Search Documents

By G. W. Healy, W. D. Forgeng, N. R. Griffing

The liquidus surface of the C-Cr-Fe system to 1900°C has been mapped from carbon solubility and freezing point measurements, metallographic observations, and published data. In the graphite field, the surface drops precipitously to meet a slope descending from the Cr3C2-C join through the mixed carbide fields to a meandering eutectic valley; this flows from the Cr-C to the Fe-C edge. On the low-cavbon side of the valley, the surface rises to the chromium corner. 1 HE purpose of this inquiry was to gain a more complete knowledge of the C-Cr-Fe liquidus surface. This required an extensive study of carbon and chromium-rich alloys which, in the past, have received the least attention. Sanbongi el al.1 measured the solubility of carbon in liquid alloys containing up to 25 wt pct Cr at temperatures of 1460" and 1545°C and found that it increased with chromium content and temperature. Lucas and wentrup2 also made solubility experiments in graphite crucibles, but at higher chromium contents in the range of 38 to 80 pct and at temperatures of 1550" to 1700°C; however, their experiments were relatively few, and the effect of temperature was not consistent. The present investigation included compsitions ranging from 0 to 94 pct Cr and 1.4 to 11.7 pct C at temperatures up to 1800°C. Saturation experiments in graphite crucibles, thermal analyses during freezing, and metallographic and X-ray diffraction studies were employed to obtain desired information which, together with published data from other investigations about the binary edges and the ternary system at lower carbon levels, made possible the construction of a comprehensive C-Cr-Fe liquidus surface. C-CR-FE LIQUIDUS SURFACE The derived ternary liquidus surface is shown in Fig. 1 where the solid curves are liquidus isotherms. The dashed curves and the binary edges are the liquidus field boundaries of the primary crystals, the arrows along these boundaries indicating their direction with decreasing temperature. Each intersection of three internal boundaries is the composition of liquid involved in four-phase isothermal equilibrium with the three primary crystals whose liquidus fields touch there. It may be observed that a total of six four-phase equilibria occur at melt temperatures. The general topography of the liquidus surface consists of a eutectic valley sloping down from the Cr-C edge at 3.2 pct C to the Fe-C edge at 4.25 pct C. The liquidus surface rises in two directions from the valley, one hillside terminating at the Cr-Fe edge while the opposing hillside rises toward the carbon corner out beyond the top edge of Fig. 1. Both hillsides are interrupted by intersections of surfaces or joints representing the liquid colmpositions of various three-phase equilibria. Seven primary crystals occur, namely a(bcc), ?(fcc), graphite, (Fe, Cr)3C capable of dissolving as much as 15 pct Cr, and three different chromium carbides in which iron is partially soluble by substitution for chromium. The composition ranges of the primary l~hases at melt temperatures are shown

Jan 1, 1962

By W. T. Bishop, G. A. Crowe

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By G. A. Crowe, W. T. Bishop

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

It is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4.5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik's tests will be discussed later Such torsion does not readily yield actual stress and strain values. Therefore a pre- liminary study was made of the effects of repeated direct stresses, that is, tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluniinum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension rest This alloy permitted, therefore rather accurate cont.rol at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this invest~gation appear sufliciently interesting to extend the method of attack in various directions It is intended to study (11 the effects of cycles up to a tew thousands and (2) the effects of strains of different magnitude in tension and compression respectively 'The latter variable also includes a. a special case the effects of compressive strains.

Jan 1, 1949

By F. Louis Grammer

THE difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace gas is richer in CO, and poorer in hydrocarbons and hydrogen, as is shown in Table I. TABLE I.-Volume-Composition of Producer-Gas and Blast-Furnace Gas.. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO . 22 to 33 25.5 00., . 6 to 3 13.0 H . . 13 to 7 1.5 CH, 3 to 1.5 0.0 N . 54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydro-carbons and, hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur-namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the products which are specially high in sulphur-content. An advantage would be gained if coal was coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Sep 1, 1908

A USEFUL and very ingenious idea was surely that of the inventor of AN a short way of extracting gold and silver from the sweepings of all those arts that handle them as well as every particle that smelters of ores might have left in the slags, and also that in some ores themselves. This is done without using great labor in smelting but by the sole means and virtue of mercury. To do this, first make a large bricked pan of stone or wood and arrange a millstone inside which rotates in the hollow of this pan like that of a flour mill. In the hollow of the pan put some of your material containing gold after it has been crushed well in a mortar and then washed and dried. Grind it in the said mill, moistening it meanwhile with vinegar or water in which sublimate, verdigris, and common salt have been dissolved. Then enough mercury to cover these materials is poured over them. They are agitated inside for an hour or two, by turning the mill either by hand or with a horse, depending on the device that you have arranged. Remember that the more the mercury and the material are rubbed together in the mill the more it can be believed that the mercury absorbs the substance that the materials contain. Finally, thus prepared, the mercury is separated from the earthiness with a sieve or by washing and thus the mercury is retrieved. Then, make it rise with a little cucurbit or pass it through a purse and there will remain at the bottom the gold, silver,. copper, or whatever metal you placed in the pan under the millstone to be ground. Wishing to know this secret, I gave to the one who taught it to me a ring with a diamond worth twenty-five ducats, and I also pledged myself to give him the eighth part of whatever profit I should gain from this

Jan 1, 1942

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By Walter F. Pond, Kendall E. Born

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By Kendall E. Born, Walter F. Pond

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as com- pared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams. Coal at Wales, in Sanpete county, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it "rock that would burn." In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the old Spanish Trail from Santa Fe. New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.

Jan 1, 1925

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

By T. Y. Yan

SUMMARY Laboratory high pressure column tests have shown that the presence of 1-20 ppm of aluminum ion effectively prevents permeability loss during uranium leaching with leachates containing sodium carbonate. If added after permeability loss has occurred, aluminum ion can restore the permeability to nearly its original value. No deleterious effect was observed on uranium leaching performance and the technique should be quite compatible with all field operations. INTRODUCTION The recovery of uranium values from underground deposits by in situ leaching or solution mining has become economically viable and competitive with conventional open pit or underground mining/milling systems (Merrit, 1971). In situ leaching processes are particularly suitable for small, low-grade deposits located in deep formations and dispersed in many thin layers. Many such ore bodies occur along a broad band of the Gulf Coastal Plain (Eargle et. al., 1971). The advantages of the in situ leaching processes have been reviewed (Anderson and Ritchi, 1968). In the in situ leaching process, a lixiviant containing the leaching chemicals is injected into the subterranean deposit and solubilizes uranium as it traverses the ore body. The pregnant lixiviant or leachate is produced from the production well and is then treated to recover the uranium. The resulting barren solution is made up with the leaching chemical to form lixiviant for re-injection. Upon completion of the leaching operation, the formation is contaminated with leaching chemicals and other species made soluble in the leaching operation and has to be treated to reduce the concentration of these contaminants in the ground water to levels acceptable to the regulatory agencies (Witlington and Taylor, 1978). Restoration is accomplished by injecting a restoration fluid, which could be the fresh water or water containing chemicals, into the formation. As it traverses the leached formation, the restoration fluid picks up the contaminants and is then produced at the production well. This produced water is either disposed or purified for recycle. In both phases of operation, formation permeability or well injectivity is one of the most important parameters which determines the viability of the in situ leaching process. Low formation permeability limits production rates, leading to uneconomical operations. The formation is said to be sensitive if there is a sharp loss of permeability on contact with water and other fluids. Many uranium bearing formations, for example, the Catahoula formation of the Texas Coastal Plain, contain significant amounts of clay minerals which are water sensitive. Serious permeability losses can occur when the pH and chemical composition of the lixiviant is significantly different from that of the formation water. Jones has investigated the influence of chemical composition of water on clay blocking of permeability (Jones, 1964) and Mungan studied permeability reduction through changes in pH and salinity of the water (Mungan, 1965). Various mechanisms of permeability damage have been proposed and reviewed (Jones, 1964; Mungan, 1965; Gray and Rex, 1966; and Veley, 1969). When large amounts of swelling clays are present, a significant fraction of the flow channels in the formation can be reduced due to swelling. However, in most cases, swelling need not be the main cause of permeability losses. Particle dispersion and migration or clay sliming can be more important causes for formation damage. Clay particles entrained in the moving fluids are carried downstream until they lodge in pore constrictions. As a result, microscopic filter cakes are formed by these obstructions, plugging the pores, effectively restricting fluid flow and reducing the formation permeability. Moore found that as little as 1-4 percent clays present in a fine grained sandstone could completely plug the formation if they are contacted by incompatible injected fluids (Moore, 1960). It has been found that injection of NaHC03/Na2CO3 lixiviant into formations with significant clay content often leads to loss of formation permeability and well injectivity. To alleviate this problem a change of the lixiviant composition to KHC03/K2CO3 has been proposed. At present, however, many in situ leaching operations employ NH4HC03/(NH4)2C03 mixtures as a source of carbonates. This approach has been successfully used in South Texas by Mobil, Intercontinental Energy, Wyoming Minerals and U.S. Steel, etc. The use of ammonium carbonates solutions, however, contaminates the formation and requires a time-consuming restoration operation. The other approach to reduce the permeability loss is to pretreat the sensitive formation with chemicals which prevent clay dispersion and migration. Such chemicals include hydroxy-aluminum (Reed, 1972 and Coppel et. al., 1973), hydrolyzable zirconium salts (Peters and Stout, 1977), hydrolyzable metal ions in general (Veley, 1969) and polyelectrolyte polymers (Anonymous). Still another approach, is to minimize the "shock" caused by sudden injection by gradually changing the chemical composition of the injected fluids from that of the formation water. THE APPROACH Since permeability loss can be an important factor limiting the efficiency and economic viability of the in situ leaching process, a study was initiated on

Jan 1, 1982

By R. C. Ernrnons, Ray Wilcox

RECENTLY completed experimental work, carried out in the department of geology at the University of Wisconsin, aiming at a prevention of silicosis in industry has been reported in the American Mineralogist. A vast amount of work on silicosis has been reported in the literature, the clinical aspects having been especially well covered. A host of critical observations have been made on the variations in the nature of the silicosis problem in different environments, and a great deal of valuable experimental work has helped to clarify these observations. At present a greater amount of information of a critical sort is available than ever before, which affords a more sound basis for interpretive thought. It has been observed in industry that essentially pure silica dust gives rise to silicosis. Jones would modify this conclusion to place the responsibility on sericite, a silicate mineral present in the siliceous dust. Material such as granite dust, which carries a high free silica (quartz) content, is also a silicosis hazard. But sericite, too, is usually present in granite. In general it is widely believed that silicosis is caused by the presence in the lung of silicic acid regardless of the source. This view is adopted here.

Jan 1, 1937

Jan 1, 1933

On the map of Europe the shield-shaped area included in the boundaries of Rumania appears too small to constitute a very important factor in the wold's oil production. The country has a total area of 122,000 square miles of territory, about one-fifth of 1 per cent. of the world's surface, from which about 21/2 per cent. of the world's oil was produced in 1929. This relatively small area also constitutes one of the known billion-barrel reserves of the world. Oil has been found in various localities in the foothills of the Carpathian Mountains, extending more than 100 miles in length at their base. It is rather unusual that, while the extent of prospective territory seems to be large, the area of the commercially productive pools is comparatively small. Oil accumulation in Rumania is closely associated with salt stocks. Shows of oil are encountered from the Pliocene down to the Cretaceous. Most of the production, however, comes from the Pliocene, the chief producing sands of which are the Dacic and the Meotic, although some oil is produced from the Levantic and the Pontic. The Meotic as a source of oil was known for many years, but the intensive output from this sand series is a comparatively recent development and accounts in a big measure for the steady increase in Rumanian production. In the early part of the summer of 1929 the Astra-Romano (Royal Dutch) completed a well at Moreni in what is thought by some to be a fourth Meotic sand (a new sand series) at a depth of 5200 ft. with an initial production of 2000 bbl. a day of 41" gravity oil. The development of this new horizon has been somewhat retarded by the disastrous fire which occurred at Romano-Americana's well No. 160 in Moreni, but its discovery adds materially to the future life of the Moreni area, one of the country's oldest fields. Rumania's production for 1929 is estimated at 35,556,000 bbl., a daily average of 97,400 bbl. This compares with the total of 31,542,000 bbl. for the previous year, a daily average of 86,180 bbl., or an increase of 12.73 per cent. Rumania now occupies seventh position in the world's oil picture, it having been replaced as the sixth in importance by the Dutch East Indies in 1929. Table 1 shows a comparison of production by districts and fields.

Jan 1, 1930

By W. B. Heroy

ONLY through the mineral fuels can large amounts of energy be transported to great dlstances and stored for long periods for future use. Coal has the advantages over oil of greater safety of handling and smaller losses in storage. But oil is, in the present stage of technical advancement, the more economical source of liquid fuel for internal-combustion motors. No method for direct use of coal in such motors has been developed that can compete with petroleum products. The automoblle engine and the airplane motor are designed to make the most effective use of gasoline.

Jan 1, 1944

Data about production are practically non-existent before 1860. The Census of 1840 reported a small amount, and a number of small mines were opened in the forties, all of the coal being used locally, or hauled to consumers in wagons. Tonnages shown in Table 72 are estimated from those for which authority is given. Railroads reported coal tonnages carried in the state in 1878 and subsequent years for years ending June 30th;, it is not stated that the tonnage originated in the state. Considering this fact, and the considerable amounts used locally, the tonnages given in Table 72 are certainly not larger than the actual amounts produced.

Jan 1, 1942

By James H. TaVoularis, William J. Wiehagen

This paper discusses the application of commercially available microcomputers for assisting trainers in the delivery and evaluation of new hire, refresher, and occupational training. A brief overview of mine training highlights major issues facing the mine training community. The use of computer-based training has a potential for reducing costs and improving the transfer of conventional training to the job.

Jan 1, 1983