Search Documents

By E. S. Bardwell, R. J. Lapee

Twenty years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute,' discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 Ib. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness. Method of Purification Briefly, the method adopted for purifying tank-room electrolyte at Great Falls has been as follows: Each day a certain volume of tank-room electrolyte is run off and sent to the purification plant, where it is boiled down to approximately 46' 136. The concentrated electrolyte is then sent to crystallizing tanks where the bulk of the copper is crystallized out as copper sulfate. The mother liquor is then passed through insoluble anode tanks to remove the last of the copper and most of the arsenic and antimony. It is then either returned to the tank room direct or boiled down to 55' Bé, the iron and nickel salts crystallized out and the mother liquor returned to the tank-room circuit as restored acid. Prior to 1930 all of the evaporating was done in lead-lined tanks 13 ft. in diameter by 4.5 ft. deep, provided with lead heating coils through which steam at 30 lb. gage pressure was circulated.

Jan 1, 1934

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By Arnold S. Epstein

Tlze green electroluminescence occurring at liquid-nitvogen temperature in epitaxial gallium phosphide diodes is exarnined using the donor dopants silicon and sulfur. Zinc is used as the p-type diffusant. Two tt~ain peaks are found, namely til 0.56 and 0.535 p. The intensity of the gYeen peak occurring at 0.56 is found to oary as -4"' wlzere Jf is the forward current density and to first order appears to be dependent on the concet~tvation of ionized donovs. Tile vadintive lifetinze fov this process is -10-'sec. The intensity of the 0.56-p lu~ninescence is nt least several ovdevs of magnitude greate,, at liquid-nitvogen temperature than that noted jor the 0.538 radiation for current densities up to about 35 amp per sq cm. The variation oj- the intensity of. the 0.538-p peak with current density caries according to the donor dopant. With sulfur as the donor one has a J12 dependence, whereas when silicon is the donov a J1.5 dependence is noted. Tl~e above can be fitted to a In molecular process (in first order) such as a band to band recombination. The constant B fir band to band vecombination) is found from our experitt~etlt to be of the order of 2 CZI cm per sec, zcl~ereas for tlze impurity vecombination peak (0.56 p]) tile A cotzstor~t is of the order of. 7 x 10-' cu cm per sec. The structuve o/. the diodes at liquid-nitvog-en tett~peruture is oj tlze double injection type, and by carefi~lly selecting. the thickness of the structure one can regulate the onset of the 0.538-p radiation. The diode clzavaclevistics follow an I-Vx laiv where x is >1. Llregatiue resistance in these structures con be correlated with saturation of tlze 0.56- peak. ThE development of high-purity, large single crystals of epitaxially grown gallium phosphide is the ultimate aim of the studies to be reported. While a number of papers and reviews' have been presented on properties of gallium phosphide grown from gallium solution and from the melt, less attention has been paid to the properties of epitaxial gallium phosphide grown from the vapor. In the studies to be reported we have examined the effects of shallow donor impurities, primarily silicon and sulfur, at liquid-nitrogen temperature, on both the electrical and green electroluminescent properties of carefully characterized single-crystal epitaxial Gap. I) EXPERIMENTAL PROCEDURES A) Material Preparation and Properties. The samules used in this investigation were single-crystal n-type epitaxial gallium phosphide. he single crystals were synthesized from the elements by vapor transport and epitaxial deposition on single-crystal gallium arsenide substrates. Typical transport agents used were chlorides. The growth procedures are described in more detail in Ref. 2. The samples were grown in the (111) orientation and had thicknesses up to 480 . Following the growth, the GaAs substrate was removed from the epitaxial Gap by etching in nitric acid. The Hall effect and resistivity of these n-type samples were measured as a function of temperature and analyzed for impurity content and compared with spectroscopic emission analysis. The results are given in greater detail in Ref. 3 but a summary is noted in Table I. In Table I, AED denotes the donor ionization energy, Nd is the donor impurity concentration, lvA is the acceptor impurity concentration, NI is the total impurity concentration, Rip vs temperature is the measured Hall mobility-temperature relationship from liquid nitrogen to about 400"K, n(77"K) is the measured carrier concentration at liquid nitrogen, and R/p(77'~) is the measured Hall mobility at liquid nitrogen. Good agreement is noted between electrical and emission analysis for the major donor impurity, silicon, in the two materials where it is a major constituent. In the case of the two samples SC90-6 and AP138-3(111) B which were sulfur-doped the ionization energy found from the electrical data is in good agreement with that reported for sulfur.4 The acceptor impurities are not known, although from the presence of magnesium in the samples as indicated by emission analysis and its known role as an acceptor in GaP,4 magnesium could be present as an acceptor. Similarly, since silicon is known to be an amphoteric impurity4 it may also be present as an acceptor in the Gap.* The *A small band has been noted at 0.625 11 in samples SC90-6, SC76-4, and SC77-4, suggesting according to Ref. 5 that sillcon could be present as an acceptor In these samples since these authors have found this peak to represent a donor-silicon emission. presence of calcium deduced from emission analysis is not correlatable with the electrical analysis and its presence as an electrically active impurity should be questioned. B) Sample Preparation and Diode Fabrication. The original slices were of the order of 2 sq cm in area witi the (111)B face up. The material was cleaved and sectioned and the best pieces selected (i.e., those which visually appeared to have the least strain and defects). The samples were polished, lightly etched, and cleaned in trichloroethylene. Zinc was diffused in a closed tube at 800°C to form a p-n junction. Diodes were made from these samples. The depth of junction varied, but did not exceed 10 p depth. The back side of the slice was lapped back and a low-resistance n-type contact was formed (at 600°C in forming gas) to an Au-Mo tab with a hole in the middle for

Jan 1, 1968

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-'. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.' Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.' In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give there full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: -

Jan 6, 1915

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By John B. Hastings

Ten miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake-beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; bat this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. This section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September

Jan 1, 1909

By AIME AIME

AN ENGINEER with as varied geographical experience as H. J. Brown does not often specialize on one particular thing all of his professional life. For forty years he has been engaged in gypsum mining, manufacturing, plant design, construction, and operation. Not only is it his work, but he says it is his hobby as well, though membership in three yacht clubs might belie that statement. New England's new representative on the A.I.M.E. Directorate, who was born in New York, Dec. 20, 1879, went to the Lawrence Scientific School at Harvard at the turn of the century. He tried journalism for a year, with the Boston News Bureau and associated financial

Jan 1, 1940

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By C. Chiou, D. P. Seraphim

The effect of clustering on the superconducting properties of Al-Zn alloys has been studied by the ballistic induction techniques. The superconducting critical temperature, T,, changes when zinc-rich clusters are formed. The change in T, depends on the concentration and may be positive or negative, but always correlates with an effective decrease in the solute concentration of the alloy. Reversion after clustering effectively returns a 5 at. pct Zn alloy to the quenched state. These methods might be use&lly extended to the Al-Mg system, where X-ray data are difficult to obtain. In very dilute Al-Zn alloys, as in other tin,' indium, aluminum,2 or tantalums base solid solutions, there is a decrease in the superconducting critical temperature, Tc, roughly proportional to the temperature independent resistivity, i.e., -0.2°K per pS2cm. With increasing solute concentration, the T, generally reaches a minimum and then increases4 to a value well above that for the pure solvent. The change of T, with solute concentration follows an empirical formulation involving two constants which correlate with the scattering cross section of the impurities. As will be shown below, the Al-Zn alloys more concentrated than 1or2at. pct do not follow the empiricism, probably because they are unstable even when rapidly quenched.5 However, it seems possible to study at least the later stages of solute clustering by precise measurements of the 1', following various thermal treatments. A few experiments on quenched alloys, aged alloys, and tests on reversion are reported here. The heat treatments selected for obtaining the quenched and aged states were mainly deduced from the work of Dash and Fine.6 For the quenched state, specimens were homogenized at 480°C, quenched to -160°C, and immediately transferred and mounted in liquid nitrogen. Measurements on the superconducting properties and residual resistivities were then made at helium temperatures, after which the specimens were aged at room temperature for 3 to 5 hr, i.e., much longer than the time required for clustering to be essentially completed. The superconducting properties and residual resistivities were once again examined. To reach the reverted state of the A1-5at. pct Zn alloy, the aged specimen was heated for 5 min at 200°C and then tested as above.

Jan 1, 1963

By Lucien Eaton

The use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material must be used. In different parts of the world sand, clay, gravel, culm, granulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, but to describe some of the methods used for placing sand fill and to make a brief comparison of their merits. Methods of Placing Sand Sand may be transported and placed underground by several methods, which may be classified as follows: 1. By Hand.—The sand, which must be comparatively dry, is taken down the shaft in cars on cages and is distributed to its destination in these cars, or it is dumped down raises and is drawn off and distributed by means of cars, wheelbarrows or scrapers.

Jan 1, 1932

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By AIME AIME

THE meeting" of the Rare Minerals and Metals Committee was held Monday afternoon, Feb. 17; Donald M. Lidclell, chairman, presiding. The first paper (T. P. 279), "Progress in the Use of Tantalum," by George W. Sears, was read by Mr. Smyth. Dr. Sears' paper contains an interesting summary of the uses, alloys and ores of tantalum and a resume of present method of reduction. The uses of tantalum is based on its extreme rise to the reaction of even the strong mineral acids, its great avidity for the common gases and its capacity for transforming alternating to direct current. Tantalum, as an alloy material, has received considerable study and many alloys have been reported. Among them three types appear to .be most prominent, alloys of high melting point, hard alloys and acid rising alloys. As the estimated quantity of tantalum in the earth's crust is less than that of gold, it must be looked upon as n rare metal. Australia is the greatest producer and the Black Hills of South Dakota produce minor amounts. As the one type of mineral available contains both tantalum and columbium, the extracting and metallurgy of tantalum are difficult chemical processes. Greater simplicity in this and the development of a market for columbium would undoubtedly be of great benefit to the tantalum industry, andl make for a greater use of tantalum produced.

Jan 1, 1930

By A. E. Bellis

The time effect in reheating certain steels below the critical range is very marked. The increased toughness, shock-resisting power, and machinability of steel subjected to a long, high drawing temperature has been thoroughly demonstrated and is of practical importance, particularly in the manufacture of "smokeless" rifle-barrel steel. The time effect in tempering is most important when a maximum drawing effect is desired, in which case the highest physical properties as well as ease of machining are important considerations. These are the conditions in drilling a rifle barrel. A hole, 0.30 in. in diameter and 24 in. long for the Springfield rifle, and 30 in. long for the Russian military rifle, has to be drilled in the heat-treated material. This barrel-drilling operation is probably the most difficult one in rifle manufacture, and anyone who has been connected with rifle manufacture knows how seriously production is affected when "hard" or non-uniform steel for barrels is encountered. The importance of high physical properties (tensile strength, toughness and resilience) in a rifle barrel is obvious. The physical properties of two different lots of barrel steel are given below. The first lot, No. 1, gave serious trouble in the drilling operation; the second gave no trouble at all.

Jan 2, 1918

By Bryan J. Travis, Thomas L. Cook

INTRODUCTION Our growing concern for adequate and secure sources of energy and minerals has stimulated vigorous exploration for new sources, research toward a better understanding of geological processes, and development of new extraction technologies. The need for control, or at least prediction, of subsurface fluid flow is important for many of these technologies for example: primary, secondary and tertiary recovery of oil; ground water and waste management; in-situ fossil energy extraction (oil shale, coal, tar sands); and solution mining of uranium, copper and other minerals. These technologies, especially the last two, are characterized by highly complex systems. A partial list of the physical processes occurring would include flow in porous/fractured media, multi-phase and multi-component flow with heat transport, chemically active fluids and soils, tracers, diffusion and dispersion, fracturing and dissolution. A great deal of understanding of how these processes behave and interact can be obtained from models. MODELS Theoretical models are valuable because they: 1) provide a frame of reference for interpreting results of laboratory and field experiments; 2) once validated by experiments, allow a variety of geometries, injection/production strategies, etc., to be examined (at relatively low cost) for efficiency and stability; 3) can provide guidance to the design of experiments and field operations. Most models are based on the fundamental principles of mass, momentum and energy balance. But from this starting point, many paths can be taken. For example, there is the theory of Payatakes (1973) which concentrates on the microscale dynamics. In this approach, the rock or soil matrix is represented by a complex of characteristic channels (such as periodically constricted smooth tubes). Detail of flow within the characteristic channel is calculated very accurately. A difficulty with this model is that description of a representative channel can require several parameters which may not be easily measured. Also, it is not clear how the channels can be combined practically to model a large scale flow. Another type of model is the "global" one described by Bear (1972). Here, the continuum equations for conservation of mass, momentum and energy are averaged over a distribution of pore channels, resulting in a set of conservation equations in which the small scale structure of the medium is replaced by quantities such as porosity, permeability, dispersion coefficients and tortuosity. This approach allows computation of large scale flows. However, additional constitutive equations are needed which relate averaged quantities such as permeability to observables such as local saturation, particle size distributions, and others. An important difference between models is the way they handle the momentum equation. Payatakes' model solves the full equation. In others, it is replaced by a simpler relation such as Darcy's law (valid for slow flow rates) or by Forchheimer's equation which extends Darcy's law to higher flow rates. These simple relations can nevertheless match a great deal of experimental data (Dullien 1975). The permeability term which appears in Darcy's law and in Forchheimer's expression has been related to other quantities such as porosity and particle surface area. The Kozeny-Carmen equation is a well-known example, valid for some ranges of porosity and particle sizes and for some materials. Several other semi-theoretical, semi-empirical formulations have been devised, none of which are entirely satisfactory. One goal of researchers has been the ability to predict permeability of a porous material from basic measurable quantities such as grain size distributions without recourse to adjustable parameters. This effort has proceeded from consideration of distributions of idealized, non-intersecting channels, to intersecting channels, to consideration of both distributed pore radii and pore neck radii. This last approach has been used successfully to predict permeabilities (ranging over several orders of magnitude) in sandstones (Dullien 1975). Additionally, studies on explicit networks of channels (e.g., Fatt 1956) and percolation theory (e.g., Larson et. al. 1981) have been used to examine interconnectivity effects in porous media with the hope of eventually being able to predict permeability accurately. To be of more than theoretical interest, a model must be compared s controlled laboratory conditions where boundary and initial conditions and relevant material properties can be accurately determined. Also, extraneous forces can be eliminated so that the interactions between processes of interest can be clearly seen and flow models can be vigorously tested. In contrast to the well-defined environment and

Jan 1, 1982

By H. J. Hager

The Alabama By-Products Corp. is an entirely independent Alabama enterprise. Organization of the company stemmed from the consolidation of three important properties in the Birmingham District and a by-product coke plant at Tarrant, Ala. In 1924 ABC was merged with the Pratt Consolidated Coal Co. This merger greatly extended the company's holdings of valuable coal lands in Walker and Jefferson Counties.

Jan 12, 1950