Search Documents

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By Norman A. Jull, A. L. Mular

Fundamentals of cyclones are reviewed briefly, where a typical cyclone is considered. Graphical cyclone data available in the literature have been converted to mathematical equations for convenience. Preliminary selection and design procedures for both cyclones and pumps are provided, and a sample calculation for a hypothetical grinding circuit is covered in some detail. In general, cyclone and pump suppliers should be consulted for definitive design purposes. Some cyclone suppliers currently employ digital computers for definitive design to ensure greater accuracy.

Jan 1, 1978

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By AIME AIME

FOUR separate groups of conveyors are installed in the Morenci Reduction Works as follows: (1) Ore-handling conveyors from the primary crushing plant to the coarse ore bin, from the coarse-ore bin to the secondary crushing plant, and from the secondary crushing plant to the ore bin in the concentrator plant. (2) Conveyors in the mill section of the concentrator plant. (3) Conveyors handling concentrate from the filter plant to the bedding plant, and from this plant to the smelter. (4) Conveyors handling flux and custom ore in the smelter crushing plant and to the bin at the bedding plant.

Jan 1, 1942

By L. R. Jackson, W. T. Lankford, K. F. Smith

ComMercial steel sheet is prepared by a combination of hot and cold rolling and annealing. This treatment usually results in more or less pronounced anisotropy. The anisotropy may manifest itself both as preferred orientation and in the manner in which impurities, segregations, and the like, are aligned in the sheet. The type of preferred orientation and the organization of impurities or segregations may affect the elastic moduli, the yield strength, the tensile strength, and almost always the amount of ductility in different directions. In any case, the most important directions concerned in the anisotropy are along the rolling direction, along the width direction, and along the thickness direction. Considerable data exist on the anisot-ropy of sheet steel as demonstrated by conventional tensile tests; however, few attempts have been made to measure the constants of plastic anisotropy and use them to describe the flow of anisotropic sheet under combined stresses. In this paper, evidence is presented indicating that plastic flow in anisotropic sheet can be described by the shear-strain energy flow theory provided that the anisotropy is properly taken into account. Materials Used in the Investigation Table I lists the sheet materials used in this investigation and describes the condition in which materials were tested. Direction, of Tests and Test Methods Two types of tests were run—tensile tests and hydraulic-bulge tests. Characteristic parameters of anisotropy were determined from the tension tests by methods which will be described later. In all cases, the tensile test pieces were cut from the same quarter line and adjacent to the bulge test pieces in the sheet in order to minimize

Jan 1, 1949

By H. N. Mead

In a reservoir when gas comes out of solution and rises, additional pressure is created because of the change in position of this gar in the bounded volume. If this pressure effect is not taken into account as a pseudo-influx ill mate rial balance calculations on reservoirs in which there is evolving gas, an error is introduced that is directly proportional to the length of oil column and amount of gas evolved and inversely proportional to the reservoir pressure. In reservoirs with small oil column this pseudo-influx is of little importance. The larger the oil column the more important the effect becomes. The most important application, however, will be for reservoirs with declining pressure in which increasing water entry has been indicated by material balance calculations. It could be that this indication is the result of the cited pseudo-influx and not water entry at all. This paper attempts to explain this phenomenon in relation to material balance calculations and prevents an approximate method of determining tile pseudo-influx. INTRODUCTION Only recently has the pressure-volume relationship of gas rising in a liquid appeared in engineering literature, although its effect has been discussed for several years—especially among engineers engaged in drilling operations. The writer published a paper in 1957 in which this phenomenon was examined in relation to blowouts in drilling wells.' Also, in 1957 Stegemeier and Matthews' authored a paper in which the relationship was presented with respect to pressure build-up tests when shutting in producing wells. In this paper the effect will be called "pressure inversion" which is descriptive of the phenomenon. Fundamentally, the effect just mentioned is the result of changing the position of a quantity of energy contained within the gas itself (as a result of its compression) within the bounded volume in which the gas exists. If the gas were allowed to expand "beyond all bounds" there could be no pressure inversion effect. This is because all of the energy contained within the gas as a result of compression would have been re- PRESSURE INVERSION A phase that has not been discussed in the literature is the effect of pressure inversion upon material balance calculations in reservoirs in which the reservoir pressure drops with reservoir withdrawal and is below the bubble point. This action releases solution gas which, after the critical gas saturation has been reached, will tend to rise and collect at the top of the reservoir. The pseudo-influx caused by this effect could be great enough in reservoirs of large oil column and high permeability to render invalid any analyzer studies made on them — if pressure inversion has not been taken into account. Most suspect would be those reservoirs with large oil column in which increasing water entry has been predicted but the bottom wells have not yet produced water. Example 1 Simply stated, this phenomenon exists in oil reservoirs because of the difference in density and expansibility between gas and oil. For example, if a bubble of gas exists at the bottom of a 1,000-ft column of oil having a gradient of 0.30 psi/ft with the pressure at the top of the column zero, the bubble of gas will be compressed to a pressure of 300 psi. If temperature and the combined volume of the oil column and the gas bubble remain constant, as the gas bubble rises in the oil column it will have the same volume and consequently the same pressure at any point. Under these conditions when thc bubble reaches the top of the oil column, the pressure will be approximately 300 psi at the surface and approximately 600 psi at the bottom of the oil column. If it is assumed that the oil is incompressible the pressures will be exactly 300 and 600 psi, respectively.

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By Donald W. Mitchell

MINE operators have a choice of several classifications of mechanical loaders. Within each classification there are many types and makes available. Table I lists loaders on which manufacturing data as to operating characteristics are available. This paper discusses the conditions met in a mine as they affect these characteristics. It is assumed that management will provide satisfactory engineering, supervision, power, maintenance, loader service within a concentration of workings, and a balanced working cycle served by balanced production equipment. These are factors which affect the optimum operational efficiency of a loader. The conditions which determine loader choice are:

Jan 5, 1951

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.' and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions'" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author's own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d'Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

By Marion Rice

The copper-mining district of Jerome, Ariz., is of such economic importance that the following brief notes may be of interest. The ore deposits are said by Ransome1 to be pre-Cambrian, and are contained in the pre-Cambrian schists of the region. In the vicinity of the mine (the United Verde) the schist stands nearly vertical and strikes a little west of north. At least three varieties are distinguishable—(1) a green rock, schistose on its margins but grading into massive material, which is evidently an altered dioritic intrusive; (2) a rough gray schist with abundant pheno-crysts of quartz, apparently an altered rhyolite; and (3) a satiny, greenish gray, very fissile sericitic schist that may be a metamorphosed sediment. The ore occurs in varieties (2) and (3), the main belt of dioritic rock (1) lying just west of the orebodies. The ore is said to follow as a rule the layers of fine sericitic schist. T. A. Rickard2 Says that the ore at the United Verde Extension mine is found at the contact of diorite and schist, that both diorite and ore are earlier than the regional metamorphism, and that the quartz porphyry ("rhyolite" of Ransome) is of post-Cambrian age. The material considered here, a part of which was gathered by the writer, came from four of the mines of the district, and its study was undertaken at the suggestion of Dr. Berkey of Columbia University. The field relations and exact locations of the different specimens are not known, but a microscopic study of the thin sections gave some evidence as to the origin of the ore, which will be discussed below. The indications are that both ore and porphyry were introduced at the closing stages of the metamorphism, this being in accord with Ransome's view of the genetic relation of porphyry and ore rather than with the opinion that the ore is related to the diorite. Certain field occurrences mentioned in the literature also support this theory. Rickard, in the same article to which reference has been made, speaks of a vein of chalcocite several inches wide at the contact of one of the porphyry dikes, and Provot,3 although he regards the porphyry as subsequent to the ore, says: "Acid dikes encountered underground should be followed as they have been found in practice to lead to orebodies."

Jan 1, 1920

By Frank Van Horn

INTRODUCTION IN June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examined. The results of these investigations show that bournonite (PbCuSbS3) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2Sb2S5) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (H2Zn2SiO6) was found at one mine and has never been recognized and reported from the district.

Jan 8, 1914

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By Sidney Powers

Discussion of the paper of SIDNEY POWERS and ALFRED C. LANE, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 535 to 548. N. L. BOWEN, Washington, D. C. (communication to the Secretary*). -This detailed study and. complete demonstration of differentiation as a result of the sinking of crystals has a great general significance in petrogenesis. If this action can be demonstrated in an effusive body, even though a very thick one, how can one doubt its possibility in large intrusive bodies? The authors speak of the sinking of augite and the rising of plagioclase but I should consider that they should depend entirely on the former action to obtain their results. It is true that in my experiments, to which the authors refer, a floating of crystals was in one case obtained, viz., in the case of tridymite crystals, but it must be remembered that tridymite has an exceptionally low density. Plagioclase crystals, on the other hand, are of nearly the same density as basaltic liquid. Under magmatic conditions they might be a little heavier than the liquid or a little lighter, we do not know which, but the margin would be exceedingly small and any motion resulting, whether upward or downward, would be correspondingly small in the usual case. For this reason I should think that the sinking of pyroxene should be considered probably the sole factor in producing the observed result, for which purpose it appears to be entirely adequate. The measurements of grain have also a certain significance in this connection. In the experiments referred to a difference of grain was obtained in different parts of the charge, which was entirely independent of the rate of cooling but connected with the fact that a sinking crystal does not depend entirely upon diffusion for the collection of its material from the surrounding liquid. The crystals which sank a considerable distance were therefore exceptionally large. Now in the Cape Spencer flow the augite crystals are normally (top and bottom) somewhat smaller than the plagioclase crystals, but in the layer somewhat below the middle,

Jan 5, 1916

By Edward H. Robie

SEPTEMBER usually being a fine month for motoring, we set out with our better half at the end of August in our Studebaker for points West. A combined business trip and vacation. The first night found us 392 miles away, at the Statler Hotel in Buffalo, and the next morning we revisited Niagara Falls for the first time in some forty years. The cataracts were as impressive as ever and certainly worth a day of any vacationist's time, instead of the half hour we could spare before going on to Chicago. The Centennial of Engineering, the hundredth anniversary of the founding of the ASCE, no doubt attracted the greatest gathering of engineers in history but still the attendance was disappointing to most of the forty or fifty societies that participated. Perhaps the time-the two weeks following Labor Day-was unfavorable. Few could afford to spend ten days away from home and business at that time of the year. Fall meetings of the AIME normally attract far more than the 300 that registered in Chicago. The technical program, however, was excellent, especially that arranged by the Minerals Beneficiation and Industrial Minerals Divs. The mineral industry papers of a more general nature that were presented as a part of the Centennial program on Monday and Tuesday of the following week were of high quality and offered by top names but had a meager audience. Undoubtedly the celebration brought engineers and engineering to the attention of millions of people. The pageant at the Museum of Science and Industry proved continuously interesting, showing the progress of engineering following the first use of fire. The show continued for many weeks. A special stamp was issued by the Government, which engineers might well use on their Christmas cards or other mail this year. After six days in Chicago we set out north, first visiting Fairbanks Morse in Beloit and Allis-Chalmers in Milwaukee. Will Mitchell's Basic Industries Research Laboratory is doing interesting work and being installed in more comfortable quarters. The next day at Ishpeming, C. W. Allen arranged for luncheon with a local group of AIME members and we then looked over the new surface plant of the Mather B mine, a model of modern functional design. Then on to a small dinner meeting at Calumet following cocktails at Endicott Lovell's attractive summer home on the lake at Point Mills. The new Memorial Union Bldg. at Houghton, where we were domiciled for the night through the courtesy of Roy Drier, is a beautiful modern addition to the college, a model of its kind.

Jan 1, 1952

By N. E. Rogen, N. J. Grant

AGE-hardening in nickel-chromium-titanium-aluminum alloys in the composition range characterized by the Nimonic alloys, is dependent upon the precipitation of the Ni3(AI,Ti) (y') phase.1 This phase is found to precipitate at about 700°C.1 Ni,Al is a face-centered-cubic ordered structure with a lattice parameter of 3.560 A. The atomic configuration is such that the aluminum atoms occupy the cube corners and nickel occupies the cube faces with titanium substituting for the aluminum preferentially. A maximum of three out of every five aluminum atoms can be replaced by titanium atoms in the -y 'phase.' When the solubility of the y'-phase is exceeded for titanium the T(Ni,Ti) phase is formed. The T-phase is an ordered close-packed hexagonal intermetallic structure which shows little solubility for the other elements in these alloys. The lattice parameter for T-phase is a - 2.5454 kr and c = 8.2900 kx units."

Jan 1, 1959

By R. H. Lee

So far as I am aware the references to the " kerosene blow-pipe" in the Transactions comprise only a skeptical opinion from Mr. Witherow (ix., 70), and accounts of the use of the blow-pipe by Mr. Witherbee (xiii., 675) and Mr. Gayley (xiv., 779), together with brief remarks by Mr. Weeks and Mr. Kennedy on Mr. Witherbee's paper. The subject can scarcely be considered novel, in view of these references, yet it is not so far exhausted that an additional account of the successful application of the blow-pipe would be out of place, especially if accompanied with some new details and a drawing of the apparatus itself, showing its simplicity and safety. Some time ago, owing to a variety of causes, my furnace was working very badly, the troubles culminating suddenly one morning in a chilled hearth, solid from the bottom to the tuyeres, with the exception of a narrow passage-way from above to the cindernotch, which remained open. Through this we continued to flush and cast, with the prospect of a long and troublesome siege, in working down to the iron-notch. At the end of two days matters had not greatly improved, and we seemed no nearer the desired result than on the morning of the chill, when, at the suggestion of Mr. Farrell, of Glamorgan, I decided to use the coal-oil blow-pipe; the intention being to cut a hole from the iron-notch up to the tuyeres, and then let the furnace melt out the chilled mass. In four hours from the time of starting, the hole was made and

Jan 1, 1887

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By T. L. McCall

This is a continuation of the paper on bumps presented by the late Mr. Herd in February, 1929. The seam worked consists of bituminous coal, 9 ft. thick, pitching 20°, and now under a depth of cover of 2800 to 3200 ft. Full particulars are given of two bumps that happened in November, 1931, with an interval of only 9 hr. between them. The first was a "district" bump affecting an area of 1000 ft. on the strike by 700 ft. on the dip and rise, beginning at a distance of 1000 ft. from the long-wall faces. The second, which caused much greater damage, was localized to two levels 200 ft. apart, in the area left undisturbed by the first bump next to the longwall faces. Observation stations had been established in the workings in 1931 and definite records were obtained on the flow of coal taking place from the edge of large pillars developed for retreating work, into the open roadways. The records also gave evidence that "advance weighting" or "underdraw " was affecting the coal at an average distance of 260 ft. in advance of the longwall faces. The author propounds the theory that the sandstone bed varying from 0 to 75 ft. in thickness and lying 14 ft. above the coal acts as a slab in distributing the superincumbent weight. The weight is thereby concentrated on the pillars in advance of the longwall faces and this load, in conjunction with a pavement strong enough to resist the reaction, leads to overstressing the pillars, which finally collapse suddenly, thus giving rise to this particular type of low side bump. The overlying sandstone bed, which is apparently a condition common to all coal mines in which bumps occur, is not necessarily a massive bed, as the thickness of this bed at Springhill in the area that has experienced these severe low side bumps is only 25 to 31 feet. A list of 43 minor bumps occurring in the past 2½ years is appended

Jan 1, 1934