Search Documents

By Ole Singstad

The legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer. After preliminary investigation it was decided to build the tunnel from Canal St., New York, to 12th St., Jersey City, which is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels—one for west-bound traffic and one for east-bound—the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear head room of 13 ft. 6 in. The tunnels have an exterior diameter of 29 ft. 6 in. The interior lining is of concrete, the sidewalls, tiled with a vitreous white tile, and the roadways are paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. Basis of Ventilation It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character. There have been vehicular tunnels built in Europe, principally in London, but they are shorter and have a smaller traffic capacity. Up to the present time, at least, they have handled a very large percentage of horsedrawn vehicles so that the necessary ventilation has been provided for by the natural draft through the portals and open shafts. Within the last few years, however, a small mechanical ventilating plant has been installed in the Blackwall Tunnel, which has been in operation about 27 years. I might mention that at the time this work was started, it was considered by many that the problem of ventilation was insuperable and it

Jan 1, 1927

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By A. N. Holden

A DISLOCATION mechanism has been described by Cottrell' by which metals can yield locally, I. form Liiders bands, giving rise to a characteristic stress-strain curve with a sharp yield point and appreciable strain at constant or decreasing stress. It is undoubtedly the best mechanism that has been suggested to date." In its present development, however, the dislocation mechanism provides a more satisfying explanation for the sharp yield point than for the extensive localized flow occurring at the lower yield stress. The primary objective in this paper is to extend the dislocation mechanism to account for localized cataclysmic flow by a dislocation collision process and to give experimental evidence to support such a process. Only the yielding of iron containing carbon -will be discussed, although other metal-solute systems are known to behave similarly. Cottrell Mechanism In brief, Cottrell explains the yield point in the following way: The dislocations in iron which must propagate to produce slip usually lie at the center of local concentrations of carbon atoms, since segregation about these dislocatlons relieves some of the local stress resulting from them. A dislocation surrounded by a "cloud" of carbon atoms is thus anchored, and a higher stress is required to set it in motion than to move a free dislocation. Considering all available dislocatlons to be anchored in this fashion, the iron exhibits a yield point when the first dialocations break free and move through the lattice causing slip. This first breaking away of a dislocation enables other dislocations to break loose by "interaction" and the process becomes a cataclysm producing local deformation or Luders bands. The yield point in the stress-strain diagram for iron is absent in freshly deformed material, but returns gradually with time; the phenomenon is one aspect of what is called strain aging. The rate at which the yield point returns following straining depends on the temperature of aging. According to Cottrell the rate of return of the yield point in strained iron is limited by the rate of diffusion of carbon at the aging temperature, the mechanism is onr: of reforming the solute atmospheres around carbon-free dislocations that had stopped moving coincident with the removal of stress. If the specimen is retested immediately after straining and unloading, carbon will not have had time to diffuse to, and re-anchor, dislocations and the yield point will not occur. The carbon diffusion limitation for the rate of strain aging apparently applies if the criterion for strain aging is either the change in hardness" or the change in electrical resistance" of the strained speci- men with aging time. The possibility exists, however, that the yield point actually returns to strained iron at some rate other than that deduced from hardness or electrical resistance data. Therefore, as a preliminary experiment, the rate of yield point return in a rimmed sheet steel strained 6 pct in tension was measured at 27°, 77°, and 100°C. A plot of yield-point elongation for each of these temperatures against aging time appears in Fig. 1. The aging process is described by curves which rise to a plateau value of elongation that seems independent of temperature, but at a rate that depends on temperature. Very long times lead to a further rise in the yield-point elongation above the plateau value. However, if the later increase in yield-point elongation is ignored and the log of the time to reach half the plateau value of elongation is plotted against 1/T, a straight line results for which an activation energy of about 25 kcal pel- mol may be assigned. Within the accuracy of this sort of experiment this is approximately the activation energy for the diffusion of carbon in iron (20 kcal per mol), and the carbon diffusion limitation suggested for the yield-point return on strain aging is valid. The Cottrell mechanism thus explains in a qualitative manner the occurrence of a yield point in iron and its return with strain aging. It fails, however, to explain some of the other experimental observations that have been made of the yielding behavior of iron. For example, it is known that the yield point in iron becomes less pronounced with increasing grain size. Annealed single crystals of iron have very small yield-point elongations .if indeed they have any,' compared to a polycrystalline steel. If the only requirement for a yield point is that the dislocations in the lattice of the annealed. material be anchored by carbon atoms, the difference in the behavior of single crystals and polycrystals is not explained. That a dislocation mechanism may be entirely consistent with little or no yield point in an annealed single crystal will become apparent later when dislocation interaction is discussed. Strain aging produces a definite yield point even in single crystals. This accentuation of the yield-point phenomenon in single crystals after strain

Jan 1, 1953

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By A.J. PHILLIPS, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Win. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm.. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four, binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for-examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By M. D. Hassiaslis

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1-The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2-The orientation of the chemical units at the surface; and 3-The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element-the mobility of the collector units in the two dimensions of the solid-liquid interface.

Jan 11, 1951

By Russell B. Cornell, William B. Plank

AT the close of the academic year 1940-'41 the largest number of students ever recorded received their first or bachelor degree in the mineral technology schools of the United States. The total of men thus prepared to enter their professional careers in the mineral industries was 1601, a number nearly 12 per cent larger than two years ago and nearly 75 per cent larger than four years ago. Notwithstanding this increase in the number of graduates and as had been predicted in the preliminary report in February, there was a slight decrease in the total student population of the schools in both the United States and Canada. During the college year 1940-'41, 9133 students were enrolled in the 54 schools of the United States and 764 in six of the seven schools of Canada.

Jan 1, 1941

By R. A. Wagstaff

Many changes in equipment have had to be made to handle the flotation products at the blast furnace, and these changes have meant an expenditure of considerable money, which has not been compensated by an increase in smelting tonnage. To date, very few new lead mines have been developed, so that the help derived by the innovation of flotation has been directed to old producing properties, where the ratio of concentration is greater now than when gravity concentration was in effect. In some smelting plants there has been an abandonment of complete units due to the introduction of flotation. Flotation Products Difficult to Handle The physical characteristics of the flotation product do not make for economic handling for lead blast-furnace work, either mechanically or metallurgically. The millman or miner do not know what trials and tribulations they have passed on to the smelterman. To the smelterman it is "the everchanging flotation," for little does he know what new reagent will be perfected tomorrow that may completely change the grade and physical characteristics of the product. Even the mining companies who have complete units of mining, milling and smelting have had a hard time to reconcile themselves to the fact that the unit cost per ton of ore smelted must go up with the increase of flotation product on the blast-furnace charge. The "smelterman's burden," for that is what flotation has been for the last few years, has not caused the smelter operator to lag or fall down, but has spurred him on with new zeal. The physical properties of the flotation products are as follows: (1) High moisture content; (2) mucky nature of product; (3) fineness of product, and (4) high metal content. New Mechanical Devices for Handling Furnace Product These characteristics have caused the use of many new mechanical devices in smelting practice, for example: New transportation equipment, such as solid-bottom cars, is required; unloading equipment and sampling

Jan 1, 1928

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 ('other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

This fund was established in 1929 for support of research and especially refers to non-ferrous mining and metallurgy. It is administered under the Board by a committee consisting of the President and Secretary and three members selected by the Board. HOWE MEMORIAL LECTURE The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectarers for the years indicated: Albert Sauveur—1924 Bradley Stoughton—1927 John A. Mathews—1925 Henry D. Hibbard—1928 William Campbell—1926 John Howe Hall.—1929 JOINT ACTIVITIES The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers, and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Society This is a corporation organized by the American Institute of Mining Engineers, American Society of Mechanical Engineers, and the American lnstitute of Electrical Engineers, to hold the title and administer the property at 29 West 39th St. In 1916, the American Society of Civil Engineers was admitted, and each society now has an equal one-fourth interest in the ownership, occupancy, and administration of the building. . The cost of this property has been over two million dollars. A. I. M. E. representatives are: Arthur S. Dwight, John V. N. Dorr and H. A. Guess. Alfred U. Flinn, Secretary, 29 West 39th St., New York City. Engineering Foundation This is a fund established by the United Engineering Society in 1915 with a gift of $200,000 from Ambrose Swasey. Subsequent gifts had increased the fund to about $620,000 on March 1, 1929. The income of the fund is used to further research in science and engineering and to advance the profession of engineering and the good of mankind. A research project in alloys of iron is being conducted in

Jan 1, 1929

By E. D. Leavitt

I desire to state briefly my views respecting the great practical value of the Watertown testing-machine, and the necessity that exists, for an able permanent commission to supervise its operations, in order that the results of all tests made thereon may be properly worked out and rendered available for public use. It is doubtless known to the Institute that this machine has, for the past two years, been placed at the service of the public upon payment of a per diem charge. It was my privilege to be among the first to use the testing-machine, and the results of my first experiments were of such importance, owing to the great capacity and extreme accuracy of the machine, that it has since become my practice to have tests of all materials used in constructions that came under my charge, made at Watertown. As a conseqnence, nearly one hundred tests have been made on my account directly, and some two hundred and forty additional for work built from my designs. It may be confidently affirmed, that the factor of anxiety on all these structures is exceedingly small .m far as the quality of material is concerned, and it is undoubtedly a very great advantage for parties interested in construction to have

Jan 1, 1882

By Walter Lee Brown

One of the characteristic steps in the march of modern scientific progress is the substitution of improved time-saving and labor-saving appliances for the antiquated and, in most cases, inconvenient forms of chemical and physical apparatus used by the earlier experimenters. This fact is strongly impressed upon us when we consider the question of the employment of illuminating-gas as a source of light, heat and power. Concerning its value as a light-producer, let the record of the past three-quarters of a century speak for itself. As a factor for power, we have evidence of its efficiency in the shape of the gas-engine. But its adaptability as a medium of heat, is the feature to which I wish to call attention, and in a special direction, viz., the assaying of ores. Gas assay-furnaces have been known and used for some years, but not to any very great extent, in this country at least. Therefore no apology on my part is required for the description I now give of a complete gas assaying-plant. The illustration accompanying this paper is a faithful representation of the group, as it was designed by, and arranged for myself, and appears in actual running order in my laboratory to-day. Its duty is to do roasting, crucible-fusion, scorification and cupellation. The furnace at the left is for roasting sulphurets or other ores for experimentation or actual work. It is what is known as a Fletcher No. 163, and consists of a fire-clay body strapped with sheet-iron bands, and a burner (No. 16, Fletcher). The opening at the top

Jan 1, 1885

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process. developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description OF Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1949

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By E. C. Houston

THE presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A 7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. DESCRIPTION OF PROCESS Metallic magnesium is produced electrolytically by the Dow and the Elektron

Jan 1, 1945

By John Tabor, R. B. Spivey

INTRODUCTION Shafts have been sunk in a number of ways. By and large, however, most have been sunk by drill, blast, muck, and slip form methods. Most methods have provided satisfactory means of completion. The major drawbacks to the conventional methods have been: (1) un- reliable cost estimates for completion; (2) unreliable rates of progress; and (3) unreliable integrity of the shaft lining. Recently , engineering design studies have been done that strongly indicate, that, by the use of existing proven technology, shafts can be completed faster, more cheaply, safer, and with a better lining that has been possible using conventional methods. THE METHOD The alternate method utilizes the techniques of big hole drilling, shield excavator tunnelling, and pre-cast concrete lining. Big Hole Drilling - Drilled shafts have been completed for several years and I don't intend to address the technology, only to point out the use of drilled shafts is an alternate method of shaft sinking. Ideally, in a multi-shaft mine, the first shaft would be blind bored and cased to a size, whereby it can handle the muck from the excavation of subsequent shafts. It should be an 8' to 10' completed diameter. The cost of such a shaft in sedimentary formations compares favorably with a conventional shaft. However, it is much faster. For additional shafts, the role of the drill is to complete small holes (3' to 4') to the desired horizon. This is merely a hole to allow slashing to a larger size with easier muck removal from an underground drift connected to the previously drilled shaft. The smaller holes, just as the larger one, should be cased and grouted into place so as to assure a smooth open hole. SHIELD EXCAVATOR Theory and History - Tunnelling Shields have been in common use for several decades, and steam powered shields were used in England over 100 years ago. The purpose of the shield is to provide temporary ground support, protect personnel during operation, and to house the excavating equipment. The excavating equipment approach has varied from attempts at a continuous or semi-continuous boring machine, the tunnel mole, to a mechanical or hydraulic digging arm. The shield may or may not be an active digging element. If not active, the boring tool or cutter is advanced ahead of the shield to full diameter and then the shield is moved up to the cutter, or the shield advances along with the cutter. If active, the cutter opens a conical free face, and the shield is either jacked forward so that the leading edge spalls rock to the free face or poling plates are thrust forward to spall to the free face. In either approach, various methods of muck removal are incorporated into the shield. These may be gathering arms, conveyors, or with moles, hydraulic transport, where the cuttings are sufficiently fine. The efficiency of the muck removal system is critical as excavation is rapid and the system could easily become muck-bound. Application to Shaft Sinking- Technically, the use of a shield to sink vertical shafts is no different than a tunnelling operation. It is, in fact, less complex in most respects. Muck and water removal are difficult in a blind-driven shaft. However, where an underground opening is available for handling muck and water, rapid shield sinking is possible, using a pilot hole for muck and water to fall through and be removed from below. The Tabor Mining Shield is basically a caisson approach, whereby, the ground is only seen at the face or bottom. It does have hydraulic jacks to force it downward and has segmented cutting edges which allows forepoling ahead of the shield. The hydraulic excavator allows mining in the center of the face around the previously drilled hole with the forepoling segments slabbing to this free face. First, the drilled hole is cased and grouted. The machine is a tube with an excavator. The work cycle is as follows: (1) The casing and grout are cut at predetermined intervals by shaped charges. (2) The casing is crushed by the excavator, removed from the hole and hoisted to the surface. (3) The excavator then rips out a face around the hole by digging the formation in tension and breaking the pieces

Jan 1, 1982

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,' the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By Lennart Bergstedt, Olov Fägremo

Boliden Metall Aktiebolag, the prime base metal mining company of Sweden, treats some 10-10.9 t/y (11-12 stpy) of sulphide ore in nine concentrators. During the years considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low grade ores. The autogenous grinding technique was first studied within the company as early as 1945. Basic test work commenced during the early fifties, whereby the merits of pebble grinding could be evaluated. In parallel with the converting of the rod mill/ball mill grinding systems to rod mill/pebble mill systems, the development work concerning the feasibility of autogenous grinding went on resulting in the installation of a 8 6.7 x 2.1 m (8 22 x 7 ft.) cascade mill at the Vassbo lead mine in 1959. Long term tests at the Vassbo plant together with a number of pilot plant test involving low grade silicious ores and pyritic comples base metal ores successive led to a better understanding of the process of autogenous grinding. Before a two stage autogenous grinding system could be chosen for the expansion of the Aitik copper mine, a carefully planned survey concerning grinding characteristics and variances in the ore and flowsheet was undertaken. The expanded plant went on stream in 1972 and in the beginning of 1973 and since then has performed excellently.

Jan 1, 1979