Search Documents

By J. Kent Smith

THE object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent, furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575° F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450° F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450° F.) were reheated for varying periods of time at 575° F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Che, C. W. Spencer, C. A. Steidel, Yu Li

Grain boundary grooving as it occurs in a 5.5-deg simple-tilt nickel bicrystal immersed in a saturated Ni-S liquid has been studied. A 1/3 (t= time) dependence for the depth of the groove indicates that the rate -controlling meckanism for groove developvnent is volume diffusion in the liquid. The activation energy for the diffusive process is estimated at 15 kcal per mole. Using an extended form of W. W. Mullins&apos; analysis for grooving reactions, a computer is employed to fit the appropriate diffusion equation by a numerical method. From the analysis a possible method of measuring L.S. the solid-liquid interfacial tension is demonstrated. WHEN a polycrystalline solid is heated in equilibrium with a saturated fluid phase, grooves will form at the intersections of the grain boundaries and surface. The equilibrium root angle of these grooves is determined by the balance between the grain boundary and solid-fluid interfacial tensions. The grooves deepen and widen with time due to a difference in chemical potential between the flat interface and the curved interface of the groove. In this investigation solid-liquid interaction at a grain boundary is studied, with the object to determine the mechanism of grain boundary grooving in the presence of a saturated liquid. Extension of Mullin analysis then permits the estimation of the solid-liquid interfacial tension. Herring has demonstrated by dimensional analysis that the quasi-steady state change of the dimensions of a small particle during sintering is proportional flow, evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, respectively, if geometric similarity of consecutive configurations of the particles holds. Mullins has extended this analysis to grain boundary grooving. In the case of shallow grooves he solves the diffusion equations for evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, and obtains the same time dependence for any linear dimension of a groove as Herring found for the change in dimension of small particles. In Mullins&apos; analysis2&apos;3 grain boundary grooving of a bicrystal by volume diffusion in the presence of a saturated fluid phase was considered. Several assumptions were made prior to the analysis: 1) the solid-fluid interfacial tension is independent of crystallographic orientation; 2) the Gibbs-Thompson equation relating curvature and chemical potential is applicable at the solid-fluid interface; 3) the relaxation time of the diffusion field is small compared with the time for appreciable changes in the curvature of the groove, so that the diffusion is divergence-less; and 4) the groove has a small slope relative to the initial flat interface. Usually this last condition is fulfilled only for solid-gas systems. The solution of the diffusion equation under the above conditions produces a t1/3 dependence for any linear dimension of the groove in the case where volume diffusion is rate-controlling. The t1/3 dependence is valid because geometric similarity of the grooves exists for all time. EXPERIMENT In the experiment a 5.5-deg nickel bicrystal of <100> simple-tilt orientation was used.4 Grooving was studied in the presence of a saturated Ni-S liquid alloy as a function of time at 750°, 800°, 850°, and 900°C. A low-angle bicrystal was chosen for study to insure that 2L.S. > .b., where l.s.

Jan 1, 1964

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-&apos; pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.&apos; and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By Edward Capillon

THE problem of scrap is probably of greater importance inn the production of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of the base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is. not generally feasible to assay every shop remelt it follows that the possibilities of lost values are large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base, metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys.

Jan 1, 1930

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By Ralph E. Grim

THE technology of clay minerals is defined, for the purpose of this review, as- the application of fundamental data regarding clay minerals, and techniques of handling them, to the various industries, arts, and professions concerned with clay materials. The aim of the paper is to narrate recent developments in clay mineral technology. This review does not claim to be complete, and perhaps gives undue emphasis to matters that have been worked on in the author&apos;s laboratory or with which he has some other connection. In the United States in recent years, particularly since the end of World War 11, interest in clay mineralogy has increased greatly. Many laboratories in many different fields have embarked on studies of clay minerals but unfortunately much of this work has not been published. CERAMICS In the field of ceramics, in recent years, a great deal of interest has developed in clay mineralogy. Papers too numerous to be reviewed here have been published portraying the clay mineral composition of substantially all the important types of ceramic clays in all countries. There has been a growing tendency to attempt to solve processing problems on the basis of clay mineral data rather than chemical analytical data. Likewise, there is an in- creasing tendency to control the characteristics of raw materials on the basis of clay mineral composition rather than chemical composition. In the United States in the last few years something like 50 differential thermal analyzers have been set up, and many are for the sole purpose of controlling raw material and processing. The ceramic industry is currently increasing its attention to the influence of exchangeable ions and soluble salts on physical properties. Ion concentration in clay suspensions has long been a matter of interest, but now it is also of interest in clays in the plastic state because of its recognized importance in the plastic, shrinkage, and bonding properties of clays. Students of clay have long recognized that an understanding of the plastic properties of clays is based on an understanding of the character of the water in clay-water systems, the nature of the binding force between individual clay mineral particles, and the factors that control the character of the water and the nature of the bonding force. In the last few years, some extremely important contributions have greatly increased the understanding of the nature of water adsorbed on the clay mineral surfaces. In this connection the work

Jan 1, 1952

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By A. T. Yu

Over the last 80 years the conveyor belt has advanced from the troughed rubber belt to those with standard steel cable cores and those which can navigate curves or climb steep inclines. Now the latest generation of belt conveyors can claim hitherto unheard of capacities of 20,000 tph and single flight lengths well exceeding 16,000 feet. The stranded steel cable core belt is principally responsible for the spectacular improvement in load carrying ability of belt conveyors. The allowable working tension of these belts ranges from 2,500 lb per in. of belt width for 1/4 in. diam cable to 4,000 lb per in, for 3/8 in. diam cable. These ratings far exceed the 240 lb per in. per ply for rayon or nylon construction, and 30 lb per in. per ply for a lowcost cotton fabric.

Jan 1, 1970

By K. Huessener

Discussion of the paper of K. HUESSENER, presented at the New York. meeting, February, .1916, and printed in Bulletin No. -110, February, 1916, pp. 443 to 474. KARL NIBECKER, Youngstown, O.-It has been contended that the method of measuring the operation of a blast-furnace boiler plant by means of the amount of steam generated per pound of coke used in the blast furnace is not of any value and even that it is quite misleading. It has been found, in the plant with which I am connected, that, in general, a blast furnace will operate during a month so close to average. conditions that the average monthly measure of the plant efficiency is indicated by the number of pounds of steam made per pound of coke put into the furnace, neglecting the amount of iron made and the amount of gas used for heating the stoves. For some time, it has been our custom to keep a record of this figure and use it as a general indicator of the operating practice. In comparing this figure from two different plants we have found some difficulty, due to differing conditions. It is conceivable but not altogether probable that a slight difference in burden, kind of ore or coke, would account for this difference. The method of using the gas, whether washed or unwashed, and the plant arrangement, may affect this number. For several plants on which we have worked up this number, we have found that most of the ordinary running irregularities are eliminated during a run of a month or more and that the number is, therefore, satisfactory. In connection with a plot of the number of pounds of steam generated per pound of coke, we are also plotting the production of the furnaces and the pounds of coke used per ton of production. With these three curves plotted on the same sheet, we believe that the operating man has sufficient information to judge of the efficiency of his plant&apos; for any month.

Jan 5, 1916

By J. C. Wright

A practical program of education for workers of the mining industries is being formulated by the Federal Board for Vocational Education in cooperation with the states in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational education and for cooperation with the states in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the 1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manfactures Mines and quaRRies Employees.......... 7,405,313 1,109,410 Capital............. $18,428,269,706 53,380,525,841 Value of product..... $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all states have set up educational and technical standards for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some states, every miner must have a certificate, which is issued by the mine examining board only after an oral examination. Did these state laws not call for definite and comprehensive plans for the vocational education of men in the mining regions, the conditions

Jan 1, 1919

By Morris Cohen, William P. Kimball

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By Morris Cohen, William P. Kimball

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expressioll for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: , = Zlxl{xl - P) + ZsXsiP - xs) [I] Zl(xl -P)+ Zs{P - xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, xl and xs are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling. the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By William P. Kimball, Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By A. Becker, J. A. Slankis

Equipment has been developed to utilize natural 8 Hz electromagnetic fields to measure rock resistivities. Telluric and magnetotelluric surveys have detected resistivity variations associated with geological contacts and metallic sulfide deposits. The fundamenfa1 premises of these methods are illustrated by the results of surveys across a Pleistocene-Precambrian contact in the Ottawa Valley and a near-surface sulfide deposit in Northern Quebec. Such interfaces are characterized not only by variations in apparent resistivity, but also, unexpectedly by the spatial anisotropy of the electric fields and the presence of a strong vertical magnetic field component in their vicinity. Standard geophysical electrical and electromagnetic methods (Heiland, 1940) for the determination of the electrical properties of the ground and the search of good electrical conductors necessitate the use of a transmitter and receiver which are coupled galvanically or inductively through the ground. The electrical properties of the ground are deduced from either the transfer function, or the impulse response, of the transmitter — ground — receiver system. Where deep penetration is desired these methods require powerful transmitters whose weight and size increase the cost and reduce the speed of operation. It is possible however, to resort to another class of electrical prospecting methods which employ ambient, natural electromagnetic fields in place of a transmitter.&apos;-&apos; In the audio and subaudio frequency ranges, these fields are generated by thunderstorm activity. At some distance from the seat of the disturbance, the e.m. fields propagate as plane waves with a horizontal magnetic field component. The incident wave, of course, induces currents in the ground. Where the ground is homogeneous the relation between the horizontal magnetic and horizontal electric fields vectors is particularly simple:&apos; /E/ = \[SpT/H/ (1) where: /E/ = magnitude of horizontal electric field in millivolts/kilometer (RMS) /H/ = magnitude of the orthogonal inducing magnetic field in milligammas (RMS) p = rock resistivity in ohm-meters i = frequency of measurement in c/s In practice, the ground is seldom an homogeneous half space, lateral conductivity variations exist, (in the case of base metal prospecting these are the features actually sought) and the two field vectors are no longer simply related. The ratio of E to H is still useful, however, for the determination of an "apparent" ground resistivity. From a theoretical view point, the general problem of a two dimensional fault or dyke anomaly can be separated into two distinct cases. In the first case, where the e.m. energy propagates in a direction normal to the strike, the horizontal magnetic field remains constant and is oriented along the strike of the formation.3 As shown by d&apos;Erceville and Kunetz," all the information about the anomaly is contained in measurements of the electric field component. In fact, away from the interface, the electric fields are proportional to the square roots of the resistivities:

Jan 1, 1970

By J. Wyn Prior

The seismic refraction technique is probably the most popular geophysical method of bedrock profiling in geotechnical site investigations but is somewhat restricted by the inherent assumptions in the method. This paper describes how Hales&apos; method of profile interpretation is modified to overcome the assumptions of increasing velocity and layer thickness with depth when only first arrival data is available. A further expansion of Hales&apos; method enables presentation of refraction data in a form whereby bedrock features, such as changes in velocity, relief and dip in particular, are more readily recognized. Characteristic curves of the more common bedrock features are presented as an aid to bedrock feature recognition.

Jan 1, 1979

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By O. Lietard, J. Yvon, R. Mercier, J. F. Delon, J. M. Cases

INTRODUCTION Fineness is one of the main characteristics of powders and this parameter is the object of several definitions based on criteria connected with their uses as well as their determination methods. In trying to obtain the best reaction surface, fineness is characterized by the determination of the specific surface, but in other cases, particle size analysis is used. These two main methods are not, in fact, entirely independent and their complementary nature provides information concerning the morphology of the particles. In the case of a product formed by isodimensional spheres, the relationship between the specific surface and the diameter is well known: [S = 6 spd] where p is the specific weight of the material and d the diameter of the spheres. With no monodimensional spheres, but rather a granulometric distribution whose occurrences follow a mathematical law (1), the relationship is more complicated. The relationship between the specific surface measured by gas adsorption and the data of the particle size analysis is much more difficult to predict in the case of asymmetric porous particles, whose particle size distribution curves do not correspond to a known statistical law.

Jan 1, 1980