Search Documents

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By W. G. Pariseau, C. H. Schmuck, Fei Duan

The Homestake Mine is located in steeply dipping Precambrian metasediaents, an environment common to a number of world class ore bodies. Development of a pronounced plane of schistosity raises a question concerning the importance of anisotropy to the design of vertical crater retreat stopes. Little is known about the actual influence of elastic anisotropy in such -circumstances; even less is known about strength anisotropy. A cautious step- by-step approach was therefore taken towards a numerical assessment of the role of anisotropy in the analysis of stress and stability. The sequence of analyses begins with elementary test problems for computer program checks and proceeds to the analysis of a study stope area between the 6950 and 7100 Levels of the Homestake Mine. Anisotropy (orthotropy) is important at the Homestake Yine. No simple guidelines for evaluating in advance the need for plastic and strength anisotropy in design analysis appear to be forthcoming, ;o that some physical properties testing is necessary where the question is in doubt

Jan 1, 1984

By Thomas Leonard Watson

I. Historical. Barite has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. Geographical and Geological Distribution. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State—namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties: Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties—Bedford, Louisa, Pittsylvania, Russell, and Tazewell—but in the first two counties named there was no production, the work being solely development.

Jan 1, 1908

By Aaron J. Miles, Eugene A. Stepenson

The pressure distribution in a producing oil or gas reservoir has been obtained mathematically in a limited number of special cases where the boundary of the reservoirs are simple geometric figures with the wells conveniently located within them. Using some of the previous work as a basis, it can be proved that a number of additional problems of pressure distribution can be solved by use of soap film. This method is particularly applicable to a reservoir drained by a number of wells, or to a reservoir of irregular shape, or to both. Since this method obtains the pressure distribution, it also establishes the drainage boundaries of the wells. This paper derives the analogy between the equation representing the pressure distribution in a reservoir and the equation of the deflected membrane. It also describes the apparatus and the method of operation. The experimental method is employed to solve a problem whose mathematical solution is known and the results compared. These are found to be in good agreement. The method is applicable to any homogeneous liquid, compressible or incompressible, or to a gas, flowing in a reservoir of uniform thickness, permeability and porosity. The flow state may be either the steady state or the transient state wherein the density or pressure of the fluid in the reservoir declines at a constant rate. PRESSURE-DISTEIBUTION PBOBLEM Fluids encountered in the oil reservoir are compressible and expand and move toward the drilled hole where the Dressure is lowest. The loss of fluid from the reservoir lowers the pressure in the more distant parts of the reservoir, permitting the fluids in these parts to expand and move toward the well. The area around the well affected by drainage is increasing continuously, and the density, pressure, and velocity of flow

Jan 1, 1938

By N. R. Tipman, G. E. Agar, L. Paré

The flotation chemistry of the commercial INCO matte separation process was investigated. The slow cooling of Bessemer converter matte forms discrete phases of Cu2S and Ni3S2 and a Cu-Ni alloy. After magnetically removing the alloy, the Cu2S and Ni3S2 are separated by flotation at pH 12.4 (saturated lime) using diphenyl guanidine (DPG) as both collector and frother. DPG has been used exclusively in this flotation process because of its unusual selectivity for copper minerals. The surface product resulting from chemisorption of DPG onto theCu2S was identified as the double salt CU(DPG)2SO4.CU(DPG)2(OH)2. The adsorption followed Langmuir behaviour up to a monolayer coverage. In the absence of DPG, the rapid adsorption of oxygen by Cu2S in flotation pulps was observed. The surface product was identified as the insoluble basic copper sulfate CuS04.3Cu(0H)2 with the production of sulfate ion. In the presence of DPG, the oxidation reaction appears to be suppressed. The frothing properties of DPG and commercial frothers were compared. DPG is not a powerful frother. Batch flotation tests confirmed that DPG is a highly selective collector when compared to most sulfhydryl collectors.

Jan 1, 1976

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Dispersion-containing titanium-copper alloys were prepared having mean free paths varying from 1.0 to 9.7 P. Tensile studies at room temperature and at 1000°F showed that little or no strengthening occurred when the mean free path exceeded 3 p. However, at lower values of mean free path appreczable strengthening was observed. A considerable amount of strengthening also resulted from copper in solid solution. DURING the past several years, an increasing amount of study has been devoted to dispersion hardening, an alloying process in which increased strength is obtained through the addition of a ran-

Jan 1, 1961

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By L. C. Brown, E. B. Hawbolt

If a single-phase alloy is rapidly cooled such that insufficient time is available for an equilibrium transformation to occur, the high-temperature phase may be retained to room temperature or may undergo a massive or martensitic reaction. The massive or martensitic product develops without a composition change and usually has a crystal structure approximating an adjacent equilibrium phase. The characteristics of a massive transformation are intermediate between the equilibrium reaction in which long-

Jan 1, 1969

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By Donald H. Yardley, A. Aly Selim

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits, and the cost of producing it as a function of the deposit parameters. The economic simulation model includes programs for fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cut-off grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various hypothetical properties having the same area and different ore thickness shows that the effluent solution cut-off grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. It is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation.

Jan 1, 1979

By Arthur S. Dwight

We author of this historical chapter will perhaps be criticized for limiting his subject to the history of the blast furnace in lead smelting, and especially to the part it played in the great custom ore-smelting business which for three decades or more was the means of opening up vast mineral treasures and practically dominated the mining industry in the Rocky Mountain region of the United States, in Mexico and in Canada. The men of that era shared the romance and the thrills of mining, and bore their part as pioneers in the building of the great West. The present writer was too young to participate in the first of the three decades mentioned, but immediately thereafter came under the apprenticeship of some of the men who had worked out the early metallurgical problems of the industry, became personally acquainted with most of the others of that group, heard the tales of early experiences, successes and failures, the gossip of the frontier and mining camps, from all of which there remain embedded in his mind clear impressions of the outstanding personalities of that time. That is the background against which the fifty years of intimate contact with the mining and smelting business and his own experiences as metallurgist stand out in his memory, and it is hoped that the gentle reader may understand and approve his desire to rescue from comparative oblivion the fundamentally valuable results accomplished by these fathers of the industry. It will be the purpose of this chapter first to narrate the general history of the growth of the industry; second, to pay tribute to some of the pioneer metallurgists, and third, to discuss some of the salient points of the metallurgical practice at different periods, to illustrate the technical progress of the art. The series of eight Annual Reports of Rossiter W. Raymondl,† U. S. Commissioner of Mining Statistics from 1869 to 1876, contain most of the available information about the early smelting operations in the Rocky Mountain region, and much is in the early volumes of the Transactions of the American Institute of Mining Engineers. The monograph by S. F. Emmons2 though not published until 1886, contained an elaborate description of the smelting works operating in 1879. Otto H. Hahn3 wrote a valuable paper in 1883, on smelting prac-

Jan 1, 1937

By D. M. Thayer, P. B. Linkson

High intensity wet magnetic separation methods have received much attention in the search for alternative and effective methods to treat weakly magnetic minerals. This paper examines the incorporation of such techniques in the beneficiation of a non-sliming specular Michigan Hematite. The dependence of separation efficiency and beneficiation of specular hematite on various parameters controlling the operation of such a device is investigated experimentally. Particular attention is focused on particle size limitations imposed in these separations. In light of these data, metallurgical balances are presented and an attempt made to rationalize the various models suggested in the literature.

Jan 1, 1982

By N. S. Stoloff, J. N. Mushovic

Age hardening response of a Mg-Th-Zr alloy has been studied at temperatures in the range 60° to 450°C. Transmission microscopy revealed clustering of thorium atoms at low aging temperatures, supporting a previous report of GP zone formation. Peak strengthening, which is observed at 325°C, is due to the formation of a coherent, ordered, DO19 type superlattice structure, of Hobable composition Mg3Th, as plates parallel to the matrix prism planes. These plates later reveal a Laves phase structure of composition Mg2Th. The equilibrium Mg4Th phase begins to precipitate in two different forms at an early stage, competitively with the Mg2Th plates. RECENT work on the Mg-Th system indicated that, unlike most magnesium-base alloys, complex precipitation phenomena may be occurring. The partial phase diagram of the Mg-Th system indicates that an equilibrium phase, Mg5Th, is the sole intermediate phase.' sturkey,' however, has reported, using X-ray and electron diffraction techniques, that a metastable fcc Laves phase, Mg2Th, precedes the formation of the equilibrium compound, which he identified as closer in composition to Mg4Th. Murakami et al.3 reported that the equilibrium phase precipitates preferentially on grain boundaries and dislocations in a Mg-1.7 wt pct Th alloy; Kent and Kelly4 aged a more dilute alloy, Mg-0.5 wt pct Th, for 4 days at 220°C and found similar results. In addition, they reported that a platelike phase with a structure close to that of the magnesium matrix forms perpendicular to the basal plane and is probably ordered. Research on a Mg-4 wt pct Th alloy by electrical resistance measurements and transmission electron microscopy has suggested that GP zones may form at low aging temperatures.3 However, the electron micrographs purporting to show this phenomenon were not conclusive. In view of the fragmentary evidence concerning the nature of the precipitation processes in the various Mg-Th alloys, an aging study was undertaken to clarify the characteristics of the various precipitates which form and to correlate the mechanical properties of the system with the direct precipitate-dislocation interactions. The latter results are presented elsewhere.' The purpose of this paper is, therefore, to discuss the precipitation sequence in this system. EXPERIMENTAL PROCEDURE Sheet stock (0.060 and 0.010 in. thick) of a commercial Mg-3.93 wt pct Th-0.42 wt pct Zr alloy (designated HK3lA) similar to that studied by sturkey2 was supplied through the courtesy of Dr. S. L. Couling of Dow Metal Products Co. Zirconium does not enter into any precipitation reactions,' but is present primarily as a grain refiner. The alloy was chill cast, warm rolled to 0.090 in. thick stock, and then finally reduced by a combination of hot and cold rolling. The alloy chemistry is given in Table I. This material was solution treated at 580°C for 4 hr in a dry CO2 atmosphere, and then water quenched. Material in this condition was fairly clear of precipitate particles and was fully recrystallized. Aging at temperatures less than 200°C was accomplished by immersing the alloy in a silicone oil bath; for higher temperatures, aging was done in a salt pot. Age hardening treatments were conducted at 60°, 80°, 105°, 135°, 160°, 250°, 325°, 350°, and 450°C for times ranging from 5 min to 400 hr. Hardness tests were performed on chemically polished 0.060-in.-thick blanks of solution treated material which were aged at the various temperatures for increasing lengths of time. For aging temperatures above 150°C the Rockwell Superficial 30T scale was employed, while samples hardened at temperatures below 150°C were monitored with the 45T scale. Each data point consists of at least three separate readings. Yield stresses also were measured at room temperature on both 0.060 and 0.010 in. sheet specimens aged at 325°C. The aged foils were thinned by the window method in a solution of 80 pct absolute alcohol and 20 pct concentrated perchloric acid (70 pct) maintained at 0°C. A stainless steel cathode was used and the applied voltage was 10 to 15 v. Thinned samples were rinsed in distilled water and pure methanol. After the me-thanol rinse the thin foils were quickly dried between filter paper. Foils prepared by the above method were examined in a Hitachi HU11B electron microscope operating at 100 kv. RESULTS A) Hardness. The hardness data are depicted in Figs. 1 and 2. Peak strengthening occurs at 325°C after aging about 6 min, see Fig. 1. Significant strengthening is achieved also at 350°C, but aging at 450°C produces only softening. The stepped curve at 250°C indicates that a complicated precipitation process may be occurring at that temperature. Fig. 2 suggests that at least two hardening mechanisms exist since the lowest temperature hardness peaks are displaced to the left of the peaks obtained at 135° and 105°C. A great deal of scatter is observed at long times in all cases due to magnesium surface degradation caused by the silicone oil bath. B) Identification of the Strengthening Precipitates. The structure formed atlowagingtemperatures (c10O°C) was not clearly resolvable by transmission microscopy. The only bright-field evidence for a change in structure was a mottled appearance which could be observed at extinction contours, as shown in Fig. 3(a), and the disappearance of this effect when dislocations produced under the influence of the electron beam passed through the matrix, as noted in

Jan 1, 1970

By F. C. Blickensderfer

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-On your trip today through the Inspiration and Miami mills you have seen in actual operation the machines which represent the changes adopted in grinding methods in the Miami district from the beginning of operations in March, 1911. In one section of the Miami plant are three Chilean mills not yet discarded, representing the first machines adopted. In another section, pebble grinding is still in operation, while in the balance of the plant, pebbles have been replaced with iron balls. In all cases these machines are handling a feed which is the product of roll, grinding down to about ¼ in. in, size. The latest step in grinding in the district, You saw at the Inspiration plant, where in Marcy mills a filed, the larger pieces of which remain on a 2-in. opening, is being reduced in one operation to a product of which only about 3 per. cent. remains on the 48-mesh screen. A detailed comparison of the methods used at the two plants would be very instructive but our own work at Miami has not yet reached a point where such a comparison is possible, the reason being that our final product is not yet fine enough. By means of larger Hardinge mills operating in closed circuit with Dorr classifiers soon to, be installed in one section of the plant, we hope to obtain, under properly balanced operating conditions the same end result as at Inspiration. It, might interest you, however, to know some of the results we have obtained here by the substitution of balls for pebbles. With pebble grinding, using three 8-ft. by 22-in. mills, followed by one 8-ft. by 66-in. mill for regrinding the coarse product of the primary mills, we handled 636 tons per 24 hr. in one section of the plant. Substituting balls for pebbles in the first operation and using two mills in place of three we obtained a tonnage of .714 tons to the section. With the use of balls both in the primary mills and in the regrinding mills, the tonnage for one section was raised to 822 tons per day. Coincident with this increase in tonnage, we also obtained a greater efficiency. The use of pebbles in all mills showed 21.5 per cent. plus 48-mesh material in the final tailing, which figure was reduced to 13.9 per cent. for balls followed by pebbles, and to 4.6 per cent. with the use of balls both in the primary and regrinding mills.

Jan 12, 1916

By P. G. Shewmon, J. Y. Choi

The surface-diffusion coefficient for , has been measured on (111) and (100) surfaces of copper from 1000" to 620°C. D,(Ge) on the (111) is two to three times that on the (100) as was found earlier for copper and gold on copper. D, (Ge) on both (111) and (100) is about thirty times that found for gold or copper tracers on the same surfaces, while in the temperature range where both D,(Ge) and Ds(Au) have been measured the activation energy for germanium is the same as that for gold. The apparent activation energy for Ds(Ge) is not a constant, but decreases with temperature. In a recent paper we reported on the application of a new tracer technique to the determination of the surface-diffusion coefficient (D,) for gold and copper on (111) and (100) surfaces of copper.' In this paper, we shall give the results obtained when the same technique was used to measure Ds for germanium on the (111) and (100) surfaces of copper. In addition to providing data on D., for an additional element on copper, the longer half-life of germanium (275 days) meant that Ds could be measured down to a much lower temperature and thus over a much wider temperature range (1000" to 620°C) than was used in our gold-tracer work (1060" to 780°C) or copper mass-transport studies (1060" to 800). The apparent activation energy for D, (Ge) is essentially the same as that found for gold or copper in the same temperature range, though the values of D, (Ge) are thirty times greater than those found for gold or copper tracers. The most interesting new result found is that the apparent activation energy for Ds(Ge), and thus Do, definitely increases with temperature. Such a trend was much more apparent in Gjostein's mass-transport work on copper than in our own, though in an earlier paper we mentioned the difficulty of fitting all of our points with one straight line:= No real explanation of this is given though experiments done on grain boundary groove growth at various ambient pressures demonstrate unequivocally that vapor transport plays no part in the increase in activation energy with temperature.

Jan 1, 1964

By Frederic Lahee

THE purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexia1 fault zone, and to show how the apparently very irregular well logs in these fields may be used for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30° east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity river at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fault zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a down-throw on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults.

Jan 2, 1925

By C. F. Wang

Manchuria in General Manchuria, called the "Three Eastern Provinces" in Chinese, forms the northeastern corner of China and is bordered by Siberia on the north and northeast, and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty, and in more recent times it has been an arena for diplomatic maneuvering and commercial competition between the Russians, advancing from the north, and the' Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 2, 1918