Search Documents

By WALTER B. JONES

IN ALABAMA there are three distinct groups of bauxite deposits, as follows: (1) Cambro-Ordovician contact with the principal-deposits located in Talla-dega, Calhoun, DeKalb, and Cherokee Counties, and in adjacent portions of the State of Georgia. (2) Midway-Nanafalia contact, with the principal deposits in Barbour and Henry Counties, and in adjacent portions of Georgia; also in North-eastern Mississippi. (3) Mississippian - Cretaceous contact, with a group of deposits centered around Margerum in Colbert County. For the purpose of more clearly describing bauxite mining in the state, past, present and possible future, these three groups will be described separately.

Jan 1, 1934

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By Richard P. Rothwell

The ores treated by the Canada Consolidated Gold Mining Company at Deloro, Ontario, have been described in a paper read before the Institute in 1881. They are gold-bearing arsenical sulphurets of iron (mispickel), carrying the theoretical proportions of 42 per cent. of arsenic, 20 per cent. of sulphur, and the remainder iron. The gangue is quartz, calc spar, and some talcose, slaty rock, evidently resulting from the decomposition of the wall-rock, which on each side of the veins is syenitic granite. The treatment of the ore consists of: 1. Crushing. 2. Concentrating.

Jan 1, 1883

By James F. Kemp

The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.' The further remark may, however, be made that the

Jan 1, 1915

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

H. Schwartzbart and W. F. Brown, Jr.—The authors have divided the effects of recovery on the true stress-true strain curve into two types; metarecovery, which effects only the first part of the curve or the yield strength, and orthorecovery, which effects the flow stress at any strain. Both of these are said to be true recovery effects, involve no recrystallization, and are explained by the removal of two different types of imperfections caused by work hardening. However, there seems to be some question as to whether the data are sufficiently conclusive to exclude, as an explanation of the authors' results, a mechanism based on the relief of residual stresses between the grains or slip bands and recrystallization. It appears that metarecovery could be interpreted in the same fashion as a customary interpretation of the Bausch-inger effect. The balanced system of internal stresses which exists between grains in a strained specimen due to varying orientation and, hence, yield strengths, of the different grains is responsible for a reduced yield strength in compression following pre-tension, and, similarly, for an elevated yield strength in tension following pre-tension. If the specimen is now heated so that the internal stresses are relieved by creep, then the yield strength in tension following tension will have been reduced and in compression following tension will have been raised. There seems to be a very strong case for the lack of recrystallization in the aluminum investigated by the authors, if one defines recrystallization as the presence of visually detectable new grains or accepts the X-ray evidence as conclusive. One must remember, however, that the appearance of spots on the back-reflection X-ray patterns cannot be taken as the time when recrystallization first started. The areas of recrystallized strain-free material must first have grown to a size large enough to give distinct spots on the patterns and this may take some time. Averbachl7 in an investigation of brass has shown that recrystallization can be detected by extinction measurements at temperatures lower than those based on hardness or X-ray line width determinations. It can be seen from fig. 10 that the rate of recrystallization is extremely low over a considerable time period at the onset of the process. Observations on the rate at which small amounts of recrystallization effect the flow stress would have given further insight as to whether undetectably small amounts of recrystallization might have been responsible for orthorecovery. Also, the question arises as to whether the effects observed in fig. 6 for various times and temperatures could not have been obtained if the time at 212°F were sufficiently long. In addition, the argument that the curve in fig. 10 is not sigmoidal seems weak in view of the scattering of the points. It is conceivable that an accurate determination of the curve for the first 100 hr would exhibit a relationship other than the one drawn. There is one point we would like to raise about the condition of the starting material. The authors annealed their material at 750°F for 15 min to remove the effects of any previous work hardening or machining strains. Reference to the work by Anderson and Mehl shows that this treatment may not have completely recrystallized the aluminum, so that the starting material may have had some strained areas. Higher temperatures or longer times may have been required to remove the effects of any small strains. We would like to mention some results of tests being conducted at the Lewis laboratory of the National Advisory Committee for Aeronautics in an investigation of the Bauschinger effect in relation to fatigue. Tests were performed on annealed electrolytic copper and several annealed brasses. Specimens were pre-strained 1 pct in tension and then tested in compression or tension with and without intermediate stress-relieving annealing treatments at 500°F for various times. Specimens heated at 500°F for 10 1/2 hr showed an elevation of the flow curve in compression and an approximately equal lowering of the flow curve in tension when compared with the curves for the un-heat treated specimens. After approximately 0.8 pct strain, all flow stresses coincided and were equal to the flow stress of the virgin material at this strain. This behavior is consistent with the metarecovery observed for aluminum by the authors and for which a residual stress model can be used. On the other hand, increas-

Jan 1, 1951

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By John J. Elango

Strain gage load cells, the most widely used type of nonmechanical weight sensor, are capable of taking measurements between 0.45-4.5 million kg (1-1 million lb) with an accuracy of 0.05%. They are available in a wide range of standard capacities, configurations, and accuracies, and special load cells may be custom-manufactured to meet unusual requirements. Typical applications include automated batch processing, process monitoring and control, mixing of powders and liquids, weighing coal or other materials in silos, and in large platform systems that weigh trucks and railcars. Because the strain gage load cell produces an electrical signal proportional to the applied load, it readily interfaces with readouts, keyboards, computer terminals, and alarm systems.

Jan 6, 1979

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By D. J. Carney, R. L. Stephenson

A sampling technique has been developed for procuring a sample of sinter representative of the entire depth of the sintering bed. The sampling method involves the use of an open-bottom metal basket that rides on the grate of the sintering machine and when removed contains a sample of the sintered product. Additional data have been obtained to indicate that the tumbler test is a suitable means of measuring sinter strength. IN the last few years additional sintering facilities have been installed in both the Pittsburgh and the Chicago district of the United States Steel Co. Since the construction of these sintering plants made possible the use of higher percentages of flue-dust sinter in our blast-furnace burdens, it became important to study means of controlling the quality of sinter to obtain optimum results in the blast furnace. For controlling an operating process, it is necessary first to establish standards by which the quality of the product can be judged. For sinter, it appeared that an important property was its strength or its resistance to degradation during transportation and charging into the furnace. Consequently work was undertaken to establish a standard for sinter strength that could be used both for controlling sintering-plant operations and for correlating sinter quality with blast-furnace performance. The first problem in setting up a standard was that of procuring a sample that would be representative of the sinter made under any particular set of conditions at the sintering plant. Since the United States Steel Co. sintering plants discharge the finished sinter either into a large pit or onto a rotary cooler, the sinter becomes inseparably mixed with material sintered 2 hr before or 2 hr afterwards. For this reason the exact identity of the sinter is lost. A sample selected as the cooler is discharged, or as the sinter is removed from the pit, cannot be said to be truly representative of the sinter made at any specific time. Sampling The first attempt to procure a sample that would be representative of a specific sinter mix and of specific operating conditions was made by stopping the Dwight Lloyd sintering machine and removing an entire pallet full of sinter. This method, however, proved very difficult to perform and interfered considerably with the operation of the plant. To overcome this difficulty, a sampling method was devised by technologists at South Works enabling them to secure, without interrupting the sintering operation, a sample of about 1 cu ft of sinter, representative of sinter for the full depth of the sintering bed. The South Works method involves the use of a steel-frame-work basket. A typical basket is shown in Fig. 1. The basket has been used both with and without crossbars along the bottom. As long as the crossbars are in the same direction as the grate bars on the sintering machine they do not interfere with the sintering process. The basket is set on an empty grate of the Dwight Lloyd sintering machine before it passes under the swinging feed spout, see Fig. 2. When the basket is removed after it has travelled the length of the sintering machine, it contains the sample. Just before the basket is removed, the sinter is scored and chipped to facilitate removal of the sample from the sinter bed. A view of the basket after its removal is shown in Fig. 3. Although the sampling method was originally designed for use on a Dwight Lloyd sintering machine, it can also be used on the Greenawalt type of machine. When used on the Greenawalt-type machine, the basket is placed on the sintering grate before the charging car passes over it, and finally it is removed just before the pan is dumped. Testing After a method of obtaining a representative sample of sinter had been developed, the next step was to select a method of measuring its strength. The irregular shape and size of the sinter pieces precluded the use of a simple compression test for determining strength; consequently, the shatter test and tumbler test were investigated. To perform the shatter test, a sample of sinter, approximately 5 lb, is dropped from a hinged-bottom box at a height of 3 ft onto a steel plate. The broken sinter is sieve-analyzed after a specified number of drops. The tumbler test is performed with the use of a standard ASTM coke-tumbling drum. The drum is 3 ft in diam and is equipped with two lifter bars diametrically opposite one another on the inner periphery of the drum. The drum is rotated at a speed of 24 rpm for 200 revolutions, and after tumbling the sample is sieve-analyzed. To express as single numbers the results of sieve analyses after shattering or tumbling, the method suggested by R. E. Powers1 was employed. This method involved plotting the size of the sieve openings on a logarithmic scale and the cumulative per cent larger than each sieve on a probability scale as described by J. B. Austin.' By interpolating from the plotted data, which in most cases approximated

Jan 1, 1954

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount, of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and-slimes. The reason for this is that in almost every, dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus,, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the .place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of. years, two general types of machines evolved for the treatment of fine sands and slimes :- The so-called concentrators and vanners, on the one hand, and the huddles and round tables on . the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By A. J. Lanza

The prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would markedly increase their liability to accident. The number of men working underground in mines in this country whose physical condition totally unfits them for such work presents a situation that should not be allowed to continue, and which I believe is not equalled in any other industry in the country. There is but one way to secure men who come up to the required standard, and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to be said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a basis that they can be administered in a just and equitable manner free from the abuses and suspicions to which they have been subject in the past.

Jan 1, 1919

By C. D. Starr

IT is well known that the martensite reaction can be induced to occur isothermally above the M, temperature by plastic deformation of an alloy in its austenitic state, and also that as the test temperature is increased above the M. temperature, plastic deformation under a given set of conditions merely causes additional slip with a corresponding tendency toward the formation of less martensite per unit of strain. Thus it appears that a maximum temperature exists above which martensite cannot be formed isothermally by plastic deformation. This temperature is commonly designated as the equilibrium temperature Te. Attempts to determine experimentally the equilibrium temperature have indicated that a critical temperature is observed, under a given set of conditions, above which martensite cannot be formed isothermally by plastic deformation. But the observation of a "so called" critical temperature, Te, should not be confused with the equilibrium temperature, Te. In order to clarify this anomaly, true stress-strain curves were obtained for a series of type 304 stainless steel specimens (manufacturer's analysis, 0.08 pct C, 18 to 20 pct Cr, 8 to 10 pct Ni, balance Fe) over the temperature range 67" to 300°K.' Since martensite is magnetic, a quantitative measure of the amount of martensite that was produced by plastic deformation was obtained by determining the magnetic permeability as a function of strain. The results of these tests are given in Fig. 1. They appear to indicate that a plastic critical point does exist at about 240°K for the stainless steel under investigation here. But that 240 °K is not the equilibrium temperature nor even a true plastic critical temperature can be seen from Fig. 2 wherein the permeability of the same material is shown to increase with cold rolling at 293 OK. Consequently the observation of a "so called" plastic critical temperature is dependent on the mode of deformation and has no theoretical significance. Acknowledgment This work was sponsored by the Office of Naval Research. Permission to publish this note is gratefully acknowledged.

Jan 1, 1954

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).' A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;' however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963

By A. Thies, Wm. B. Phillips

1. Introductory Remarks.—The Haile Gold Mine is in Lancaster county, South Carolina, 3 1/2 miles east of Kershaw station on the Charleston, Cincinnati and Chicago Railway. It was first opened about, the year 1832, and since that time has passed through various fortunes. Many different operations have been practiced here for extracting the gold : panning, grinding in Chilian mills or arrastras, stamping, the Designolle process, dry-crushing, and finally the Thies process of barrel-chlorination, which has now been in successful use for 2 1/2 years, and by which 36,000 tons of ore have been treated profitably. The Thies process is in brief the treatment of dead-roasted auriferous concentrates (pyrite, sometimes also chalcopyrite, as at the Phœnix mine, Cabarrus Co., N. C.) with nascent chlorine, without ' artificial pressure or exhaust, in lead-lined iron cylinders; the throw-

Jan 1, 1891

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen' has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By Herbert D. Drechsler

The objective of this paper is to identify the components of income above that necessary to keep a mine in production and relate those components to the profits of a mining firm. This is a discussion of "Economic Rent". Economic rent is the payment to the factors of production -- capital, labour, entreprenuer and the owner of the mineral deposit -- above the minimum necessary to keep all of these factors cooperating in the production of minerals from a particular deposit. THE SOURCE OF ECONOMIC RENT IN THE MINING INDUSTRY In the mining business each mine has a unique cost of production unrelated to any other mine. The cost of production is developed from many factors such as the technical characteristics of the deposit: depth of deposit, depth of overburden, areal extent, and type of deposit. Furthermore, there are locational factors which also alter cost of production. For example, identical mineral deposits located in Zambia or in the southwest U.S.A. would have different capital and operating costs. These differences occur because of different qualities of labour, ease of acquisition of operating supplies or investment capital and other similar factors. To explain the source of rent, we shall use ideas developed by Alfred Marshall and Kenneth Boulding. Suppose a meteorite with special qualities exploded over earth and sent showers of small meteorites to the ground in various places. At some point in time, people learned of the special qualities of these meteorites and a demand arose and one mine was started. Suppose further that the cost of production to produce these meteorites was different for each deposit. Probably the lowest unit cost mine would commence production because if a higher unit cost mine started-up, eventually someone would discover a deposit that had a lower unit cost of production. The lower unit cost mine would take over the market and the high unit cost mine would cease production. The cost curve for the first mine would look like the following Figure 1. [ ] The output for the first mine is on the horizontal axis with the cost per ton on the vertical axis. The curve labelled AC I is the average total cost of production over the range of possible production that could occur at the property. The total costs are composed of variable costs, which are dependent on output and fixed costs, which are dependent on time. For example, the cost of operating supplies would be a variable cost and normal profit would be a fixed cost.1 The opportunity cost of the investment would also be part of the fixed costs. In our example, all factors of production, are receiving the minimum necessary payment that will keep the mine operating. The average total cost curve is U-shaped because at zero output, the meteorite mine has no variable costs, only fixed costs which, on a unit basis, obviously are very high. To produce a small output of meteorites, the mining firm adds

Jan 1, 1985

By RICHARD L. HUMPHREY

IT IS proper that there should be a brief accounting of the stewardship which was entrusted to the Joint Conference Committee by resolution adopted by the. Organizing Conference on June 4, 1920, in part as follows: RESOLVED, that it is the sense of this Organizing Conference that the Joint Conference Committee should be entrusted with making provision for putting the conclusions of this Conference of engineers into effect, etc. Pursuant to this authority, the Joint Conference, Committee has acted as an Ad-interim Committee has- prepared, a synopsis of the proceedings of the Organizing .Conference, has edited and published the Constitution and By-Laws adopted by this Conference, and. has issued an invitation to become Charter Members of The Federated, American Engineering Societies; to the list of organizations to whom invitations had been extended to attend 'the Organizing., Conference. The Committee in connection with this invitation offered to the extent of its ability, such assistance as might be-desired; and arranged in many cases for one or more of its members to be present when the matter of membership in The Federated American Engineering Societies was considered. . .

Jan 1, 1920

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By John Fritz

THE John Fritz Medal was presented to Ambrose Swasey of Cleveland, Ohio, in the Auditorium of the Engineering Societies Building, in New York, on April 23. Charles F. Rand, Chairman of the Board of Award, presided and, after speaking very briefly of Mr. Swasey, whose friend he has been for a great many years, ,introduced Gen. William Crozier, formerly Chief of Ordnance, U. S. Army, who spoke most entertainingly of, Mr. Swasey's accomplishments in designing and manufacturing instruments of precision, particularly for the use of artillery in range finding: Dr. William Wallace Campbell, Director of the Lick Observatory, and President of the University of California, described Mr. Swasey's, contribution to astronomical advancement by his notable development of the largest telescopes in this country.

Jan 1, 1924