Search Documents

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By E. Brunner, E. S. Mardock

A method of measuring oil saturations in cores or sand packs by neutron scattering is described. This method permits local SatUrations to be measured in a core enclosed in a steel pressure vessel without interrupting the flow. calibration data and a saturation distribution measurement obtained with the apparatus are included by way of illustration. Introduction In laboratory flow experiments designed to study the mechanism of oil production it is frequently necessary to measure the oil saturation in a core or sand pack containing Oil, gas, and perhaps brine. It is sometimes desirable that the saturation measurement refer to a relatively small portion of the core, so as to eliminate end effects; that it be made without interrupting the flow, and that it be applicable to a core enclosed in a steel Pressure vessel capable Of withstanding the Pressures encountered in petroleum reservoirs. None of the usual methods of measuring saturation meets all Of these requirements. To measure the gas saturation by observing the apparent compressibility of the gaseous Phase1 would require the interruption of the flow and would give an average saturation for the whole core. An electrical conductivity method is available for measuring brine saturations,2,3 but it is not applicable to oil. A radioactive tracer might be used if a suitable substance could be found that would dissolve in the oil, emit gamma radiation, and not be adsorbed on the sand, the steel core holder, or in an aqueous- phase. The large gamma-ray background from the mass of radioactive oil in other parts of the apparatus might, however, be undesirable. There remain for the saturation measurement methods involving the absorption or scattering of some penetrating radiation produced outside the apparatus. It might be possible to use X-rays or gamma rays; but these radiations would be so much less strongly absorbed and scattered by the oil than by the steel walls of the core holder and by the sand that it seems doubtful that much precision could be attained. In a beam of neutrons, however, there is a radiation that is very penetrating and, moreover, its scattering by substances containing hydrogen, such as oil, is qualitatively different from that occasioned by other materials. It would seem possible, and has proved to be quite practicable, to measure oil saturations accurately under the required conditions by means of neutron scattering. The first, to our knowledge, to suggest neutron scattering as a means of measuring oil saturation were F. Brans and ,. A. Bottema,4 of the Amsterdam laboratories of the Bataafache Petroleum Maatschappij, who made a few preliminary experiments to test the method while they were engaged in exploring the possibilities of neutrons for well-logging purposes. A comprehensive account of neutrons and their behavior will be found, together

Jan 1, 1946

By E. S. Mardock, E. Brunner

A method of measuring oil saturations in cores or sand packs by neutron scattering is described. This method permits local SatUrations to be measured in a core enclosed in a steel pressure vessel without interrupting the flow. calibration data and a saturation distribution measurement obtained with the apparatus are included by way of illustration. Introduction In laboratory flow experiments designed to study the mechanism of oil production it is frequently necessary to measure the oil saturation in a core or sand pack containing Oil, gas, and perhaps brine. It is sometimes desirable that the saturation measurement refer to a relatively small portion of the core, so as to eliminate end effects; that it be made without interrupting the flow, and that it be applicable to a core enclosed in a steel Pressure vessel capable Of withstanding the Pressures encountered in petroleum reservoirs. None of the usual methods of measuring saturation meets all Of these requirements. To measure the gas saturation by observing the apparent compressibility of the gaseous Phase1 would require the interruption of the flow and would give an average saturation for the whole core. An electrical conductivity method is available for measuring brine saturations,2,3 but it is not applicable to oil. A radioactive tracer might be used if a suitable substance could be found that would dissolve in the oil, emit gamma radiation, and not be adsorbed on the sand, the steel core holder, or in an aqueous- phase. The large gamma-ray background from the mass of radioactive oil in other parts of the apparatus might, however, be undesirable. There remain for the saturation measurement methods involving the absorption or scattering of some penetrating radiation produced outside the apparatus. It might be possible to use X-rays or gamma rays; but these radiations would be so much less strongly absorbed and scattered by the oil than by the steel walls of the core holder and by the sand that it seems doubtful that much precision could be attained. In a beam of neutrons, however, there is a radiation that is very penetrating and, moreover, its scattering by substances containing hydrogen, such as oil, is qualitatively different from that occasioned by other materials. It would seem possible, and has proved to be quite practicable, to measure oil saturations accurately under the required conditions by means of neutron scattering. The first, to our knowledge, to suggest neutron scattering as a means of measuring oil saturation were F. Brans and ,. A. Bottema,4 of the Amsterdam laboratories of the Bataafache Petroleum Maatschappij, who made a few preliminary experiments to test the method while they were engaged in exploring the possibilities of neutrons for well-logging purposes. A comprehensive account of neutrons and their behavior will be found, together

Jan 1, 1946

By R. V. Norris

THE wage rates and working conditions in the anthracite. region of Pennsylvania have been governed for nearly 20 years by the award of the Anthracite Coal Strike Commission, appointed Oct. 16, 1902, by President Roosevelt. The report of this com-mission, made in March, 1903, was accepted and, with eight modifications made at various dates, has had .almost the force of law, and has kept this great indus-trial region free from strikes for almost a generation. In 1920, President Wilson appointed an Anthracite Coal Commission, and its report, accepted Aug. 30, 1920, governed wage conditions to April 1, 1922. Actually, the agreements have been for terms of two to four years, and lately, in 1916 and 1920, the employ-ees have continued at work pending the negotiation of new agreements which were made retroactive, and which have all been modifications of the original 1903 award. With the expiration, April 1, 1922, of the 1920 award approaching, Mr. Lewis, president, of the United Mine Workers of America, addressed a letter, on Feb. 20, to the operators, suggesting a meeting on March 15; this date was accepted by the latter, with the notation that the time was short. At the meeting, the Mine Workers presented 19 demands, and advised that if a satisfactory agreement was not reached by April 1.a suspension of mining would occur, contrary to the practice since 1916 of continuing work with a retro-active adjustment.

Jan 6, 1922

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,' who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961

By David Cole

The appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent machine, or to do more work except by the use of superimposed decks, the latter having obvious disadvantages. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2. The old system accomplished stratification satisfactorily but has

Jan 1, 1915

By Walter Crafts, D. C. Hilty

The liquidus diagram for the iron field of the Fe-S-O system has been derived experimentally. The solubility of oxygen in molten Fe-S alloys has been measured at several temperatures and found first to decrease slightly and then increase rapidly with increasing sulphur content. IT is well-known that the types, distribution, and amount of inclusions in any given steel are closely allied with the oxygen and sulphur contents of the metal, so that the term "deoxidation" as conventionally applied in steelmaking refers not only to the control of oxygen and oxide inclusions but to collateral modification of sulphide inclusions as well. Inclusions commonly occur in steel as mixtures of oxides and sulphides, sometimes closely associated and sometimes apparently completely divorced. Their effects on the properties of the metal may vary widely depending on their types and distribution as well as on their quantity. The mechanism by which inclusions form, however, and the means for controlling it are exceedingly complex and not well understood. Nevertheless, as described by Benedicts and Lofquist' and by Wentrup' all oxide and sulphide inclusions, excluding mechanically entrained matter, must result from specific modifications of the basic equilibria of the Fe-S-O system. In an investigation of the mechanism of deoxidation and inclusion formation being carried out at the Union Carbide and Carbon Research Laboratories, it became evident that quantitative data for the fundamental Fe-S-O system were essential to a better understanding of the problem. Consequently, the liquidus surface of the portion of the Fe-S-O diagram of interest in steelmaking has been determined, and the solubility of oxygen in liquid iron containing sulphur has been measured. Fe-S-O Diagram The portion of the Fe-S-O diagram of specific interest in steelmaking is the Fe-FeS-FeO corner. Of the contiguous binary diagrams for this partial system, only those for Fe-FeO and Fe-FeS are known with reasonable certainty.3 Several attempts to derive the FeO-FeS diagram have been made, chief among them being the work of Giani as reported by Oberhoffer,4 and, more recently, that of Vogel and Fulling." Although both Giani and Vogel and Fulling published diagrams for the FeO-FeS system, their observations indicated that the oxide component approximated Fe3O4 rather than FeO, so that there is doubt whether the system is truly binary. Benedicts and Lofquist and also Wentrup published qualitative sketches of the ternary diagram based on the assumption that it was of the type described by Marsh for a ternary system in which two of the contiguous binary systems are simple eutectic systems and the third exhibits a solubility gap in the liquid. Apparently, however, the only previous effort to establish the diagram experimentally was that of Vogel and Fülling whose results are reproduced in Fig. 1. Although defining approximately the limits of the miscibility gap and the location of the ternary eutectic, point E in Fig. I, Vogel and Fülling's diagram must be considered only semiquantitative. It was derived from a limited number of observations mainly along two quasi-binary sections, and the directions of the tie-lines and the location of the critical point, K in Fig. 1, were estimated by computation. Experimental Procedure The experimental technique employed for the present investigation involved melting mixtures of ferrous sulphide and ferric oxide in contact with iron. Since it was considered that in this part of the system the vapor pressures of sulphur and SO, are so low that they would not affect the results significantly, the melting was carried out in a current of argon to sweep out products of any initial re-

Jan 1, 1953

By Arthur Coffinberry

EVE have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, com-bined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was, undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atones, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such informa-tion is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,' in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young's modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By P. Hazebroek, M. Prats, E. E. Allen

Well locations in water floods frequently do not coincide with the ideal well locations associated with the flood pattern which is used. A question of importance is. "How much oil is lost because of this?". This is the problem treated in this paper. It is assumed that each pattern in a five-spot flood has the proper number of production and injection wells but that the wells may be off-pattern. The distance by which a well is off-patern is given in terms of the pattern spacing, defined as the length of one side of a five-spot. The influence of off-pattern wells on the performance of a five-spot flood has been investigated mathematically for unit mobility ratio. All production and injection rates are assumed to remain equal. The loss in recovery resulting from pattern irregularitie: has been calculated at a cumulative water injection corresponding to a 98 per cent water-cut in a regular five-spot. Displacing a single production or injection well by about one-third the pattern distance reduces the total field recovery by 4.4/N per cent of the recovery obtainable with regular spacing, where N is the number of five-spots in the flood (assumed large). When off-pattern wells are separated by at least one regular five-spot and are displaced by less than one-third the pattern distance, the total loss in recovery in a large-scale flood is, at most, 1 per cent of the recovery obtainable from that field with a regular five-spot pattern. However, much higher losses may occur if the off-pattern wells are not separated by a regular five-spot, if the rates are imbalanced, or if the mobility of the injected water is higher than that of the crude. Although the loss in oil recovery due to pattern irregularity often may be low, the off-pattern case will always require injection of more water to reach the same final water-cut. The volume of water injected per unit volume of oil displaced has been calculated for each five-spot adjacent to a five-spot containing a single 08-pattern well. The cumulative water injection at the time of 98 per cent water-cut may be increased by as much as 37 per cent when a production well is displaced one-third the pattern distance toward an injection well. The existence of differences between actual subsurface locations and the idealized well patterns used in secondary recovery operations is well recognized. However, the methods commonly used for predicting waterflood behavior ignore such differences, even when subsurface locations are known. The reason for this is simple. The idealized well patterns are highly symmetrical and, as such, the production history of the pattern (and even of the field) can be determined from that of a few production wells—usually from only one. Consideration of the many irregular well spacings found in a specific field would entail a large amount of work, and then the results would be applicable only to that specific field. In an attempt to provide an answer to the more general problem, this paper considers a water flood having an idealized well pattern, except for one well which is not at its regular location. When several off-pattern wells are present, their contributions are assumed to be additive unless the off-pattern wells are close to each other. Only four positions of the off-center well (at x, y. of Fig. 1) are considered in this paper. These are shown

By S.H. Ash, P.S. Miller

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By George B. Langford

THE McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dikes of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compressive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed-an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitit,e dikes.

Jan 1, 1938

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN : Submitted herewith are the report of the Treasurer for the year 1944 and reports for the same year of the following standing committees: Membership, Ad- missions, Papers and Publications, MIN- ING AND METALLURGY (Magazine), and Library. To these reports you are referred for additional details.

Jan 1, 1946

By Lawrence A. Shepard, Richard H. Krock

A series of ductile, two phase W-Ni-Fe composites, sintered in the presence of a liquid phase, were tested in tension. Identical room temperature stress-strain curves were obtained for specimens containing from 80 to 92 wt pct W (58 to 75 vol pct W particles). The composites exhibited a maximum elongation of 29pct at room temperature, and 10.7 pct at 77 °K. The tungsten particles in the composite elongated by the same amount at these temperatures. Single-phase alloy specimens matching the composition of the composite matrix showed about one half the flow stress of the composites. The test results demonstrated that the mechanical properties of W-Ni-Fe composites are determined by the tungsten particles alone and are independent of matrix volume fraction or mean free path over the composition range studied. A general prediction of the plastic behavior of two-phase alloys or composites from a knowledge of the properties, size, shape, and dispersion of the individual components is not, at present, possible. The excellent theoretical and experimental exposition of the dispersion-strengthening problem applies only to cases where the stronger phase is present as fine particles and in volume fractions of a few percent. Materials in which the stronger phase constitutes a significant fraction of the volume, although of broad engineering interest, have received comparatively little analytical attention. This important group of materials is the concern of the present study. The degree of deformation of each phase during the plastic working of a ductile two-phase alloy has been established by Boas and Honeycombe,1 Clare-brough,2 and Clarebrough and berger.3 These workers empirically correlated the recrystallization temperature of the individual phases with the degree of cold work sustained by each. It was shown that the deformations of both phases are equal and therefore the same as that sustained by the composite whole when the volume fraction of the stronger phase exceeds 35 pct. At yielding, however, deformation begins in the weaker phase. A direct correlation of composite strength, as a function of deformation, with the strength of the individual components cannot be made. In the presence of stronger phase particles, the flow stress of the weaker matrix phase is enhanced by an additional hydrostatic component. The development and potential magnitude of matrix strength promotion upon straining has not even been experimentally established. Quantitative work in this field has been confined to ceramic-metal composites. These materials fracture at strains considerably below 1 pct by cracking of the ceramic particles.4-6 An indication of the potential constrained matrix strength capacity is given by the observation by Nishimatsu and Gur-land4 that the maximum tensile strength of a WC-Co composite is almost double the bulk strength of the cobalt matrix. The relationship between composite strength and geometry is ordinarily expressed in terms of the mean-free matrix path (referred to subsequently as MFP) between the stronger particles.* This factor takes into account both the volume fraction of matrix phase and the average size of the particles. unke17 concluded that composite strength varied directly with the decreasing log MFP, following the Gen-samer8 relationship. However, Gurland and ~radzil~ reported a strength maximum at an MFP of the order of 1 p in WC-Co composites. A ductile two phase metallic composite was chosen for the present investigation of composite mechanical properties with the view of avoiding the difficulties and ambiguities noted above. The W-Ni-Fe heavy alloy of Green, Jones, and pitkin9 contains 80 to 94 wt pct W, and nickel and iron in a weight ratio

Jan 1, 1963

By R. J. Wagner, Jim Douglas Jr., P. M. Blair

The calculation of the behavior of an oil reservoir during a water flood has long been an important problem to reservoir engineers. Buckley and Leverett derived the differential equation which describes the displacement of oil from a linear porous medium by an immiscible fluid, but this equation could not be solved by the methods of classic mathematics. Consequently, in order to integrate the equation over the length of the reservoir, they neglected the effects of capillary pressure. In the present paper, a numerical method has been developed for determining the behavior of a linear wafer flood with the inclusion of capillary pressure. The differential equation which was derived for the case of incompressible fluids is second order and non-linear. This differential equation was approximated by an implicit form of difference equation which is second order correct in both time and distance. An electronic digital computer was used to perform the numerical solution of the difference equation. INTRODUCTION The problem of calculating the flow and distribution of fluids in an oil reservoir subjected to a water flood has long challenged the reservoir engineer. The ability to solve this problem would provide a valuable tool for the design and study of field waterflooding programs. One of the first contributions in this field was made by Buckley and Leverett,'.' who developed a method of calculating waterflood performance in a linear reservoir. Their technique was limited by the practical necessity of excluding quantitative consideration of capillary pressure. It is the purpose of this paper to describe a method for calculating the behavior of a linear water flood with capillary pressure considered. This method, although limited to the linear case, should serve as a step toward the solution of the two- or three-dimensional waterflooding problem which would better describe actual reservoirs. The treatment of the problem has assumed that the reservoir is linear and homogeneous, that both oil and water -are incompressible, and that gravitational forces may be neglected, and that water is injected into one end of the reservoir and oil and water are produced from the other. Though these assumptions may not be directly applied to natural reservoirs, they are closely approached in many laboratory core tests. The physical problem has been represented mathematically by means of a differential equation and suitable boundary conditions. The inclusion of capillary pressure effects causes the differential equation to be second order and non-linear, and it is not amenable to solution in terms of known functions. Nevertheless, the problem may be solved by numerical methods. The authors have successfully calculated several cases from the start of water injection through to depletion of the hypothetical reservoir using realistic capillary pressure and relative permeability characteristics that were chosen so as to put the method to a test. DIFFERENTIAL EQUATION In two- or three-dimensional problems involving the two-phase flow of incompressible fluids through a porous medium, the equations describing the flow can be combined until only two dependent variables remain, the pressure in one phase, and the saturation of one phase. These variables appear in two simultaneous partial differential equations which are derived on the basis of the conservation of mass and Darcy's law as applied to two-phase flow. For a linear reservoir, this system of differential equations can be reduced to a single, nonlinear, second order, parabolic differential equation for one dependent variable, the saturation of one phase. For incompressible water and oil, it can be shown that the conservation of mass for the two phases requires that Where q, and q, are the water end oil flow rates per unit cross-section, s, and so their saturations, +, the porosity, and [ and T, dimensional space and time variables. Darcy's law, as extended to two-phase flow including the effect of capillary pressure,' is as follows:

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939