Search Documents

By William Kent

I DESIRE to place on record in our Transactions a recent innovation in blast-furnace practice, namely, the introduction at the Lucy Furnaces, in Pittsburgh, of four water-tube steam-boilers, of the Babcock and Wilcox pattern, aggregating 832 horse-power, builder's rating, or 9,568 square feet of heating-surface, utilizing the waste gases of the furnaces as fuel. The boilers are set in two batteries, each of 416 horse-power, and each battery occupying a ground-space of 22 feet 7 inches by 20 feet 4 inches. The accompanying dram-

Jan 1, 1885

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"' is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By Rodney L. Stone, David S. Cahn

As part of an over-all laboratory and plant test program to determine mixing ad other techniques for a more economic use of bentonite as an iron ore pellet binder, a settling test for measuring the bentonite content within a pellet or a batch of pellets has been developed. Through this test, it has been shown that dry fracture load is directly proportional to bentonite content in batches of pellets, but inversely propor tional to bentonite content in individual pellets of the same batch. This apparent paradox is explained by a negative correlation between a pellet's size and its bentonite content and the fact that large pellets can withstand a higher fracture load than small pellets. In past attempts to characterize green and dry iron ore pellets, the authors found large variations in the results of strength tests on closely sized pellets from the same batch.' Reasons advanced for such variations in the quality of pellets in which the binder is bentonite were the presence of internal flaws and the nonuniform distribution of the binder. Even when resulting pellet strength is good, there is still the question of whether the same strength could have been attained through a more effective use of a smaller amount of bentonite. The authors' own and other studies 2-3 have pointed out the strong dependence of pellet strength on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship could serve as a guide for the development of better mixing techniques and the associated economy of

Jan 1, 1969

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By Henry Louis

THE work performed by the Royal Commission on Mining Subsidence is likely to prove of permanent value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions."

Jan 1, 1929

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Zay Jeffries

IT is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a. fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a fine-grained steel rail might have grains or cells 100 times larger than coarse-grained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable than the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of. metal for a specific use, the latter determination being more indicative of. the life of the metal part than the tensile test. A grain-size determination with a tensile test is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now.

Jan 12, 1915

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By J. L. Jernegan

IN the summer and fall of 1875, the author was present during a short smelting campaign at the Hall Valley works, and having had occasion to make a number of chemical analyses of the ores, fuel, and fluxes, deems that the results of the same, and also an account of the smelting operations, may be found of interest to members of the Institute. The mines and reduction works of the Hall Valley Silver-Lead Mining and Smelting Company (limited) are situated at Hall Valley, Park County, Colorado. The smelting works are located about half way from the mouth to the head of the above-named valley, and the mines high up on the mountains, near its head. The three principal mines of the company are the Whale, Leftwick, and Cold¬spring. They are all on different veins, running parallel to one another, with a general trend from southwest and northeast. The

Jan 1, 1877

By Ernest L. Ohle

The newly opened Hayden Creek lead mine represents a variation from the usual Southeast Missouri type. Galena mineralization occurs in sandy dolomite cementing a conglomerate of granite boulders and in cracks in the boulders. The conglomerate occurs at the base of the Bonneterre formation on the slopes of two buried pre-Cambrian knobs. IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast Missouri Lead Belt and of the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fred-ericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this area, an assemblage of granites and rhyolitic flow rocks was eroded to a mature topography. Sedimentation, beginning in the Upper Cambrian, filled in the valleys and gradually covered even the highest hills. The first formation deposited was the La-motte sandstone; it is successively overlain by the Bonneterre dolomite, the principal lead-prodbcing formation, then the Davis shale. the Derby-Doerun limestone, and a succession of Cambro-Ordovician cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Frederick-town area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over 175 ft high.

Jan 1, 1953

By Ernest L. Ohle

The newly opened Hayden Creek lead mine represents a variation from the usual Southeast Missouri type. Galena mineralization occurs in sandy dolomite cementing a conglomerate of granite boulders and in cracks in the boulders. The conglomerate occurs at the base of the Bonneterre formation on the slopes of two buried pre-Cambrian knobs. IN 1943 diamond drilling from the surface in an area 2 miles southwest of Leadwood, Mo., discovered a lead deposit of a markedly different character from the usual southeast Missouri type. Subsequent drilling of about 500 holes indicated several million tons of ore, and in 1950 a 701-ft vertical shaft was sunk into the orebody. This paper describes the geology of this interesting occurrence insofar as it is known from the drilling and the small underground exposure at the bottom of the shaft. Geology The location of the Southeast Missouri Lead Belt and of the Hayden Creek property are shown in Fig. 1. As shown here, there are two separate producing areas, one from which the larger tonnage has come, located near Bonne Terre, Flat River, Desloge, and Leadwood, and the other to the south around Fred-ericktown and including famous old Mine LaMotte. The best published description of Lead Belt geology is by Tarr.* In pre-Cambrian time in this area, an assemblage of granites and rhyolitic flow rocks was eroded to a mature topography. Sedimentation, beginning in the Upper Cambrian, filled in the valleys and gradually covered even the highest hills. The first formation deposited was the La-motte sandstone; it is successively overlain by the Bonneterre dolomite, the principal lead-prodbcing formation, then the Davis shale. the Derby-Doerun limestone, and a succession of Cambro-Ordovician cherty dolomites. Several of these formations may be found in direct contact with the pre-Cambrian as their deposition progressively overlapped the older rocks on the flanks of the igneous knobs and ridges. Immediately overlying the pre-Cambrian there is, not uncommonly, a thin basal conglomerate of granite or porphyry boulders, which is incorporated into the overlying sediments. Deposition of the lower part of the rock section was fairly continuous, and the Lamotte sometimes grades almost imperceptibly into the lower sandy Bonneterre. Since the sediments were deposited on an uneven floor, they tend to reflect the irregularities in that floor. Most of the steep dips found in the district, that is, dips in excess of 10°, are original dips and not caused by deformation. Such domelike structures in the sedimentary rocks around the igneous knobs have localized a considerable number of the orebodies in the district and particularly those in the Frederick-town area. Many of the larger orebodies, however, have no close relation to the pre-Cambrian topography. Most of the lead production has come from the lower 150 ft of the Bonneterre formation, where disseminated ore spreads laterally parallel to the bedding for great distances. Average stoping height is about 20 ft, but in a few places there are stopes over 175 ft high.

Jan 1, 1953

By David H. Browne

The trite maxim that man is a tool-using animal might nowa-days be amended by saying that man is a tool-choosing animal. The chipped flint, at first all-sufficient, gave way to hammered bronze, and that, in turn, to wrought-iron and steel. As our knowledge of metals increases, we learn to specialize; we temper and anneal; we alloy and intermix; and we fashion for ourselves a metal suitable to our necessities. The knowledge of the properties and uses of the various metals and their alloys has become the capital of every constructive engineer, and the currency of every intelligent brass-founder aid blacksmith. Prom year to year, the specifications of the designer become more rigid, and the steel-maker is forced to study more closely the qualities obtainable by changing the treatment, or altering the composition, of his metal. Of making alloys there is no end. We have heard much, during the last decade, of manganese-steel and chrome-steel, of aluminum and tungsten, of titanium- and silicon- and copper-steels, and of every conceivable union into which steel could be coerced or cajoled. Without denying to each of these alloys novel and valuable properties, it. must be admitted that, of all alloys, the one which shows the greatest range of adaptability, and has met the largest measure of popular approval, is nickel-steel. Introduced to public notice by Mr. Riley, in 1889, its field of usefulness has been rapidly enlarged, until, at the present day, the use of nickel-steel is as thoroughly recognized as that of carbon- or manganese-steel. Concerning the properties of nickel-steel numerous articles have appeared in the technical journals. For the man in a hurry, who wishes to look up the properties and limitations of nickel-steel, these articles might almost as well be in the lost

Jan 1, 1900

By Clemens Jones

THE analytical history of phosphorus in its relation to the metallurgy of iron is an interesting study, the progress of which runs parallel with the development of the greatest industry in the world. Without the means of finding out how much phosphorus crude pigiron contained, the Bessemer steel process would have been impossible. To do this was originally tedious and slow work. On the other hand, the " direct" process of to-day, as well as the various special processes for steel or iron, have demanded the utmost rapidity in the operations of analytical chemistry. In general, any rapid process for the conversion of unrefined metal into a product of standard composition depends upon the rapidity of some accurate means employed to control it. Moreover, in our modern practice, it is not improbable that the differences in physical properties among the various makes of iron or steel are affected, if not produced, by the use of different methods of analysis. Recourse is always had for correction to the ((standard methods," but I incline to think that these methods are susceptible to error. It is very certain that the system of duplicates would not be resorted to, if the fact were otherwise. Even when duplicated, under the most careful and skilful manipulation, these standard methods produce disagreements. In proof of statements like these, which may sound. heretical, I hope, further on, to cite some evidence worthy of attention. I do not now mean to lay claim to the distinction of discovering the ultimate corrective. That result will come, no doubt, in. time, as the product of the experience of many workers. In the case of phosphorus, as of the other ingredients of iron or steel, a great deal has been done to accommodate the methods of analysis in rogue to the growing necessity for more rapid procedures: Much of this work has concerned what might be called the incidents of method. There is no better example of the accumulation of these incidental improvements than the work done on phosphorus; and I

Jan 1, 1890

By R. P. Carreker, R. W. Guard

True stress-true strain data are given for nominally pure molybdenum (99.95 pct) over the temperature range -196° to 1540°C (0.027 to 0.63 T/T). Strain rate sensitivity was determined by rate change tests and stress relaxation tests. Inhomogeneous yielding and strain aging effects were observed. The yield stress and tensile strength depend markedly on temperature below 400°C and are insensitive to temperature in the range 400' to 800°C. The ductile to brittle transition range is +25O to -25OC. Strain rate sensitivity and stress relaxation effects are very large near room temperature. THIS report presents data which were obtained as a part of a continuing program designed to document the deformation behavior of nominally pure metals over a wide temperature range.'" This research program is rooted in the conviction that sufficient tensile and creep data of appropriate quality and detail does not exist to provide precise phe-nomenological descriptions of the deformation behavior of pure metals as a function of temperature, strain rate, and grain size. Such knowledge is needed to provide a firm base for alloy design and an experimental framework to which theories of deformation must conform. These data also complement a parallel exploratory program investigating the properties of refractory metals, including molybdenum, and their alloys. Several important reviews and research reports dealing with the tensile properties of molybdenum as a function of temperature have appeared."-lo To a great extent the work to be reported in the present paper parallels that of Bechtold and of Pugh. The authors' results are in general agreement with those of Bechtold and Pugh. The principle differences be- tween the present experiments and those published previously are as follows: 1—Wire specimens prepared from arc cast molybdenum were used in the present experiments, bar specimens were used by others. Pugh used arc cast material while Bechtold's most extensive results" were obtained on powder metallurgy specimens. 2—Several different grain sizes were tested in the present experiments. 3—The testing range was extended to cover from -196°C to 1570°C (0.027 to 0.63 T/Tm). 4—The combination of wire specimens, high speed autographic recording, and a stiff testing machine permitted more detailed study of initial yielding. The principle contribution of the present paper is the demonstration of the relatively consistent mechanical properties of nominally pure arc cast molybdenum specimens of differing metallurgical history. Bechtold and Scotts have shown that arc cast and powder metallurgy molybdenum samples have comparable tensile properties in the range —75" to 200°C when processed to have the same re-crystallized grain size. Material The molybdenum used in this investigation was supplied by the Climax Molybdenum CO. Its metallurgical history is outlined in Table I; the final products were 0,030 in, diam wire specimens annealed at 1100' and 1375°C and 0.060 in. diam wire

Jan 1, 1957

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981