Search Documents

By Robert B. Bossler, Parke A. Dickey

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By Parke A. Dickey, Robert B. Bossler

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By J. J. Beeson

The second part of the paper includes a detailed account of the processes of secondary-enrichment which have been effective in producing the disseminated ores. While both parts present new features, it is hoped that the discussion on secondary chalcopyrite and bornite may be of interest to those who are engaged in the study of secondary processes in other districts. The excellent work' Economic Geology of the Bingham Mining District, by J. M. Boutwell, was published in 1905. Since that time the extensive development work-surface cuts and underground drifting-of the Utah Copper Co. has made possible the collecting of samples for more detailed microscopic study. The writer has taken advantage of this fact and presents the following work, not as a criticism, but as a' continuation of the work which was begun by Mr. Boutwell. b. Acknowledgments.-The present study was undertaken at the suggestion of Dr. A. F. Rogers; to him, and to Prof. C. F. Tolman and Prof. S. W. Young, the writer wishes to express his thanks for criticism in the preparation of this paper. The writer also expresses his thanks to D. C. Jackling, Vice-President and Managing Director of the Utah Copper Co., for permission to publish this paper, and to William Spencer, D. W. Wadleigh, T. S. Carnahan, J. A. Caulfield, Percy Dayer, and Edward Norsefall, for the courtesies extended to him while a co-worker in the mines.

Jan 11, 1915

By George H. Ashley

Mining, including quarrying, dates back almost to the dawn of history, beginning almost with the beginning of what we call civilization. State surveys date back about 100 years. Evidently mining flourished for thousands of years before state surveys were thought of. Why should it not continue to flourish without state surveys? First, it may be noted that as mining and civilization were contemporaneous, so state surveys and the science of geology were almost contemporaneous. As recently as 30 years ago the United States mineral laws were interpreted to mean that coal lands in the public domain were only those lands on which workable coal outcropped. The half billion acres of public land underlain by .coal but on which it did not outcrop were treated as homestead lands and open to settlement. Just what did the science of geology do to or for the mining industry? Until geology arose rocks or minerals or ores were where they were found. Their finding might be accidental, or might be the result of deliberate search or prospecting. In open, rocky country, with little or no vegetation, as in parts of the West, prospecting served very well, though at an enormous expenditure of human time and effort, if not money. The old saying that every dollar's worth of gold taken from the earth has cost two dollars may largely be charged to the time value of the usual method of prospecting. Geology changed all that. The science is still young and it still labors under handicaps of immaturity and early errors. Geology, however, has gradually been discovering the relations and conditions under which the several mineral deposits occur. Its elaborate studies of exhausted or nearly exhausted mineral deposits has done for it what human autopsy has done for medicine and surgery. Perhaps in no field is this plainer than in the oil and gas industry. Note might also be made of several important coal fields in England and on the Continent, in which the coal is everywhere deeply buried. Passing over the long period of growth during the past 100 years, geology today is prepared to offer the mining industry: first, a knowledge of the geologic conditions under which most minerals occur and to explore

Jan 1, 1935

By George H. Ashley

Mining, including quarrying, dates back almost to the dawn of history, beginning almost with the beginning of what we call civilization. State surveys date back about 100 years. Evidently mining flourished for thousands of years before state surveys were thought of. Why should it not continue to flourish without state surveys? First, it may be noted that as mining and civilization were contemporaneous, so state surveys and the science of geology were almost contemporaneous. As recently as 30 years ago the United States mineral laws were interpreted to mean that coal lands in the public domain were only those lands on which workable coal outcropped. The half billion acres of public land underlain by .coal but on which it did not outcrop were treated as homestead lands and open to settlement. Just what did the science of geology do to or for the mining industry? Until geology arose rocks or minerals or ores were where they were found. Their finding might be accidental, or might be the result of deliberate search or prospecting. In open, rocky country, with little or no vegetation, as in parts of the West, prospecting served very well, though at an enormous expenditure of human time and effort, if not money. The old saying that every dollar's worth of gold taken from the earth has cost two dollars may largely be charged to the time value of the usual method of prospecting. Geology changed all that. The science is still young and it still labors under handicaps of immaturity and early errors. Geology, however, has gradually been discovering the relations and conditions under which the several mineral deposits occur. Its elaborate studies of exhausted or nearly exhausted mineral deposits has done for it what human autopsy has done for medicine and surgery. Perhaps in no field is this plainer than in the oil and gas industry. Note might also be made of several important coal fields in England and on the Continent, in which the coal is everywhere deeply buried. Passing over the long period of growth during the past 100 years, geology today is prepared to offer the mining industry: first, a knowledge of the geologic conditions under which most minerals occur and to explore

Jan 1, 1935

By Rudolph Gahl

RUDOLF GAIL, Miami, Ariz.-Since I wrote the paper on flotation which is in your hands, important developments have taken place, and, for this reason, I will try in a few words to bring it nearer up to date as far as the Inspiration plant is concerned. You, may have noticed that in the Inspiration concentrator, flotation is not solely relied upon for the recovery of the coarser material, but that flotation tailings are split into a sand and a slime product on drag classifiers. The sand product is treated on tables which thus supplement the work of the flotation machines. Extensive tests have shown, us that, if we wanted to, we could leave out these tables and substitute additional flotation machines, as they will make fully as good, if not a better recovery than tables on the deslimed feed, but the treatment would be more expensive, especially in view of the fact that oils are required which cost more than those which we are now using in our main flotation plant. We have, however, decided to apply flotation treatment to our table middlings. I would also like to add a few words regarding the treatment of oxidized copper ores. Although our experience shows that the addition of hydrogen sulphide and other soluble sulphides effects a very good recovery of copper carbonates with certain ores, we have not been able to prove that we could use it advantageously for the ore mixture which we are treating in our concentrator, and for this reason, have looked toward leaching for extracting the carbonate and silicate copper that we are losing now. Experiments in this direction are going on and are giving very encouraging results. It may interest you to hear that we intend to use limestone for the precipitation of the copper which goes into solution, as electrolytic precipitation seems to be out of the question on account of the diluteness of the resulting solutions, and precipitation by iron was rightly objected to on account of the unavoidable contamination of the water supply. We feel very hopeful about the success of our limestone precipitation which, if it holds what it seems to promise, will develop into a novel feature of copper metallurgy.

Jan 10, 1916

By H. Reginald Hardy, Y. S. Kim

Recent studies of inelastic behavior and acoustic emission in geologic materials further validate the concept that such materials may be considered to consist of an elastic media containing an array of pores and cracks. In the present paper this concept is investigated further by experiments in which the mechanical behavior of a number of geologic materials were studied in detail at low stress levels using ultrasonic pulse methods. Experiments were carried out on cylindrical test specimens of Indiana Limestone, Tennessee Sand- stone and Barre Granite under relatively low confining pressures (0-5000 psi). Analysis of data from these experiments indicated that there existed a low-level critical stress at which there appeared to be a transition in the mechanical behavior of the material. Under triaxial stress, results indicated that the differential critical stress was relatively independent of confining pressure, i.e., the mechanism responsible for the transition in mechanical behavior was governed by a maximum shear stress criteria.

Jan 1, 1971

By Charles A. Ashburner

The manufacturing and domestic consumers of anthracite are beginning to realize the fact more fully, that the coal purchased for any one year does not seem to burn so freely, does not fire with so little trouble, and does not last so long as that purchased during other years, or vice versa. Where coals of different sizes, or from different districts, are offered to the trade by the same or competing salesmen, the question suggests itself, which shall we buy ? Among housekeepers, who are the most numerous class of consumers, though on the smallest scale, distinction is seldom recognized among these anthracites. By other consumers the coals are grouped into those which, when burned, will produce either a white or a red ash, special qualities being arbitrarily attached to each. Others, again, know only of three varieties : (1) Those from the WYoming and LacKawanna fields, or the coals shipped from the northernmost basins over the railroads running through northeastern Pennsylvania direct to New York—notably, the Delaware. Lackawanna and Western, Delaware and Hudson, and Erie railways; (2) those shipped by the Lehigh Valley Railroad and the Lehigh and Susqaehanna division of the Philadelphia and Reading Railroad down the Lehigh Valley ; and (3) those shipped over the main line of the Philadelphia and Reading Railroad down the Schuylkill Valley. In special localities, where a favorite coal is largely used, the consumer will speak of one class, composed of his favorite coal, which possibly comes from two or three collieries, with a total aggregate annual production of less than a million tons; and of a second class, composed of the coals from all the other collieries in the anthracite

Jan 1, 1886

By W. S. N. Waring, E. C. Bain, E. S. Davenport

The more familiar compositions of both the iron-carbon-chromium' and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallo-graphic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By C. Feng, W. E. Krul

A study was made of the development of texture and the anisotropy in plastic flow of Ti-8Al-1Mo-1V alloy. Based on Pole figure determinations, the shifting of texture induced by rolling at approximately 400°C was found to be due primarily to slip rotation for the major Portion of the material. Grain boundary shear is believed to be an important factor. The anisotropy of the textured alloy was examined in terms of the variations of yield stress under tension and the ratio of bi -axial strain increments µp, in the temperature range 25" to 290°C. The results were related to Hill&apos;s theory on plastic anisotropy. The Schmid factors of (1100)[1120], (1101)[1120/, and (1101)[1120] slip systems were analyzed and found to be compatible with the observed anisotropy. Cross-slip between these planes was proposed as a possible deformation mode. In a number of published articles, considerable interest has been directed to the possible achievement of texture hardening in hcp metals. Following Backofen, Hosford, and Burke,&apos; this phenomenon was related to the yield criteria of the material and was expressed in terms of the biaxial strain ratio, r = d?w/d?l. The higher the value of r, the greater is the expected potential for texture hardening under certain loading conditions. For a given material, r varies with direction. Such variation can be traced to the anisotropy in plastic flow and can be explained within the framework of the various modes of deformation. Hatch2 found that a high r value coincides with a texture whereby the (0001) pole is closely aligned with the surface normal for sheet materials, Based on the analysis of the slip on the {1010}, {1011}, and (0001) planes, Lee and Backofen3 and Avery, Hosford, and Backofen4 concluded that the resistance to thinning is reduced by the operation of the (0001) <1120> slip system; with this reasoning they were able to explain the low r values (i.e., r « 1) observed in magnesium alloy sheets in the rolling direction and in commercially pure titanium in the transverse direction. The general equation, dealing with plastic flow in a polycrystalline aggregate has been used to correlate the plastic anisotropy and texture. In this expression, T and s are shear and normal stresses, and dri and d? are shear and normal strain increments, respectively. Assuming that five slip systems are operative within each grain and applying the principle of maximum work,5,6 one can determine the m value among the available systems. On this basis, Hosford7 and Chin, Nesbitt, and Williams&apos; were able to correlate m with yield stress under plane-strain compression, and Svensson9 was able to predict the variation of yield stress in textured aluminum. These workers made their analyses from materials in which slip operation is known to be associated with plastic flow. Questions remain regarding the derivation of Hill&apos;s theory on plastic anisotropy,10,11 since it was formulated on von Mises&apos; yield criterion.&apos;&apos; Its ability to deal with other forms of deformation has been in doubt.13 Others have discussed the validity of Hill&apos;s quadratic equation relating strain and yield stress.14&apos;15 For hcp titanium, deformation by various modes of slip and twinning operations has been reported.16-20 If all possible modes of deformation operate and contribute substantially to the plastic flow, it is difficult to imagine how the quadratic expression can suitably describe the anisotropic plastic flow of titanium alloys. Backofen and Hosford15 considered that Hill&apos;s is a macroscopic theory and implied that the major mode of deformation by slip mechanism will adequately describe anisotropy of the material. In the present investigation, slip operation will be shown to play the major role in the development of sheet texture induced by rolling of a commercial titanium alloy. Although twinning and other modes of deformation may also operate, their operation is believed to be secondary. The anisotropic properties of the sheet, which can be expressed in terms of directional variation of r, µp = -d?w/d?l and the yield stress will be shown to be governed primarily by slip operation. MATERIALS AND EXPERIMENTAL TECHNIQUES The titanium alloy chosen for the present investigation had a nominal composition of 8 wt pct Al, 1 wt pct Mo, 1 wt pct V, and 0.1 wt pct interstitial impurities. Sheets varying between 0.1 and 0.15 in. thickness were used. The alloy was received in a condition which was prepared by rolling at 900°C and annealing at 700°C. Subsequently, the sheets were subjected to further reduction in thickness by rolling at 400°C. A total reduction in thickness of 65 to 70 pct was obtained by a series of quick passes in a rolling mill with intermediate reheating. Further reduction in thickness was not possible due to cracking developed at the edges of the sheets. X-ray measurements were conducted in a Siemens and a Norelco unit to determine the texture of the sheets. Reflection techniques were used exclusively with CuK, radiation and a nickel filter. The loss of X-ray intensity due to geometric defocusing was calibrated with a technique described previously." The (0001), (1010), and (1071) pole figures were plotted from 0 to 80 deg, and to present the texture elements quantitatively, inverse pole figures were constructed following the technique described by Jetter, McHargue, and Williams.22 Tensile experiments were carried out at 25", 175",

Jan 1, 1970

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By G. E. Archie

The usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy. Introduction The electrical log has been used extensively in a qualitative way to correlate formations penetrated by the drill in the exploitation of oil and gas reservoirs and to provide some indication of reservoir content. However, its use in a quantitative way has been limited because of various factors that tend to obscure the significance of the electrical readings obtained. Some of these factors are the borehole size, . the resistivity of the mud in the borehole, the effect of invasion of the mud filtrate into the formation, the relation of the recorded thickness of beds to electrode spacing, the heterogeneity of geologic formations, the salinity or conductivity of connate water, and, perhaps of greatest importance, the lack of data indicating the relationship of the resistivity of a formation in situ to its character and fluid content. On the Gulf Coast it is found that the effects of the size of the borehole and the mud resistivity are generally of little importance, except when dealing with high formational resistivities or extremely low mud resistivities. Fortunately, little practical significance need be attached to the exact values of the higher resistivities recorded. Low mud resistivities are not common, but when this condition is encountered it may be corrected by replacing the mud column. With the present advanced knowledge of mud control, invasion of mud filtrate into sands can be minimized, thereby increasing the dependability of the electrical log. The effect of electrode spacing on the recorded thickness of a bed is often subject to compensation or can be sufficiently accounted for to provide an acceptable approximation of the true resistivity of the formation. As development of a field or area progressively enhances the knowledge of the lithologic section, the resistivity values of the electrical log take on greater significance, ultimately affording acceptable interpretations. The salinity, and

Jan 1, 1942

By Daniel D. Pollock

The il&apos;lott and Jones theory of thermoelectricity predicts that the absolute thermoelectric power of alloys of transition and noble metals should be a maximum when the concentration of the noble metal is approximately 55 to 60 at. pct. An examination of the emf of a series of relatively pure alloys of copper and nickel shows that the predicted maximum occurs at about 57 at. pct Cu. This excellent agreement with the theory is considered to substantiate the Mott and Jones theory of thermoelectricity for binary alloys of transition elements. This theory is extended to show that the emf behavior of dilute, ternary copper-nickel base alloys, which contain approsimately 60 pct Cu and 40 pct Ni, may be described in terms of a scattering mechanism. The scattering effect of a third element is demonstrated to be a function of its valence and its period in the periodic table. Small amounts of solute elements have additive scattering effects upon the emf of the Cu-Ni base. The Mott and Jones equation is modified to include this scattering parameter. This adaptation accurately describes the thermoelectric behavior of ternary and quaternary CLL-Ni base alloys. An empirical form of the modified Mott and Jones equation is derived which permits the calculation of thermoelectric power with an average error of less than 0.4 pct at 500 "C. CONSTANTAN has long been used as a thermocouple element. Its approximate composition varies from 50 pct Cu, 50 pct Ni to 65 pct Cu, 35 pct Ni. Small amounts of manganese, iron, and other elements have been used to modify the composition in order that the resultant emf vs platinum conforms to nationally accepted table. Adjustments of this type are made on a purely empirical basis. Constantan was originally made in Germany and was imported into this country for thermoelectric and electrical resistance purposes. During World War I, the supply of this material became seriously depleted. The work of Bash4 was done in this period in order to develop a satisfactory substitute for the imported material. Bash&apos;s empirical work on Cu-Ni alloys is still the basis for all commercial constantans made in this country. No reexamination of the electrical properties of this system has been made, despite the fact that it is now well known that Bash&apos;s alloys contained impurities which strongly affected their thermoelectric behavior.

Jan 1, 1962

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.&apos; This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.&apos;" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson&apos; as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, &apos;&apos;p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler&apos;s saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By P. Barnes

It may he of interest, and perhaps of inzportance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings." Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus: 1. Provide a flat board as large as the tracing which is to be copied. 2. Lay on this hoard two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of 3/8" thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed.

Jan 1, 1879

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By H. C. George

The Wisconsin Zinc District, or the Upper Mississippi Lead and Zinc District as it is often called, lies in the southwestern corner of Wisconsin, in Grant, Iowa and Lafayette Counties, and it includes adjoining parts of Illinois and Iowa. The district is about 70 miles long, north and south, and about 40 miles wide, east and west. It lies wholly within what is geologically known as the non-glaciated area of the Upper Mississippi Valley. HISTORY OF THE DISTRICT The district was first opened up as a lead producer in 1822. From this time until 1860, about 205,000 tons of cog lead (galena) and washed lead (galena) was produced from shallow crevices and openings. From 1860 to 1900, about 74,500 tons was produced, and since that time, from 5000 to 7000 tons has been produced annually. Since 1900, most of the lead concentrate produced has been as a byproduct of the zinc mines. The first zinc ores were mined about 1862. These were the carbonate ores, locally known as "drybone." Very little zinc blende was mined in the district, previous to 1875. The zinc blende ores mined from 1875 to 1900 were mostly of the high-grade, hand-cobbed, sheet-ore class, which usually contained from 45 to 60 per cent. metallic zinc Such mines as the "Sallie Waters," "Quinlin," &apos;Lead Mine," "Benton Blende," and "Ida Blende," located near Benton, Wis., were mines which produced ores of this type, during this period. The mines located at Highland, the "Coker Mine" located at Livingston, Wis., and the "Opencut Mine" located at Shullsburg, Wis., were mines that were heavy zinc carbonate producers, previous to 1900. The production of zinc ores in the district from 1862 to 1890 was about 283,500 tons, mostly zinc carbonate, with a probable average metallic zinc content of 30 per cent. From 1890 to 1903, the production

Jan 1, 1918

By H. A. Buehler

The Ozark region occupies a large part of the southern half of Missouri, the northern portion of Arkansas and comparatively smalll areas in northeast Oklahoma, southwest Kansas, and southern Illinois. It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The Boston Mountains extending for a distance of some 200 miles (321 km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Frangois Mountains in St. Frangois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.). The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. Stratigraphy The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Frangois Mountain district. Although located geographically near the eastern edge of the Osarks, the St. Frangois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Gene-vievg County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous action, since the first sedimentary beds were deposited.

Jan 1, 1918

By S. Katz, M. E. Nicholson, J. J. Kelly, D. R. Curran

A series of wedges of 1020 steel (2 1/2 by 6 by 8 in.) were explosively loaded, as shown in Fig. 1. A slab of explosive on the surface of the steel wedge was initiated simultaneously along one edge, producing an essentially two-dimensional oblique shock in the metal. Pressure and density in the metal were measured as a function of distance from the explosive-metal interface by a method described elsewhere.&apos; While for pressures below 130 .kbars the technique produces accurate results, for greater pressures the presence of two shock waves in the metalzy3 makes interpretation of the data uncertain. However, the location of the transition in pressure at 130 kbars can be readily identified from the data. The assumption of a single shock in the region above 130 kbars overestimates the pressure computed on a multiple-shock model. After firing, the wedges were sectioned, lapped, and etched with 2 pct Nital. A photograph of an etched specimen is shown in Fig. 2. The specimens were examined metallographically. The dark region, at the top of the specimen, was heavily banded, Fig. 3, while the lighter area was comparatively free from banding, Fig. 4, the boundary between the two regions being quite abrupt. The very light regions at an angle of about 45 deg to the explosive-metal interface show virtually no banding. The origin of these light regions, which are not Luder&apos;s bands, is not yet explained. The thickness of the heavily banded area was measured and compared with the pressure at the boundary between the heavily and lightly banded regions. The results of these measurements and calculations are given in Table I. For all shots, the pressure at the boundary is approximately the same

Jan 1, 1960

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956