Search Documents

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By C. M. EYE

IN the spring of 1905 I was employed by Messrs. Bradley and Requa, under our fellow member, Thomas Cox, on the mill plans for the Nevada Consolidated, when an opportunity came to go to the Philippines to erect a small mill on the property of the Benguet Consolidated. This I accepted, expecting to be away eight months or so, but it was seven years before I got back. .I sailed in May, on the Coptic, having as room-mate as far as Kobe, A. E. Drucker, who was going out to Korea for the Oriental Consolidated. It was the first trans-ocean trip for either of us, and we had some rather unusual experiences. This was toward the close of the Russo-Japanese war and the Russian fleet was known to be on the way from Suez to Asiatic waters, but it was a matter of doubt whether they would risk a passage between Japan and the mainland, or take the longer but obviously safer route outside of Japan. The Coptic carried much contraband of war for Japan, so naturally did not care to meet this fleet. No definite word being available at Honolulu, we went to the Midway Islands, but the cable station there had very little information to offer, so we proceeded cautiously toward Japan. On the last afternoon out, we steamed due north at half speed for several hours, and finally sneaked into Yokohama at night, to learn that ' the Russian fleet had met the Japanese the day before and had been annihilated. We sailed over the spot in the Sea of Japan a week later, and when we got to Manila we found three of the Russian boats interned and being guarded by the monitor Monadnock and a cruiser. This was only a matter of form, as the Russians were only too glad to be there for the rest of the war, and the boats could not have gone far anyway, for they were literally shot to pieces. The Admiral's flagship had a hole within 3 ft. of the water line, for ward, through which a man could enter by stooping.

Jan 1, 1929

By F. E. Bedale

STUDY of several severe mine explosions that occurred during the winter of 1907 led to the belief that coal dust was a definite explosion hazard. The Consolidation Coal Co. was a pioneer in the early work to' eliminate this hazard and to combat the dangers incident to poor ventilation and the presence of methane. Maintenance of high humidity throughout the mines was one of the first measures adopted, later to be superseded by rock-dusting. In the twenty years from 1907 on, many safety measures were developed and adopted, and several prizes were won, though the practice was crude by present-day standards. But in 1927, the company went to work in earnest, and organized a Department of Safety with adequate personnel and with authority to enforce all approved rules for the prevention of accidents and the preservation of company property. All plans for new construction work, changes in mining systems, and proposals for the purchase of new mining equipment had to receive the approval of this Department. A set of operating- and safety standards was written to govern the activities of all employees, and physical examinations for them were required.

Jan 1, 1938

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-'has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.' to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

CHARLES E. GUILLAUME,* .Sèvres, France written discussion?).-Referring top. 2052, experiments made at the end of the year 1884showed a remarkable agreement between the indications of various verre dur thermometers of which all the corrections had been determined with the greatest possible precision. The maximum deviations not attributable to the comparisons themselves were then about 0.002 to 0.003 degree. Much later, greater differences began to show. They were caused by the fact that the glassmaker-had modified the composition by adding to it a small quantity of lead. Efforts are now being made in France to obtain a regular, supply of glass made according to the old formula. The determination of the boiling point of sulfur made by Chappuis,1 444.5°, accords very well with the value noted on p. 2054. The International Committee of Weights and Measures and the General Conference have already considered the future abandonment of the hydrogen scale in favor of the thermodynamic scale. The hydro-gen scale appears to be, in their estimation, a transitory one, happily so closely approaching the final scale that no correction should be necessary for all measurements of temperature made during the last 30 years.

Jan 12, 1919

By R. Gilman Brown

Mines are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique gcological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.' On the other hand, this output has beeu mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness from 0.5 in. of ('specimen rock" to 30 ft, of clay and quartz; distributed through a zone about 2,000 ft, in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a

Jan 1, 1908

By HOMER L. WILLIAMS

WHILE some of the mining companies have been pumping a small amount of water for some time, it is only in recent years that large quantities of water have been encountered in the Tonopah district. The water appears to be in different zones or belts so that the draining of one property does not necessarily affect the one adjoining. Consequently, each company has its own pumping plant and its own conditions. The companies panes handling the largest amount of water are the Tonopah Extension Mining Co., Halifax Tonopah Mining Co., West Tonopah Consolidated Mining Co., and Great Western Consolidated Mining Co. The Halifax shaft is on the eastern end of the district and the other three properties on the western. The ore-bearing formation occurs at greater depth on -the eastern and western ends, hence the water problem in these properties.

Jan 1, 1921

By T. G. Lovering

Nonparametric statistical tests have practical application to many geological problems because, unlike the standard statistical tests, they do not require assumptions regarding the form of the population frequency distribution. Many of them do not even require that the variable be susceptible to numerical measurement. These tests are useful either 1) for geological data representing population distributions of unknown form, or otherwise not meeting the requirements for standard parametric tests; or 2) for sample attributes that cannot be measured but only ranked in order of relative magnitude. The application of two such tests will be illustrated. The Kolmogorov-Smimov test will be used to test for significant differences in copper distribution in samples of two rock types; the Spearman rank-correlation method will be used to determine whether there is a significant association between intensity of rock alteration and copper content of the rock. Nonparametric tests are, in general, quicker and easier to perform than the corresponding parametric tests, and they may be applied to a greater variety of data. They are not as powerful as the standard tests if used on data to which the latter are applicable, and computer programs utilizing them are not generally available. The use of standard or parametric statistical procedures for the interpretation of measured geological data is familiar to most mining engineers and explora- tion geologists. The computation of product moment correlation coefficients on sample assays for more-than one component is already standard procedure in some company operations, as is the use of Student's F test and Snedecor's F test for the comparison of means and variances of sample groups. The application of these three tests is limited by the prerequisites that the samples must be random, independent representatives of normally distributed populations and that the variables involved must be measurable. If such tests are applied to data which fall short of fulfilling these prerequisites, then the probability level attributed to the computed statistic is invalid and the conclusions based thereon may be erroneous. A number of nonparametric, or distribution free, statistical tests have been developed for use with data which are not amenable to standard parametric procedures. These tests have been widely used in the behavioral sciences such as psychology and sociology for some time, but their application to geologic problems is relatively new. Nonparametric tests may be grouped into two main categories: those which test for significant differences in a single variable by comparing either sample values with a standard value or representative values between two or more groups of samples; and those which test for significant association between pairs of variables in a single group of samples. The versatile chi square test, the Kolmogorov-Smirnov one and two sample tests, the Wilcox matched pairs signed ranks test, the median test, the Mann-Whitney U test and the Cochran Q test are examples of nonparametric tests with demonstrated or potential geological applications that belong in the first category. The contingency coefficient, Spearman rank correlation coefficient, Kendall rank correlation coefficient and the

Jan 1, 1963

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

By W. M. Wojcik, R. F. Kowal

Oxygen and sulfur distributions in commercial, 5-ton ingots of killed, medium carbon steel are described. Oxygen distribution is found to vary with deoxidation practice. Irregular distribution of oxygen within ingots makes necessary special precautions in sampling of rolled products for analysis of oxygen. Oxygen distribution is discussed in terms of recently published solidification concepts which had been successfully applied to simpler cases of segregation. These concepts have been found inadequate to explain observed oxygen distributions. Convective movements of the liquid metal, as determined by tracer elements, are shown to be capable of accounting for the observed distributions of oxygen. IN an effort to explore the origin of surface and subsurface imperfections in pierced steel products, a study of oxygen and sulfur segregation was made on ingots cast in open-top and hot-top molds. The results of our previous investigations1"3 have indicated the importance of the location and amount of oxide inclusions in an ingot. Inclusions close to the surface of the ingot have been found to contribute greatly to the formation of imperfections in the surface of finished products. This study of the effects of deoxidation and casting practice on segregation and the resulting oxygen distribution in ingots was initiated to determine the parameters controlling the location of inclusions in an ingot. Segregation of solute elements during solidification of low-melting binary alloys has been studied in the past.1, 5 Formation and growth of inclusions in iron melts have been studied under specific conditions."- In spite of these and other recent studies,10-12 segregation during solidification of commercial, killed steel ingots is not well understood. Consideration of solidification rates, of segregation during solidification of the chill, dendritic, and central zones, and of material balances for the segregated elements has indicated that a simplified theoretical solidification model is not adequate. However, the observed high oxygen contents in localized volumes of the dendritic zone can be rationalized if additional effects of convection currents in the ingots, precipitation, and rapid growth of new phases are considered. EXPERIMENTAL PROCEDURE Steelmaking and Processing. A group of nine killed. medium carbon steel heats having compositions listed in Table I have been studied. The deoxidation and mold practices used were varied to give a wide range of steel oxygen contents. The amounts of aluminum added to the ladle and the ingot casting practices (hot top and open top) were the main variables. The steel was made by a duplex practice in 160-ton tilting basic open-hearth furnaces. All nine heats were top-cast into 24 by 24 in. big end down, fluted molds, to a height between 60 and 76 in., using both open tops and exothermic hot tops. The deoxidation practice and the tapping and teeming details for each heat and ingot studied are given in Tables II and III, respectively. Hot-top practice is indicated by the letter H following the heat designation. Furnace and ladle temperatures were measured by standard disposable-tip, Pt/10 pet PtRh thermocouples. Teeming-stream temperatures were obtained as described by Samways et al.,13 by immersing a Pt/10 pet PtRh thermocouple, covered by a silica sheath, into the teeming stream under the nozzle. The output of this thermocouple was recorded with Leeds & Northrup Speedomax potentiometer. Calibration of the latter thermocouples was based on the freezing point of a pure iron/oxygen alloy (2795°F). The accumulated errors of measurements were within ±10°F. The thermocouple measurements were supplemented in this investigation by continuous recording of a ratioing, two-color pyrometer (Shawmeter), protected from smoke by a blast of clean air within the sighting tube, and calibrated to read with better than ±10°F accuracy. Following teeming of three heats, P, R, and T, tracer elements were added to the steel in the molds to obtain a record of the progress of solidification. As soon as the teeming stream was shut off, a 0.010-in.-thick steel can containing a mixture of crushed standard ferro-titanium and ferro-vanadium (0.05 pet of each alloy element) was plunged into the middle of the steel pool to a depth of 6 in. In about 30 sec no indication of the can or its contents remained. The surface of the open-top ingots solidified in 20 to 30 sec. A study of liquid metal movement and the precipitation of oxides was facilitated materially by use of the tracer technique as titanium has a low distribution coefficient between solid and liquid steel while vanadium has a high distribution coefficient.

Jan 1, 1965

By Thomas H. Leggett

IN speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining-practice, since this has been already well described both in the Transactions1 and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a. whole, marking its general development and the lines of its future progress. In a. paper entitled Deep-Level Shafts on the Witwatersrand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,3 presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (1:). 975): "In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discussed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy was vitally necessary for both 1 Gold-Mining in the Transvaal, South Africa, John Hays Hammond, xxxi., S17 to 855 (1901). R Engineering and Mining Journal, vol. lxxxv., p. 53 (1908). ' Trans., xxx., 947 to 987 (1900).

Jan 5, 1908

By J. J. Taber

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By Paul M. Tyler

MUCH has been said in print, and much more that was unprintable, about burdensome controls, taxation, and multiplying restrictive, regulatory, or taxing activities of the Federal Government, but not so much has been said about ways and means whereby the Government can and does render economic assistance. Economics has been defined as the study of men earning a living, and economic assistance to industry as well as to individuals properly should take the form of helping enterprisers to help themselves rather than charity. Proposals to have the Government play Santa Claus must be examined carefully if -only to avoid undue favoritism to politically important persons and downright venality by potentially crooked public officials. Thomas Jefferson is credited with the remark that the best government is the one which governs least. Paternalism is abhorrent to most Americans.

Jan 1, 1947

By Arthur B. Foote

THE ball mill has superseded stamps for the reduction of gold ores in most of the recently designed plants, partly because stamps are not suited to die fine grinding required for flotation, and partly to save space and construction cost. Experience with these new mills seems to confirm the idea that it is more difficult to recover bold from a ball-mill product than it is when stamps are used for crushing. Microscopical examination of particles of gold that have passed through a ball mill show that the gold has been pounded into exceedingly thin flakes coated with a talcy surface, making it more difficult to save by amalgamation, flotation, or concentrating. Bearing in mind that gold is extremely malleable, it seems reasonable that this should be so. Contrast the action in a stamp battery, where the crushing is by impact in the presence of mercury, to the grinding and rolling under pressure in a ball mill. It is well known that a better recovery can be obtained by panning or amalgamation from a sample of ore that has been crushed by mortar and pestle than from one reduced on a bucking board.

Jan 1, 1937

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By C. H. Herty, J. L. Keats

In the literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete data as possible on all the factors that affect the elimination of metalloids were obtained. The Test Heat The test heat was made in a standard 100-ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y., on January 17, 1922. The Charge—Scrap.—The scrap consisted entirely of rail-heat butts, selected from a number of heats made the week before the test. The average analysis of the scrap was calculated from the analysis of these heats and from the weight of scrap from each heat. Pig Iron.—Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample. Other Materials.—Weights of dolomite, ore and spar were obtained by weighing a quantity of each just before the test and weighing the amount of each left after the heat was completed. The limestone. was weighed on the charging pans. Coal for recarburizing, ferromanganese, ferro-silicon and aluminum were weighed out as used. All these materials were carefully sampled before the test was begun. Coal consumption at the producers was obtained by getting the average capacity of the hoppers that fed the producers, and then counting the number of hoppers of coal used during the course of the heat. Products Steel.—The steel made was rolled into billets, the rolling properties being very satisfactory. The weight of steel was obtained by taking a

Jan 1, 1926