Search Documents

By Plato Malozemoff, A. M. Gaudin

IN modern practice the major portion of an ore is reduced to flotation size by fine grinding. As the result of grinding fine enough to liberate most of the minerals, a substantial portion (generally 5 to 15 per cent) of the ore is inadvertently reduced to a size much finer than that necessary for liberation. This portion of most flotation pulps is very refractory to recovery by flotation. A reduction of one-quarter or more in recovery in this range of extremely fine particles can be observed. The loss in metals caused by overgrinding is appreciable. That this loss is characteristic of very fine particles has been suspected for some time;(l)† however, it was definitely quantified only recently.(2) Definite reduction in float-ability with reduction in particle size beyond a critical size of maximum floatability can be accepted now as an established fact. Formulating the Hypothesis In looking for the cause of the ill behavior of the finest particles it may be well to consider the essential differences between fine and coarse particles. A difference that immediately comes to mind is their intrinsic difference in size and consequently in relative extent of surface. If one agrees that attachment of mineral particles to bubbles must follow direct encounter of particles with bubbles one is forced to conclude(3) that the probability of encounter between a mineral particle and a bubble varies directly as the size of the particle, provided the particle is small compared to the bubble. In other words, the finer the particle the poorer its chance of being recovered in a given time of flotation. There is an effect, implicit in this theory, which should overcome the effect of excessive fineness of the particles; namely, flocculation of the particles. The floccules can be conceived as being simply larger particles and therefore capable of becoming attached to bubbles. And, indeed, in all the cases in which a sulfide mineral of near-colloidal size was successfully floated the mineral (but not necessarily the gangue) was flocculated. Moreover, it was shown experimentally(4) that galena previously flocculated by inorganic flocculators and then added to gangue

Jan 1, 1935

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By Frank Firmstone

IN the early decades of the past century the method of starting iron blast-furnaces by "scaffolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important "Reminiscences" printed by the late Samuel Thomas. I It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.' On the Continent it was still followed in the 60's,3 and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom '4 scaffolding" was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country:

Mar 1, 1907

By F. W. Gibson

A detailed description of the smelting and refining operations of the Amax-Homestake Lead Toller's smelter at Buick, Missouri. This is one of two completely new lead smelting and refining operations to go into operation in the United States in over forty years. Incorporated into the operation are the new methods and equipment which have been developed and lend themselves to the particular metallurgy of this plant. The text, as well as the statistical data presented, represent actual current practice after 22 months of operation, and although the metallurgy is considered to be relatively simple, several metallurgical problems unique to Missouri concentrates are discussed.

Jan 1, 1970

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By Sir Robert Hadfield

SINCE the writer has been intimately connected with the development of manganese steel for many years, some remarks upon the early work with regard to the rolling and forging of this material might he of interest, and particularly as to the question of rails of special quality and of superior wearing qualities. In a paper on Iron Alloys, with Special Deference to Manganese Steel, read before this Institute at the International Engineering Congress in Chicago in 1893,1 the writer mentioned that, about 20 years ago, his firm in Sheffield produced railroad material, such as tires and axles, of forged and rolled manganese steel, thus showing that this product could be manipulated and worked up into the various required forms. The tires illustrated in the paper referred to above formed a particularly difficult class of work to produce in a special steel, but no special obstacles were met with Although there was no difficulty at that time in making and producing manganese steel in various forms, forged, rolled or pressed; nevertheless, on account of its higher expense, sufficient encouragement

Jan 2, 1914

By M. Gell, G. R. Leveran

The high- and low-cycle fatigue properties of the nickel-base superalloy, Mar-MBOO, in columnar-grained and single-crystal forms were determined at room temperature. It was found that the fatigue lives of these materials were greatly affected by the size of preexisting cracks in MC-type carbides contained in the micro structure. Most of the data falls on two curves given by: (zN)'/A€= K, where Nf is the number of cycles to failure, Af is the total strain range, and K is a function of carbide size. No difference was observed in the fatigue behavior of the columnar-grained and single-crystal materials for the same MC carbide size. Matrix slip and crack initiation occurred at precracked MC carbides and, to a lesser extent, at micropores. Fatigue crack propagation was mainly in the Stage I mode, i.e., on cry stallo graPhic slip planes. The Stage I fracture in these materials was unusual in that distinct features were observed on the fracture surfaces. In high-cycle fatigue, these features resembled those commonly observed on the cleavage fracture surfaces of bcc and hcp materials. Yet, in this study, the cracks propagated slowly in a cyclic manner. In low-cycle fatigue, the Stage I facets contained equiaxed dimples, similar to those observed on the tensile fracture surfaces of ductile materials. These observations indicate that both local normal and shear stresses are involved in these Stage I fractures. A model is proposed to explain these results based on the weakening of the cohesive energy of the active slip planes by reversed shear deformation and the fracture of the bonds across the weakened planes by the local normal stress. RECENT developments in casting technology have produced cast nickel-base superalloys in columnar -grained and single-crystal forms.1'2 The tensile and creep properties of the nickel-base superalloy, Mar-M200, cast in these forms have been shown to be superior to the corresponding properties of the conventionally cast polycrystalline material.lp2 This improvement in properties results, in part, from the elimination of grain boundaries in the single crystals and the alignment of the grain boundaries parallel to the stress axis in the columnar-grained castings. As part of a program to evaluate the fatigue properties of nickel-base superalloys cast in single-crystal and columnar-grained forms, a study has been made of the cyclic deformation and fracture of Mar-M2OO at room temperature. M. fiFl I .hininr Mpmher AIMF ic ^pninr Rocoarrh Accn^iata anH I) EXPERIMENTAL PROCEDURE The composition range of Mar-Ma00 in weight percent is: 8 to 10 Cr, 9 to 11 Co, 11.5 to 13.5 W, 0.75 to 1.25 Cb, 1.75 to 2.25 Ti, 4.75 to 5.25 Al, 0.01 to 0.02 B, 0.03 to 0.08 Zr, 0.07 to 0.12 C, bal. Ni. All of the castings met the above specifications. The castings were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr which resulted in a 0.2 pct offset yield stress of 150,000 psi at room temperature. The microstructure of the material consisted of cuboidal, coherent particles of ordered, fcc Ni3(A1,Ti) (commonly designated y'), approximately 0.3 p on edge, distributed in an fcc y solid-solution matrix. MC carbides together with shrinkage and gas micropores were also distributed throughout the materials. The MC carbides and micropores were located preferentially in the interdendritic interstices, as well as in the grain boundaries in the columnar-grained castings. The (100) direction of all the single crystals and the common (100) axis of the grains in the columnar materials were aligned within about 5 deg of the specimen axis. Fatigue testing was carried out in the high-cycle (HCF) and low-cycle (LCF) fatigue regions, with the major difference being gross yielding of the specimen occurred during the first cycle in the LCF region. This division also corresponded with the more usual one in which the life of a specimen in LCF is less than lo4 cycles and that in HCF is greater than lo4 cycles. The designs of the high-cycle fatigue and low-cycle fatigue specimens are shown in Figs. l(a) and (c), respectively. The gage sections of both HCF and LCF specimens were electropolished prior to testing. The HCF specimens were tested in an MTS, closed-loop, hydraulic fatigue machine at 10 cps in air. The specimens were cycled between a tensile stress of 5000 psi and a maximum tensile stress which ranged from 35,000 to 125,000 psi, Fig. l(b). The LCF specimens were cycled under strain control from zero to a maximum tensile strain, Fig. l(d), in a Wiedemann-Baldwin testing machine. The experimental procedure has been described elsewhere.3'4 Both HCF and LCF tests were interrupted periodically in order to replicate the development of slip and cracking at the specimen surface. This was accomplished by placing plastic replicating tape around the gage section of the specimen while the specimen was in the mahine. The size of the MC carbides for all specimens was measured on a polished longitudinal section through the gage section after fatigue testing. The method of measurement consisted of carefully scanning the entire polished section in order to locate the largest MC carbides. Photographs were then taken of the six longest carbides oriented approximately normal to the

Jan 1, 1969

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"' was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.' In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father's footsteps.

Jan 1, 1939

By Donald W. Gentry

In the mining industry, there are two widely accepted methods of determining the investment worth of a contemplated project. One of these is the payback method and the other is the more recent discounted cash flow (DCF) technique known as the internal rate of return. Both techniques can be useful, but it is important to know the assumptions and characteristics of each procedure and how these may affect an investment decision. The Payback Period-A Shortcut to Yes or No The payback period is simply the time it takes for the cash inflows from an investment to equal that investment. Understandably, projects with short payback periods are preferred to those with longer ones. The payback period may be measured either from the time the initial investment is made or from the time that it begins to yield positive cash flows, but the latter approach is more realistic because it permits more accurate allowance for lost interest on the invested capital.

Jan 1, 1971

By P. R. Kneitz, G. Yoshikado, D. Zayakov

The design and analysis of a circular, domed powerhouse for Pacific Gas and Electric (PG&E) Company's Kerckhoff 2 Project is described. Exploration, geologic stress determinations, mechanical properties, reinforcement and instrumentation are addressed briefly. The analyses of the circular, domed cavern and the comparison of predicted and field deformations are presented in somewhat more detail. The behavior of the completed powerhouse cavern has been found to be substantially as predicted by the analysis.

Jan 1, 1982

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918

By AIME AIME

WILBER JUDSON is one of that fairly large group of mining engineers that graduated at an Eastern college, worked his way up in various jobs in the West and in the Latin-American countries, and finally came to New York as an administrative officer of a large mining company. Since coming to New York he has been a loyal friend and counselor of the A.I.M.E., and is now serving a second term as one of its Directors, his first term covering the period 1935-1938. Mr. Judson was born in the capital city of Michigan on July 26, 1880. Probably it was his roving spirit rather than professorial urging that was responsible for the fact that four colleges were responsible for his education: Northwestern, University of Michigan, Harvard (S.B., 1901), and the Michigan College of Mines (graduate study). In his first ten years of professional work he might have been found serving as mine foreman at Catamarca in the Argentine, as superintendent of the Inter Ocean mine at Sunshine, Colo.. as foreman for the Cerro Prieto, Magdalena, Sonora, as superintendent of the Hudson Iron Co. in New York, or as manager of the Dolores mine in Chihuahua for the Mines Co. of America, or in Spain, or in Panama.

Jan 1, 1942

By A. E. Wheeler, H. Y. Eagle

The copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minére du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1934

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By E. H. Denny

In the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. Some Instances of Asphyxiation by Gases in Metal Mines The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1940

By E. H. Denny

In the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. Some Instances of Asphyxiation by Gases in Metal Mines The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1940