Search Documents

By W. F. Wheeler

In the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the Survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. "Pure coal" has been defined by Mr. A. Bementl as ash- and moisture-free coal, and the use of this pure coal" as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume—first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results car] be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash

Jan 1, 1908

By Douglas Semmes

THE possible oil territory of Alabama can be readily divided into two regions, the Paleozoic area of the north, and the Coastal Plain province of Cretaceous and younger formations lying to the south. This latter area has received much attention in the last few years and has been described by a number of writers.1 Although the possibilities of the Cretaceous series have been much emphasized by recent writers, the fact remains that the two or, possibly, three localities where oil or as have been found in, anything like paying quantities are confined o the area of Carboniferous rocks. Moreover, almost all of the oil seeps and a good percentage of the gas seeps are confined to this area .2 Topographically, as well as structurally, the Paleozoic area can be divided into three rather well defined provinces: (1) The broad, open Coosa Valley lying adjacent to the crystalline oldland, with comparatively little relief, except for occasional longitudinal ridges and rather intense folding; (2) the plateau region of horizontal or gently warped Pennsylvanian strata broken by occasional anticlinal valleys aligned northeast and southwest, outliers of the Coosa Valley proper, in which

Jan 3, 1920

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By E. I. Salkovitz, F. W. von Batchelder

AS Slawson1 and others have already shown, from a geometrical view twinning in the diamond structure may be considered as a reflection across a (111) plane or as a reflection across a (112) plane. An analysis by Ellis and Treuting2 showed that the twinning plane must be the (111) plane, but that a twin might have lateral boundaries along (112) planes. Earlier Slawson1 and Ellis3 had shown that only (111) twinning was present in diamond and germanium respectively. Since an ingot of silicon, 1 in. in diam and 1 1/2 in. long, prepared from Dupont silicon to which 0.2 pct Be had been added was available, it was examined for twinning. The ingot had been cooled slowly from the bottom. A section 1/16 in. thick was ground off from the bottom and then the ingot was sliced vertically through the center. Spectrographic analysis indicated only faint traces of iron and silver, in addition to the beryllium. The sample was first etched with a hot solution of 10 pct NaOH in water.and photographed. Back-reflection Laue patterns were made of the vertical and horizontal sections in the regions designated in Fig. 1. Orientations were obtained for each twin using the Greninger technique. Several regions of the same orientation were found; thus regions A and K were identical, similarly N and P, and C, G, J, and L. Knowing the angles between the traces of the twinning plane on the surface and the specimen axis, the indices of the twinning plane were deduced. In all cases the twinning plane was found to be (111); lateral boundaries, however, were found which were (112) such as the one indicated in Fig. 1. Therefore, as in the case of diamond1 and germanium' only (111) twinning occurs in silicon. We wish to thank Mr. Hino for the use of the ingot as well as for its metallographic preparation. References 1C. B. Slawson: American Mineralogist (1950) 35, p. 193. 2 W. C. Ellis and R. C. Treuting: Trans. AIME (1951) 191, p. 53; Journal of Metals (January 1951). 3W. C. Ellis: Trans. AIME (1950) 188, p. 886; Journal of Metals (June 1950).

Jan 1, 1953

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By Max Ball

AN intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies Which tend to confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. ORIGIN OF THE LAW Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb. 11, 1897 (29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims."

Jan 6, 1914

By Earle J. Klohn

Mining operations have been carried out in British Columbia since the time of the first settlers in the area. The early developments were mainly small volume, high-grade operations, producing small quantities of tailings wastes. In these early days the nearest stream was a logical first choice for tailings disposal. Where streams suitable for accepting the tailings were not available or where streams crossing the International Border could not be used for this purpose, the nearest convenient land site was selected for storing the tailings. Old tailings waste piles exist at many locations in the Province and are readily evident, for example, in the Princeton and Hedley areas. Figs. 1 and 2 are photographs showing the present condition of two of these old tailings dams. [ ]

Jan 1, 1972

By D. E. Hyatt

Many flotation plants practicing pyrite depression, mills leaching gold and silver ores, blast furnace facilities, and many metal plating shops share at least one common waste-water constituent of particular environmental concern-cyanide. In free or complexed form, cyanide ion is an emotionally and technically problematical reagent whose removal from water deserves attention. The initial consideration of the fundamental nature of soluble cyanides is followed by a discussion of decomposition or removal options for simple cyanide species. Complexed cyanide reactivity is discussed as it relates to ongoing or proposed methods for the decomposition or removal of soluble cyanides. New approaches to cyanide removal are discussed.

Jan 1, 1977

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term ''burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the features of high frequency, great strength and shallow depth of the beginning burst have been found. There are some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

By R. L. Sandefur

Professor Kim's excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate. Kriging is the procedure which finds the weighing coefficients which minimize the estimation variance [ ] is the variance of blocks like the one being estimated. wi is the covariance of the estimated block and the i-th sample. oij is the covariance of the i-th sample and the j-th sample. Ai is the weighing coefficient for the i-th sample. N is the number of samples. The formula for estimation variance can also be used to calculate confidence limits on blocks estimated by any linear combination of sample grades including: 1) Polygons a. Hole nearest block centroid is assigned weight 1. All other holes are assigned weight 0. b. Polygonal area weighing. The samples are assigned weights directly proportional to their polygonal areas of influence within the block. The weights sum to 1. 2) Inverse distance weighing. The samples are assigned weights directly proportional to the reciprocal of their distance to some power from the block centriod. The weights sum to 1. Often only holes nearer than a certain distance and/or the nearest hole in each octant is considered. If there is an antisotropy to the ore body, an elliptical transformation often gives more accurate results. The most popular inverse distance weighing function is inverse squared distances (IDS). 3) Simple average. All samples within a certain distance are assigned the same weights which sum to 1. As an example of the applicability of the above formula to any linear estimate an internal verification on copper grade of 665 blast holes on the 1040 bench at Utah's Island Copper mine is presented. Internal verification is simple and applicable to non-linear estimates as well. Any sample (drill hole, bulk, trench, or chip) is dropped out, the value of the dropped sample estimated and compared with the actual value. If this is done for all samples, a measure of confidence limits is obtained. Internal verification is used in Cominco's MEPS system4 and in the BLUEPACK system.5 Comparison of block values against estimates697 is not dissimilar to internal verification. Results of the internal verification are presented below:

Jan 1, 1980

By Paul Gordon, A. S. Iyer

Apreliminary investigation has been carried out on the annealing behavior of explosively deformed copper as compared to that of conventionally deformed copper, using hardness, stored energy, and the sharpening of X-ray spots on Debye rings as the measures of annealing. Some metallographic observations were also made. Two purities of copper were studied. The first was tough pitch copper obtained as a small piece from the guard ring of a sample explosively deformed to approximately 500 kbars.* The second consisted of mentedand deformed these samples quite badly so that only a few small fragments were available for the annealing experiments. As a result, little in the way of quantitatively significant data was gleaned from the measurements. However, several important qualitative differences between the annealing of explosively deformed and conventionally deformed copper have been observed. It is these effects which are described in this report. Fig. 1 presents the results of hardness and stored energy measurements during the annealing of the high-purity copper after explosive and after conventional deformation. The data for the conventionally deformed copper were taken from the work of Gordon;' in this copper it is evident that most of the stored energy is released concommittantly with the hardness drop. As shown in orddon's' investigation, these effect:: are definitely associated with recrystal-lization. In the case of the explosively deformed copper, on the other hand, a large fraction of the stored energy is released before any appreciable hardness change takes place. At 160°C about 40 pct, and at 170°C about. 80 pct, of the stored energy appears to have been released prior to the onset of softening, i.e., undoubtedly prior to recrystallization. In view of the facts that the hardness and energy measurements were made on separate samples and that there is reason to suspect that the intensity of the explosive deformation from sample to sample may not have been uniform, a check run was carried out in which both energq release and hardness changes were measured cnn the same sample. The results of this run, shown in Fig. 2, confirm the conclusion that much of the stored energy is released before the hardness begins to change appreciably. In an effort to obtain some idea of the activation energy associated with the early release of energy, a single callorimetric sample was annealed in two steps, first at 149.5"C and then at 159.5"C, Fig. 3.

Jan 1, 1962

By John D. Vincent, Howard W. Jacky

This chapter covers the normal problems encountered in the building of an ore concentrating facility. To produce such a facility In today's environment requires correlation by the engineers involved of geologic data, mine planning, scheduling, future planning, water resources, power, land availability, testing, design, start-up and environmental considerations. Of course, the program scheduling and character of the ore will determine the weight given to the above considerations in the final design and construction of the plant.

Jan 1, 1978

By J. B. Clark, F. N. Rhines

brittlement or notch sensitivity progressively increases. Further, in contrast to results obtained with the impact test, the notch strength for the large specimens does not reveal a 500°F embrittlement range. The notch sensitivity as determined with the 0.3-in. specimen of 4340 steel given the stepped austenitizing treatment has been discussed elsewhere. This quantity as measured for the 1.1-in.- diam notch tensile test and given in Fig. 3, is taken to signify that reduced notch sensitivity is encountered in the 600" to 800°F tempering range for specimens given the stepped austenitizing treatment. The stepped austenitizing treatment may, there- fore, be of use in promoting deeper hardenability for a 4340 steel while at the same time giving reduced notch sensitivity in the high-strength range in which this steel is now being used. Acknowledgments The work reported was supported by the U. S. Navy Bureau of Aeronautics. The authors are indebted to the Bureau of Aeronautics for granting permission to publish results of this research and to N. E. Promisel, H. Hessing, and J. Maltz for their interest.

Jan 1, 1958

By Richard P. Gerwels

Minas de Matahambre, a copper mine located 100 miles southwest of Havana, Cuba, has produced 10 million tons of copper ore since it was first opened up in 1913. During the mid-1950's the mine was producing approximately 1000 tpd and had attained a depth of 3600 ft. As shown in Fig. 1, the property contains three shafts: the No. 1 shaft, 2100 ft deep and located 2000 ft south of the No. 2 shaft, provided service to the 2100 level; the vertical 3600-ft No. 2 shaft handled all production to the 3400 level; the No. 3 shaft on the northeasterly fringe of the mining area was in a semi-active status.

Jan 12, 1960

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

By John F. Blandy

IT is not my intention in this article to consider this subject in the light of the geographer or geologist, but rather in that of the mining engineer, and to endeavor to show the necessity and value to him of studying the minor details of the field or district in which he may be engaged. I t has been said by a distinguished geologist that "the natural boundaries of the geographer are rarely described by right lines. Whenever they occur, however, the geologist may look for something remarkable." And again : " Physiognomy is no idle or doubtful science in connection with geology. The physiognomy of a country indicates almost invariably its geological character." Our country furnishes examples enough of the truth of these remarks, and in no part of it is it so beautifully illustrated as in our own State, which has been so ably described by Prof. Lesley in his admirable little work on the "Topography of Coal." As the great mountain lines become guides to the geologist in determining and mapping out the geography of the formations, so do the minor details of topography become guides to the mining engineer in conducting his explorations, discovering of dislocations, and determining the character of the deposits which are the object of his search. I t is therefore requisite that he should, whilst making his surveys, pay the strictest attention to every variation of the landscape and surface of the ground. Until he has mapped out every feature he may be unable to read the geological changes which may have

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

Australian research scientists at the University of Melbourne's Institute of Materials Research have discovered two methods of extracting metals from raw ore, using brown coal. The discoveries could lead to extensive new markets for the brown coal producers of Australia (boasting the world's largest brown coal deposits in the Latrobe Valley region of Victoria), the United States and West Germany. Research on the extraction processes began at the University's Department of Metallurgy in mid-1969 under the direction of Geoffrey Cullen, manager of the Materials Research Institute. In June of this year. Cullen announced that both metal extraction processes, using brown coal, had proven successful.

Jan 1, 1971