Search Documents

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By J. E. Johnson

Discussion of the paper of Mark A. Amnion, presented at the Cleveland meeting October, 1913, and printed in Bulletin No. 70, October, 1913, pp. 1167 to 1 79. J. E. JOHNSON, JR., Ashland, Wis.:-Mr. Amnion's paper is of great value and it is not with any desire to reflect. on it that I wish to make some comments on the use of the scleroscope. We obtained one on trial some months ago and made very extensive tests with it, but without getting very satisfactory results. The readings on good car-wheels and bad ones were just about the same, but the factor in its use most likely to produce erroneous results is a variation in the thickness of the specimen being tested. In order to find out something on this subject we cut a thin disk, about -1,: in. thick, off a brass rod; then one 0.25 in. thick, and another about 1 in. thick, put the surfaces of all in about the same condition and tested them with the scleroscope. The readings varied widely; the resilience of the anvil evidently entered to a very high degree on thin pieces. By putting a soft cushion between such a thin specimen and the anvil, and forcing it up against the tube, the softness of the cushion cut off the resilience of the anvil and the results were more like those of the thick specimens. After a thickness of 1 in. was passed, the specimen seemed to have mass enough so that the resilience of the anvil no longer played an important part, and above that thickness results on different materials would be comparable, even though the thicknesses differed. But in order to get comparable results on thin specimens the thickness of those being tested should be the same. I should like to ask how the variations introduced in this way were overcome, so as to get strictly comparable results. Mr. AMMON :-.I have not had much experience in that, but the scleroscope is simply an indication of the surface harden-

Dec 1, 1912

By Walter Miller

Advancement in engineering in the refining industry during 1933 might be likened to the jagged flame of a poor wick-test kerosene—a few outstanding high spots, but not broadly spectacular. Economic conditions were unsatisfactory for the first six or eight months, but the improvement in the latter part of the year had some immediate effect in stimulating new designing and building. The national legislative program involving the industry drew the attention of executives away from petroleum technology to some extent. The National Recovery Act, and its offspring, the Petroleum Code, demanded deep and continued study to put the machinery into smooth motion. From a purely technical engineering stand, therefore, the emergency measures might be considered a temporary brake on progress. The ultimate effect, if the whole industry can get back "out of the red," may well be a more than expected advance. Of course, petroleum technologists and engineers, including both those engaged within and those busy in designing and building for the industry, continued their efforts, and much of the results of their work will undoubtedly see the light of day under the improved economic conditions, which bid fair to stay with us. There was little improvement during 1933 in atmospheric distillation, sweetening processes, or furnace design, but experimentation during the year on these subjects may materialize into distinct advances. The trend toward compact distilling and fractionating equipment, especially in the Appalachian district, deserves noting. A number of refineries in that district replaced obsolete shell still units with up-to-date tube stills and efficient fractionating towers, both for the better separation of lubricating fractions from the crude and for improving the boiling range of the gasoline. A number of small skimming and topping plants in flush fields, such as East Texas, which felt the pinch of production control, were forced to shut down, but the stronger among them are consolidating their positions by installing cracking equipment and in some cases more modern crude-distillation units. Motor Fuel For the first time in many years a reviewer is able to point to at least a temporary cessation in the competitive race in the manufacturing

Jan 1, 1934

By Robert Tally

UNDERGROUND fires have been common in the mines of the United Verde Copper Co. for the past 22 years. The first fire started in the 300 Hampton stope in the fall of 1894, following a cave in that orebody. The soft and highly pyritic nature of the ores is responsible for most of these fires. Since ore characteristics, methods of mining and ventilation, have an important influence on mine fires, they will be described in this paper. Orebodies The ores are mostly chalcopyrite except on the upper levels where considerable chalcocite, black oxides and other secondary minerals occur. The orebodies are in the form of lenses and vary in size. Some are small, while others are several hundred feet in length by a hundred or more feet in width. These orebodies extend, in some cases, from the surface to the lowest levels of the mine and usually at a steep angle of inclination. There are three different classes of ores, classified in accordance with the gangue rock. The copper in all cases, except as above specified, is in the form of chalcopyrite. The largest and most important of these reserves are in a pyrite gangue. Next in order of importance are the schist ores and lastly the quartz porphyries. The pyrite, locally termed iron ores, average from 30 to 42 per cent. sulphur. The schist and quartz, porphyries vary from 3 to 25 per cent. sulphur. Mining Methods All the orebodies were worked by the overhand square-set method of mining prior to 1908; since then the cut-and-fill, shrinkage and mill-hole systems have been largely employed. But 15 per cent. of the total tonnage now extracted is from timbered stopes. Most off this is from the upper levels where the ore is soft, heavy and more or less broken to the surface. Large reserves of these ores are being conserved for more efficient methods of mining.

Jan 9, 1916

By J. H. Pratt

In a recent paper* on the origin of corundum associated with the peridotites of North Carolina, attention was called to the constant occurrence of the mineral, chromite, in these rocks. The field-data obtained during the preparation of that paper have been used largely in the present paper. During the past summer the general occurrences of chromite have been carefully studied, and those in North Carolina have been especially examined in the field. It is purposed to give, in this paper, the reasons why the chromite should be regarded as having been formed at the same time with the peridotites, having been held in solution by the molten mass of the peridotite, and crystallizing out among the first minerals as the mass began to cool. This theory is essentially the same as that advanced by me for the origin of the corundum associated with the peridotite rocks, and a similar line of reasoning has been used to substantiate the theory proposed. Investigations concerning the igneous origin of some of the ores have been materially aided, during recent years, by the skillful experiments of Morozewicz and Lagorio,§ and by researches that show us, more clearly, why we should regard a fused mass of rock as a liquid, having similar properties to an ordinary solution. These experiments have shown that a molten basic glass, similar in composition to the basic magnesian rocks, dissolves alumina readily, and that upon cooling, the first minerals to separate out are corundum and spinel.

Jan 1, 1900

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By Guy T. McBride

The 1970's have been considered a pivotal decade for the mineral industries. Undergraduate mineral engineering education is relevant to this theme; in particular, there are three interrelated problems: 1) The goals, and therefore the course requirements, of the under- graduate curricula are in question; 2) The unit costs of undergraduate education appear excessive to those who bear the charges; and 3) The present social ambience detrimentally affects the work attitudes and career motivation of both prospective and in-course students. Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development and production levels. Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of society and the profession.

Jan 3, 1973

By Richard L. Gordon, Charles J. Johnson

Electric power demand doubles about every ten years, and because of the associated burgeoning fuel requirements, power stations absorb over half of the coal output in the United States. Throughout the 1960's, demand for coal utilized to generate electricity grew at an average annual rate of 6.5% but coal producers held back greater expansion because they expected nuclear plants to proliferate faster than they actually did. Even so, the growth rate is expected to continue at the 1960's rate until at least 1976. The continuation of the 6.5% growth rate beyond 1976, however, will require additional orders for coal-fired plants during the early 1970's. In fact, plants consuming a total of 130 million tons of coal must be ordered in the next few years. If the requisite plants materialize, total 1980 coal output for electrical power generation will be approximately 600 million tons.

Jan 1, 1971

By C. G. Dunn, F. W. Daniels, M. J. Bolton

IN recent papers on interface energies in metals¹,² the concept of an equilibrium of forces has been used in the measurement of interfacial tensions. Mathematically the equilibrium of three forces is given by the relations: where the 2's are the interfacial tensions (interface energies per unit area of interface) of three phases or grains meeting at angles 21 22 and 23 (212 relates to the 1-2 boundary formed by grains 1 and 2;223 to the 2-3 boundary, etc.). If these relationships are valid, one can calculate relative values of the interface energies from measured boundary angles on specimens which have been brought to equilibrium. Since Eq 1 may be derived through a mathematical process of minimizing the grain boundary energy under the restriction that the ?'s be independent of boundary orientation: the concepts of surface tensions and equilibrium of forces are not particularly essential. To deal with the general case involving dependence of boundary energy on boundary orientation, it becomes desirable to drop certain concepts formerly held (namely that energy per unit area is identical with force per unit length or surface tension) and to use the energy concept alone. It is appropriate, therefore, to use E in place of ? in deriving and using the more general equations that express the anisotropic nature of the grain boundary energy. Herring3# ' recently has derived the required general equations using the principle of minimization of energy. Specifying the boundary orientations in terms of angles (4) measured with reference to crystal axes within the grains, Herring's equations take the form E23 + E21 cos?8 + E12 cos?2 — sin ?12 + sin?2-?E12/?12 =O [2] where the partial derivatives are measured in the direction of counterclockwise rotation of the boundaries. Eq 2 implies that an infinitesimal displacement of the triple point along the 2-3 boundary produces no change in the boundary energy. Similar equations apply for infinitesimal displacements along each of the other two boundaries. From such equations Herring obtains the following general relationship (1 + E1 E2) sin?8 + (E2 — E1) cos?3 ________ E38______________ = (1+ E2 E8) sin ?1+ (E3— E2) cos ?1 __________^5____________[3] (1 + E sin ?2, + (E1 — E8,) COS ?2 1 E28 where E1 = 1/E23- E25 and PC and c8 have similar expressions. It is apparent that Eq 3 reduces to Eq 1 when the c's vanish. Eq 3 also reduces to Eq 1 when the E'S are all equal. Shockley and Read' have pointed out one limitation to these equations. When E plotted versus 4 appears as an energy cusp, as their theory requires, for example, for the energy near a twin boundary position, then Eq 3 (and therefore Eq 1 also) no longer applies if one boundary is in the minimum energy position. One of the equations of form Eq 2, however, applies if the infinitesimal displacement is along the boundary associated with the energy cusp. From the foregoing treatment it will be apparent that equilibrium angles alone are not sufficient in general for calculating relative interface energies.

Jan 1, 1951

By O. G. Bell

While all of the Southwest Texas fields lie within the Gulf Coastal Plain this area may be divided into three subdivisions—the Coastal Plain zone proper, the Reynosa Escarpment zone, and the interior zone. The Coastal zone includes that strip adjacent to the Gulf of Mexico and . extending inland for a distance of about 60 miles and includes the Palo Blanco, Palangana, Piedras Pintas, Kingsville, Agua Dulce, Saxet, White Point and Refugio fields. The Reynosa Escarpment zone includes a Pliocene overlap over older Tertiary sediments lying west of the Coastal zone. The western margin of the Reynosa formation forms a more or less well-defined westward facing escarpment with which the so-called Reynosa Escarpment fields are indirectly related. These fields include those in eastern Zapata, eastern Webb, western Jim Hogg, western Duval, McMullen, Live Oak, Bee, Goliad and Victoria counties. The interior zone includes these fields west of the Reynosa Escarpment which are not in any way related to it and are on separate types of structure. Production data by fields and wells are shown in Table 1. Roma.—During 1928 the Texas Co. completed two small gas wells at 198 ft. on the Roma Structure near the town of Roma on the Rio Grande in Starr County. This gas is of no commercial importance but was used for fuel in drilling other deep tests on this structure. Three dry holes ranging from 3600 to 4200 ft. were drilled; then their No. 4 Guerra, the fourth deep test, was completed during December as a small producer of 37" Bé. oil from a sand at 3560 to 3590 ft. No production was marketed during December but arrangements were being made to handle the output from this well during 1930. This is the first commercial producer in Starr County. Driscoll.—In 1929, Robert Driscoll discovered gas on his Santa Rosalia Ranch in Duval County while drilling water wells. Two sands were developed, one at 2400 ft. and another at 2936 ft. and several gas wells were completed in each, ranging in volume from 15,000,000 to 40,000,000 cu. ft. and in reservoir pressure from 500 to 1,000 Ib. Early in January of 1929, Mr. Driscoll's No. 14 Fee was completed as a 50-bbl. oil producer at 2894 ft. Two other oil producers were completed early in 1929. Mr. Driscoll's death early in the year curtailed develop-

Jan 1, 1930

Discussion o f Papers. Meetings of the Institute offer opportunity for social acquaintance and exchange of ideas, for the--presentation of papers, and-for discussions. thereon ; also incidentally for viewing under especially favorable conditions mining operations and industrial establishments, and for hospitalities which demonstrate the brotherhood clue to kindred interests. Placing sociability prominent is not to be assumed as relegating other features of meetings to subordinate positions; but during about 40 years of membership in the Institute, the value of acquaintances formed (often ripening into close friendship), and the interchange of data, have frequently demonstrated that the social feature of meetings is of great and lasting value to the membership. Of a roll embracing 4,011 members, resident in all parts of our country, and scattered in various portions of the world, only a small fraction are able to attend meetings, even if the localities selected are alternately widely separated. Hence, the return which most members receive for their annual assessment of dues is limited to the publications issued, and the credit of being recognized as a. member of a great and worthy organization. The greater the value of the contents of our publication, the fuller the return which goes to members. While the Institute disavows responsibility for views or statements made ill papers which appear in its Transactions, the fact that these contributions, after passing proper censorship, are accepted by the Institute and spread before the world may properly be received by the writers as endorsements of their (the writers') ability to present a specific technical or industrial proposition worthy of being carefully read. But the mere presentation and publication of contributed papers falls short of fulfilling one important feature of our meetings. If the purpose is confined to having the writers' views, discoveries, theories, or methods published, this can be obtained through the technical or trade journals and magazines. The true value of a paper presented at a meeting of the Institute may often be gauged by the discussion which it encourages, although there are contributions of decided value which do not especially invite discussion. However, most Of the papers offered contain statements apt to encourage criticism or elaboration by others whose experience or knowledge, or both, assist in combating or endorsing statements made.

Jan 7, 1913

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

By C. E. Shoenfelt

The outstanding development in the Rocky Mountain region for 1937 was the discovery of oil on the Wilson Creek dome in Rio Blanco County, Colorado, in the Morrison formation of Jurassic age. This discovery opens up a vast territory to exploitation and definitely establishes the western slope of Colorado as one of the region&apos;s more important oil areas. In former years, a large number of structures on the western slope were tested dry in Upper Cretaceous rocks but are now believed to hold possibilities in older formations, and a number of such structures are in line for drilling in 1938.

Jan 1, 1938

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in I920, and subsequent developments have been described by E. E. Hunner,1 M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. [T] The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Besse¬mer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden¬-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be over-equipped and high depreciation charges will have to be absorbed.

Jan 1, 1942

By Ralph H. Sweetser

To control the slag in an iron blast furnace is to control the quality of the pig iron produced (and to a certain extent the tonnage), and to control the whole operation of the furnace itself, including a large part of the cost of production. The character of the slag is the determining factor in the character of the pig iron as to the controllable limits of sulfur, silicon, and, to a certain extent, the manganese; it has an influence on the proportions of combined and graphitic carbons.

Jan 1, 1935

By Ralph H. Sweetser

To control the slag in an iron blast furnace is to control the quality of the pig iron produced (and to a certain extent the tonnage), and to control the whole operation of the furnace itself, including a large part of the cost of production. The character of the slag is the determining factor in the character of the pig iron as to the controllable limits of sulfur, silicon, and, to a certain extent, the manganese; it has an influence on the proportions of combined and graphitic carbons.

Jan 1, 1935

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let&apos;s examine the two most harmful ones.

Jan 8, 1978

By Roswell Johnson

PENNSYLVANIA will be remembered, as long as oil is produced, as the cradle of the industry of petroleum in North America. It was on Oil Creek, near Titusville, Venango Co., .that Cola Edwin L. Drake, superintendent for the Seneca Oil Co., brought in the first commercial oil well on Aug. 28, 1859. Great difficulty was experienced in getting the well down to the producing depth of 69 ft. (21 m.) with the spring-pole system then in vogue for punching shallow water wells, so the novel expedient of driving an iron tube through the surface clays and quicksand was finally resorted to. The well had an initial yield of 25 bbl. a day on the pump, but soon went off, though 2000 bbl. were produced by the end of the year. With the Drake well a success, a young industry sprang into being, the rapid growth of which has been second to none in the country and the value of whose product is only surpassed by that of coal. For years the only producing territory, the Pennsylvania-New York field attained its greatest production in 1891, when the bringing in of the McDonald pool, between Pittsburgh and the West Virginia line, gave a total of over 33,000,000 bbl. At present the field, combined with West Vir-ginia and southeast Ohio, gives 25,000,000 barrels. GEOLOGY AND STRATIGRAPHY In general, the Appalachian field is a huge geosyncline, the axis of which runs roughly northeast-southwest, from north of the New York state line south through Brookeville, Kittanning, Pittsburgh, Washington, through the southwest corner of the state of Pennsylvania into West Virginia. Minor folding has accompanied or followed the dominant fold of the field, and it is from these structures near the Pennsylvania-West Virginia line and their influence on the accumulation of oil and gas that I. C. White, state geologist of West Virginia, obtained his evidence for anticlinal guidance of prospecting.

Jan 2, 1920

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-La alloy systenz has been studied by thertnal, tnzcrographic, and X-ray diffraction methods. It is churacterized by a liquid miscibility gap, a maximum solubility of about 20 ut. pct PM in y lanthunum and 19 at. pct PI* in 0 lanthanum, very little soluibility of lanthanum in the plulonium allotropes, and the absence of intermediate phases. THE existence of immiscible liquids in the Pu-La system has been reported by Schonfeld.1 A tentative phase diagram based on the results of thermal-analysis experiments has been constructed by Poole et a1 2 This diagram shows a liquid immiscibility loop with a monotectic at 77 at. pct La and 846°C. 7 lanthanum is shown to dissolve 20 at. pct Pu and to decompose by an inverse peritectic reaction (y La = L , + p La) at about 82 at, pct La and 833°C. The ß lanthanum solvus was not determined, but the thermal work indicated a maximum solubility of 16 at. pct Pu in ß lanthanum. The present investigation has defined the solubility limits of plutonium in y lanthanum and 0 lanthanum, and, with the exception of minor discrepancies, has verified the results of Poole et al. 1) EXPERIMENTAL The electrolytic plutonium melting stocks were better than 99.9 wt pct pure, the main impurities being 90 ppm Fe and 50 ppm W. The lanthanum melting stocks, supplied by Research Chemicals and the Cerium Metals Corp., were about 99 wt pct pure, the main impurity detected by our spectrochemical analysis being 2000 ppm Fe. The components for each alloy button (-5 g) were weighed on an analytical balance and were melted together in a conventional arc furnace. If no significant weight loss occurred during melting, the as-weighed

Jan 1, 1968

By H. K. Shearer

Drilling for oil and gas in Arkansas in 1934 showed more activity than in any year since 1929; with a total of 96 completions, including 36 oil wells, 1 gas well and 59 dry holes. Of the producers, the lone gas well and 35 oil wells were in old fields, and one wildcat producer opened a new pool. Of the dry holes, 16 were in or near fields and 43 were wildcats. The total reported initial daily production of the oil wells was 9013 bbl., averaging 252 bbl. per well. Active drilling operations numbered 65 at the close of the year, compared with 26 at the beginning.

Jan 1, 1935