Search Documents

By Ralph E. Esarey, George V. Cohee

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By George V. Cohee, Ralph E. Esarey

In Indiana, 349 wells were drilled for oil and gas in the year 1942. Of this number, 125 oil wells and 21 gas wells were successfully completed and 203 were dry holes. Drilling activity declined 37 per cent as compared with that of the year 1941. This reduction was brought about largely by Federal Conservation Order M-68, restricting drilling to one well on 40 acres, in order to save steel. This Order was later supplemented to permit closer spacing of wells drilled to sandstone formations in southwestern Indiana. Most of the drilling in 1942 was in the southwestern part of the state. Posey County ranked first, with 94 completions and 44 producers; Gibson County, second, with 77 completions and 38 producing oil wells and 2 gas wells. There were 58 drilling operations in the state at the end of the year. During 1942 a total of 589,734 ft. of hole was drilled, of which 231,702 ft. was wildcat footage. The total initial production of the oil wells completed was 9974 bbl. and of the gas wells, 11,148,000 cu. ft. (Table 2). Of the 349 wells completed, 122 were wildcat wells (Table 3); 26 were completed as oil wells; 17 were extensions to proven fields and 9 discovered new pools. Posey County was foremost in wildcat drilling, with 37 wells completed (Table 6). Thirty-five per cent of the wells drilled in 1942 were wildcat, as compared with 25.5 per cent in 1941. It is anticipated that the percentage of wildcat wells drilled in 1943 will be greater, although the total number ol ,wells drilled in the state will probably be less. The new discoveries in Indiana in I942 were, for the most part, one-well pools in the southwestern part—in Posey, Gibson and Spencer Counties (Table 4). Most of the development in pools took place in the . Hazelton and Kirksville pools in Gibson County, Mr. Vernon pool in Posey County and the Vernon Heights pool in Vander-burgh County. Deeper production was obtained from the Osage limestone in the Hazelton pool at a depth of 2402 ft., 650 ft. below the productive McClosky limestone. The well had an initial production of 140 barrels. Extensions to 17 pools in the southwestern part of the state were successfully completed (Table 5). An interesting development during 1942 was new production from the Devonian limestone in the Dodds Bridge pool, Sullivan County. The Ohio Oil Co. deepened one of its wells, which had been producing from a shallow sand, to the,Devonian, and it was completed for an initial production of 77 bbl. Five other Devonian producing wells were completed in that area. Crude-oil production in Indiana in 1942 was 6,609,000 bbl. (Table I). The Griffin field, Gibson and Posey Counties, which produced approximately 3,550,000 bbl., accounted for more than half of the state's production. The Mt, Vernon and New Harmony fields were next in importance of production, with 684,000 and 523,000 bbl., respectively. The price of crude oil was $1.22 a barrel for the old

Jan 1, 1943

By Charles V. Seastone

The hydro-electric plant of the Peninsular Power Co. is located at what is commonly known as Lower Twin Falls on the Menominee River. This location is about 3I/2 miles north of the city of Iron Mountain, Mich. The principal points of delivery of electric energy from this plant are in the mining regions adjacent to Florence, Wis., and Iron River, Mich., and in the cities of Iron River and Iron Mountain. The hydro-electric plant at Twin Falls and the substation of the Iron Mountain Electric Light & Power Co, are connected by a 6,600-volt transmission line carried on steel towers and steel poles, the latter being used within the city limits. The plant at Twin Falls and the substation at Iron River, about 36 miles distant, are connected by a 66,000-volt, duplicate, three-phase transmission line, supported on steel towers. At Iron River, are located a 1,500-kw. auxiliary steam plant, and the substation, from which the current is distributed to the mines in this vicinity. A description of the auxiliary plant, main and customers' substations, and of the main and secondary transmission lines, follows later in this paper. General Layout The relative location of the dam, forebay, and power house will be understood by referring to Fig. 1. The dam is constructed on a ledge of solid rock which forms Lower Twin Falls. This rock ledge offers an excellent location in that the height of the dam, and therefore the amount of concrete, are thereby reduced, and also in that practically no pumping was required in unwatering the dam site. The maximum head provided by the dam is 44 ft., with an average working head of from 40 to 42 ft. The other structures, including the substructure of the power house,

Jan 1, 1915

In an earlier day, a moderate-sized 600 tpd mine could easily require 60 working faces and might use five supervisors. The miner had a tonnage rate as an incentive and was largely his own boss. With the advent of conventional mining machine crews, the typical pattern of resource used changed radically. The number of work places could be cut by a factor of ten, but supervision only by a factor of somewhere around three, or at most, five. Obviously, supervision was increased. Capital use rose at the same time by a factor of approximately eight. Materials used, such as powder and bits, probably in- creased in both quality and unit cost, too. It certainly required a better-trained man to run the machines, but fewer miners were needed. It is clear that each input factor such as land, labor, capital and management, has changed significantly and it would be foolish to attribute all the gain to improved machines. However, concentration of work was a vital consideration in the change, sketched above, and such focusing of work in fewer areas could not have occurred without high capacity mining machines.

Jan 11, 1968

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss's original conclusion' that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

By Lester Uren

The fluid level maintained in wells pumped for oil is an important factor in deter-mining their productivity but one that has received little attention in the literature relating to petroleum-production technology. In the present paper the writer undertakes to show how and to what extent fluid level influences productivity and suggests the use of a fluid level indicator as an aid to the oil producer in maintaining the fluid surface within the well at the proper position. IT is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended, should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the .ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size, of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well.. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 2, 1925

By D. R. Babich, R. A. Allwes, L. V. Wade

The design of a longwall entry system is discussed in this Bureau of Mines paper. This is done primarily through the results of an in-mine case study made of two sets of longwall entries utilizing the stiff- yield pillar design concept. The rock mechanics instrumentation plan used in this case study is shown, including a description of the instrumentation layout and the types of instruments used. The analysis of the stress changes in the abutment and yield pillars is presented in detail as the longwall panels were mined. Conclusions concerning when the pillar first started to experience significant stress, pillar stress history as the longwall face approached and moved past the pillars, stress distribution within the pillars and relative stress changes between yield and abutment pillars are discussed. The paper concludes with a discussion of the redistribution of stress in the vicinity of the long- wall panel.

Jan 1, 1982

By R. E. Rettger

The area referred to in this paper is the southern part of the Permian Basin lying in southwest Texas and southeast New Mexico (Fig. I). Those fields lying along the northern rim of the basin; namely, the Panhandle fields, are not included. The fields within this area are

Jan 1, 1930

By William R. Rumbold

The Kinta valley, in the State of Perak, one of the largest of the Federated Malay States, is probably at the present time the richest alluvial tin-district in the world, Perak producing from 20,000 to 25,000 tons of tin annually, and the Kinta valley being the chief producer. The valley runs approximately north and south, and is 30 miles long by 12 wide. It is very flat, the mountain-ranges on either side rising abruptly from the plain, that on the east being the great Central range of the peninsula, and that on the west a subsidiary range marked " Kledang " on the map, Fig. 1. The valley is drained by the Kinta river, which rises in the eastern mountain range and flows south to join the Perak river, being joined by numerous streams from both mountain-ranges.

Jan 1, 1907

By T. Egleston

The direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German b1oomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Notwithstanding the improvements which have been made in the constrnction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The name of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of' German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process.

Jan 1, 1880

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By J. A. Bownocker

The existence of petroleum in the rocks of Ohio and Indiana seems to have been first shown by wells dug for salt. The fuel, however, was objectionable owing to its odor and inflammability. Not until the Drake well was drilled in 1859 did the people appreciate the value of rock oil, and then they at once began plans to secure the coveted fuel. The first successful well in these two states was near Macksburg, in southeast Ohio, where at a depth of 59 ft. (17 m.) oil was found in commercial quantity (1860). A year later this fuel was secured on Cow Run, in the same county, and at about the same time in Noble, Morgan and perhaps other counties in that part of Ohio. The second great step in the production of oil in Ohio and Indiana was taken in 1884 when the reservoir of natural gas in the Trenton limestone of northwest Ohio was tapped, and where a year later oil was secured in the same formation. Petroleum in this limestone was obtained in Indiana in 1889.&apos; The third step in the production of oil in Ohio and Indiana is associated with the Clinton sand of Ohio. Natural gas in large volume was discovered in that rock at Lancaster, in 1887, and the area has been extended until it has become the largest individual producer in the world. The presence of natural gas in such great volume all but demonstrated to the driller that oil lay hidden near by. Soon the search for it was started but not until 1899 was petroleum in commercial quantity found in the Clinton sand, and a large pool was not located in it until 1907. The fourth step in the developrllrnt of the industry was taken in 1913, when the pool in Sullivan County, in western Indiana, was opened. The producing rock is the Huron sandstone, which is the topmost member of the Mississippian system.²

Jan 1, 1921

By Stuart M. Buck

The term "splint" seems to have been adopted to describe the fracture of the hard bituminous coals of West Virginia. It is not a scientific name, but rather a trade term, and does not indicate a correspondence with English splint. At present it is a popular word, and is very loosely applied to coals of various qualities, in the desire & improve their sale. The Kanawha splint is distinguished by its hardness, dull lustre, coarse fibrous structure, its purity, and especially its resistance to atmospheric influence. It kindles very readily, burns with a bright flame, but does not cake, so that a lump when half consumed, may be broken by a slight blow in its plane of cleavage, though it will resist a strong blow in any other direction. I have seen pieces that have been exposed to frost and sun

Jan 1, 1882

By Fun-Den Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stabi1ity.l-3 Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe.3 Rock blocks formed by sets of parallel joints have been analyzed by Wittke.1,2 The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry. A plane of weakness is represented by its dip and strike in vector form and is reduced to the form of a linear equation. The geometry of the rock block is defined by solving the linear equations. The geometric characteristics of a rock block are based on triangles and tetrahedrons. By this treatment, the three-dimensional geometry is simplified and the number of calculations of forces and moments is reduced. Methods of finding the geometric characteristics are presented, along with equations for calculating the resultant forces and moments and the factor of safety. BASIC ASSUMPTIONS The following assumptions are used : The solid part of the rock mass is much stronger than the rock mass at the plane of weakness and the rock mass will only fail along planes of weakness.

Jan 1, 1972

By W. K. Whiteford

Until the beginning of the year 1930, conditions in the oil industry were such that the production engineer was chiefly concerned with improving the efficiency of development and production technique. Good engineering practice had been adopted to devise and improve methods and materials better suited to drilling for and producing oil and gas. These efforts reduced the hazard and expense of deeper drilling, increased the ultimate recovery from reservoirs and lowered production costs. Equipment was of better design and materials were better suited for the work and were more permanent. These improvements naturally have contributed their share toward increasing the volume of crude oil produced each year. The industry is now faced with a need for preventing a waste of this natural resource; waste which came as a result of continued reckless drilling of new reservoirs. To make a careful study of this economic problem and to devise methods for correcting these conditions was a logical problem for the production engineer. Much time and study have been devoted to the question, and remedial plans have been suggested during the last year and a half. The principles of unit operation have attracted the engineer&apos;s attention, as they present ideal conditions for the most scientific and economical development of an oil field. Unitization During 1930 unitization of producing and potentially producing areas has made real progress, and as each new unitized development is agreed upon the objections that loomed so large at the inception of the idea fade into comparative insignificance. Undoubtedly the outstanding example of the efficacy of unitization is the Kettleman Hills project in California. Unitizing this structure, with its almost incredible reserve, is an important step forward in the industry&apos;s concerted effort toward conservation. With this partial acceptance of the principles of unit

Jan 1, 1931

By H. M. Rutherford

The reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the surrounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently&apos;(7) † regarding either the method or the results. The discovery of several oil fields is now attributed to the use of the reflection method. Reflection methods have been used by the Germans to find the thickness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refraction and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1934

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

The banquet Wednesday evening was attended by about 700. The list of speakers was unusually brilliant and each one proved to be so interesting that it was nearly midnight before the dancing began. Capt. Robert W. Hunt was toastmaster. Captain Hunt is about to celebrate his eighty-first birthday but is blest with unusual vigor and it was a great pleasure to all his friends to honor him at this time. His selection is toastmaster was a happy one. The guest of the evening, if among so many stars one could be selected from the rest, was Charles M. Schwab, who said nothing but the urgent telegram from his dear old friend, Captain Hunt, could have drawn him away from his seclusion on his Pennsylvania farm to attend the meeting in Chicago. Mr. Schwab&apos;s address was, as usual, scintillating with wit and humor; and while lie did not directly or indirectly allude to the steel strike lie did at the end of his talk discuss serious things and gave it as his opinion that any effort to legislate or control the high cost of living would be futile until this country got down to a basis of an honest day&apos;s work for an honest day&apos;s wage.

Jan 11, 1919

By Parke A. Dickey

POTENTIAL differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified to measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles.

Jan 1, 1944