Search Documents

By W. C. Winegard, C. J. Simpson, C. J. Beingessner

VARIOUS organic compounds, such as borneol, carbon tetr a bromide, and hexachloroethane, solidify as transparent plastics with a fcc structure. Each of these substances undergoes a solid-state transformation from the plastic phase to a brittle phase at temperatures slightly above 20°C. Since it was known that these plastic crystals solidified like metals,1 it was decided to investigate the possibility that solid-state grain growth would occur in the same way as it does in metals. Two-dimensional grain growth in thin films of plastic organic compounds has been studied with the aid of cinemicrophotography. Samples varying in thickness between 250 and 1000 @ were prepared by subliming a thin layer of the compound onto a microscope slide plate which was then covered with a second slide plate.

Jan 1, 1968

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

CERTAIN titanium alloys when quenched to retain the 0 phase at room temperature show extensive transformation of 0 to martensitic a during deformation. Alloys of this type are usually characterized by low tensile yield strength, a large spread between yield strength and ultimate strength, and high uniform elongation. A previous investigation of this phenomenon concluded that the principal contribution of the martensitic transformation was to increase the amount of deformation prior to fail-

Jan 1, 1964

By Y. S. Bonillas

Page I. Introduction.......................... 286 II. Physiography.......................... 286 : 111. Introductory Geology...................... 287 IV. Rocks of the District ...................... 288 (A) Sedimentary Rocks..................... 288 Pinal Schist ........................ 288 Bolsa Quarteite....................... 289 Abrigo Limestone...................... 290 Capping Quartzite..................... 291 Martin Limestone...................... 292 Escabrosa Limestone .................... 295 Naco Limestone....................... 296 Cretaceous Deposits..................... 296 Glance Conglomerate................... 296 Morita. Mural and Cintura Formations........... 297 (B) Igneous Rocks........................297. Pre-Cambrian Granite.................. 297 Pre-Cretaceous Granite Porphyry............. 298 Rhyolite........................301 Other Dikc Rocks.................... 301 V. Structural Geology........................ 304 General Structure of Mule Mountains............. 304 Fault Blocks and Other Divisions............. 304 Igneous Rocks...................... 312 Copper Queen Block..................... 313 Fault Blocks...................... 313 Intrusions....................... 315 Don Luis Block....................... 315 Intrusions and Orebodies................. 316 VI. Geologic History......................... 316 VII. Metamorphism and Mineralization................. 318 General Metamorphism.................... 318

Jan 1, 1917

By O. N. Carlson, E. D. Gibson, D. W. Bare

SEVERAL investigators have recently contributed to a clarification of the controversy concerning the allotropy of chromium. Ross and Hume-Rothery1 and Vasyutinskii et a1.2 have reported high-temperature X-ray data on unalloyed chromium from which they have concluded that no allotropic transformation occurs in this metal. Bechtoldt and vacher3 in their investigation of the Cr-Ni alloy system found no evidence for a transformation in chromium and Smart and Haynes4 in critically analyzing the data presented to date concerning this system could find no evidence for a eutectoid reaction in this system. Wyder and Hoch5 in research concurrent with our

Jan 1, 1964

By C. H. Ault, D. D. Carr

Four counties in Indiana- LaPorte, Vigo, Vanderburgh, and Switzerland-have potential for deep underground limestone mining because they are in or near high population areas and have no surface-mineable limestone deposits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Mineable seams suitable for aggregate are 120-150 m (400-500 ft) below the surface in LaPorte and Vigo Counties, about 90 m (300 ft) below the surface in Switzerland County, and about 600 m (2,000 ft) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1983

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

At the meeting of the Board of Directors the following resolution was passed: "The members of the Board of Directors of the American Institute of Mining Engineers desire: to place on record their appreciation of the very great generosity of one of their colleagues and a member of the Board, George D. Barron, expressed in his gift of $5000 to relieve the financial stringency caused by the unusual expenditures of the Institute for war work and the remission of dues of those members on active service." By-Law VIII. was amended to make a slight change in District No. 5. The report of the Auditing Committee was accepted. Tellers were appointed to: count the ballots on officers and on the proposed amendment. The proposed budget for the year 1919 was presented. The following resolution re Secretary Emeritus Rossiter W. Raymond, which had been prepared, by request, by Dr. A. R. Ledoux was then unanimously adopted. "The Board of Directors of the American Institute of Mining Engineers would place upon its minutes its profound sense of loss and sorrow in the death of Rossiter Worthington Raymond, Ph. D., LL. D., Secretary Emeritus of the Institute. Both as one of its founders and as its Sec-retary for 27 years, his was the guiding spirit of the Institute for more than a generation. "During the greater part of this long period, it might almost have been said that the Institute was Dr. Raymond-and Dr. Raymond the Institute. When with the progress of growth and development, great changes were introduced, Dr. Raymond acquiesced in these in spite of some misgivings, such as those with which a father might contemplate the emergence of his child from the careful supervision of the home; but as Secretary Emeritus for the past eight years, lie was always ready with valuable advice and helpful suggestion.

Jan 3, 1919

By L. M. Cathles, L. E. Murr

Results of two years of leaching of 160 metric tons of low grade industrial copper sulfide waste in a large (40` high 10` diameter) thermally insulated tank at the New Mexico Institute of Mining and Technology are analyzed in the light of a previously developed model of the waste leaching process. It is shown that the model is verified in all major aspects and that the parameters in the model that characterize the leaching of a particular sulfide waste are usefully constrained by the results of the tank leaching experiment. The similarity between waste leaching parameters determined from the tank experiment and from interpretation of the leach behavior of test dumps constructed of similar waste encourages optimism it may be possible to predict the leach behavior of field dumps from suitably interpreted column experiments using the computer model developed.

Jan 1, 1980

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.' 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

By William C. Grady

Microscopic pyrites are present in all West Virginia coals. Sizes of these pyrites range from 0.1 µ 500 µ (1/2 mm) , and four types are noted: massive, patches, framboids, and isolated crystals. The relative and absolute abundances of the four types vary from seam to seam, and these distributions have a marked effect on the ease with which a seam may be cleaned of pyritic sulfur.

Jan 1, 1978

By L. Delatour, K. Voltaire

This paper presents various aspects of the legal and economic settings that govern the exploration for mineral resources in Haiti.

Jan 1, 1980

The Secretary : The work of Mr. A. E. Outerbridge, Jr., of Philadelphia, first made known in his paper on " The Mobility of Molecules of Cast-Iron," read at the Pittsburgh Meeting of the Institute, in February, 1896, has been reviewed by the Committee on Science and the Arts of the Franklin Institute, whose report, dated May 5, 1897, is accompanied with a table of tests made by the Committee, and amply confirming the statements of Mr. Outerbridge. Concerning the originality and novelty of his investigation, the Committee says: " The fact that a certain molecular change takes place in cast-iron in the course of time has been known and recognized by many persons for a long time, and that this change tends to relieve the internal strains and render the casting tougher has often been noticed and acted on, although in a very crude way; but, so far as the sub-committee has been able to learn, Mr. Outerbridge has been the first to make a careful study of this, and to note that the change may be hastened by impact, and the whole effect produced in a short time, and also to make a scientific study of the phenomenon. We believe great credit is due him for the initial observation and the careful work dependent thereon. The results were first given to the public in a paper read before the American Institute of Mining Engineers, on February 20, 1896. This aroused a wide-spread interest and discussion among users of cast-iron, and so far as the sub-committee has been able to determine, it has not been shown that anyone, either in this country or abroad, has antedated Mr. Outerbridge in his work in this line. The Franklin Institute therefore recommends the award to him of the John Scott Legacy Premium and Medal." This report has not been published, hut I have had the opportunity to read it in manuscript. The table of testa accompanying it comprises 91 tests of " rumbled" and an equal number of " not rumbled" companion-bars of cast-iron, 26 by 2 by

Jan 1, 1898

By Freeman Bishop

The first session of the 91st term of Congress became so completely snarled up in economics and politics that no one knows how things will go in 1970 including the White House. Everything from mineral depletion allowances to tax deferments kept the Republican President and the Democratic Congress from settling their differences. But as these reconcilements approach definition, a new battleground develops around the President's authority to make trade and tariff adjustments.

Jan 1, 1970

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953

By W. C. Ellis

Growth directions of tin, zinc, and cadmiun whisker crystals grown spontaneously fi-om the solid are summarized. In tin the edge and diagonal directions of the unit cell are jound with the exception oj- the [110] diagonal. In cadmiurn and zinc the usual dip-ections are a or a + c. The c direction has not been ohserwed. The gvouth directions from the solid are for the most part the same as those found for vapor-grozun crystals and are the ohserz:ed glide directions in plastic j-lou. Whisker crystals of these elements grown from the solid are not twinned. Specular lateral reflections are associated with planes of snall crystallographic indices. WHISKER crystals of tin, zinc, or cadmium grow spontaneously at room temperature in periods from months to years from thin electroplates and other prepared films of the respective metals.''2 It has been established that these crystals are single, but the question of twinning, such as occurs in whisker crystals of silicon,3'4 has not been resolved. Studies of morphology have been restricted to determinations of growth directions.5-' Whisker crystals are both straight and kinked. A few studies have been made on kinked whiskers including measurements of kink anglesa and determinations of growth directions,' but unfortunately not both on the same crystals. The kink angles, for the most part, for each species are grouped closely about a few unique values, but these values are not always those between observed growth directions in a single crystal. To supplement existing data, the growth directions, identification of lateral features, and presence or absence of twinning were determined with a Weissenberg goniometer by a method described elsewhereg on eight whisker crystals of tin, five of zinc, and five of cadmium. One kinked cadmium whisker was examined in detail. The specimens were needlelike, a few microns in cross section, and of the order of a millimeter in length. They were removed from electroplated substrates on laboratory specimens and commercial equipment after several years of growth as described in Table I. Since the specimens were less than 10 p in cross section they were ideally strong with no attendant risk of plastic deformation or damage in handling. Only deformation twinning has been reported for these elements. Therefore, twinning probably should not be expected in whisker crystals of these metals, particularly a twin plane containing the growth direction. A twin plane oriented in this direction was the one sought in this study. No examination was made for twinning at the boundary between kink segments except for one cadmium crystal. Well-defined reflections occur as a whisker crystal of tin, zinc, or cadmium is rotated about its growth direction when illuminated by a beam of light Although these reflections had been noted in earlier investigations, no study of them was made, probably because the earlier studies had disclosed also that

Jan 1, 1967

By Richard Moldenke

A. E. OUTERBRIDGE, JR., Philadelphia, Pa. (written discussion).¬ The fact that iron castings improve with age has long been known. Many years ago the late Sir Frederick Bramwell, a distinguished engineer, formerly in charge of the metallurgical and gun-making department of the Woolwich Arsenal, England, determined to break up a large number of cast-iron mortars of an obsolete type that had been in stock for years. It was then reported to biro that it was found to be much more difficult to break these old gun castings under the "drop" than it was to break similar gun-castings recently made, under his own supervision; he changed the.. composition of the iron and still found that whenever castings made recently were broken up (on account perhaps of superficial defects) great disparity was observed in apparent strength between the old and new castings. Sir Frederick then made many other comparative tests, such

Jan 4, 1917

By Milton H. Ward

This paper contains a review and discussion of the major design parameters of a block caving mine, with special attention given to access, development, and operational methods. Information will be provided on the economics and costs of various design alternatives, and how they can influence financial results of a particular project. Technical and economic factors that pertain to an actual operation, Freeport Indonesia, Incorporated's block caving mine in Indonesia, will be provided, and highlights of the planning, development and operation of this mine will be presented. The major thrust of the paper will be to emphasize the importance of good planning and to encourage economic analysis of various methods of layout and design.

Jan 1, 1981

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By J. P. Hammond, C. J. McHargue, S. E. Adair

Cold-rolled sheet textures have been determined for binary solid solutions of aluminum, columbium, tantalum, and zirconium in titanium. An alloy containing 3.8 pct Al had a (0002) [10101 texture, whereas alloys with the other elements had rotated (0002) [10101 textures similar to that of iodide titanium. THERE have been relatively few studies of the effect of alloying on deformation textures. A second element may be present in the base metal in solid solution and/or as a second phase. The literature offers no satisfactory explanation for the effects of solid solution alloying on textures noted thus far. For example, there is no satisfactory explanation of the difference in the textures of copper and a brass. The most complete study of the effects of solid solution alloying on deformation textures has been that of Brick, Martin, and Angier.¹ These investigators reported that the copper texture was retained by alloys of copper with up to 30 pct Ni, less than 5 pct Zn, less than 2 pct A1 or Co up to the limit of solubility. Copper containing more than 5 pct Zn, more than 2 pct Al, or the maximum soluble concentration of tin, silicon, or manganese showed the deformation texture of a brass. Bakarian² reported that additions of 0.20 pct Ca to 99.98 pct Mg or 2.0 pct Mn plus 0.15 pct Ca to magnesium resulted in entirely different textures than for the pure magnesium. The texture obtained for high-purity magnesium sheet showed the basal plane to be concentrated parallel to the rolling plane. The texture obtained for the alloy containing 0.20 pct Ca had the basal planes concentrated in elliptical areas whose centers were tilted 15" from the center of the pole figure toward the rolling direction. This split basal orientation was even more pronounced in the alloy containing 2.0 pct Mn and 0.15 pct Ca. Fuller and Edmunds" studied the rolled sheet textures in a zinc alloy containing 1 pct Cu and 0.01 pct Mn. The basal pole figure of this alloy contained a region of strong concentration not found in the pole figure for pure zinc.' In the above cases, results were discussed in terms of possible changes in slip and/or twinning systems and critical shear stresses. However, there were no experimental data to relate these speculations with the observed textures. It has been suggested that the deformation textures of titanium, zirconium, and beryllium could be directly ascribed to their low c/a ratios. The complex deformation mechanisms of titanium" also have been suggested to be characteristic of hexagonal close-packed metals with low c/a ratios. The purpose of this investigation was to study the cold-rolled sheet textures in binary titanium-base a alloys in which the c/a ratios were greater than, less than, and about the same as the c/a for iodide titanium. The annealed textures of these alloys will be reported in a subsequent article. Materials and Methods The chemical analyses of the metals used in this investigation are given in Table I. The alloys were prepared as 15 g buttons on a water-cooled copper block in a vacuum arc-furnace. The furnace was evacuated to pressures of the order of 10.' mm Hg, flushed with 99.98 pct pure argon, and melting was carried out in 0.2 atm pressure argon. Each button was remelted until radiographs and chemical analyses indicated complete solution of the solute elements. All buttons were forged and homogenized 72 hr at 500°C. The buttons to be rolled were ground and etched to sizes and shapes suitable for the rolling

Jan 1, 1954