to the equilibrium position of A 1. Preliminary Assumptions.-In deciding what weight to assign the various data, and indeed what data are to count, three assumptions should be made. These are: 1. The corollary from the phase rule, that the temperature of Ae 1 is constant and independent of the carbon content, though, of course, it may be changed by the presence of other elements. 2. That because neither in heating nor in cooling can the transformation begin before the temperature reaches Ae 1, though it may be delayed by lag till after the temperature has passed beyond Ae 1, therefore Ae 1 should be at or below the observed beginning of Ac 1 and at or above the observed beginning of Ar 1, and, a fortiori, it should be at or below the observed maximum of Ac 1, and at or above the observed maximum of Ar 1. It may be necessary to take these maxima into consideration in view of the experimental difficulty of detecting these beginnings.

Jan 6, 1913

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969

By Alan M. Bateman

Before World War II we proudly considered that we were the nation of all the world most richly endowed in mineral resources. We knew it was no accident that those countries abundantly supplied with mineral resources became the great manufacturing nations, and the politically and militarily strong ones; and that our own great industrial cities sprang up where coal and iron met. We all reallized, especially we of the mining profession, that the energy of fuels and the solidity of metals spelled industrial growth and in turn industrial might and that other nations came to regard mineral self-sufficiency as one of the chief goalsof economic nationalism.

Jan 1, 1949

By F. C. Blake

The apparatus which I shall describe in this paper has been in ase for some time at the laboratory of the Pennsylvania Lead Company's works, and has been found to give good results, and to be simple and convenient. Steam Bath.—This steam bath is shown by Figs. 1, 2,3 and 4. It is made of sheet copper, about one-twelfth of an inch thick, the joints being brazed, and is used for heating the bottles in which the silver samples are dissolved,-previous to the fineness determina-

Jan 1, 1882

By Sherwin F. Kelly

MANY baffling problems of crustal geology-of warping and folding, elevation, subsidence, and great dislocations of the earth's surface-may now be on the verge of yielding to the science of geophysics. Electric, magnetic, gravitational, geothermal, and seismic methods are being turned to the gathering of geological evidence buried by deep layers of rock, or lying beneath the waters of the oceans. In this hope, B. L. Miller expresses the opinion that these geophysical studies will sup- ply useful data bearing-on some of the more theoretical problems of North American geology. Among these for example, is the explanation of how Appalachia disappeared. This ancient land mass is supposed to have foundered beneath the Atlantic Ocean after the close of the Paleozoic era and the question arises, was it warped or faulted downward? The geophysical data, though meagre, indicate that the surface of the dense, basal rocks, the probable remnant of ancient Appalachia now underlying the Continental Shelf, slopes downwards to a depth of some two miles below sea level at a distance of 140 mi. from shore: thus suggesting that the subsidence was the result of warping downward rather than abrupt faulting.

Jan 1, 1938

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By E. A. Stevens

It has been ascertained in recent years that certain rocktypes, geological formations and structural conditions may be used as fairly reliable guides, when prospecting in recognized mineral belts or milling districts, with a reasonable certainty of discovering "pay-ore;" and that such is considered as a practically established conclusion may be inferred from a perusal of the recent reports of the U. S. Geological Survey and the literature of the several scientific societies discussing mining, geology, and kindred subjects. Cripple Creek is no exception to this conclusion, and the

Jan 1, 1903

By Theodore Marvin

FOLLOWING the receipt of questionnaires from many parts of the world, the Aviation Committee is completing a review of the use of aviation in mining and petroleum operations. The summary of this study should be available at the 1937 Annual Meeting in New York City, at which time several papers will be presented on specific application of aerial geologizing. From the reports received, there is little question that this air branch of mining is here to stay. Of course, the transportation of personnel arid material continues to merit attention but it is in the division of aerial geologizing that flying is finding its widest, most technical application.

Jan 1, 1937

By JOSEPH MACDONALD

STRIPPED of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it, and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If be fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be divided into a number of main departments, which are subdivided into minor departments. Each main department should be under the immediate charge of a superintendent, or a foreman, and each minor department under a shift-boss. Organized in this way, and with all the principal centers of activity connected by telephone, the manager can keep in touch at all times with the details of every branch of the business, and be in a position to perform effectively the full duty of manager. The ?total cost of mining operations may be broadly divided under the heads of Labor, Supplies, and Marketing. Of these, it will be found, on averaging a number of cases, that the cost of labor will be about two-thirds of the total cost. The importance, therefore, of an efficient labor-department will be apparent. This department must be sub-divided and organized differently, according to the peculiar conditions at each mine, and no one system, however well suited for one particu-

Jan 1, 1909

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the' utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up ' the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926