Search Documents

By W. V. Long, D. H. Reynolds, R. B. Bhappu

Equilibrium distribution coefficients were determined for some monovalent and polyvalent ions for several absorbing and exchanging media as functions of pH and initial ion concentration. Among ions studied were NH4 (I), K(I), Ni(II), Ce(III), Th(IV), and Mo(VI). Absorbents used were: ion exchange resins; a tertiary, and a quaternary amine in an inert solvent; and some activated carbons. The ions studied were in aqueous HCI, HNO3, H2SO4, or HC104 solutions. The classical mass action expression proved of little value in describing the variations observed. The data indicate that the determining factors in absorption and ion exchange may be the ionic species in the aqueous solution, which in turn depend upon pH, dilution, and perhaps other conditions. Three sorption processes have become prominent in recovering values from leach solutions. These are: 1) ion exchange, 2) solvent extraction (liquid ion exchange), and 3) physical adsorption by materials of high specific surface. In the first two of these processes the exchange reaction is considered chemical in nature, and is discussed in terms of the mass action principle. The third is considered a surface phenomenon and is discussed in terms of surface areas and various forms (Gouy, Stern, Grahame, etc.) of the Helmholtz double-layer theory. Generally speaking, we have found in chemical analysis and hydrometallurgical studies that there are close similarities between the three sorption processes, and also differences which are difficult to reconcile with any of the usual theoretical treatments. That others have experienced the same troubles is shown by the fact that usable processes, in chemical analysis as well as in hydrometallurgy, generally are discovered by empirical procedures. EXPERIMENTAL CONSlDERATlONS The gaps between theory and practice have allowed many conflicting statements to appear in the litera- ture. To learn, in particular, the behavior of some metallic ions on a cation exchange resin at a constant pH, equilibration studies were made over a wide range of concentrations.' Results are shown in Fig. 1 for four metals in hydrochloric acid solution on a strongly acidic cation exchange resin, AG 50W-X8 (Bio-Rad). The distribution coefficient, defined as D = amount of metal extracted per g of resin/amount of metal unextracted per ml of solution is seen to vary in a way to support all manner of reports about its behavior with changes in solution concentration. The metals used were chosen from those least likely to form stable chloro-complexes. The changes of slope in the various isotherms may reflect formation of unsuspected chloro-complexes of low stability (ion-pairing for example) whose concen-

Jan 1, 1967

By T. P. Floridis

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper' reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.' This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.' The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work' is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By P. Somasundaran, I. J. Lin

There are several methods described in the literature for the determination of the order and the rate constant for the flotation of minerals. These often involve some type of computational or graphical procedures. A relatively simpler method developed on the basis of a technique used by Chang" in chemical kinetics is described in this paper. Chang's technique, like most others in chemical kinetics," is based on the law of mass action which states that the rate of a chemical reaction is proportional to the active masses of the reacting substances at any given time. Application of this law to the flotation of minerals would involve the adaptation of the terms "flotation" for "chemical reaction" and "floatable amount of the minerals" for "the active masses of the chemical reactants." There are indeed a large number of physical processes controlling the actual flotation rate. The most inefficient one of these could be considered equivalent to the slowest reaction in a series of chemical reactions. If variables such as aeration rate and agitation are kept at constant levels, the rate of flotation under free flotation conditions (i.e., conditions under which the suspension is dilute) will be given by the following equation: where C is the concentration of the floatable minerals in the pulp at any given time t, K is the rate constant, and n is the order of the reaction. If we represent the floated fraction of the floatable mineral at time t as m (0 m - 1) and C at t = 0 as Ca, integration of Eq. 1 yields

Jan 1, 1974

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H20, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H20, FeO¬Fe-CO-C02 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By Charles Smeal, Robert J. Schafer, Max Quantinetz

Normally metal powders cannot be ground to sub-micron sizes because of welding and agglomeration phenomena. Through the use of selected grinding aids and grinding fluids, nickel and other metal powders have been ball-milled as fine as 0.1 It was found that certain inorganic salts are more effective grinding aids for metal powders than conventionally used surfactants. METAL and alloy powders are used to produce reagents, pigments, coatings, solders, brazes, and parts for industry by powder metallurgy techniques. They are also combined with refractory compounds to produce cermets and dispersion-hardened products. One of the interests at the Lewis Research Center has been to explore the potentialities of the dispersion strengthening process. Since the work of Ir-mann, many investigators have shown that the strength of dispersion-hardened products may increase with decreasing interparticle spacing.24 One approach to achieving small interparticle spacing is to combine fine refractory compounds and metal powders, preferably below 1 in size. In attempting to obtain fine metal powders, it was found that until very recently the best that could be obtained from commercial suppliers, particularly of ductile metals, was about 1.0 . Interest was therefore developed in providing finer metal powders for dispersion-hardening studies. Information obtained from the literature, from others working in the field, and from prior experimental work performed at NASA, led to a consideration of ball-milling as a technique to produce the desired materials. Some of the variables associated with ball-milling are the size, material, and nature of construction of the grinding container; the nature and amount of the grinding material and material to be ground; and the nature and amount of the grinding liquid and grinding aid, if employed, and the grinding time. In all ball-milling, welding and agglomeration can oc- cur as well as grinding. Because of the tendency of ductile metals to weld together, they are difficult to grind.5 The ultimate particle size obtained on grinding is generally the one at which the rate of grinding becomes equal to the rate of welding. To help delay welding and thus obtain smaller particle sizes, grinding aids are often employed. The principal objective of this investigation was to produce submicron metal powders by ball-milling the powders with selected grinding aids and grinding fluids. A secondary objective has been to attempt to explain the variations observed in grinding behavior by considering possible grinding mechanisms and correlating various parameters with grinding effectiveness. Three groups of ball-milling experiments were run; one in which the grinding aid was varied, a second in which the grinding fluid was varied, and a third in which the material being ground was varied MATERIALS, APPARATUS, AND PROCEDURE In the first group of experiments in which the grinding aid was varied Inco Carbonyl Grade B nickel powder initially 2.5 (all sizes refer to average particle size as measured by Fisher Sub -sieve Sizer) was used as the material being ground and 200-proof ethyl-alcohol as the grinding fluid. Surfactants, representative of typical organic structures, were selected as grinding aids. Inorganic salts used as grinding aids were chosen on the basis of the size and valence of their ions. Water soluble salts were used in order to facilitate their removal from the slurry after grinding. In the second set of experiments, grinding of the 2.5- Ni powder was tried in four different grinding liquids; water, cyclohexane, n -heptane, and methy-lene chloride. In this study seven grinding aids selected from those tried in the first group of experiments were employed. In the third group of experiments 200-proof ethyl alcohol was again used as the grinding fluid to mill Cu, Cr, Fe, Ag, and Ni powders of various initial particle sizes' All mill charges contained 300 ml of grinding liquid and 3000 g of 1/2 in. stainless steel balls. When inorganic salts were used as the grinding aid, 70 g of salt and 210 g of metal powder were employed, and with surfactants 6 g of grinding aid and 300 g of

Jan 1, 1962

By A. S. Yue

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By R. B. Gordon, D. A. Koss

Ultrasonic-atlenuation changes due to the formation of free dislocations have been observed during tensile tests of magnesium and LiF single crystals and samples of polycrystalline Results on the LiF and samples are similar: A preyield attenzration increase is observed which, however, be-corlzes smaller as the magnitude of the drop in load al yielding increases. This indicates that the yield point observed in these materials is due to dislovation rather than dislocation unpinning and that the initial density ' free dislocations must be low if the yield point is to be sharp,. Tests on the magnesium ere conducted at both 27" and 200C. Magnesium has the unusual property that the yield drop is larger at the higher test temperature and is accomplished by a decrease in attenuation. The latter is due principally to the temprovary pinning of detained dislocations by highly solute atoms. After strain aging., a stress as low as 0.3 bur suffices to unpin dislocations; microstrain measuements of sufficient sensitivity should. reveal plastic flow at stress levels this low IN another paper,' we describe the technique of simultaneously observing ultrasonic-attenuation changes and plastic microstrain during deformation of spher-oidized carbon steels. Changes of ultrasonic attenuation indicate damping effects caused by the oscillation of long, freely moving dislocation segments. Simultaneous microstrain measurements are used to indicate total dislocation motion. The dislocation-damping observations are most useful in the study of the early stages of deformation where the dislocation density is low and the plastic strain is small and relatively difficult to measure. Particularly interesting results are found in materials which display sharp yield points. Observations of these phenomena are reported here for three materials: single-crystal LiF and magnesium, and poly crystalline molybdenum. EXPERIMENTS Dislocation-damping effects were observed by measuring changes in acoustic attenuation with the ultrasonic-pulse method. The end faces of each of the specimens were ground flat and parallel and a quartz 10 Mc per sec, x-cut transducer was attached to one face. The bonding agents used were: a) "Nonaq" stopcock grease with magnesium, b) beeswax with LiF, and c) salol with molybdenum. With the LiF, the best acoustic signals were obtained at 45 and 50 Mc per sec; all other measurements reported are at 10 MC per sec. The Sperry Ultrasonic Attenuation Comparator2 was used to measure attenuation changes. In the

Jan 1, 1967

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By Oswald J. Heinrich

The responsibility resting upon the owners and managers of mines where fire-damp is generated, renders it a matter of imperative duty that a frill and correct statement of any explosion that occurs should be given to the public. But such a statement must be based on the testimony of impartial eye-witnesses or trained experts. Then a sad experience may result in the adoption of effective preventive measures. In the absence of any official and professional body of mining experts in the State of Virginia, the writer desires to submit to his professional brethren of the American Institute of Mining Engineers an account of an explosion which recently took place in a colliery under his management, and earnestly desires a thorough and impartial discussion on the Fats submitted. Description and Plan of the Mine.—The "Grove" shaft is situated at the nearest point 825 feet from the last old workings upon the Midlothian property, south of the old Pump shaft works. (See Plate 111.) The shaft was sunk by the former company, some thirty years ago, to the depth of 622 feet. An incline over 230 feet long, starting in a northwest direction at a depth of 105 feet above the shaft bottom, had been driven to explore the coal on the dip. A return of very small dimensions had been driven round the shaft on the south side, entering the upcast chamber. With the information obtained from the former company that a seam of coal about four feet thick, at a depth of 490 feet, had been found, and with the information obtained by the present proprietor, R. T. Burrows, of Albion, N. Y., by means of two boreholes on the dip west of the old shaft, in both of which workable seams of coal at various depths had been ascertained, the clearing out and thorough retimbering of this shaft were commenced in March, 1873. Borehole No. 1, at a depth of 4773 feet from surface, revealed a seam of coal. This borehole was afterwards carried to a depth of 1140 feet to the granite, without finding any other seam of coal. Borehole No. 3, at a depth of 608 feet, revealed the first coal-seam, 14 1/2 feet thick; at 633 feet, the second, 12 feet thick; at 662 feet the third, 1 foot thick, and at 692 feet the fourth, 43 to 5 feet thick. The borehole was stopped at a depth of 715 1/2 feet.

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By Dr. O’Neil Thomas J., Donald W. Gentry

The greatest of all gifts is the power to estimate things at their true worth. LaRockefoucauld INTRODUCTION The primary reason for performing a feasibility study on a proposed mining venture is to investigate all phases of the proposal in as much detail as necessary to justify either dropping the project or continuing expenditures through the next stage. The economic evaluation component of the feasibility study, therefore, must ultimately be based on information which provides an answer to the question, "What is it going to cost?" Unfortunately engineers preparing feasibility studies never have all the engineering or economic information they would like or need. Consequently, the economic portion of the analysis can only be performed if estimates of the various costs associated with the project are made. Project cost estimates, in turn, require estimates of all the physical factors affecting cost components, including anticipated performance of plant and equipment as well as all pertinent geologic, mineralogic, and metallurgical variables. Before useful cost estimating procedures can be applied considerable data must be collected, compiled, and organized. Preparatory work typically includes organization of cost data available for estimating purposes, development of techniques for updating historical costs, and establishing methods of forecasting prices and costs over the duration of the project. Cost estimates for mining and mineral processing projects involve so many features and variables that it is absolutely essential to have some means by which the vast amount of detail can be organized. It is very important to identify, in as much detail as possible, all the cost data available (historical and developed) to the estimator. These costs, after being properly identified in detail, should be com- piled, stored, updated regularly, and made readily available for use in developing new cost estimates Accessing files of current cost information requires a standardized numerical system of classifying cost data. When uniform definitions and procedures are used, every project record contributes to the common store of estimating data.

Jan 1, 1984

By F. G. Coggin

" If you could only get that motion into a machine," said a gentleman, as he watched the process of making a " van " on a shovel, and saw the copper roll up to the highest point, "it would beat the world for slime-dressing." This idea has led to many an effort to get into a machine that peculiar motion, called the " vanning motion;" and so cams, eccentrics, eccentric gears, levers, bell-cranks, togglejoints, links, springs, etc., have been brought into requisition, while a contribution has been laid upon all the conceivable motions, rolling, tumbling, swinging, jerking, tossing, dropping, tripping, intermittent, regular and irregular, or a combination of some of them, to which have been added percussion, concussion, and more discussion —all in a vain attempt to combine in a single machine the consecutive motions of the shovel, in washing, flowing, and tossing the van. The Patent Office Reports, and the various mills of the country, show, as a result of this, a lot of gimeracks, most of which never went beyond a first trial, finding their way to the scrap-heap. Others still running might as well be there; while some have considerable merit for dressing other and richer sands than copper. It does look tempting to see that clean edge of copper climbing up the shovel-blade; but those who have seen in it such visions of large fortunes have not considered the time it takes to make a van, compared with the small quantity treated upon the shovel; and this points to the reason for the failure of all that class of machines called " vanning machines," when used for dressing copper slimes, namely, a lack of capacity. The writer has come to this conclusion through an experience with the Rittinger side percussion-table of the most improved make, sent from Germany to the Calumet and Hecla Mining Company, and with the Ellenbecker tables, used by the same company, both of which are good types of that class of machines. In both of these machines, the tables are suspendetl by rods which allow them to swing, and they can also be adjusted for the purpose of varying the inclination of the table. In the Rittinger machine, the motion of the table is at a right angle to the flow of the slime, being produced by a wiper-cam which throws the table against a spring, which throws it quickly back against a stop, the percussion throwing up the mineral. In the Ellenbecker table, the motion is

Jan 1, 1884

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By E. T. Dumble

PROF. EDWARD ORTON, in his Report on the Occurrence of Petroleum, Natural Gas and Asphalt Rock in Western Kentucky, thus clearly states his ideas of the universal dissemination and rare accumulations of the bitumens:1 " We need to bear in mind that the various members of the bituminous series are abundantly and almost universally distributed among the unaltered sedimentary rocks of the earth's crust. The valuable accumulations of these substances are rare, it is true, but one can scarcely go amiss of petroleum, asphalt or gas, at least in small quantities, among the stratified rocks that retain their original structure." Speaking of the Ohio valley, he adds: "A fifth of one per cent. of petroleum, if distributed through a, thousand feet of rock, would make a total to the acre, or square mile far , beyond any production that has ever been realized from the richest oil field, and percentages of this amount are not only not rare to find, but are even hard to miss." Dr. F. W. Clarke in his Data of Geochemistry (Bulletin No. 491, U. S. Geological Survey, 1911), discussing these views of Orton with similar views of T. Sterry Hunt and Szajnocha, says that they "lead to the conviction that the formation of bitumens is a general process and by no means exceptional. Wherever sediments are laid down, inclosing either animal or vegetable matter, there bitumens may be produced."2 The organic origin of the bitumens, including petroleum, has long been an accepted fact with nearly all geologists, but the method, place, and time of the transformation into petroleum or other bitumen is still under discussion.

Jan 3, 1914