Search Documents

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

Secretary's NOTE—on page 176,of this paper, in the fourth line of the first footnote, " 4° " should, be " 1" )'; and on page 180, at the beginning of line 23, ('lined boot" should be " unlined boot." Discussion. Frank Owen, London, Eng. (communication to the Secretary) : In his very interesting and valuable paper, Prof. Snow

Jan 1, 1900

By S. A. Lever, R. Hultgren

(E. R. Jette and J. R. Long presiding) M. B. BEVER*—The method re- ported in this interesting paper promises to he of fairly wide applicability. It may be expected that the solidus and liquidus lines in other low-melting alloy systems can also be determined by resistance measurements. As these alloys are especi- ally slow to reach equilibrium, a static method will improve the accuracy with which these parts of their phase diagrams can be determined. It should be noted that the sensitivity of the method for the determination of

Jan 1, 1950

By James W. Dally, William L. Fourney, Anders Ladegaard Peterson

For the past 3 years, the authors have been conducting research sponsored by the National Science Foundation (RANN) to improve the process of excavation by drilling and blasting. The approach followed has been experimental where the development of stress waves and fractures initiated at the bore hole have been investigated in order to obtain a complete understanding of the dynamic Fracture process. The second step in the approach has been to introduce modifications in the drill and blast procedure which will permit closer control of the fracture process.

Jan 2, 1978

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation's C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation's C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940

By C. A. O’Connell

Surface exploration drilling at Mufulira started in 1928, with drillhole No. 1 intersecting ore near the eastern fringe of the deposit. Subsequent drilling along strike intersected ore until the western fringe was fixed some 7500 ft west of drillhole No. 1. Further intensive drilling down dip disclosed a large triangle of ore with its apex 3350 ft deep. It contained approximately 11 6 million tons of ore at 4.41% total copper in three superimposed orebodies. The east and west limits of the orebodies were presumed to have a pronounced rake to the north with a strike length of 8000 ft. Subsequent exploration underground seemed to bear out this presumption to the 1150 ft level. In 1947, attention was directed to the area west of the known orebodies in conjunction with plans for increased production and increased depth of the mine workings.

Jan 12, 1962

By W. H. Adams

Among the engineering plants with new features and deserving details which are constantly being brought to the working stage in the Southern States by the generous expenditure of capital, none can exceed in interest, whether to the public or the profession, the incline-railway built from base to summit of Lookout Mountain, near Chattanooga, Tennessee. Much geological and historical interest centers in this section of the middle mountain-country. Of its geology, the Transactions of the Institute contain many particulars. Of its history, the most

Jan 1, 1888

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By Victor Rudenno

Feasibility studies for mining projects traditionally involve in their final stages a lengthy process of repetitive trial and error discounting, in calculating the discounted cash flow rate of return resulting from the respective yearly after-tax cash flows. Also, probability analysis and sensitivity analysis (in particular) require extensive additional calculations with each change of any project parameter . These inefficient repetitive procedures have two unacceptable results: 1. they are not flexible enough to allow ready analysis of dependent parameters , and 2. they require resort to high-capacity centralised computing facilities with their inherent impersonality, rather than a convenient and available desk calculator - a factor of particular importance to top mining management. Such problems can be overcome if the mining project can be represented by a reasonable straightforward mathematical economic model. The most flexible and appropriate model has been found to be one in which a maximum and minimum value for each of n parameters are supplied to a program which determines a large number of systematic combinations of parameter events and then statistically analyses them to determine the resulting coefficients of the model. In this paper the authors discuss the selection of the most appropriate type of model and outline the steps followed in its development and application.

Jan 1, 1977

By J. S. Mitchell

Cobalt recovery from arsenical concentrates by pressure leaching and reduction involves special methods and operating problems. Principal steps in the process are auto-oxidation acid leaching under pressure, filtration of the tailings, purification of the solution, hydrogen reduction of the ammoniacal solution, and electrical furnacing for sulfur removal and granulating the metal. Extracting cobalt metal from arsenical ores has presented a major metallurgical problem for many years. In acquiring the Blackbird mine near Salmon City, Idaho in 1943 Calera Mining Co. accepted the challenge to solve this problem.

Nov 1, 1956

By Frank E. Briber

In the years ahead, the industrial minerals producer will face several major challenges. Not only will he have to market increasing quantities of his product economically, but he will have to do so from lower grade deposits that are farther away from the marketplace. At the same time, he will have to comply with more regulations controlling the handling and disposal of waste products and get along with relatively less available labor than he has at present. Accordingly, industrial minerals developments of the next 30 years will be directed primarily toward helping the producer meet these challenges. There will be greater raw materials usage, new processes, new marketing practices affecting plant location, size and complexity, and maximum automation-all aimed at producing more materials at lower cost. Processes To Make the Most of Materials In future processes for industrial minerals, there will be great emphasis on more or total use of the initial raw materials or plant feed stock. This approach will result in the application of more and more concentration methods to the treatment of industrial minerals-both conventional processes and new ones that might be developed in conjunction with pyro-processing. High-intensity and electrostatic separation are certainly two areas which will see greater use in the field.

Jan 6, 1969

By Richard V. Wyman

Leaching of a granitic rock mass by slightly acid groundwater brings uranium and genetically related ions into solution in groundwater. Uranium and related ions are moved through the vadose zone by groundwater which in turn moves through zones of greatest transmissivity into a deep zone of increased hydrostatic pressure. Cyclic wetting causes the hydrostatic condition to fluctuate causing recycling described by Gruner (op cit). Multiple cycling flushes the uranium ions from rock being leached and moves it via this method to permeable beds-channels-in the deep zone.

Jan 1, 1970

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By James E. Little

Of the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of stantlard-gauge railroad and two large double-track inelines, the installation of milling-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1900.

Jan 1, 1912

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949

By F. H. Kihlstedt

The Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 60 per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1949