Search Documents

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By AIME

NEW YORK'S largest hotel, the Pennsylvania, will be filled with mining and oil men and metallurgists the third week of February when some 3000 AIME members, their wives, and guests will gather for the Institute's 1948 Annual Meeting-its 166th general meeting. Except for the usual Sunday afternoon and evening sessions of the Mineral Industry Education Division at the Columbia University Men's Faculty Club, the big assembly will be under one top and members will not this year have to consult compass and map to find their next session. Possibly enervated by the stupendous effort of the Anniversary Celebration last spring and the plethora of highly successful fall meetings, the various committees have been a trifle slow in arranging their social and technical programs, but in mid December as we go to press there is already much to report indicative of substantial fare and high interest. The definite timetable schedule will appear in the February M&M.

Jan 1, 1948

By A. Patton, F. N. Speller

The use of roll scale in the Bessemer process dates back, to the best of our knowledge, at least 20 years. It was first used by the Ohio Steel Go., Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam McDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to shorten the length of the blow, or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it was dumped into the empty iron ladle by the wheelbarrow-load, and at times was dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerabIe reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions. In using roll scale and other oxides of iron to facilitate and control the refining of pig iron in the converter, the Bessemer plant has borrowed one of the most active agencies used in the open-hearth process with, as would be expected, much the same results. The effect of such additions to the Bessemer charge may be discussed as to the influence of this practice on quality, production and cost.

Jan 1, 1917

By Ivor Jenkins

PROCESSES employing controlled atmospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been associated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and difficult problems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases Controlled atmospheres such as dissociated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties: especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,1 but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1947

By Percy W. Bidwell

THE statisticians had defeated Germany months before she invaded Poland. With batteries of adding machines they had proved that she was suffering from serious deficiencies in critical food- stuffs and in practically all of the raw materials necessary for the conduct of modern warfare. Their calculations showed that with respect to fats, oils, wool, cotton, hides, petroleum, iron, copper and other metals, the Reich was bound to be at a great disadvantage vis-a-vis the French and British as long as the latter could keep open the lines of sea communication. The conclusion seemed obvious-"Germany can't win." The more cautious of the commentators introduced qualifications as to the length of the war and the tightness of the British and French blockade. They also made a third qualification as to the character of the struggle- whether it was to be a war of attrition or a war of movement. But since the invasion of Norway in April, there is no longer any doubt on this score. It is a war of movement-a war in which fuel, lubricants, and metals are being consumed on a scale never before seen.

Jan 1, 1940

William B. Phillips, Birmingham, Ala.: The analysis of Pratt coal made by myself, and given by Mr. Ormsbee in his paper (p. 113), is likely to mislead the reader as to the real nature of this coal. It represents the very purest coal that I have been able to get, and does not represent the average composition of the lump-coal as prepared for market. I wish it were true that the coal had no more than 2.50 ash and 0.83 sulphur. The analysis of McCalley is nearer the real figures than any of the others. There is no use in giving an

Jan 1, 1896

By Lawrence A. Soltis

Senior engineering or executive management positions are filled by engineers who are evaluated on their performance, knowledge, skill, and maturity. Not only is technical expertise required but a knowledge of sales and marketing, finance, law, industrial relations, and public affairs is necessary. The University of Wisconsin-Extension offers an innovative post-baccalaureate degree program blending technical and professional subjects the Professional Development Degree in engineering (PDD)-designed to bring various opportunities for learn-

Jan 4, 1978

By H. C. Lay

No one who knows the conditions of altitude, difficulty of access, shortness of working-season, etc., under which the work of the U. S. Geological Survey in the Rocky Mountains is carried on, can fail to be impressed with the magnitude and accuracy of the results obtained. Yet, in the necessarily brief time given to any one district, maily minor features must remain unregistered. The purpose of this paper is merely to place on record observations, made during nearly eighteen years, of local phenomena in themselves unimportant, which, however, if collated with similar memoranda from neighboring regions, may lead to something of value. The Telluride quadrangle in southwest Colorado is a tract of fifteen geographical minutes on a side, the NW. corner of which is in Long. 108º W., Lat. 38º N. Topographically it is essentially a lofty horseshoe, some of the peaks of which rise more than 14,000 ft. above tide, the interior (with an average altitude of 9000 ft.) being the eastern edge of the rolling Colorado-Utah plateau, and, in its turn, deeply cut by the canons of the San Miguel river and its tributaries. The range-summits are mainly igneous rocks, partly intrusive (such as massive " stocks" and laccolites, left bare by superior erosion), but mostly bedded volcanics of an average vertical thickness of 3500 ft., which change with changing height from andesite to rhyolite. The lowest series of these volcanic rocks, known as the San Juan formation, lies conformably upon the sedimentary San Miguel conglomerate, which dips gently east., and is attributed provisionally to the

Jan 1, 1902

By C. J. Haigh

Stockpiled and currently produced zinc plant residues containing zinc ferrite are to be treated at a rate of 350 tonne per day in a plant that is being constructed at the Risdon works of the Electrolytic Zinc Company of Australasia Limited (E.Z.). Start-up of the plant is scheduled for December, 1970. The residue is to be treated by a hydrometallurgical process that was developed by E.Z. in Australia, by Det Norske Zinkkompani in Norway, and by Compagnie Royale Asturienne des Mines (Asturiana de Zinc) in Spain. The process, as it is to be used at Risdon, is simple, consisting essentially of two stages : 1. A leaching stage at atmospheric pressure in which the zinc ferrite contained in zinc plant residue is dissolved in spent electrolyte, fortified with make up sulphuric acid, at a temperature in the range 70 to 95ºC. Undissolved solids containing lead and precious metals are separated for sale to a lead smelter. 2. An iron precipitation stage at atmospheric pressure in which ferric iron is precipitated from a slightly acidic solution at 90 to 95ºC as ammonium jarosite, a crystalline double sulphate which is relatively coarse, and is easily filtered and washed free of zinc-bearing solution. Calcine is used to neutralise the acid that is liberated during precipitation of the iron. Also included in the Risdon plant are a separate stage for oxidation of ferrous iron by injection of air, and a pre-neutralisation stage, using recycled oxidation stage pulp, to neutralise excess acidity from the leaching stage before the jarosite precipitation stage. The residue treatment plant consists of conventional equipment such as covered agitated vessels, thickeners and filters. Operation will be continuous and product solution will join the main zinc plant circuit for further purifications and electrolysis. Marketable zinc production will be increased by 70 tonne per operating day by the treatment of residue.

Jan 1, 1970

By Robert T. Pring

IN addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company1 estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor. Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the process. METHODS OF DUST CONTROL "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are, in order of their desirability, as follows: I. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom practical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 Of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1940

By Samuel J. Sims

The Grace mine magnetite deposit, located 2 miles north of Morgantown in Berks County, Pennsylvania, was discovered in 1948 by an aerial magnetometer survey. It is situated on the southern border of the Triassic lowlands section of the Piedmont province. Cambrian sandstones, shales, and limestones overlie Precambrian crystalline rock and were folded and thrust-faulted during the late Paleozoic Appalachian revolution. Late Triassic continental sediments were deposited on the deformed basement rocks and were intruded by Late Triassic diabase dikes and sills before regional tilting and normal faulting occurred. The Grace mine magnetite ore is characteristic of the Cornwall type. The ore has replaced a Cambrian limestone lens isolated between Triassic diabase footwall and Triassic sedimentary rock hanging wall. The ore body is roughly tabular in shape, dips 20° to 30°NE and plunges about 20°N80°E. The ore is granular, fine- to medium-grained, typically consisting of unevenly distributed magnetite in a matrix of light green to white serpentine gangue. Magnetite is the major ore mineral, pyrite and chalcopyrite are common accessory minerals, and pyrrhotite occurs locally. Sphalerite, marcasite, galena, hematite, digenite, and goethite are uncommon. Serpentine, talc, and chlorite are the major gangue minerals; calcite and dolomite are common, and phlogopite, tremolite, and biotite are present locally. Apatite is a common accessory; sphene is rare. Calcium-magnesium silicates were formed first by contact metamorphism of impure limestone by the intruding diabase. Later, the silicates were altered hydrothermally to the serpentine- talc-chlorite assemblage now present. Magnetite, the first ore mineral, formed by replacing serpentine and was followed by pyritepyrrhotite and then by chalcopyrite-galenasphalerite. Marcasite, secondary pyrite, goethite, and hematite are secondary minerals resulting from alteration of pyrrhotite and magnetite. It is estimated that confining pressure was about 1500 bars and the temperature range was 500° to 675°C during ore formation.

Jan 1, 1968

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By D. B. McDyre

THE object of this study was to compare variations in slag volumes with tap changes while maintaining all other factors constant. This meant: 1. Same type of heat (Spec. SAE 1030). 2. Same charging material (3500 lb foundry, 4000 lb bought scrap). 3. Same amount of sand by weight to fix slag line. 4. Same method of melting with the exception of tap changes. 5. Same method of weighing slag after each test. The equipment of the Dodge Steel Co. consists of a 132-ton Heroult furnace lined with silica brick, using three 8-in. electrodes and a 2000-kva transformer, with four tap changes. In the melting practice we use a Fischer Carbanalyzer and a Herty viscosimeter and try to standardize all heats by making necessary carbon and slag adjustment before boil to keep all heats as uniform as possible.

Jan 1, 1947

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By W. A. Young

Polynomial functions of temperature were obtained for the specific heats, thermal diffusivities, and thermal conductivities of zirconium hydrides containing 4 at. pct U. Three hydrides (H/Zr atom ratios of 1.58, 1.65, and 1.70) were studied over the range a" to 900°C and a fourth (H/Zr = 1.81) was studied over the range 0° to 760°C. The specific heats were determined from enthalpy measurements which were obtained using a unique drop calorimeter specifically designed for use with materials in which high temperature phase transitions and/or high dissociation pressures occur. Thermal diffusivities were measured by the flash method using a pulsed laser. The thermal conductiuities were obtained as the product of specific heat, thermal diffusivity, and density. The specific heats agree, within 10 pct, with values derived using a theoretical model in which the hydrogen and zirconium atoms are treated as Einstein and Debye oscillators, respectively. RELIABLE values of the thermophysical properties of the fuel are required to predict the operating temperatures and temperature response of SNAP nuclear reactors. Among the most important of these properties are the thermal conductivity, specific heat, and thermal diffusivity. A considerable number of investigations1-4 have been made of these properties for the Zr-H and Zr-H-U systems.* However, little of the drides, however, this direct method cannot yield meaningful results, since the hydrogen will redistribute under the influence of the thermal gradient, thus forming a concentration gradient; hence, one has a spectrum of compositions, rather than a homogenous alloy. Although the "average" composition of the material may be identical to the initial uniform concentration, the directly measured value of conductivity will be dependent on the thickness of the specimen, due to the highly sensitive dependence of transport properties on hydrogen content. This dependence is strikingly illustrated by the work of Bickel,5 who found that the electrical conduction of zirconium hydrides ranges from primarily hole conduction to primarily electronic conduction, depending upon the hydrogen content. Fortunately, the direct measurement of thermal conductivity is unnecessary, since it can be expressed as the product of the specific heat, thermal diffusivity, and density, all of which can be directly measured with considerable accuracy. EXPERIMENTAL Specimen Preparation. The combined fuel-moderator material used in SNAP reactors is a hydrided zirconium-uranium alloy containing -10 wt pct U. The alloy used in this work was representative of that used in nuclear reactors except that normal uranium was substituted for the enriched uranium required for reactor usage. It was produced by a triple-arc-melt and double-extrusion process. All specimens were prepared from a single cylindrical extrusion which contained 10.30 pet U, 89,35 pct Zr, and 0.35 pct impurities, The specimens for each composition were hydrided simultaneously with ultrapure hydrogen (10 ppm total impurities) using standard fuel production techniques which routinely yield homogeneous, crack-free fuel with negligible increases in the impurity levels. The hydrogen content of each specimen was determined from its weight gain and the density was measured by liquid displacement, Chemical analyses yielded hydrogen concentrations which agreed with the weight gain data within ±0.02 in H/Zr atom ratio) the concentrations of all other elements agreed almost exactly with the initial values after adjustment for the added hydrogen. The specimens used for the determination of specific heat were centerless ground to 2.00 cm diam after hydriding. A thin slice was carefully removed From each end for metallographic examination. In every case, this examination revealed a uniform structure as evidenced by the appearance and distribution of the two phases present in the fuel at the hydrogen concentrations used. TWO specimens (H/Zr = 1.600 and 1.632) appeared to be entirely 6 phase with equi-axed grains; the specimen with H/Zr = 1.756 showed

Jan 1, 1970

By W. A. Thatcher

Nearly three years of experience in Spanish Honduras has placed the writer in possession of many facts concerning its resources which may be of interest to the Institute. According to the most trustworthy surveys, Honduras is bounded on the north and east by the Caribbean Sea; southeasterly by the river Segovia (or Wanks), which flows into the Caribbean at a point called Cabo Gracias a Dios (Cape Thanks be to God), long famous as the favorite hiding-place of the celebrated pirate, Morgan ; southwardly by a corner of San Salvador, the Bay of Fonseca, and the Republic of Nicaragua; Guatemala and San Salvador form tile western boundary. It is one of the five republics composing Central America, has a population of about 310,000 and an area of 150,000 square miles, lying between the 13th and 16th degrees of N. latitude, extending from north to south 200 miles, between the Atlantic and Pacific, and 400 miles from east to west, between Guatemala and Cape Gracias a Dios. It is composed of 13 States or Departments, under one common law. The principal resources are valuable woods, hides, rubber, tobacco, coffee, fruit, cattle, silver and gold. It is of the mineral resources of the country that I will speak, calling attention to the most noted mines, and their relative position to Tegucigalpa, the capital. The introduction of foreign capital into the country dates back about eleven years, and to-day there are at least twenty-five well organized companies.

Jan 1, 1892

By N. A. Gokcen, J. Chipman

Aluminum and oxygen dissolved in liquid iron were brought into equilibrium with pure alumina crucibles and atmospheres of known H2O and H2 contents to study the reactions: 1—Al2O3(s) = 2 Al + 3 0; 2—Al2o3(s) + 3H2(g) = 2Al+ 3H2o(g); and 3—H2(9) +O = H2O(g). Aluminum strongly reduces the activity coefficient of oxygen and similarly oxygen reduces that of aluminum. Values of the product [% All" • [% O]3 are much smaller than those found in previous experimental studies and are of the order of magnitude of the calculated values. ALUMINUM is the strongest deoxidizer commonly A used in steelmaking, but the extent to which it removes dissolved oxygen has been debatable. The relationship between aluminum and oxygen has not been determined reliably not only on account of the usual experimental difficulties at high temperatures but also because of uncertainties in the analyses of very small concentrations of oxygen and aluminum. The earliest experimental attempt of Herty and coworkers' was followed by a more systematic study of Wentrup and Hieber.' These authors added aluminum to liquid iron of high oxygen content in an induction furnace and considered that 10 min was sufficient to remove the deoxidation products from the melt. Parts of the melts thus obtained were poured into a copper mold and analyzed for total aluminum and oxygen (soluble plus insoluble forms), assuming that the insoluble parts were in solution at the temperatures from which samples were taken. It is conceivable that the furnace atmosphere in their experiments, consisting of mainly air at 20 mm Hg pressure, was a serious source of continuous oxidation and therefore that their oxygen concentrations were correspondingly high. Scattering of their data was explained to be well within the maximum inaccuracy of 10°C in the temperature measurements and errors of ±0.002 pct each in the oxygen and total aluminum analyses. Maximum and minimum deoxidation values, i.e., values of the product [% All' . [% O] differed by factors of 10 to 15; mean values of 9x10-11 and 7.5x10-9 ere reported at 1600" and 1700°C, respectively. Hilty and Craftsv determined the solubility of oxygen in liquid iron containing aluminum, using a rotating induction furnace. Pure alumina crucibles used in their experiments contained the liquid iron which in turn acted as a container for slags of varying compositions consisting mainly of Al2O3, Fe2O3, and FeO. The furnace was continuously flushed with argon, and additions of aluminum and Fe2O3 were made in the course of each experimental heat. The inner surfaces of their alumina crucibles were covered with a substance other than pure Al2O3, containing both iron oxide and alumina. Although frequent slag additions can change the composition of slag in the liquid iron cup formed by rotation, the inner surface of the crucible must depend upon the transfer of oxygen or aluminum through the liquid iron for any adjustment in composition. It is not clear that their metal was in equilibrium with the crucible wall, but it is clear that it was not in equilibrium with Al2O3. Their deoxidation product, [% A].]" • [% O]3, varied by a factor of more than 50; the average values of 2.8x10- and 1.0x10-7 were selected for temperatures of 1600" and 1700°C, respectively. Aside from the experimental determinations, attempts have been made to calculate the deoxidation constant for aluminum indirectly from thermody-namic data. Schenck4 combined the thermodynamic data for Al2O3 and dissolved oxygen in liquid iron by assuming an ideal solution. His calculated values are 2.0x10-15 and 3.2x10-13 at 1600" and 1700°C, respectively. Later, Chipman5 attempted to correct for the deviation from ideality and derived an expression which led to deoxidation values of 2.0x10-14 and 1.1x10-12 at 1600" and 1700°C, respectively. The errors in these treatments originate mainly from inaccuracies of thermal data and uncertainties regarding the activity coefficients of dissolved oxygen and aluminum. The purpose of this investigation was to study the equilibria represented in the following reactions in the presence of pure alumina: Al2O3(s) = 2Al + 3O K = aAl2.ao3 [1] Al2O3(s) + 3H2(g) = 2Al + 3H2O(g) H2O K2 = aAl2(H2O/H2 ) [2] H2(g) +O = H2O(g) K3 = 1/ao (H2) [3] The experimental method consisted of melting pure electrolytic iron, usually with an initial charge of aluminum, in pure dense alumina crucibles under a controlled atmosphere of H,O and H2 and holding

Jan 1, 1954