Search Documents

By R. Bainbridge

THE Consolidated Mining and Smelting CO. of Canada Ltd. has operated a lead smelter at Trail, B. C., for many years. In order to take advantage of metallurgical advances, as well as to improve materials handling methods, this company, commonly known as "Cominco," commenced planning a program of smelter revision and modernization some years ago. The first stage of this program involved the design and construction of a new blast furnace gas cleaning system. The selection of equipment, the design of facilities, and preliminary operating details of this system will be dealt with in this paper. The essential problem was to clean and collect 100 tons of dust daily from 153,000 cfm* (12,225 lb per min) of lead blast furnace gas which varied in temperature from 350º to 1100°F. Because it was desired to collect the dust dry, either a Cottrell or a baghouse cleaning plant was to be selected. Comin-co's many years of experience with both systems provided a background for choosing the most satisfactory installation. All information pertinent to the two methods of dust recovery was carefully investigated, and it was decided to replace the existing equipment with a baghouse. Very briefly, the reasons for this decision were as follows: 1—A baghouse installation would be practical because the SO2 content of the gas was low and corrosion would not be a problem if the baghouse operating temperatures were held sufficiently above the dew point. 2—Variations in the physical characteristics of fume and dust, which are inherent in this blast furnace operation, should not substantially affect the operating efficiency of a baghouse. 3—For the same capital cost, metal losses (stack and water losses) would be appreciably less in a baghouse. 4—A baghouse would be easier to operate, and would not require the use of highly skilled labor. 5—Operating and maintenance costs of a bag-house would be lower. 6—The only available space for reconstruction was relatively small, and not suited to a Cottrell installation. Once the baghouse system was decided upon, detailed design of the installation was begun. Baghouse Design Gas Cooling: Before the required capacity of the baghouse could be determined, the method of cooling the gas to the temperature necessary for bag-house operation had to be chosen. The problem confronting the design engineers was how best to cool 153,000 cfm of gas from a temperature ranging from 350°F to brief peaks of 1100°F, down to 210°F, the maximum safe baghouse inlet temperature. A survey of existing blast furnace gas temperatures in the outlet flue showed that the normal range was as given in Table I. The obvious choices of cooling method were: 1— cool completely by the addition of tempering air; 2—utilize a heat exchanger; 3—cool by radiation; and 4—cool with water spray in conjunction with the admission of tempering air. The advantages and disadvantages of the various cooling methods were: Air Addition: To cool completely by the admission of tempering air involved tremendous volumes, Fig. 1. For example, to cool 1 lb of blast furnace gas at 450°F requires 1.84 lb of air at 80°F or 1.60 lb at 60°F. As it is necessary to design for peak conditions, it can readily be seen that volumes of tempering air in the order of 1,500,000 cfm would have to be handled. Using the normal design figure of 2.5 cu ft per sq ft of bag area, a baghouse installation comprising some 600,000 sq ft of filter cloth would be necessary. Such design requirements would be prohibitive, not only from a standpoint of capital expenditure, but also because of space limitations. Heat Exchanger: The utilization of a heat exchanger was given serious consideration. A horizontal tube unit using air as the medium to cool the required volume of blast furnace gas from 400" to 250°F was investigated. Cooling above 400°F would be done by water spray, and below 250°F by admission of tempering air. The estimated capital cost of such a unit was found to be prohibitive. From an operating standpoint, there was considerable doubt as to whether the soot blowing equipment provided would effectively keep the dust from building up on the tube surface. The performance of heat exchangers operating on dusty gas in other company operations had not been too favorable. Radiation Cooling: Although somewhat cumbersome, gas cooling by radiation from 'trombone' tubes or other similar equipment (cyclones) is employed in many metallurgical operations. Such an installation was also considered. However, calculations showed that an installation much larger than the space available would be required to handle the gas volume involved. For example, to cool 153,000 cfm of blast furnace gas from, say, 600' to 250°F (i.e., remove in the order of 58,500,000 Btu per hr with heat transfer rates varying from 1.1 Btu per sq ft per hr per OF for the higher temperature ranges to 0.88 Btu per sq ft per hr per OF for the lower ranges) would need a cooling area of some 175,000 sq ft.

Jan 1, 1953

By Tegner C. Johnson

Just a few years ago, my company was referred to as the Marion Steam Shovel Company. Though we still make shovels, both two and eight-crawler types, the eight-crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It is popular because it can cope with overburden depths in excess of 100 ft and with blasted sedimentary rock, all at an O & O (ownership and operational) cost of ±10[c] per bank cu yd (bcy).

Jan 10, 1974

By George Otis Smith

A YEAR ago, ,at the Institute's dinner, I closed my A remarks with the words: "The scientist devotes his life to the advancement of learning; the engineer gives his to the advancement of living." May 1 begin tonight where I left off then and speak first of the distinction between science and engineering? This difference is a difference both in purpose and in method: it is the sharp contrast between theory and practice; it marks the broad gap between dream and attainment. Sometimes it happens that the investigator is also the builder and applies what he discovers, yet the distinction between science and engineering serves to point out the broad dependence of the engineer upon his brother the scientist. You remember .the old - saying that "where there is no vision the people perish" translate this into modern experience and we may say that "where there is no science, the engineer fails."

Jan 1, 1929

By Richard W. Brummett, Robert L. Dubms

Located some 180 miles east of Los Angeles in Riverside County, California, the Eagle Mountain mine supplies iron ore concentrates for the Kaiser Steel Corporation steel plant in Fontana, California, and for export to Japan. Although the deposits were first discovered in the early 1890's, no production was realized from the area until 1948 when Kaiser Steel Corporation commenced operations. A part of the large Basin and Range province, the Eagle Mountain area's geologic column comprises a thick series of metasediments resting on Precambrian gneisses and schists that have been intruded by sill-like masses of porphyritic quartz monzonite. The metasediments are composed of three quartzite units that are separated by a schistose meta-arkose and by two ore zones. They have been folded into a large east-west trending anticlinal structure that extends completely across the Eagle Mountains. The iron ore deposits occur in two well-defined horizons in the metasedimentary series, and they are found only along the north limb of the major anticline. Host rocks for the ore zones were a series of limestones and dolomites with associated quartzites. Magnetite plus pyrite comprised the primary mineralization that formed many replacement lenses and stringers of ore within the ore zones. The primary ore has been oxidized to hematite and goethite in a broad zone at higher elevations in the deposits. Hydrothermal alteration formed actinolite- tremolite granofels, local phlogopite, and minor tourmaline in the ore zones. This alteration and the ore deposition seem related to the same magmatic event that formed the porphyritic quartz monzonite intrusion

Jan 1, 1968

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By E. H. Mohr

At the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent, of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to ernploy the present flow sheet when Callow cells were in use, for the reason that unless the great,er part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite contnt of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table conecntrates contained only 6 to 8 per cent'. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. Standard Section equipment With the old flow sheet, a standard section consisted of four ball mills and classifiers, one air. lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

By Larry A. Shiprnan

DEMANDS upon power plants by the war program in 1941 intensified problems of coal utilization. It was an outstanding year in that field. The domestic heating stove witnessed outstanding development; the research folks progressing so rapidly that the design of the "perfect" stove is just around the corner. Use of colored motion pictures in analyzing fuel-bed performances has reached a new high with the colored pictures taken at minute intervals and projected at sixteen frames a second as shown by the Koppers Coal Co. and the Anthracite Institute (on domestic stokers) and the Consolidated Edison Co. (industrial stokers). Continued efforts of this kind will be beneficial in analyzing further some of the "Code for Testing Coal" problems confronting Subcommittee No. 2 of the Joint A. I. M. E. - A. S. M. E. Committees.

Jan 1, 1942

A SELF-RESPECTING miner doesn't wash the cuttin's off his hard hat until he quits his job but, on the other hand, he keeps his lamp clean and a "spot" focus on the work at hand; the former habit is a matter of pride and the latter serves for efficient operation. During 1949, the mining engineer got all the "wet raises" for the problem of cutting costs to meet the drop of metal prices and keeping research work up to schedule when strikes tied up his work were his headaches. We note, not without admiration, that he hasn't washed the muck off his hat in token of surrender but, on the contrary, his light shines bright on the job to be done as can be seen in the following pages. Few people have any conception of how much ore and rock have to be mined and how much sorting it takes to cull a pound of copper from a 1 % ore body. These people would be even more startled to picture the problems faced by the engineer in mining and extracting, profitably, .2 oz of gold from a ton of ore as is done at some of our lode mines. Strikers have sometimes kept our researchers from their pilot plants and research laboratories, but the end of the year shows progress in making ore out of taconite and ferruginous sandstone, with a pilot plant in operation at Aurora, Minn., and plans for one near Birmingham. Unfortunately, it looks as though the mining engineer will have to make John Doe secure in mineral resources in spite of himself. Coal for steel, power, and to warm our homes is still economically possible, in spite of Mr. Lewis, through development of mechanized tools for mining. During the year, the use of continuous mining machines has extended, transport systems are being adopted to keep the ore flowing from the face to the tune of 40 tons per man-shift. Experiments in the gasification of coal are going forward in several places and may eventually extend our fuel reserves by the addition of coal seams now too lean for mining. Liquid fuel from coal, oil shale, or natural gas will become economic when oil consumption exceeds our supply; but, at less than 30 cents a ton direct cost for mining oil shale, the engineer is almost making it competitive under present market conditions. In this age of specialists, the mining engineer is still holding his own as a broad-gauge man. As a matter of fact, he is emerging from a stage of semispecialization as a coal, nonmetallics, or metal mining man to the realization that, with mechanization, mining is fundamentally materials handling whether it is fluorspar, coal, or copper ore. From the coal business come rubber-tired mechanical loaders to the iron mines of Birmingham. Shuttle cars are also finding application in the lead mines of the Tri-State. Open-pit methods are universal. Belt conveyors, trucks, Diesels, and mobile, jumbomounted drills are finding application in all types of mining. In preparation, such methods as flotation,- heavy density, electrical, and centrifugal are finding application in coal, nonmetallics, and metals. These concepts have been recognized by the mining engineer who has kept himself informed and has been quick to seize a method, machine, or a process from another operation and, with ingenuity, applied it to his problems. This, our Annual Review issue, is written by mining engineers. In gathering these separate articles under one cover for publication, we think of it as a trrbute to the tireless energy and skill of these men. They get little of the publicity accorded physicists, medical men, labor leaders, or company executives, but they supply raw materials without which industry would die.

Jan 1, 1950

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristics of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economi-cally sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydro-carbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates .3 Improved methods for refining lubricating oils from crude residua,4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessi-tates an appreciable expenditure for equipment as well as added manufac-turing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By Claude P. Heiner

mountain region to M tht Coast points for domestic consumption and for export are shown in Table 11. There is considerable disparity in rates from both Rock Springs, Wyo., and Castle Gate, Utah, to the four coast cities where the slack coal is to be used for purposes other than export. The rate on coal to be exported is the same from either starting point to any of the four coast cities even though there is a difference of as much as 341 miles in the shipping distance. It is interesting to note that the freight rate between Sunnyside, Utah, and Fontana, Calif., on coking coal is $5.05 per ton and that coal up to 8 in. can be moved on this rate if it is suitable for coking. This rate was published late in 1942 on a contemplated annual movement of more than 500,000 tons. There have been decreases in freight rates since 1923 on movements of slack coal from Utah into Seattle and Portland due to pressure on the railroads and to greater. quantity of coal shipped. It is the author,', opinion that a movement of slack coal in excess of 3 million tons of coal per year from Utah to any point in central California would justify a freight rate equal to that puhlished for Fontana, Calif.. or $5.05 per ton. The movement of 3 1/2 million tons of coal per year on the basis of 240 mine working days per year would require that 14,600 tons be handled each mine working day. If it is assumed that shipments could be arranged for a 6-day week, the average railway movement would he 11,200 tons, or approximately 3 trains containing fifty-five 70-ton coal cars per day. Such movements of coal would require railroad equipment represented by the investment amounts stated in Table 12 and entail the services of 250 men. Table 12 ... Railroad Equipment and Investment Required To Move 11,200 Tons of Coal a Day from Utah to California Railroad Equipment Cost 2800. 70-ton coal cara at $6.000 each $16,800.000 32 locomotives at $310.000 each. 9.920.000 Miscellaneous eauiument:.......... .5;000:000 Total........................ $31,720,000 It therefore appears that, under presently known mining methods, the lowest price at which coal could be sold f.0.b. the mine in amounts of 3 1/2 million tons per year for generation of power in central California would be $4.60. It also appears that the lowest freight rate that could be expecled between intermountain points and the central California area would be $5.05 per ton, making a total cost of coal delivered at a plant site of $9.65 per ton. Conelusions The following are the author's conclusions: 1. Coal mines in Utah and in the Kemmerer and Rock Springs districts of Wyoming could increase annual production by 6 1/2 million tons per year. 2. Under present conditions coal could probably be delivered to any steam electric plant in central California at a price not to exceed $9.65 per ton. 3. The use of coal at such a price, while higher than the equivalent present price of fuel oil, is entirely feasible. 4. There are adequate railroad facilities for movements of large quantities of coal from the intermountain region to the Rest Coast. 5. In a national emergency it probably would be extremely difficult, if not impossible, to obtain sufficient oil to meet requirements of the greatly expanded West Coast steam electric generatsing capacity. 6. The intermountain region contains ample coal reserves to supply all conceivable demands for West Coast power generation for a number of generations. 7. Increasing demands of labor threaten to lessen, if not eliminate, savings in cost of coal production through the use of new mining machinery. 8. Continuation of experiments in socialism by the Federal Government through construction of hydroelectric generating plants, particularly those unrelated to land-use reclamation, defies justification. Rates under this concept of a governmental function are subsidized through greater taxation of its people. Private capital is available to construct steam plants, or hydro plants where feasible, and should be permitted to continue in order to preserve the principles of our free enterprise system. DISCUSSION (L. C. McCabe and Robert P. Koenig, presiding) C. C;. BALl*—I was asked to lead off the discussion, but it is not with the thought that I might be able to add anything to the paper. The thoroughness with which it was prepared rather forestalls the asking of many questions. Your treatment, Mr. Heiner, is a very valuable contribution. I do want to suggest—that although you have limited your study to this specific question, with certain geographic limitations, many of the things in your paper apply just as well to the eastern coals. I want to agree 100 pct with your final conclusion concerning government-subsidized construction. Id. C. McCabe*—It is certainly worthwhile to take stock occasionally to see where we are going in problems of this nature. I agree with Mr. Heiner that ultimately the only reliable source of fuel that the West Coast has is coal hut the time factor is the difficult element to evaluate. Just before I came here I discussed this subject with N. B. Hinson, Vice President and Executixe Engineer of the Southern California Edison Company, and Chairman of the West Coast Inter-Power Exchange Committee. He has given much thought to utilities' fuel supply and it was very helpful to me in preparing a discussion of the paper to talk with him beforehand. Stock taking and forecasting of future development are essential to the continuing success of any enterprise. Mr. Heiner has called attention to the unprecedented growth of central and southern California and to the increased demands for fuel and power which have accompanied it. He discusses the increased fuel oil and natural gas requirements and the probable limits on the future use of these fuels and of hydroelectric power. In contrast to the calculable limits of these sources of electric energy, the author points to the availability of enormous reserves of coal in the Rocky Mountain States adjacent to the Pacific Coast which can be utilized for power generation. That there will be increased use of coal for power generation in the area under discussion is generally accepted hut it is in the timetable of such development that there is not complete agreement. In a recent report, Mr. Hinson reviewed the future power outlook for the Pacific southwest area. He pointed out that the use of steam plants in connection with water power plants in this region has made the maximum use of hydroelectric energy possible, and that the correct balance between hydro and steam generating plants produces the most economical overall system. Steam plants in the area which had been installed to protect against deficiency in hydro energy in dry years were used to carry war loads. Fortunately, no dry

Jan 1, 1950

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles. The first commercial unit employing the new thermoadhesive method of dry separation of minerals was installed at the Detroit mine of International Salt Company in Detroit, Mich. (Fig. l). This unit was first put into operation in March 1957. The purpose of the Detroit installation was 1) to serve as a pilot plant for evaluating the process on a commercial scale and 2) to produce marketable quantities of rock salt of improved quality and ap- pearance. The design of this plant was based on the results and information obtained from a 1-tph pilot plant at Battelle Memorial Institute. DESCRIPTION OF PLANT Location: The separation plant was installed underground near the crushing and screening plant, for this was the most suitable location from the standpoint of material handling. Furthermore, ample space was availabe at this location. Because the process requires a relatively constant temperature, the uniform year-around temperature of the mine (57°F) gave an added advantage to an underground operation. Feeding: The rock salt is conveyed to a surge bin, from which it is fed to the heating unit by a conveyor. The feed-rate control consists simply of an adjustable gate at the bottom of the surge bin. The plant may be fed either No. 1 grade of rock salt (0.279 to 0.375 in.) or No. 2 grade (0.375 to 0.500 in.) with a maximum input capacity of 500 tons per 15-hour day. Heating Unit: The heating unit (Fig. 2) consists of a panel of infrared lamps suspended inside a low-speed revolving screen. The radiant-heat panel, which is curved for most effective utilization of the heat, holds 240 infrared lamps of standard industrial type, each rated at 500 watts. The position of the panel is adjustable so that it can be placed centrally over and to within 6 in. of the salt bed on the screen. The entire heat panel is suspended by rollers in ¦ R. J. Brison and O. F. Tangel: Development of a Thermo-adhesive Method for Dry Separation of Minerals.

Jan 1, 1961

By Thomas L. Kesler

I all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ocmulgee and Oconee rivers drain the area. They and their main tributaries have flat, swampy floodplains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirque-like heads. Gullying and under-cutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level, and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig. 1. The division between the Coastal Plain and the Piedmont plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward-sloping surface of the crystalline rocks of the Piedmont. Cretaceous Host Formation The kaolin deposits, which are described in the succeeding section, occur sporadically in lenslike bodies in a thick series of poorly sorted clayey sands constituting the lowermost of the Upper Cretaceous formations, the Tuscaloosa. The basis for this correlation has been reviewed by Cooke.1 The same formation has been termed the Potomac group by Ladd2 and the Middendorf formation by Smith' in reports on the kaolin deposits. In another report, Veatch4 called the formation the Tuscaloosa but correlated it with the Lower Cretaceous. The Tuscaloosa in this area consists of fine to very coarse sands, commonly cross-bedded, which contain widely different proportions of white, pink, and yellow kaolin and considerable white mica. A few of the coarser beds contain quartz grains up to 3 in. in length, with bodies of pure white kaolin of equal size that appear to have been formed by the weathering of feldspar grains in place. In the kaolin-producing area, gravel and cobbles occur mainly at the base of the formation. Fig. 2 shows the relations of the Tuscaloosa and its kaolin deposits to the adjacent formations. Its base, on the eroded surface of the crystalline rocks, dips southeastward 50 to 60 ft to the mile, according to LaMoreaux.5 The upper surface of the Tuscaloosa is also an unconformity,

Jan 1, 1952

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered arc' those circumstances under which any company, including one that is cash rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON INVESTABLE CASH If you approach an individual with an investment which can be financed from savings, or by borrowing at a rate higher than one is earning on savings, that individual will quickly tell you that to pay interest at a rate higher than is being earned on savings would reduce overall income. Assuming that additional investment opportunities are not currently being considered, the individual concludes that a draw-down on savings, leaving a cushion for contingencies suited to individual circumstances, is the correct financial decision. For reasons discussed later, the simple mathematical logic leading to this conclusion tends to become obscured at the corporate level. When Leveraged Studies Are Inappropriate or Premature Surprisingly, I have heard of a number of companies that could afford to finance an investment solely with internal funds, which have made DCFROR (i.e. discounted-cash-flow rate-of-return) studies not only on a 100% equity basis but also on a leveraged basis. Certainly, a leveraged study would be appropriate if additional projects were competing for more capital than was available internally. Often, however, other projects are not far enough along to warrant a leveraged study and there is some danger that a project may be undertaken because it has an estimated acceptable rate of return, on a leveraged basis, that is not ultimately earned because some of the other projects are postponed or abandoned and borrowing is less than expected. For the above reasons, until it has been determined that (1) borrowing is a reasonable certainty for a particular project and (2) the timing and amount to be borrowed has been determined within a reasonable range of accuracy, I believe it is inappropriate and misleading to calculate DCFROR for a project other than on a 100% equity basis. Even when there are several projects currently competing for funds and borrowing will be required to finance one or more of them, using the common yardstick of calculating DCFROR on a 100% equity basis is a safer method to initially evaluate and compare the attractiveness of the projects. Many companies, whether they would have to borrow or not, will reject projects that on a 100% equity basis do not meet their minimum rate of return standards. Some companies which have to borrow will undertake a project provided the project's DCFROR on a leveraged basis meets its minimum return standards. The danger of this approach is that even moderate shrinkages of estimated cash flows could plunge return below

Jan 1, 1985

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with the problems associated with the contamination of air and water from coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration to specific area should begin early before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants and advance consideration should be given to all the problems concerned with contaminants. The first part of the chapter will concern itself mainly with the contamination aspects of fine-coal cleaning and "black-water" disposal. Also attention will be given to the nature and formation of water from coal-mine drainage systems and the treatment of these waters for industrial use. Some attention will be devoted to the cost of installing and operating the various beneficiation systems for the removal of suspended solids. The second part of the chapter will analyze the problems of air contaminants from coal preparation plants. The nature and the effects of these contaminants and their potential for air pollution will be examined. One of the most critical is the measurement and analysis of these contaminants. As a result of identifying and determining the extent of the problem, better control can be planned. One of the most serious contaminants in air involves the element sulfur, and its elimination as a source of air pollution is one of the most challenging areas in coal preparation today. The last part of the chapter will emphasize the long-range problem of refuse disposal and control. Minimum operating and maintenance costs are functions of the proper selection and geometry of refuse disposal areas. Disposal procedures are varied but must be rigidly pursued or difficulties will result. Maintenance of refuse areas, including monitoring of burning refuse, is critical. It should be recognized that fine-solid refuse disposal systems must be carefully designed to minimize contamination. WATER CONTAMINANTS FROM PREPARATION PLANTS Pollution Aspects of Fine-Coal Cleaning and "Black-Water" Disposal The effluents from coal washeries and waters draining from plant-site surfaces inevitably contain fine coal and coal refuse materials in suspen-

Jan 1, 1968

By G. A. Vissac

MOISTURE in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain").

Jan 1, 1949

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement' affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) THE term "pipe-vein" has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions : (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term "pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1878

By Emery R. Hayhurst

SILICOSIS has been described in a report of the American Public Health Association as a disease due to breathing air containing silica, characterized anatomically by generalized fibrotic changes and the development of miliary nodulations in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for work, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray findings. ... The disease is divided arbitrarily into first, second, and third stages for convenience of description and possible compensation purposes. At least two distinct types of silicosis are recognized, acute and chronic. The acute form was reported as early as 1713, when a British patent for grinding flint by wet methods was granted because the dry powdered material "proved very destructive to mankind, so much that any person, ever so healthful, working in that business cannot possibly survive over two years."

Jan 1, 1936

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930