Search Documents

By R. W. Nelson

The theoretical basis is presented for energy dissipation methods of measuring permeability in saturated heterogeneous media. Analysis starts with the equation for single-phase flow in heterogeneous porous media which is a first-order partial differential equation in the unknown permeability. This equation is reduced to a system of characteristic equations useful in deriving a differential expression for the permeability as a function of the known potential distribution. For steady flow systems the expression is integrable, giving the permeability integral for direct calculation of the distribution along successive streamlines. The boundary condition in permeability is presented and includes a discussion of the special requirement to assure uniqueness. Theoretical results and necessary computations are incorporated into two general computer programs capable of determining the permeability distribution in two- and three-dimensional steady flow systems. Results are then presented for an energy dissipation analysis using the methods and soltware to determine a field permeability thickness distribution. INTRODUCTION Theoretical work leading to the description of fluid flow in heterogeneous porous media has developed slowly and somewhat sporadically, although the areas of engineering applications predominantly involve flow in nonhomogeneous media. The lack of accurate and economical methods for measuring field permeability distributions has been a major limitation to realistic description of natural flow systems. The economical measurement of permeability using energy dissipation methods may overcome this limitation. Among other things, any permeability measurement method involves consideration of energy dissipation; as used here, "energy dissipation method" denotes the following general approach. The areal energy distribution is measured on an existing flow system in porous media. Then through appropriate analysis of the dissipation of energy in the flow system, the permeability distribution is determined throughout the region using the minimum boundary conditions required to assure a mathematically unique result. This paper presents the theoretical basis for such a method, as well as the techniques and computer software needed to carry out the analysis. The method and techniques are then used in a preliminary field application. EQUATIONS DESCRIBING FLOW IN HETEROGENEOUS MEDLA Heterogeneous as used here implies differing in kind, having unlike quantities or possessing different characteristics. Accordingly, a heterogeneous porous medium has unlike quantities or differing characteristics at different locations. More precisely, if a porous medium is heterogeneous with respect to some property, then that property is functionally dependent on the spatial location. (Media properties are considered here as macroscopic.) Specifically considering permeability k,** then k = G(x, y, z) ,............(1) or the permeability is a scalar function G of the location (x, y, z). Spatial variation of several other properties, of which porosity, dispersivity and medium compressibility are but a few, is implied by the broad title of heterogeneous porous media. The term will be used hereafter to imply only heterogeneity with respect to permeability. The porous medium is considered isotropic as implied by G being only a scalar function. Anisotropy

Jan 1, 1969

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1'2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described' as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918

By Foster Fraas

Most commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.' As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions —those in region C designated as "deflected" or"deflectant"and those in region B designated as "residue." When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in series, and some practical machines use as many as I2. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, or both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1943

By Foster Fraas

Most commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.' As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions —those in region C designated as "deflected" or"deflectant"and those in region B designated as "residue." When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in series, and some practical machines use as many as I2. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, or both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1943

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

U.S. Signs Pact With Miami Copper Miami Copper Co., of Arizona has agreed to mine lowgrade copper ores in an extension of its Globe-Miami mining district operations at a guaranteed price of 27.35[] per lb, under a contract signed with defense Materials Procurement Agency. Terms of the contract call for delivery of 230 million lb of refined copper between 1955 and 1962. DMPA said highgrade ore in the de posit will soon be exhausted and it is considered advisable to have Miami continue the operation. The Government has an option to buy 120 million lb of refined copper from present production at market prices. Miami will develop the new ore- body at its own expense-estimated at $3 million. If losses under the new contract reach a specified point, Miami may cancel the agreement. The company plans to use the block caving method in the underground operation.

Jan 4, 1953

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By M. Cepak, K. Donovan, W. G. Pariseau

This paper examines the difficulties of applying the finite element (FE) method of analysis to quantitative design of cable bolt systems. Cable bolt systems are in general use for ground control in VCR (Vertical Crater Retreat) topes throughout the world. However, despite their widespread use and importance, design of cable bolt systems is highly subjective. Two difficulties with the FE approach are examined: (i) the use of standard elements with a high aspect ratio (slender elements) to represent bolts, and (ii) the influence of cable bolts on hanging wall stability of a VCR study stope. Analysis results indicate that the use of slender elements for bolts is practical in large scale finite element analyses of VCR stopes. There are significant advantages in this approach to the engineering design of cable bolt systems in underground mining.

Jan 1, 1984

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 12, 1979

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By Clarence E. Jackson, George G. Luther

THE ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepared with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. a, the angle at maximum load in four cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By Clarence E. Jackson, George G. Luther

The ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepaxed with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. 2, the angle at maximum load in lour cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By John E. Dowis

Ore distribution being what it is, many of today's mining companies are forced to develop foreign reserves to satisfy the demands of their customers. This necessity complicates the economic picture for a company, because management must look well be- yond grade and tonnage to determine the feasibility of developing a foreign orebody. Above all, the taxes on such a development must be assessed. The difference that taxes can make in mining profits will be illustrated here for three countries-Canada, Mexico and the United States. For purposes of comparison, identical orebodies will be assumed to occur in all three countries. Only the taxes on these properties will vary. Grade, tonnage, gross income, production costs and production rates will all be the same. The discussion will be limited to federal taxes, because state and provincial taxes are usually negligible by comparison. Assumptions relative to the orebody and the nature of the company undertaking the operation are as follows: (1) Copper is the only value to be recovered. (2) Sixty million tons of ore have been delineated. (3) Underground mining is required, and the production rate will be 3 million tpy. (4) The life of the property is 20 yr. (5) Operations in Mexico or Canada will be handled by a subsidiary of a U.S. parent company. (6) The subsidiary will offer stock.

Jan 1, 1970

By E. H. Dix

The work of Merical and other investigators indicates that the phenomenon of age-hardening in alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum Company of America to determine the functions * Metallurgist, Aluminum Research Laboratories. f Metallurgical Division, Aluminum Research Laboratories. Formerly with Metallurgical Division, Aluminum Research Laboratories. 1 P. D. Merica, It. G. Waltenberg and H. Scott: Heat Treatment of Duralumin. U. S. Bur. Stds. Sn. Paper 347 (1910). 2 M. Gayler: Constitution and Age-Hardening of Alloys of Aluminum with Copper, Magnesium, and Silicon in the Solid State. Jnl. Inst. Met. (1922) 28, 213. W. Fraenkel: Vergutbare Aluminiumlegiengen. Ztsch. Melallkunde. (1920) 12, 427. E. H. Dix, Jr.: Note on the Microstructure of Aluminum-Iron Alloys of High Purity. Proc. Amer. Soc. Test. Mat. (1925) 26, Pt. 2, 120. E. H. Dix, Jr. and H. H. Richardson: Equilibrium Relations in Aluminum-copper Alloys of High Purity. Trans. A. I. M. E. (1926) 73, 560. E. H. Dix, Jr. and W. D. Keith: Equilibrium Relations in Aluminum-manganese Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1927) 315. E. H. Dix, Jr. and A. C. Heath, Jr.: Equilibrium Relations in Aluminum-silicon and Aluminum-iron-silicon Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1928) 164. E. H. Dix, Jr. and F. Keller: Equilibrium Itelations in Aluminum-magnesium Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1920) 351. E. H. Dix, Jr., F. Keller and R. W. Graham: Equilibrium Relations of Aluminum-magnesium Silicide Alloys of High Purity. Trans. A. I. M. E., Inst. Met. Div. (1931) 404. W. L. Fink and K. R. Van Horn: Constituents of Aluminum-iron-silicon Alloys. Trans. A. I. M. E., Inst. Met. Div. (1931) 383.

Jan 1, 1932

By L. Bruce McRae

A programme of work was initiated so that the possibility for the agglomeration of Transvaal chromite-fines by pelletization could be investigated. The use of cementitious binders did not yield promising results, binder additions of up to 10 per cent failing to produce an agglomerate that would be suitable as feed for an electric-smelting furnace. Further laboratory and pilot-plant studies showed that high-quality pellets could be made from chromite bonded with small amounts of bentonite and hardened by heat treatment at temperatures of the order of 1000°C. An investigation was also done into the reduction behaviour of pellets containing amounts of stoichiometric carbon up to that required for complete reduction. The results showed that the maximum degree of reduction that could be obtained was approximately 75 per cent, and that these pellets had the physical properties that would make them amenable to smelting in a submerged-arc electric-smelting furnace.

Jan 1, 1977

By C. S. Trewin

Zinc, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be dctcrmined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent, lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. Rolled Zinc Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. ROLLED ZINC Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

Jan 1, 1928

By Wilber Stout

In Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson CO. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steuben-ville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the state. Small quantities of coke were made from the Upper Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co., but the operations were not successful and were soon abandoned. These failures and indifferent successes are not to be attributed to a lack of demand for a first-class coke, as Ohio has held a commanding place for many years in iron smelting; nor to a deficiency of coals, as the state has a vast reserve of such material. They are to be ascribed to the inferior quality of the native products offered to the trade. The cokes

Jan 1, 1920