Search Documents

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By David Kramer, Cecil G. Rhodes

Critical transport currents were measured as a function of perpendicular external magnetic field in Ti-22 at. pct Nb wire samples. These samples were heat-treated to yield w Phase precipitates at denslties ranging from 10 to 10 17cm-3. The Precipitates are ellipsoids of revolution with major axes of 50 to 1300A. Flux-Pinning by w precipitates is responsible for the high critical transport currents that were ob- ThE ability of a type II superconductor to sustain a zero-resistance transport current (Jc) in an external magnetic field (H) is due to the presence of micro-structural features which can impede the motion of magnetic flux penetrating the superconductor under the influence of a Lorentz force. Such features are referred to as pinning sites. The pinning strength is tained. A sample cooled from 800°C and annealed 1 hr at 450°C carried a critical tramport current of 10 amp per sq cm at 30 kG. Variations in the current-carrying ability of this alloy are due to changes in its pinning strength which is a function of precipitate density and composition and of the composition of the matrix. the reaction of the bulk superconductor to the Lorentz force and depends on the efficiency of the individual pinning sites and on their volume density. The super -current density increases with pinning strength, other things being equal. The above concepts are discussed in detail in a comprehensive review by Livingston and Schadler.' In Ti-Nb alloys, as in other binary titanium alloys, the metastable hexagonal w phase usually forms below the p/a + p phase boundary near the titanium side of the phase diagram. Stiegler et a1.' have summarized much of what is known about w phase in titanium and zirconium binary alloys. The present work deals with

Jan 1, 1968

By W. A. Turcotte, A. D. Paananen

Introduction The large reserve of fine grained oxidized iron-formation at the Tilden mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Due to the nonmagnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden, ore body have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of desliming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions. Development of selective flocculation-desliming was a key to commercialization of the process. Operations started in late 1974 with Algoma Steel Corp. Ltd., J & L Steel Corp., The Steel Company of Canada Ltd., Wheeling-Pittsburgh Steel Corp., Sharon Steel Corp., and The Cleveland-Cliffs Iron Co. as participants. Cleveland-Cliffs operates and manages the operation. Development of the Tilden Flowsheet The geology and ore reserves of the Tilden mine have been detailed in a paper by Villar and Dawe (1975). A joint program was undertaken in 1961 with the US Bureau of Mines in Minneapolis using the flowsheet developed by the Bureau employing the selective flocculation-desliming and calcium activated anionic silica flotation method (Frommer, et al, 1966; Frommer, 1964; Frommer, Wasson, and Veith, 1973). During this time, parallel testing at Cleveland-Cliffs Research Laboratory and Pilot Plant centered on the same type of desliming but was followed by the cationic flotation of silica with amine collectors (Columbo and Jacobs. 1976). The cationic silica flotation system was eventually chosen for its overall efficiency and simplicity. Regardless of the flotation method chosen, the technique of selective flocculation-desliming prior to flotation is the key to the success of the process. The flowsheet is described in detail by Villar and Dawe (1975). [Figure 1] shows a simplified one-line flowsheet of the Tilden concentrator. A total tailings thickener has been added to the original flowsheet and was placed in operation in 1978. The total-tailings thickener overflow reports to the reuse water pond and the underflow is pumped approximately 8 km (5 miles) to a storage basin. A flowsheet of the reuse water system is shown in [Fig. 2]. Selective Flocculation-Desliming Data have been published on the mechanisms and factors affecting selective flocculation in iron oxide-silica systems. The intent of this paper is not to discuss the theoretical aspects of selective flocculation, but rather to present experience gained from the commercial Tilden operation and from bench and pilot plant testing of fine-grained oxidized iron ores. From the bench and pilot plant testing prior to plant startup, certain reagent combinations and rates for the commercial Tilden plant were established. In the experience gained from three years of plant operation at Tilden, some of these reagent dosage rates have required significant adjustments due to changes in reuse water quality and to meet the requirements of varying ore types. Reuse Water The process water quality is a major concern at the Tilden mine and is constantly being monitored for selected chemical and physical characteristics. This monitoring has continued on a regular basis in order to gain a more thorough understanding of the interactions taking place in a dynamic water system and particularly as water quality is influenced by seasonal variations. Control of the reuse water chemistry is essential to the Tilden process both in the selective flocculation-desliming and flotation stages of concentration. With roughly 75% of the reuse water used in grinding-desliming operations, it is readily apparent that the biggest "reagent" in the selective flocculation-desliming process is water. Not enough can be said about the close control that must be exercised on the overall reuse water system. Control of the chemical treatment of the feed to the total tailings thickener is of utmost importance in order to produce a reuse water for the concentrator that is compatible with all stages of the concentrating process. There are many analyses made which aid in judging the quality of the water. Some of these are shown in [Table 1]. Five are particularly important and are monitored daily so that reagent adjustments can be made as required: suspended solids, calcium hardness, pH, dissolved silica concentration and temperature.

Jan 1, 1981

By Edward Keller

THE ASSAY FOR COPPER. SOMEONE some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The. writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he :feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample 1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2, g. of copper) measured out for the electrolytic deposition; in the other Method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed -a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 8, 1913

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.'.' The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,' experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By M. Muskat, H. H. Evinger

ALTHOUGH the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.1 In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was. measured and an attempt was made to determine the effectiveness of 'sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to determine the effect of tamping were performed by Snelling and Hall,2 Small charges (20 grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.3 The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.5 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

By David C. N. Cockburn

INTRODUCTION This paper analyses certain of the financial considerations which will commonly apply in relation to the following questions: - what equity structure or project vehicle should be adopted for the exploration and/or exploitation of a project by more than one unrelated participant? - what vehicle should be adopted by a participant for its participation in a multiparty project? Due to local, politically motivated laws in certain jurisdictions, or due to the overriding requirements of a dominant participant, there may be little choice of the underlying multiparty structure which may be adopted for the exploration, appraisal and/or development phases of a project. Nevertheless, even in such circumstances, attention should be given, at least in the preparation of the related documentation, or in considering methods of participating or funding the project, to certain of the points discussed below. This discussion of financial considerations in the context of the more commonly adopted multiparty structures concentrates primarily on fiscal, financial accounting, financing and funding aspects. TYPES OF PROJECT VEHICLE FOR MULTIPARTY INTERESTS The well known types of vehicle adopted for the participation in a project by more than one participant (assuming that the participants are effectively unrelated) are as follows. Joint Venture (unincorporated joint venture) By far the most commonly adopted structure for mining ventures, a joint venture is usually defined and documented in terms to distinguish it from a partnership for important tax and legal reasons. In essence, this is a contractual association of more than one participant to carry out a specific commercial project or purpose. The relationship between the separate participants and their respective rights, interests, obligations and liabilities are agreed between the participants in one or more contracts (viz Joint Venture Agreements or Joint Operating Agreements together with ancillary documentation). Unlike other project vehicles of participation, in most jurisdictions there is no specific body of law governing joint ventures. The participants thus enjoy contractual freedom to negotiate whatever deal they may wish between themselves. Jointly-Owned Project Company (corporate joint venture) A very familiar vehicle, this is a separate and distinct legal and tax entity incorporated under the company laws of the place of incorporation to undertake specific objects, and granted specific powers, in relation to the Project. Although certain rights, interests and obligations may be circumscribed in the governing corporate instruments by the promoter participants, the corporation laws of the relevant place of incorporation, and the selection of such governing laws (assuming freedom of choice) and future political changes in such corporate laws, should be carefully considered. The use of a company in a multiparty structure may be peripheral to the project itself as a specific purpose vehicle (for example, a joint sales agent or marketing company or a joint borrowing vehicle) or it may form a central function such as in the case of a tolling company which will own the project for legal and taxation purposes and raise financing with the backing of the shareholder participants commonly by the adoption of take-off, throughput and/or user agreements. Partnership This is a legal relationship, subject to the often wide-sweeping restrictions of the relevant local partnership laws, under which the participants have agreed to carry on a business venture together with a view to profit. The effect of the relevant partnership laws, as well as the various types of partnerships and the

Jan 1, 1985

By L. R. Flint, W. L. Freyberger, W. J. Howarth

W. L. Freyberger (Director, Institute of Mineral Research, Michigan Technological University, Houghton, Mich.)-The authors are to be complimented on their theoretical analysis of a column flotation process, and the comment I wish to make is not related to that analysis, but to the use of the word "countercurrent" to describe that process. Strictly speaking, the process the authors have described is countercurrent only in the sense of particle-bubble contact. That is, as solid particles and air bubbles pass through the column, the leanest flotation feed (the tailing) comes in contact with the greatest concentration of mineral-free bubbles. However, air bubbles alone do not comprise the complete extracting phase in a flotation system. A second component of this extracting phase is the collector, which is really the extractant inducing transfer of mat-

Jan 1, 1972

By T. R. Ingraham

When aluminum sulfate was decomposed in an evacuated apparatus and the sample cooled, Q alumina was found. The thermodynamics of the decomposition reaction were resolved by measurements of the total pressure of SO3, SO2, and O2 generated over the sample at various temperatures. The results were correlated with other published data to calculate the rmges of thermodynamic stability of the various compounds involved. The thermal decomposition of aluminum sulfate was studied by Wijhler, Pluddeman, and Wöhler1 and by Warner and Ingraham.2 The results of both studies were critically reviewed by Kellogg,3 who observed that "each set of data shows considerable scatter and strong curvature on a plot of log pso3 vs 1/T".3 He agreed with Warner and Ingraham2 that both the discrepancy in the two sets of results and their curvature may arise from the indefinite properties of the particular form of A12O3 which is formed during the decomposition. While studying the thermal stability of other sulfate systems, we had noted the presence of nonequilibrium oxide properties in both the cobalt4 and manganese5 systems, but neither had shown any appreciable curvature on a logPSO, vs 1/T relationship, and the data from both systems agreed reasonably well with prior work. It therefore seemed reasonable to reexamine the technique which had been used in our earlier work on aluminum sulfate.2 The principal difference was that a tightly compacted pellet had been used for the earlier aluminum sulfate work, whereas a loose powder, contained in a platinum boat, was used for our work on other sulfate systems. In addition, a better technique had been developed for dehydrating the samples. From work done on the nickel system,6 we had become aware of the highly protective nature of some sulfate layers on their oxjdes, and hence of the necessity of providing a large surface area of P3e sample when equilibrium was to be attained in a reasonable time. That observation suggested that perhaps a steady state, rather than equilibrium, had been reached in the earlier work on aluminum sulfate. This paper reports a repetition of the experimental work with large, finely divided samples of anhydrous aluminum sulfate. APPARATUS AND PROCEDURE The apparatus used in the experimental work was described in earlier papers.2,7 The source material was Anachemia reagent-grade Al2(sO4)3 - 18H2O which was first partly dehydrated by heating at 400°C for 48 hr and then completely dehydrated by repeated baking of an aluminum sulfate-oleum slush to dryness at 450°C. ? Alas was prepared by decomposing some of the sulfate in a muffle furnace at 800° C overnight. Approximately equal amounts of the 7) alumina and aluminum sulfate were used in the experiments. The finely divided samples were handled under dry box conditions, and in addition some of the aluminum sulfate was decomposed in the apparatus while it was under vacuum, to ensure its complete dehydration prior to sealing the apparatus. The samples were heated to a series of constant temperatures on both increasing- and decreasing-tem-perature programs. Two to three days were required to obtain steady readings of the total decomposition pressure on an increasing-temperature program, and 5 to 6 days on a decreasing-temperature program. Three samples were examined on both programs. Within experimental error, the results for each sample and each program could not be distinguished.

Jan 1, 1969

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

By Blamey Stevens

(Butte Meeting, August, 1913.) THE following paper aims to make a full explanation of the phenomena of rock jointing: It may be unnecessary to give any general description of what are termed joints in rocks, but Professor Geikie's clear and faithful generalizations are so illuminating that no excuse need be given. for introducing the following and other quotations into this paper "Almost all rocks are traversed by vertical or highly inclined divisional planes termed joints. These have been regarded as due in some way to contraction during consolidation (fissures of retreat) ; and this is no doubt their origin in innumerable cases. But, on the other hand, their frequent regularity and persistence across materials of very varying texture suggest rather the effects of internal pressure and movement within the crust." 1 General Explanation.-In this paper I show that the phenomenon of jointing may to a large extent be accounted for by the pressure of the water contained in the pores of the rock. To understand this, each constituent grain of the porous material may be considered to be separately compressed by the water which submerges it. As all the grains are held together by cohesion, the whole mass is contracted by this pressure. In an indefinitely extended mass, however, there must be a limit to the possible contraction without rupture, because the material is restrained from moving freely by other material around its boundaries. The mass of rock thus becomes broken up. This phenomenon is known as '" shrinkage " jointing. The term " shrinkage " is an apt one, if it be understood that the shrinkage of the rock is often brought about by change of stress. Stresses.-The compressive component of water stress on the individual grains is evidently the same as that of the water with which it is in contact. This is so, both before and after the jointing is formed. Before the jointing is formed there is, however, a tensile stress in one or more directions which keeps the material from contracting. .

Jan 7, 1913

By DR. DOUGLAS

Discussion of the Paper of Dr. Douglas, presented at the Toronto Meeting of the Institute, July, 1907 (Trans., xxxviii., 455 to 471). EDGAR HALL, Silverspur, Queensland, Australia (communication to the Secretary*) :-Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the side of freedom among the younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms referred to have suffered by their secrecy is their own business-I. bold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to be proved conclusively by Dr. Douglas's own writings. In his paper on The Copper Situation,1 Dr. Douglas says "In comparing iron and copper mining, . . . it must be remembered that 2 tons of average iron ore from the most prolific source now available will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year's production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-ore would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Sep 1, 1908

Book Review MEXICO UNDER CARRANZA. By Thomas E. Gibbon, Los Angeles, California. Doubleday Page and Co., New York, 1919, 270 pp., 711/2 X 5 in. $1.50. A vivid, accurate, convincing summing up of the Mexican problem as it confronts us today, devoid of sensationalism or bigotry. A compelling narrative of the relations of the Carranza Government and our own from Oct. 15, 1915, when it was recognized as the de facto government of Mexico, to the present time. It shows the absolute lack of promises kept or lived up to either with its own people or the United States. This is not done by invective or the indiscriminate use of adjectives but by quoting from the instruments on record on both sides of the case. The driving of the Red Cross out of Mexico, which condemned many of the native peons to starvation, and the interference with the Pershing Punitive Expedition are merely mentioned, but the crying crime against the Mexican people, who have sunk to unbelievable depths of misery obscured, but not exceeded, by the sufferings in Europe, is held up in a clarified light. Two illuminating chapters are devoted to the character and treatment of foreign investments in Mexico, Which are a complete refutation of the common statement that Mexico has been exploited remorselessly by the foreign investor. The conces-sions given by Diaz in the days of his regime most condemned are nowise as large nor the land grants as extensive nor the title so absolute as those granted to the railroad builders of our own transcontinental systems and other of our nationally subsidized works. This is not left to further argument but is settled by quoting the various official instruments and not at all in a tedious way. The author's concluding chapter is a picture of the Mexican people from Aztec times, when they had reached a civilization which gave them a better calendar than the Roman Empire ever had until modern times, to their present unhappy and pitiful condition. He concludes, basing his findings on parallel historical downfalls of a once proud people, that present conditions are the natural result of the absolute domination of an alien minority. He grants, of course, that there are many estimable Latin-Mexicans of integrity, ability and charm, but maintains that the dominant minority has continually degraded in fulfillment of the sociological law that the sure revenge of the servile class is found in the corruption of the master class. The book is replete with historical and literary allusions which, added to the pleasing style of the accomplished author, make fascinating the account of one of the world's great tragedies. Mr. Gibbon is a lawyer who has spent much time in Mexico and shows an understanding of the native people not shared by all writers on the Mexican problem. A distinct addition to all literature on the subject. P. E. B.

Jan 8, 1919

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

Development: Iron Ore In Peru Utah Construction Co., of San Francisco and a Peruvian Government corporation have signed an agreement for development of a large iron orebody in Peru. Most tests show 60 pct iron or better. Most of the ore is magnetite. Although ore will be shipped mainly to Eastern U. S. blast furnaces, shipments to the West Coast may develop as the orebody opens up. The construction firm indicated three American steel companies have shown interest in the project. The orebody is located 300 miles south of Lima and about 15 miles from the coast at the same longitude as New York City. Allen D. Christensen, executive vice-president of Utah Construction noted that the distance is shorter between Peru and the East Coast. The ore deposit measures about four to five miles in one direction and 10 miles in the other. As many as 15 outcroppings within these limits have been reported. Several of the outcroppings are thousands of feet long by several hundred feet wide, Christensen said. Shipments between 100,000 and 200,000 tons of ore per month are projected by the company. Cost of opening the mine to production may go over $5 million, Christensen said. It would include building of docks for ocean going vessels, housing, and heavy duty mining and processing equipment. The contract with the Peruvian government gives Utah Construction six to eight months for additional tests and a 20 year concession for mining the orebody. Peru will collect royalties on all ore. The company will also supply about 300,000 tons per year for an electric furnace to be installed by the Peruvian Government at Chimbote. No steel is produced in Peru now. Utah Construction formed the Argonaut Mining Co. last year, and was shipping iron ore from British Columbia to Japan at a rate of more than 50,000 tons a month, before winter weather decreased operations.

Jan 1, 1952