Search Documents

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By Frederick C. Hull

THE grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. USUAL METHODS of EVALUATING GRAIN SIZE A frequently used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.-The Metals Handbook1 has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.-Idealized grain-boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E19-39T. Standard Micrographs.- The Metals Handbook and ASTM Tentative Standard EI9-39T contain micrographs of hypoeutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diam¬eter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying grain size in ASTM Tentative Standard Es-39T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1947

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By H. W. Gillett

BATTELLE Memorial Institute is an endowed in stitution for scientific research in metallurgy, fuels, and allied fields, established by the will of Gordon Battelle, 2nd, as a memorial to his father, Colonel John Gordon Battelle. Before I tell you more of what Battelle Memorial Institute is, I want to go back a bit and tell you why it is. Colonel Battelle began his services in the iron and steel industry in Wheeling in 1866 and in 1883 came to Ohio, where he successively engaged in the iron and steel industry in Cincinnati, Piqua and Columbus. The family had been prominent in Ohio affairs since 1788, when Gordon Battelle's great-great-grandfather came from New England to settle in Marietta. He was one of the pioneers and a member of the famous "Ohio Company."

Jan 1, 1929

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By E. R. Kaiser

ACTIVITY on long-range and on immediate wartime problems shared the attention of specialists in coal research during 1943. Programs of the principal coal laboratories were more adequately financed than in previous years, but all reported shortages of technical personnel. Expansion in coal research in the year to come will depend primarily on the availability of qualified research talent.

Jan 1, 1944

By George S. Rice

GROUND movement and subsidence is an important matter from several points of view and it is regrettable that more papers have not been written on this subject in the past year. Damage may be done to surface buildings or to the higher workings of a mine, and a study of the subject gives valuable in- formation on hanging-wall or roof control. The latter objective is strikingly shown in a recent paper presented by Jack Spaulding on Oct. 21, 1937, before the Institution of Mining and Metallurgy, of Great Britain, entitled "Theory and Practice of Ground Control in the Kolar Gold Field, India." All may not agree with some of his theories that were deduced from studies of the many violent rock bursts at depths of 5000 to 7000 ft., but the data obtained are of great value. His theories of symmetrical ring stresses and symmetrical domes which are pictured as perfect are rather hard to understand as such uniformity is un- likely in view of the irregularities in the formation due to folds and fractures of various kinds. All will agree in principle with this idea of domal effects, which have been observed in many countries, but they are generally irregular.

Jan 1, 1938

By AIME AIME

THREE of the addresses presented at this interesting and important session are printed in full else- where in this issue. The fourth, Mr. Hewett's paper, on "Cycles In Metal Production" has been issued as Technical Publication 183, and an abstract of it was published on page 162 of last month's issue. The general discussion that followed these four important papers is given in full below. S. A. TAYLOR: I would like to ask Mr. Veasey whether the control of oil in pools includes royalties, and, if so, in case of a new pool how are you going to control, or rather how are you going to describe the limits of that pool?

Jan 1, 1929

By L. E. Young

GERMANY'S recent collapse and the occupation by the Allies of the coal fields of the Ruhr, the Saar, Silesia, Poland, and Czechoslovakia have focused attention on the postwar coal problems of Europe. American coal operators are interested deeply in what is happening in Britain, particularly in the discussion of plans to rehabilitate and reorganize the entire British coal mining industry, as such reorganization will probably determine the place Britain will occupy in the European coal markets for the next few decades. The continuing decline of British out-ut per man-shift, particularly during wartime, has resulted in a most serious effort to determine whether this unfortunate trend is due to the physical condition of the coal seams, poor management, poor engineering and planning, inadequate use of power and machinery, or failure of labor to co-operate with management.

Jan 1, 1945

By WILFRED SYKES

IT is with particular pleasure that I welcome the members of the Open-hearth Conference of the I American Institute of Mining and Metallurgical Engineers to this meeting, as I feel this is one of the most useful activities of the Institute in the field of ferrous metallurgy. For the information of our other members I might say the Open-hearth Conference was organized by Mr. Reynders when he was president, and is made up of open-hearth superintendents and metallurgists. All the plants are invited to send representatives, and practically all do, with the exception of the U. S. Steel Corporation. It meets twice a year to discuss various problems in connection with the manufacture of steel, and its minutes are published for the benefit of those attending, the expense being defrayed by the participating companies. This conference, .1 believe, should be a model for activities in the other branches of the work covered by this Institute. It works, not by reading formal papers, which we all know is not a very satisfactory method to bring out the experience of others, but rather by a round-table method of discussion. The spirit of the meetings is such that each member feels perfectly free to state his experience, and he gets as much as he gives. A series of topics for, discussion is brought to the attention of the chairman and after one is exhausted the next point is taken up. In this way there is a real interchange of ideas and experiences which cannot fail l to be of the greatest benefit to those attending. That these meetings are beneficial is evidenced by the "continued growing attendance and lively discussions at these half-yearly meetings.

Jan 1, 1930

By H. J. Wogner

STORAGE of natural gas in underground reservoirs is one of the most important developments in the natural gas industry in recent years. However, it is only when we consider this development together with proved fuel reserves, the know-how of the fuel technologist, and the possibility of making manufactured gas available over large areas, that we begin to appreciate fully the impact that underground storage of gas may have on the future growth and development of large areas in the United States. During the past winter, shortages of natural gas in the industrial East were given wide publicity and domestic consumers were requested to reduce their requirements to a minimum, so that war plants might have sufficient gas to continue operations. Curtailments would have been more drastic except for the fact that large volumes of natural gas had previously been stored in underground reservoirs. Storage of natural gas in depleted or partly depleted gas or oil sands is not new, having originally been tried, as far as I know, about 1915. About five or ten years later an attempt was made to store manufactured gas in a depleted gas sand. This proved unsuccessful at first because the gas was not properly cleaned and the impurities plugged the pores in the sand.

Jan 1, 1945

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938

By Ira B. Joralemon

INDIVIDUALS and small companies have discovered and brought into production the mining districts of the United States. Hardly an exception comes to mind, save for the disseminated copper properties and the great iron mines. In spite of this fine record that has made possible the industrial greatness of the country, mining by small companies and by individuals has become a vanishing phenomenon. In Nevada, the lair of rugged individualism, there are fewer operating mines and fewer miners than at any time since the 1860's. The situation in other states is nearly as desperate.

Jan 8, 1950

By Joseph A. Holmes, Henry Kreisinger

At the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a con~mittee consisti~lg of 11. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr..J. K. Clement, physicist. The problem, essentially one of physical chemistry, is estremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of' the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. in volatile matter and from 40 to 75 per cent. of fixed combtistible. The greater part of the latter is burned on the grate: but the volatile combustible leaves the freshly-charsed coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible mill leave the furnace only partly burnecl, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven oft' per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 30 cu. ft., the burning mixture will stay in it,

Jan 1, 1911

By Kirtley F. Mather

FROM almost every point of view, petroleum was "strategic mineral number one" during the World War that ended in 1945. Even the spectacular advent of the atomic bomb in the final days of the conflict did not displace it from its position of prime importance, although within a few years uranium will almost certainly be the "number one" material in the minds of military strategists, if it is not even now in that position. But both as fuel and as raw material for chemical industries, petroleum will hold the center of the stage for many years to come. Hardly any other substance illustrates so fully the manner in which science and technology may be combined to achieve the utmost success in contributing to human efficiency and comfort. Fundamental to any understanding of the problems implied by my topic

Jan 1, 1948

By Henry C. Freeman

During the early period of the construction of the Illinois and Michigan Canal, about 1838, in excavating for the canal, where the present town of Utica stands, hydraulic limestone was discovered, and its value was recognized. A kiln for calcining and a mill for grinding were erected, and the cement was used in the construction of the locks of the canal. This property was subsequently bought by the present owner, Mr. James Clark, and the work has been continued to the present time in much the same primitive manner as it was begun. The bed is exposed in the Illinois River valley by stripping off a few feet of the covering rock. It is from 4 feet to 6 feet 9 inches thick, and nearly level, dipping gently to the northeast. The Utica Cement Company's establishment, which is two miles west of Utica and two miles east of La Salle, was an outgrowth of the Illinois geological survey. The writer was in charge of the district which included La Salle county, and, in working out the details of the geology of that county, discovered, below the Utica bed, another workable hydraulic limestone, which makes its appearance in the northern bluff of the Illinois River valley, rising above the water level at the point where the company's works are established. This cement group, of which there are several thin beds, lies just below the St. Peter's sandstone, with a few feet intermediate of transition-rock, which appears to represent the Calciferous, and is exhibited in place, in concretionary form, at the top of the bluff. The hydraulic beds are very regular, and the one worked by the company is 10 feet thick; or, speaking more definitely, there are two beds, separated by 18 inches of sandstone, lying about two feet above the bottom, and the two beds are worked as one, the sandstone being first cut out and removed, to prevent mixture. In 1869 I was invited to join with a company, and to take charge

Jan 1, 1885

By F. B. WEEKS

I HAVE chosen for my subject a mining district which in an article published four years ago I referred to in the following words: "One of the un- usual anomalies of mining development and history is that a district having added thirty or more millions of wealth to a principal mining state, situated within four to six miles of two transcontinental railways and two auto highways, and within 150 miles of the most widely advertised part of the United States, should have been so completely lost sight of that probably not one mining man in ten can tell offhand where it is situated." But this district never was a dead one: it was only slumbering. During the past four months, day by day, it has been emerging from that state of slumber.

Jan 1, 1929

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942