Search Documents

Jan 1, 1968

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By J. A. Richardson

J. A. RICHARDSON[t]-Mr. Stuckey's account of the geology of the kaolins of North Carolina suggests that they exhibit some features similar to those of the Malay Peninsula. About one half of British Malaya (some 26,000 square miles) is occupied at the surface by igneous rocks, of which granite and its associated derivatives constitute fully 90 pct. The average granite is a biotic variety. It is predominantly potassic but carries, in addition, notable amounts of soda and lime so that albite and albiteoligoclase are generally common constituents of the rock. The minor derivatives from granite "magma" likewise include potassic and sodi-potassic members. Decomposition of the granitic rocks has led to the formation of kaolin in many localities, but, in general, the deposits are rather small and, at present, none is exploited commercially. True primary or residual kaolins (as defined by Stuckey; p. 48 Vol. 173, p. 2 TP 2219) have been developed from feldspar veins, pegmatites and from other granitic differentiates which cut through the larger masses of granite; they are usually small and narrow. Kaolin has been derived from aplite, quartz porphyry, quartz micro-porphyry, felsites and microgranites belonging to a complex known as the Chegar Perah-Pulai intrusion in northwest Pahang and southwest Kelantan. The bulk of the component rocks has been more or less strongly sheared. Kaolin-like end products have been formed from both sheared and nonsheared varieties. Kaolin has been formed also by the complete breakdown of trondjemite flanking the northwestern and western margins of the complex Bukit Ranjut syenite intrusion in northwest Pahang. These trondjemites range in composition from essentially quartz-free albiteplagioclasites to quartz-free microcline rocks; they are, in effect, the syenitic homologues of white sodic and potassic granite-aplites. The granites in Malaya have generally undergone more or less severe surficial weathering leading to the production of a spongy and rather cellular or a soft "mealy" material (sandy clay) down to depths of about 100 ft; in places the granite is strongly decomposed down to 150 ft. There has occurred, therefore, widespread partial kaolinization, but, in general, no extensive deposits of good quality kaolin seem to have been formed by these processes of decay. Frequently, the katamorphic processes of desilicification have advanced beyond the production of kaolin towards the formation of lateritic end products. The more important Malayan kaoiins seem to be confined to the western alluvial plains, particularly in areas either where granite crops out at surface, or where it forms the bedrock of the alluvium. There are numerous excellent examples around Gopeng and elsewhere in the Kinta Valley of Perak. Such kaolins belong to Stuckey's groups of secondary deposits, and, like them, these also may be bedded. Field observations have established the existence of what for want of a better name is referred to by the Malayan Geological Survey as "granite wash." It is believed that granite, undergoing extensive deeply penetrative and probably rather rapid destruction under humid tropical weathering (temperature around 90°F; rainfall about 100 in. per annum; high humidity) "flowed," was moved by "creep" and, in addition, probably slumped in large waterlogged masses of sandy clay from topographic salients onto the adjacent flats. Either during this period of transmigration or later when the sludged granite detritus, after having more or less come to rest, was attacked by flowing water, differential sorting and erosion took place with the result that the resorted debris was moved and later deposited as bedded alluvium. In this way, banded "granite wash" was produced comprising alternating bands of clayey sand (resorted granite sludge) and white

Jan 1, 1947

By Oliver Bowles

WHEN a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibili-ties of much wider application. A wire saw consists of a 3/16-in. or 1/4-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1.) The teeth of the saw are sand grains carried in the grooves between the strands.

Jan 1, 1936

By A. M. Nicholas

WHEN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it ,was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keel) the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft.-(5.5 in.) up in the total lift of 34 ft. The idler pulley was set eccentric by 3/4 in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets clumped satisfactorily.

Jan 2, 1918

By Jerry B. Newby

The outstanding features in Pennsylvania and New York during the past year were the buying of acreage for water-flooding in other Pennsylyania fields than the Bradford and Allegany districts, the wide adoption and use of the five-spot plan of development and water-flooding in the Bradford and Allegany districts, the discovery of gas production in the Onondaga lime in southwestern New York and the opening of the T. W. Phillips Gas & Oil Co. Fifth Sand pool in Butler County, Pennsylvania. Water-flooding has occurred in many other fields than the Bradford, Pa., and Allegany, N. Y., fields. In some the flood was a natural encroachment of edge water, in others the water was introduced into the productive sand through wells either accidentally or intentionally. Most of these floods have not been commercially successful. There has been some interest aroused in the Clarendon field, Warren County, Pennsylvania, by a new and apparently successful flood and other floods have been begun. Five-spotting in the Bradford and Allegany fields is the plan of water-flood development under which the area to be drilled is laid off in a grid of equal-sized squares with water intakes located at each corner of the squares and oil wells located in the centers of the squares. So far there are two five-spot water floods that are, beyond doubt,, commercial successes. There were 600 acres under five-spot flooding at the end of 1928, as against 150 at the end of 1927. By the end of 1929 there will be a total of between 1200 and 1500 acres five-spotted unless a low market for Pennsylvania grade crude oil develops. An increase of 6000 bbl. in average daily production is expected to accompany this development in 1929. The Belmont-Quadrangle Drilling Corpn. found the Onondaga lime or a higher strata at 3995 ft. north of Bolivar, Cattaraugus Country, N. Y., and a number of miles from any other important gas production. When drilled to 4006 ft. the well yielded 3,500,000 cu. ft. of gas and when shut in 1700 Ib. rock pressure. The one oil pool opened in 1928 was in Buffalo township, Butler County, Pa., in October, when the T. W. Phillips Gas & Oil Co. completed a wildcat well in the Fifth sand at 700 bbl. a day, which by the end of

Jan 1, 1929

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By J. S. Crump, H. L. Stone

Laboratory studies have indicated that displacement of oil from a reservoir by means of a condensing gas drive results in extremely high oil recovery, approaching 100 per cent under the most favorable circumstances. A condensing gas drive is defined as a gas drive in which the gas utilized is appreciably soluble in the oil it is displacing. The laboratory studies consisted of a number of gas drive displacement experiments, all using a horizontal, sand-packed, steel tube as the laboratory reservoir. The experimental results indicate that the more soluble a gas is in the oil to he displaced, the more efficient that gar is as a displacing fluid. Experiments were conducted utilizing both a light, volatile crude and a heavy, asphalt crude as the in-place oil. In both cases, oil recovery was appreciably enhanced by solubility of the displacing gas. It is believed that the use of condensing gas drives would result in increased oil recovery from many reservoirs during either primary or secondary phases of production. INTRODUCTION Since the early days of the oil industry there has been an increasing awareness of the problems of oil recovery. During the last few decades particularly a growing recognition of the problems has led to widespread attempts on the part of the industry to increase oil recovery by improved technology. One method which has been used to increase recovery is the maintenance of reservoir pressure by injection of gas. Part of the beneficial effect resulting from this gas injection was to prevent evolution of the gas dissolved in the reservoir oil, since such evolution would cause the oil to shrink and become more viscous, thereby adversely affecting oil recovery. In most instances, the gas injected was predomillantly methane, and so the possibility of oil recovery by retrograde vaporization existed. Laboratory investigations of displacement of reservoir oils by methane, carried out at high pressure, have indicated that considerable additional recovery of light oils could be effected by vaporization, but only at the cost of a severe volumetric shrinkage of the residual oil which would cause a decrease in relative permeability to oil in the reservoir. Consequently, recovery of oil by physical displacement would be impaired. The study suggested, therefore, that recovery of oil might be enhanced by injecting into the reservoir a gas known to be appreciably soluble in the oil at reservoir conditions. Swelling of the oil due to solution of gas should result and yield a consequent increase in the relative permeability to oil. The work described in the following sections was, therefore, undertaken to investigate the possibility of increased recovery by this mechanism. Research similar to that reported in this paper has been conducted by The Atlantic Refining Co.1,2,3 In these studies, Whorton, et al, and Slobod, et al, used methane-rich gas to displace oil from model reservoirs. Solubility of the gas was achieved by keeping the reservoir pressure greater than the saturation pressure of the original oil, and the degree of this solubility was varied by operating at different reservoir pressures. Thus the Atlantic project was primarily a study of the effect of reservoir pressure upon oil recovery by gas drive. The objective of the work reported in this paper was to study the effect of gas composition upon oil recovery while holding the reservoir pressure constant. DESCRIPTION OF EXPERIMENTS The discussion of the preceding section suggests that

Jan 1, 1957

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done ? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on t,his subject, and the results seem to furniih an answer to the question propounded above. Sampling for the U. 8. Geological Survey Coal- Testing Plant. In organizing the work of the testing-plant, it was decided that coal, in car-load lots only, would be accepted for testing; also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sample from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory established in connection with the plant and operated under the direction of Prof. N W. Lord of the Ohio State University, Columbus, Ohio. Mine-Samp1ing.—Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations adopted for mine-sampling mas, that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine.

Jan 1, 1906

By C. Z. Serpan, L. J. Wittenberg

The density of liquid plutonium was determined, by a pycnometm'c technique, from 664 to 788°C and exhibited a temperature dependence, which could be expressed as:. P= C17.63 - 1.52 x 10-"t] +0.04 g per cc where t = OC. These density values compare favorably with the values previously obtained by a technique utilizing Archimedes' principle. The apparatus and method were evaluated when the densities 0.f molten tin and bismuth were measured and found to be in agreement with accepted literature values. PLUTONIUM or an alloy of plutonium in the liquid state has been proposed as a fuel for a fast-breeder type nuclear power plant.' Since knowledge of the liquid density of plutonium is required for the proper design of such a system, this study was undertaken. In addition, the density and volume expansion coefficient of liquid plutonium are of interest for comparison with these same properties of the six allotropic modifications of the solid metal. Comstock and GibneyZ were first to report a value for the density of liquid plutonium. The value for only one temperature, 665"C, was calculated from data obtained by the radiography of the meniscus, Fig. 3. Recently, the density at a series of temperatures has been reported by Knight,3 who obtained his values by using a differential volumeter, and by 01-sen, Sandenaw, and Herrik, who obtained their values from measurements of the loss in weight of a tungsten bob immersed in the liquid. The density of liquid plutonium reported here was determined by a vacuum pycnometer method. In an evacuated system, the tips of calibrated tantalum pycnometers were lowered beneath the liquid sur-

Jan 1, 1962

By R. B. Fuller

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries.

Jan 8, 1951

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By R. N. Lambert

This chapter discusses the evolution of high-speed shaft sinking in the South African goldfields. Whether we are talking of an additional shaft at an existing mine or the opening of a new mine, the increasing depth of the ore-bearing reef and the unremitting inflation of costs have provided the compelling incentive to shorten the time taken to sink a shaft and start earning revenue. The high costs of sinking a modern shaft system in South Africa are indicated by the recent example of a deep-level mine in the Orange Free State where the cost was nearly $22!42 million. This was for a single large shaft of 33 ft 6 in. diam (in all cases, shaft diameters refer to the finished diameter of the shaft, e.g., inside the concrete) and 7600 ft deep with a prestressed concrete brattice wall dividing the shaft into upcast and downcast compartments. Higher costs and the consequent demand for increased tonnages, deeper shafts with higher rock temperatures, which necessitate highly sophisticaled ventilation and refrigeration requirements, have all accentuated the importance of time in a shaft-sinking operation. Rectangular shafts with their simple design and comparatively reasonable sinking speeds remained popular for many years until greater mining depths combined with a host of the other allied problems inevitably led to changes in shaft design. Circular shafts appeared to offer many advantages, particularly when considering ventilation, strength, mechanization, and sinking through bad ground and heavily watered zones. However, these advantages were largely offset by the slow rate of advance necessitated by the need to stop sinking in order to line the shaft. The development of the curb ring which enabled lining to take place above the bottom of the shaft and the use of multideck stages allowing sinking and lining to be carried out concurrently resulted in a major break- through. Rectangular shafts, which are still popular elsewhere, have been superseded in South Africa by circular shafts which are almost without exception the only shafts sunk in our goldfields today.

Jan 1, 1970

By T. E. Kihlgren, N. B. Pilling, E. M. Wise

Systematic data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. Introduction The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and sometimes tin, lead and other metals. This type of alloy was generally known as 'German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates applied to a nickel silver base behave more satisfactorily than those applied to the softer and less resistant alloys, and owing to the white color of the underlying metal the article will retain a pleasing appearance despite local failures of the plating.

Jan 1, 1935

By E. M. Wise, T. E. Kihlgren, N. B. Pilling

Systematic data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. Introduction The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and sometimes tin, lead and other metals. This type of alloy was generally known as 'German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates applied to a nickel silver base behave more satisfactorily than those applied to the softer and less resistant alloys, and owing to the white color of the underlying metal the article will retain a pleasing appearance despite local failures of the plating.

Jan 1, 1935

By Takao Kobayashi

Micro-crack formation zones developed near a crack tip in rocks and ceramics play a significant role in fracture behavior of these materials. In order to study micro- crack formation near a crack tip and its effects on crack behavior, a mica-epoxy composite material was developed. Multi-layer mica flakes were embedded in an epoxy matrix. Under high stress in the vicinity of a crack tip the mica delaminated, simulating the micro-cracking along grain boundaries or crystal planes in rocks and ceramics. A compact tension specimen was fabricated from mica-epoxy composite material. During the test the load and crack opening displacement were measured following the ASTM E561 (R-curve determination) procedure. Through the compliance calibration method the effective crack length and the KR were computed. The experiment clearly demonstrates the formation of micro-cracks and their effects on the overall behavior of the specimen. The paper discusses the significance of micro-crack formation on fracture toughness characterizations, and the advantages of the use of mica-epoxy composite for detailed studies of interaction between the micro-crack formation zone and the specimen geometry and size.

Jan 1, 1982