Search Documents

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By Donivan L. Gordon, Fred H. Dorheim

Often, as viewed by the public and many in the mining industry, abandoned limestone and gypsum quarries offer a simple, economic solution to the twofold problem of solid-waste disposal and land reclamation. In a state where about 75% of the existing quarries are in hydrologic connection with carbonate aquifiers the rationale for considering the storage of solid waste in them must be critically examined. Consistent with the requirements of water resources protection, criteria are suggested to evaluate the potentiality of using abandoned limestone and gypsum quarries as sanitary landfill sites.

Jan 1, 1975

GENTLEMEN : Herewith are transmitted the reports of your Treasurer and the Chairmen of your standing committees on Admissions, Membership, Papers and Publications, and Library for the calendar year 1931. To these reports you are referred for further details of the year's activities. Finances.-Depressed industrial conditions prevailing throughout the year were reflected in a substantial decline in current revenue. Aside from interest on sundry special funds (but including that from the Life Membership, Library, and General Reserve Funds) total receipts amounted to $168,274, compared with $194,636 in 1930. The principal items of decrease were $17,000 in advertising income from the monthly magazine MINING AND METALLURGY, and about $9,600 in dues and initiation fees. Of this shrinkage $4,000 is accounted for by decrease in the number of new members enrolled; and $5,600 by diminished income from current dues and arrearages. This naturally has coincided with an \ increase in delinquency and "drops" or suspensions for nonpayment of dues. The decline in advertising income, amounting to 38 per cent as compared with that of 1930, in general paralleled the experience of all technical and trade publications; and it is problematical whether 1932 will show as large a return from advertising as did 1931.

Jan 1, 1932

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By Carl E. Williams

A computer program has been developed which will locate the economic limits of an open-pit mine and also designate which ore and waste blocks to remove per period (years or quarters) to maximize the discounted cash flow over the life of the mine. A set of operating constraints was carefully selected so that the following functions are controlled: (1) the removal of overburden by preproduction and production stripping exposes a fixed amount of ore; (2) a constant manpower and equipment usage is insured (except for trucks); (3) the tons of mill ore, concentrate, and stockpiled ore are regulated; (4) the number and extent of shovel moves are minimized; (5) the grindability of the rock is considered as well as the variable haulage cost caused by variable haulage distances and depths; and (6) the size of the shovel working area is regulated. As many as 50 alternate schedules can be produced per computer run. They are arranged in descending order starting with the best solution.

Jan 1, 1975

By Irwin Politziner F. M. Townsend, L. S. Reid

Recently published data indicate that the water vapor content of a gas, as determined by dew point measurement, is inaccurate when the gas has been dehydrated with diethylene glycol. Water vapor contents and dew point measurements of gases dehydrated with triethylene glycol have been obtained in this investigation in order to determine the magnitude of a similar error, if one exists. Experimental data show a very low concentration of triethylene glycol vapor in gases dehydrated at atmospheric ternperatures and pressures ranging from 500 to 2,500 psia and that the accuracy of dew point measurements is not impaired by the presence of triethylene glycol vapor. INTRODUCTION Nearly all natural gas transported by pipe line to northern and eastern markets must be dehydrated to a low residual moisture content in order to assure maximum transmission efficiency and continuous delivery under peak load conditions. Without dehydration, water vapor often condenses in pipe lines in quantities sufficient to restrict the flow3 and. under low atmospheric temperature conditions, gas hydrates may form and plug gathering. transmission and distribution facilities. Gas may be dehydrated to pipe line specifications by a number of methods. The most widely used methods are (1) adsorption of water vapor on a solid dessicant such as activated bauxite, alumina or silica gel,' (2) by absorption of water vapor by either diethylene or triethylene glycol-water solutions of high glycol concentration,11,13 and (3) by simultaneous expansion-refrigeration of very high pressure gas in which gas hydrates are purposely formed and then quickly decomposed.'"" Of these three fundamental methods, the adsorption and absorption processes provide the bulk of the dehydrated gas moving to market at the present time. The expansion-refrigeration process. a relatively new development, is gaining in favor because of its simplicity but is sharply limited in its application by available differentials between source and gathering system pressures. Where gas sale or purchase contracts contain a maximum water vapor content specification, the water vapor content is usually determined by measuring the dew point of the gas at system pressure. Knowing he dew point temperature and the system pressure, the water vapor content of the gas is determined from a graphical correlation of saturation, or dew point, temperature us the water vapor content of the gas which is customarily expressed as pounds of water vapor per million cubic feet of gas measured at 14.7 psia and 60°F. Dew points are usually measured with the U. S. Bureau of Mines Dew Point Tester. shown in Fig. 1, which is well suited for use at temperatures lower than 120°F and at pressurei; ranging from atmospheric to 3,000 psi. A number of correlations of dew point temperatures vs water vapor content are available,3,5,15 the most recent of which is that by McCarthy et al.4 Where natural gas is dehydrated by absorhing contact with concentrated diethylene glycol-water solutions. considerable difficulty is experienced in observing water dew points due to condensation of liquid hydrocarbon and glycol films on the mirrored surface of the dew point tester. Riesenfeld and Frazierl2 report that the dew point method for determining the water vapor content of a dietllylene glycol-treated natural gas is in error due to the glycol content of the condensate formed on the tester mirror, and that the water vapor content of the gas tested is actually lower than that indicated by the standard' dew point-water vapor content correlation. Extensive experience in testing gases dehydrated by concentrated triethylene glycol-water solutions lias not revesled difficulties of the nature cited above for diethylene glycol. Water dew points are clear and sharp and condensation of

Jan 1, 1951

By L. S. Reid, Irwin Politziner F. M. Townsend

Recently published data indicate that the water vapor content of a gas, as determined by dew point measurement, is inaccurate when the gas has been dehydrated with diethylene glycol. Water vapor contents and dew point measurements of gases dehydrated with triethylene glycol have been obtained in this investigation in order to determine the magnitude of a similar error, if one exists. Experimental data show a very low concentration of triethylene glycol vapor in gases dehydrated at atmospheric ternperatures and pressures ranging from 500 to 2,500 psia and that the accuracy of dew point measurements is not impaired by the presence of triethylene glycol vapor. INTRODUCTION Nearly all natural gas transported by pipe line to northern and eastern markets must be dehydrated to a low residual moisture content in order to assure maximum transmission efficiency and continuous delivery under peak load conditions. Without dehydration, water vapor often condenses in pipe lines in quantities sufficient to restrict the flow3 and. under low atmospheric temperature conditions, gas hydrates may form and plug gathering. transmission and distribution facilities. Gas may be dehydrated to pipe line specifications by a number of methods. The most widely used methods are (1) adsorption of water vapor on a solid dessicant such as activated bauxite, alumina or silica gel,' (2) by absorption of water vapor by either diethylene or triethylene glycol-water solutions of high glycol concentration,11,13 and (3) by simultaneous expansion-refrigeration of very high pressure gas in which gas hydrates are purposely formed and then quickly decomposed.'"" Of these three fundamental methods, the adsorption and absorption processes provide the bulk of the dehydrated gas moving to market at the present time. The expansion-refrigeration process. a relatively new development, is gaining in favor because of its simplicity but is sharply limited in its application by available differentials between source and gathering system pressures. Where gas sale or purchase contracts contain a maximum water vapor content specification, the water vapor content is usually determined by measuring the dew point of the gas at system pressure. Knowing he dew point temperature and the system pressure, the water vapor content of the gas is determined from a graphical correlation of saturation, or dew point, temperature us the water vapor content of the gas which is customarily expressed as pounds of water vapor per million cubic feet of gas measured at 14.7 psia and 60°F. Dew points are usually measured with the U. S. Bureau of Mines Dew Point Tester. shown in Fig. 1, which is well suited for use at temperatures lower than 120°F and at pressurei; ranging from atmospheric to 3,000 psi. A number of correlations of dew point temperatures vs water vapor content are available,3,5,15 the most recent of which is that by McCarthy et al.4 Where natural gas is dehydrated by absorhing contact with concentrated diethylene glycol-water solutions. considerable difficulty is experienced in observing water dew points due to condensation of liquid hydrocarbon and glycol films on the mirrored surface of the dew point tester. Riesenfeld and Frazierl2 report that the dew point method for determining the water vapor content of a dietllylene glycol-treated natural gas is in error due to the glycol content of the condensate formed on the tester mirror, and that the water vapor content of the gas tested is actually lower than that indicated by the standard' dew point-water vapor content correlation. Extensive experience in testing gases dehydrated by concentrated triethylene glycol-water solutions lias not revesled difficulties of the nature cited above for diethylene glycol. Water dew points are clear and sharp and condensation of

Jan 1, 1951

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By Vanderlei Beisiegel, Arthur L. Bernardelli, Arthur W. Ruff, John H. Tremaine

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 per cent iron, 2.2 per cent combined silica and alumina, and 0.05 per cent phosphorous on a dry basis. Hematite is predominant and no significant sulfur on other deleterious elements are present. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air.

Jan 1, 1974

By L. P. (Les) Haldane

Building a small underground coal mine is a risky endeavor, especially in the recent economic environment. ARCO's Mt. Gunnison No. 1 Mine, located in western Colorado, was designed and built as a small expandable speculation mine with initial production to be sold on the spot market, so it was very important to minimize capital exposure. This mine, operated by West Elk Coal Company, a subsidiary of Anaconda Minerals, was successfully built under budget at $35 million, and has been operating successfully since completion of construction in late 1982. The initial planning phase of a project is extremely important for testing the economic and technical feasibility of a proposal. The construction phase, by contrast, carries with it significant cost and quality risks which can relate to long-term economic and operating problems and therefore directly affect the viability of the project. This paper discusses several different aspects of the cost overrun risk involved in building an underground coal mine, and how attempts were made to minimize these risks during construction of the Mt. Gunnison Mine. Good people, construction planning, and execution are essential factors in assuring a quality, cost-effective project, with corresponding risk minimization during the construction phase and long term favorable implications for the operating phase.

Jan 1, 1985

By R. C. Mahon

THE importance of ground water control in glacial drift overlying mines is widely recognized. Adequate handling of the problem results in consider- able saving in overall pumping costs, as the cost of pumping the larger quantity of water under low heads from surface wells is more than offset by the decrease in the quantity of water to be pumped from the mine under high heads. Eliminating or partly reducing seepage of water through the ledge reduces moisture content of the ore, a factor especially important in iron ore mines, where a reduction of 1 pct in moisture effects a very material saving. An important though indeterminate saving is also brought about by the elimination of water in the working places underground. The Homer and Wauseca mines of Hanna Coal & Iron Co. at Iron River, Mich., cover 480 acres. When these mines were started it was possible to operate on only one 40-acre tract, as the depth of water over the remainder of the property was too great to permit operation. Although the average depth of the ground water over the area being mined at that time was less than 50 ft it was necessary to pump 1200 gpm from the mine, the greater part from a depth of 750 ft. The slate footwall and graywacke hanging wall are almost impervious, and it was apparent that seepage into the mine was mainly through the iron formation in which the orebodies were located. Analysis of the water in the iron formation showed it to be of the same character as that in the glacial drift, while the water in both walls was heavily mineralized, also indicating that the water passed much more freely through the iron formation.

Jan 6, 1954

By Nicholas Chlumecky

To date information is somewhat limited concerning the strength and bearing capacity of floor strata, which is of great importance where proper roof control is desired. If the bearing strength of strata is not known, the support may be excessively strong in relation to the support capacity of the floor, with the result that strong props sink into the floor strata, giving them dubious value as a roof support. The method described is used to determine how tests are made on dry rock to determine the required support area for the base of props or other structures which may rest on rock strata in mines. Relationships were established for the bearing capacity of rocks which were subjected to loads by means of bearing areas of various sizes ranging from 0.09 sq cm (.014 sq in.) to 700 sq cm (108.5 sq in.). This permits the evaluation of the bearing capacity of rocks by testing small areas for the de- termination of the capacity of larger areas.

Jan 3, 1968

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.01 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.06 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength 0f from 100 t0 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By N. J. Grant, A. W. Mullendore, Y. Ishida

Creep tests were performed at 500°F on polished specimens of A1-3 pct Cu at stresses of 2000, 4000, and 6000 psi. The effects of the size and distnbution of the second phase were studied in connection with the mechanisms of deformation, especially grain boundary sliding. Although the amount of grain boundary sliding varied considerably for the different heat treatments, yestriction of grain boundary sliding is not due primarily to precipitate on the grain boundary. NUMEROUS prior investigations of grain boundary sliding, notably those of McLean, 1 Rachinger, 2 Rhines, Bond, and Kissel, 3 and Brunner and Grant,4 have established the importance of this phenomenon in the deformation of pure aluminum and its solid-solution alloys at elevated temperatures. An extension of this kind of study to the case of a simple two-phase structure is an important step towards understanding the deformation behavior of more complex alloys. A two-phase A1-3 pct Cu alloy was selected for this study. The creep behavior of alloys in this system has been studied by Sully and Hardy,5 by Underwood, Marsh, and Manning,' and by Pelloux, Chaudhuri, and Grant.7 In these studies, the prior heat treatments were such that some precipitation took place during the tests in most cases. Pelloux, Chaudhuri, and Grant7 studied the creep of A1-2 and 3 pct Cu alloys in the overaged condition. Their results indicated that the structure most effective in promoting high-temperature strength consisted of a fine, closely spaced grain precipitate and large, widely spaced particles on the grain boundary. The present work consists of quantitative meas- urements of grain boundary sliding during creep of an A1-3 pct CU alloy with four different precipitate distributions. The aims were to quantitatively define the role of the second phase on grain boundary sliding, and to obtain information regarding the mechanism of grain boundary sliding. MATERIALS AND PROCEDURE A high-purity A1-3 pct Cu alloy, kindly supplied by Alcoa, was used in this investigation. The composition of the alloy in weight percent was as shown in Table I. This composition is such that A12Cu exists as a second phase at temperatures below 850°F. A homogeneous grain size of 0.6 to 0.8 mm was obtained by annealing the machined test bars for 5 min at 1000°F, furnace cooling to 930°F, and homogenizing for 5 hr. Following the recrystalli-zation and homogenizing anneal, four different heat treatments shown in Fig. 1 were utilized. The F7 and F5 treatments utilize a furnace cool to the aging temperature while Q7 and Q5 have a water quench from the homogenization temperature before aging. Figs. 2 to 5, and Table 11, show the size and shape of precipitate dispersions obtained with the above heat treatments. The heat treatments produce variations in the dispersion both in the grains and along the grain boundaries. Precipitate particles along the grain boundaries are rounded and large (about 1.5 p diameter) in the F5 and F7 structures (Figs. 3 and 5). The grain boundary precipitate was somewhat smaller (0.9 p diameter) in the Q7 structure and no grain boundary precipitate was detected in the Q5 structure using light microscopy. The pre-

Jan 1, 1964

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summay. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented. While prospecting for mineral deposits, geologists are frequently asked what they hope to find or have found. The response is usually descriptive, such as "50 million tons of 1% copper," and the economic implications are deferred until a capital investment decision is required. At that time, a financial analysis integrating the four analysis components is completed. These components are: 1) Tonnage and Average grade above cutoff grade 2) Capital and operating costs 3) Product value 4) Appropriate profit or loss accounting Close examination of these components reveals that there is no intrinsic reason for avoiding financial analyses at earlier stages in exploration, as long as the uncertainty of the estimate is realized. Tonnage and average grades are commonly estimated at early stages in exploration. For this component, the appropriate cutoff is the major uncertainty. Capital and operating costs are difficult to estimate before detailed quantitative information is available, but estimates useful for the types of applications pertinent to earlier exploration stages are possible. Product value estimates may or may not be difficult, depending on the pricing structure of the particular commodity. A simplified accounting procedure usually may be adopted without introducing any significant loss of validity. This paper describe some of the financial analysis applications which are pertinent during mineral exploration and deposit development. These applications lend additional insight during exploration planning, land acquisition, physical exploration, and development. The examples are oriented toward a hypothetical management investment policy which is based on a single criterion, a minimum 15% discounted cash flow rate of return. In reality, managements use multiple criteria. This simplification is convenient for purposes of presentation and does not invalidate the examples. Computers are useful, but not a requirement, for the applications described. The use of computers provides the results on a more timely basis at costs lower than equivalent manual computations. UNDERLYING PRINCIPLES AND ANALYSIS METHODS Data estimates are subject to uncertainty. The analyst may choose to assess this uncertainty by using one of two principles. Each principle has some advantages. The principle most commonly employed is "assumed certainty." Each financial analysis is based on one set of selected data, which may represent the average estimates, minimum expected conditions, etc. The critical data is identified by making successive calculations, varying the values used. Such studies, called sensitivity analyses, isolate the economic effect of various uncertainties, and guide the allocation of future efforts toward improving the overall accuracy of the analysis. A second principle, "assumed risk," examines the interactive effect of the current uncertainties by qualitatively assigning probability distributions to each data element. These probability distributions indicate the currently appraised chance that a given numerical value will prove to be true. The corresponding procedure, risk analysis, consists of processing many individual financial analyses, each analysis being based on randomly selected numerical values from the probabilistic distributions. The result is a numerical presentation of the uncertainty, but care must be exercised in the interpretation of results. The advantage of this procedure is the direct measurement of economic uncertainty caused by the interaction of uncertain estimates. Kennecott Copper Corp. has developed computer systems for accomplishing sensitivity and risk analyses.

Jan 1, 1970

By W. S. Ayres

A BRIEF history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name Lt breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the "breaker-boy " as a slate-¬picker, with his ever-increasing capriciousness. As the richer veins or ? splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities; particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complication yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Dec 1, 1909

By Gilbert E. Doan, William C. Schulte

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By William C. Schulte, Gilbert E. Doan

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936