Search Documents

By Robert P. Burrows

Discussion of the paper of R. P. Burrows, presented `at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2237 to 2245. EDWIN M. CHANCE, Wilkes-Barre, Pa.-I have been very much interested in the comprehensive and able discussion of the important topic of mine lighting just given by Mr. Burrows, especially as I know by common report Mr. Burrows' ability and his close touch with the development of the electric mine lamp, and its use in mines in connection with a portable electric lamp. It is regrettable that Mr: Burrows was not able to acquaint himself more closely with the cost of mine illumination, the actual cost, as produced by a portable light as carried by miners, whether a flame safety lamp or an open light. Had he been able to acquaint himself more closely with these data, he perhaps would not have arrived at some of the conclusions which he has presented to us in his paper. For example, we find Mr. Burrows advises that the open torch is by far the cheapest source of illumination, as produced by a portable light. I am very sure that is not the fact. The cost of miners' oil varies from about 25.c. a gallon to 90b. a gallon. The various States have passed laws from time to time rendering it mandatory that the miner shall use, whether he is willing or not, a so-called better or higher grade of burning oil. These laws have entailed the use of an oil so expensive that the use of the oil torch has become practically impossible, and the acetylene or carbide miners' lamp has largely taken its place. I have evolved a few figures showing the relative efficiency and usefulness of the open oil torch and the acetylene miners' lamp. For example, the acetylene miners' lamp consumes or burns 4 liters of acetylene per hour, or 0.14 cu. ft.; the oxygen consumed is 10 liters, or 0.35 cu. ft. per hour; air consumed, 50 liters, or 1.76 cu. ft. per hour; black-damp produced, 40 liters, or 1.41 cu. ft. per hour; air rendered extinctive to the acetylene flame, 112 liters, or 3.95 cu. ft. per hour; carbide con- sumed, 13 g. per hour. The open oil torch, on the other hand, burns about 20 g. of oil per hour; the oxygen consumed is 48 liters, or 1.69 cu. ft. per. hour; air consumed, 240 liters, or 8.47 cu. ft. per hour; blackdamp produced, 191 liters, or 6.73 cu. ft. per hour; air rendered extinctive to oil flame is 1,413 liters, or 49.92 cu. ft. per hour.

Jan 5, 1916

By J. A. Pusateri, M. A. Orehoski, N. R. Arant

Plant studies on commercial-size ingots and laboratory experiments with induction furnace heats have demonstrated that the major source of ingot cracks is associated with two conditions arising during top-pouring practice: 1—solidification during pouring, and 2—turbulence created by the impact of the stream. Methods of controlling the two factors were effective in eliminating or significantly reducing ingot cracks. BECAUSE the process of removing surface defects from hot-rolled product is so costly, the steel industry is striving constantly to develop methods of preventing, or at least decreasing, the occurrence of surface defects. Investigations have revealed steel-making and processing variables related to major surface defects, and controlling these variables has led to improvements in surface quality. However, the fundamental causes of major surface defects, such as ingot cracks, have not been determined; consequently such defects persist. At the Research and Development Laboratory of the United States Steel Corp. in Pittsburgh, a seam research program was initiated to determine the fundamental causes of certain major defects. As a part of the program, ingot cracks in killed, finegrained C1020 steel were selected for study. A cost survey indicated that, of the steels produced in sizable tonnages, carbon steels in the range of 0.18 to 0.23 pct C content require the most conditioning. Since this is particularly true of C1020, any im-provement of surface quality that might be effected from the study would be beneficial. Also, since the frequency of ingot cracks is exceedingly high for this grade, the steel would provide an excellent opportunity for a thorough study of the ingot-crack-ing problem. Why steels in this carbon range tend to exhibit more ingot cracks than do other steels was not considered in the investigation; the mechanism of ingot-crack formation was of paramount importance. Also, only the top-pouring practice was considered in the investigation, because this pouring procedure is used more extensively than others. In this study, ingot cracks are defined. as deep surface defects that sometimes are observed in an ingot prior to rolling but usually are observed during the initial stages of rolling on the primary mills. These defects may occur at any angle to the rolling direction but are most prominent in the transverse or nearly transverse direction. The appearance of ingot cracks on the rolled product varies with respect to their angle of formation and with the extent of rolling after their first occurrence. Ingot cracks are also termed "deep seams," "arrowheads," "irregular cracks," and "transverse cracks." Fig. 1 shows ingot cracks in a rolled bloom. This report summarizes: l—the exploratory investigation of commercial-size ingots; 2—the labor-atory investigations related to determining the source of ingot cracks and developing corrective methods; and 3—the plant evaluations of laboratory methods of decreasing ingot cracks. Exploration of lngot Cracks in Commercial Ingots Materials and Experimental Work: At the Du-quesne Works of the United States Steel Corp., five heats of killed, fine-grained C1020 steel were selected for the exploratory phase of the seam-research program. The heats were made by open-hearth practices that are considered most conducive to good surface quality. They were top-poured into 22x25 in. big-end-up hot-topped molds. One as-cast ingot and four other ingots rolled to the following cross-sectional sizes were set aside from each heat: 16x20 in.; 9 1/2x10 in.; 5x5 in.; and 2x2 in. The processing of the heats, from the time of charging in the open hearth furnaces to the end of the rolling operation on the primary mill, was observed carefully and recorded. The cast ingot and the four rolled ingots from each heat were examined for surface defects. The cast ingots were split longitudinally near the vertical center plane to expose the ingot structure beneath badly cracked regions. Also, a series of transverse sections was cut at about 1 in. intervals in a badly cracked area of one ingot. All sections were ground, polished, examined by sulphur printing and deep etching, and photographed. The rolled ingots

Jan 1, 1955

By Walter Remmers

THE fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather common knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusuable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown 1/8 in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration.

Jan 1, 1930

By Carleton Ellis

The problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific standpoint, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London ; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by may of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of

Jan 1, 1913

During the nineteen months in which our country was actively engaged in the war, the United States Shipping Board Emergency Fleet Corpn. expanded the shipbuilding capacity of the United States from an unimportant position among the world's producers of ocean-going tonnage to first place. At the same time it increased the overseas merchant fleet of the United States from a negligible quantity to second place. The shipbuilding program has been greatly reduced since the signing of the armistice. There have been suspended or canceled contracts for 754 ships aggregating 3,797,825 deadweight tons, which would have cost $797,564,276 to complete. The cost of canceling these contracts will be about $202,853,456, and the saving effected by cancelations will approximate $594,710,820.

Jan 7, 1919

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et&apos; al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4&apos;5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7&apos;8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

By E. Gilpin

The following notes may serve to bring before your Institute an idea of the iron-ore resources of Pictou County. Enough work has been done to permit an estimate to be formed of their quality and probable extent. As yet the systematic mining and smelting of ironore in Nora Scotia is confined to the operations of the Steel Company of Canada, in Colchester County. Although the locality I am about to describe appears, in many respects, well adapted to iron smelting, etc., no attempts have yet been made to begin work. Nora Scotian capital is more readily turned to lumbering, fishing, and shipping ventures; and such an investment appears equally foreign to the rest of the Dominion. I need not, however, go further into this part of the subject, and can only hope that my notes may prove serviceable as indicating a probable field for future development. The accompanying map shows the position of the harbor of Pictou relative to the coal and iron-ore fields, and to the railways which intersect them. The branch of the Intercolonial Railway, running from Truro to Pictou, forms the western boundary of the iron-ore district, which extends beyond the point where the New Glasgow and Cape Breton Railway crosses the French River. The iron-ore district may be roughly described as a triangle formed by the ore-outcrops and the two railways, the former making the base, and the latter the sides of the triangle, the apex resting on the coal-field at New Glasgow. The drainage of the country is toward the Gulf of St. Lawrence, through the Middle, East, Sutherland&apos;s, and French rivers; and the surface is undulatory, seldom exceeding two hundred feet above the sea-level, except in the district lying between Glengarry and the upper waters of the French and Sutherland&apos;s rivers, where a maximum height of about five hundred feet is reached at several points. Geologically speaking, the district embraces two divisions, the Carboniferous and the Silurian, the latter resting on strata provisionally considered to be of pre-Cambrian age. As no geological

Jan 1, 1886

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull&apos;s suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin&apos;s observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin&apos;s studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several &apos; strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r&apos; phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By Jim Douglas, H. H. Rachford, D. W. Peaceman

The problem of unsteady-state gas flow through porous media has been solved numerically only for the case of linear or radially symmetric reservoirs. A recently introduced numerical method for solving the unsteady-state heat flow equation in two dimensions is applied to the calculation of the depletion of a square region containing a perfect gas. Solutions are presented in graphical form for various values of dimensionless parameters. The solutions are compared with published .solutions for radial reservoirs. I NTR ODUCTION The problem of unsteady-state flow of gas through porous media gives rise to a second-order non-linear partial differential equation for which no analytical solution has been found. Numerical approximations to solutions of the gas flow problem have been obtained by the stepwise solution of an associated difference equation1,2. However, the methods so far developed have required that the reservoir be either linear or radially symmetric. This restriction in shape has been necessary so that only two independent variables be considered, namely, one distance variable and time. In order to deal with reservoirs having more realistic shapes, it is necessary to develop numerical procedures for the solution of the gas flow problem involving two distance variables. A numerical procedure, denoted as the alternating-direction implicit method, for the solution of the heat-flow problem in two dimensions has recently been introduced" By the use of this procedure, approximate solutions have been obtained for heat-flow problems in a square8, and in regions having various non-rectangular boundariesa. Because of the similarity between the equation for heat conduction in solids and the equation for gas flow in porous media, it is reasonable to expect that the alternating-direction implicit method should also be useful for solving the gas flow problem in various two-dimensional regions. Solutions have been calculated for the simplest two-dimensional region, a square reservoir with a single well in the center. While reservoirs of such simple geometry seldom, if ever, exist, the solution of this problem is of some practical importance because it is also the solution of another problem, that of determining the depletion history about an individual well in an infinite uniform reservoir containing wells spaced throughout on a square lattice and producing equally from each well. Finally, it is of interest to compare solutions for a square reservoir with those for a circular reservoir and to determine the effect of the shape of the boundary for that particular case. METHOD OF CALCULATION Basic Differential Equation By combining the equation of continuity, the perfect gas law,

Jan 1, 1956

By L. G. E. Bignell

Surveying what was done in 1929 in meeting problems of oil-field equipment corrosion, one is struck by the fact that fewer meetings were held for discussion of these problems and fewer papers written than in any year since the subject engaged the attention of petroleum engineers. This does not mean that progress has not been made, for a great deal actually has been accomplished. Recommendations that accompanied field reports have been put into actual trial and some results obtained are gratifying. The type of papers prepared also has undergone a change, for they now deal with things accomplished rather than recite damages and suggest possible remedies. Some of the most notable work pointing the way for future solution of many pipe line problems is that done for the U. S. Bureau of Standards by Dr. K. H. Logan and Dr. Gordon N. Scott, dealing with tests of pipe coatings and reports on soil conditions. Many facts of great importance have been isolated and defined by these two men, not only indicating what may be done in some instances to retard corrosion, but showing that things formerly considered of importance have little bearing apparently upon the practical results. All-aluminum Storage Tanks In April, 1928, an all-aluminum 500-bbl. field storage tank was put into actual field use in Crane County, Texas, together with another tank of the same capacity but made with steel bottom and lower section of side sheets and aluminum upper ring of side sheets and deck. In April, 1929, after a little over one year&apos;s use these tanks were opened and examined by a group of engineers and chemists. The results of the test were enlightening. Other tanks made entirely of steel and used in the same battery with the two test tanks had some of their side and bottom sheets destroyed by corrosion in six to nine months, but the all-aluminum tank was in actual use for 18 months before holes were found corroded through the bottom, when the tank was examined for a second time in September, 1929. This field test of the aluminum tank confirmed the already known

Jan 1, 1930

By D. S. Hutton, W. C. Leslie

Thermal etch patterns developed on poly crystalline 3.5 pct Si-Fe by heating in hydrogen or in argon have been examined. The most prominent feature of the etching is the development of striations on grains with (100) planes near the plane of the surface. These striations are probably produced by the resoution of a random, high-energy plane into (100) facets of lower energy. THE thermal etching of iron and iron-base alloys has a long history. The phenomenon was observed by Osmondl more than 70 years ago. The literature on thermal etching between that time and 1951 was reviewed by Olney,2 and a briefer review appeared in 1958. 3 The only articles which have been found dealing with the thermal etching of silicon iron are those of Dunn and Lionetti4 and of Dunn, Daniels, and Bolton,5 and they reported only grain boundary etching. EXPERIMENTAL PROCEDURES A cast 3.5 pet Si-Fe alloy was given a metallo-graphic polish and etch, then placed in flowing purified hydrogen for 6 hr at 2200°F. The same specimen was later repolished and etched to remove the thermal etching. The specimen was then held in flowing purified argon at 2200°F for 72 hr. In both instances the specimen was rapidly cooled by being pulled up quickly into the cold zone of the furnace. All photomicrographs shown are of the surface as removed from the furnace. Oblique illumination was essential for observation of the thermal-etching effects with a light microscope and was used for all the photomicrographs. RESULTS AND DISCUSSION Grain boundary etching, grain boundary movement, and contouring within grains are illustrated in Fig. 1. The contours within a single grain followed behind the advancing grain boundary. To determine the average contour interval, or step height, white light was used in an interference microscope. The steps were of the correct magnitude to separate while light into its spectrum of colors. A green light was focused at the top of a contoured area, shifting to red across the field. By using the difference in the dominant wave length of red and green light,6 and counting the number of steps across the area, it was possible to obtain a value of about 80A for the average step height. Laue back-reflection patterns of four grains with contour lines showed that the grains had a (100) plane slightly inclined to the plane of the surface (± 5 deg). Insofar as this could be determined from their irregular traces, the contour lines within a grain had a common direction, <100> ± 5 deg.

Jan 1, 1961

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.&apos; Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By T. Olrog

Dissemination of technical data on developments in rock-blasting techniques in Sweden initially takes place as personal contacts and contacts between companies. In addition to these informal contacts, contacts occur in Sweden in a somewhat more organized form. There exists an informal working group--the Rock Blasting Committee--which consists of a number of personal representatives from various companies that perform rock blasting on a large scale and from firms manufacturing the equipment that is used. This means that people from both mining and construction companies get together, plus the manufacturers of explosives, drill steel, drilling machines, and loading equipment. This working group has, so far, succeeded very well in ignoring the purely commercial interests of the companies concerned. Cooperation in this form was started in the 1940&apos;s when the tungsten-carbide drill steel was invented-the group originally concentrated entirely on the development of that product. Their activities have been broadened since that time and now a meeting is held every year, at which practical experiences are reported. Only in the past five years have subjects relating to blasting procedures to avoid rock damage been treated at such meetings. This, of course, does not mean that such techniques had been neglected previously. It does, however, reflect the fact that practice in this field is still under development. Why do we try to be careful about the rock surfaces? Obviously, it is a question of economic evaluation. An even rock surface provides, in certain cases, the conditions for more favorable maintainance costs later on, greater strength, and a diminished risk of slides. The economic connections in this field, however, are neither simple or clear. A well-controlled blasted rock surface limits the need for concrete when you later build the concrete constructions. In this respect, the connections are all the more clear. In certain situations, such as tunnels for hydroeletric power plants, a good rock surface that is not lined is hydraulically more favorable than a more coarsely blasted surface. This permits a gain in the height of fall, but the

Jan 1, 1970

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts&apos; Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts&apos; method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts&apos; law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,&apos;4, &apos;6 Fe-Cu,&apos;6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 &apos;77 187 19>2° Fe-Sn,16 and Fe-v.51 &apos;3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1983

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f&apos;racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,&apos; have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961