Search Documents

By Glenn Alvey

THE measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value.. In its crudest application, the barrel-day price is determined by the "$10 to $.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the, barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the" $10 to $.01" rule is used extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc.

Jan 1, 1921

By Howard L. Hartman

6.1-1. Introduction. Of necessity, the first of the unit operations conducted during the exploitation phase in surface mining is production drilling. It precedes blasting, with which it is associated as the two unit operations employed to break or fragment consolidated material (usually rock) in place. The purpose of production drilling is to provide the cavity for placement of the explosives. So far, no alternative to blasting has been devised for fragmenting very resistant rock in situ, although some forms of excavation (ripping, bucket wheel) are suitable without prior blasting for softer rock, such as weathered shale or mudstone, decomposed sediments, etc. For the vast majority of surface mines, however, drilling and blasting are pre- requisite to excavation and essential to the production cycle. Drilling is also used in surface mining for purposes other than providing blastholes. It finds application during exploration for obtaining samples and during development for drainage, slope stability, foundation testing, etc. Only in the exploitation phase of surface mining, however, are unique or specialized drilling methods and equipment employed; and the discussion in this Section is directed primarily to that application of drilling. Drilling is the most common means of rock penetration, the operation of placing a directed hole in rock. Closely akin to drilling for exploitation purposes is the cutting or freeing of dimension stone in quarrying. This operation, usually termed channeling or sawing, also takes the form of directional penetration of rock; but instead of producing a cylindrical hole, it yields a kerf or cut. The material thus freed from the solid is both a shaped and sized product, an objective of vital importance in the dimension stone industry. In sawing, holes are sometimes drilled to insert tools, but this drilling is a minor part of the sawing operation and employs conventional methods. Cutting, as a unit operation for freeing stone in quarrying, may be considered equivalent in purpose to drilling and blasting in other forms of surface mining.

Jan 1, 1968

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By Edmund Shaw

In the year just past there were produced in the United States about 170,000,000 tons of sand and gravel. Much of this was pit-run material used for gravelling roads and as railroad ballast on lines that did not carry heavy traffic. But more than half of it was marketed as washed and sized, or graded, material. The methods used for preparing sand and gravel for the market have long been used in ore dressing and, as in ore dressing, depend on differences in the specific gravity of two substances or in the size or weight of particles. But many changes in the design and operation of plants and machines have been necessary. In ore dressing, the concentrate is only a small part of the feed; in sand and gravel washing, it is much the larger part of the feed. In addition, such close work as is needed when concentrating a metallic ore is not needed when washing gravel; the ability to put through a large tonnage is more important, and sizing, which is only a preliminary process in ore dressing, is an end to be attained. Rock crushers are found in most sand and gravel plants and they are used to break up the larger pieces from the deposit (known as boulders and cobbles) which are removed by a scalping screen. The crusher discharge is usually sent back to the scalping screen, the perforations in this screen setting the maximum size of the finished product. Washing Washing is to prepare sand and gravel so that they may be used as aggregates in concrete and wall plaster and in various processes in which impurities would harm the product. At one end of the scale of washed materials may stand ordinary concrete sand, which in some states may contain as much as 3 per cent, of clay and still be used in highway concrete construction. At the other end will stand the silica sand used for making plate glass, which must be washed so clean that the impurities that can be removed by washing do not exceed a few hundredths of a per cent. The methods and machinery that would produce one of these

Jan 1, 1926

By E. H. Dix

The purpose of this paper is to introduce the subject of Stress-Corrosion Cracking at the Joint Symposium of the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers. In this Symposium we are concerned with spontaneous cracking which results from the combined effect of high, prolonged stress, and corrosive attack. Stress-corrosion cracking may be considered a specific phase of the more general subject of the effect of high constant stresses in accelerating the rate of corrosion of metal products. The kindred subject of corrosion fatigue in which the life of a metal part under repeated stresses is reduced by corrosive attack is not a part of this Symposium. Likewise "creep," the failure of a metal part by high constantly applied stress, in the absence of a corrosive environment, is not to be included. How- ever, corrosive influences may have more effect on creep failures than is sometimes realized. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium.

Jan 1, 1945

By Stewart Coleman, Thomas W. Moore, H. D. Wilde

It is recognized that in the early days of the petroleum industry oil was produced with practically no scientific or fundamental knowledge of the laws and principles governing its extraction from the ground. Only a few, if any, of those exploiting the oil resources made any effort to collect accurate scientific information. There was little need for it, for as is frequently the case where the supply of a natural resource appears inexhaustible and is greater than the demand, large profits were possible from merely skimming the surface with little regard to the efficiency or thoroughness with which the oil was obtained. With this policy in force, great quantities of gas were wasted and when the reservoirs ceased producing by natural means they still contained a large fraetion of the oil originally in them. The present tendency in the industry is toward conserving existing oil reserves. In order that greater percentages of the oil present in the ground may be recovered, efforts are being made to improve production methods and to rework depleted fields. If the production methods are to be improved intelligently it is essential that the fundamental laws be known and understood, consequently large amounts of money and effort are being spent in gathering data that will serve to define and interpret these laws. A great deal of attention is being focussed on the study of the motion of oil through an oil-bearing sand, the forces that cause it to move and the factors that affect its motion. It is recognized that one of the important factors is pressure, but its quantitative effect is not known. In a given field the rate of production declines with time and so does the rock pressure. Furthermore, a comparison of different fields shows, as a

Jan 1, 1930

By L. C. Morganroth

From a geological standpoint, but scant attention has been paid to fire-clay beds. Only within the last few years have they been the subject of individual investigation, prior to this time having been considered only in their relation to coal seams. While the relative importance of coal and fire clay is still immeasurably in favor of coal, yet an industry as large as that of fire clay is entitled to a measure of attention. A discussion of the Carboniferous clays is practically a discussion of the clay beds in the Appalachian basin, since more than 90 per cent. of these clays mined are from this region. The clays are confined to the northern end of the basin, or the States of Pennsylvania, Ohio, Kentucky, Maryland and West Virginia, ranking in importance about in the order named. The clay deposits of the Carboniferous period have been divided into two classes; those found in the Pottsville conglomerate series of rocks, ' and all those that are found in the formations above, for the reason that the clay beds above the Pottsville series all resemble each other in properties, composition and appearance, and all are distinctly different from the bed found in the Pottsville formation. The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible.) Carboniferous clays occur between stratified rocks; sandstones, limestones, etc., in the same manner as coal veins. They are often accompanied by a coal vein although where the clay is of a workable thickness, the coal is generally too thin to work. The clay beds are sometimes known by the name of the coal seam at which horizon they occur. Clay beds may be from a few inches up to 20 ft. in thickness. They may consist of all soft clay, all flint or both soft and flint. The Carboniferous clay beds of Pennsylvania are the most important of any of the clay beds found in the country, and are among the oldest ones worked. We know more about this clay geologically for the reason

Jan 1, 1916

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919

By G. P. Walters, W. C. Fuller

THE production of thin films of beryllium became essential early in the irradiation program at Harwell in order to study the fundamentals of irradiation damage in this metal. In common with other metals, electron-microacope specimens of beryllium can be produced by different techniques. The techniques used to produce thin-film specimens varied according to the starting material. Most of the starting material was -0.060 in. thick. Large-area specimens (1 in. long by 0.5 in. wide) were chemically thinned to -0.005 in. thick in a solution containing 85 pct orthophosphoric acid, 10 pct chromium trioxide, and 5 pct sulfuric acid at 70°C prior to electropolishing. Small-area specimens, Fig. 1, had to be mechanically thinned prior to electropolishing because chemical thinning considerably reduces the area as well as the thickness. Mechanical thinning tends to produce a worked layer about 0.002 in. deep and hence this method cannot be used to thin bulk specimens below about 0.005 in. thick. Mechanical thinning is carried out by mounting the specimen on perspex then carefully polishing on wet grinding papers. Polishing is continued until about half the initial thickness is removed; the reverse side is then polished in a similar manner. After the bulk specimens have been mechanically or chemically thinned to -0.005 in. they are elec-tropolished in the solution shown in able I at 50" to 80°C. This solution should be prepared by adding the chromium trioxide to the orthophosphoric acid and then the glycerol last. The glycerol should be added slowly because a vigorous effervescence can occur. Electropolishing is carried out by holding the specimen in stainless-steel tweezers and gently agitating in the solution. Masking or "window" techniques are not required for beryllium, good microscope specimens being obtained from the edges of elec-tropolished foils. A stainless-steel beaker should be used, acting as the cathode and solution container. A closed circuit voltage of 30 v is used for polishing. Too low a voltage produces a matt surface and pitting occurs when it is too high. The solution temperature is important. If it is too low, the solution is viscous and bad polishing results and, if too high, etching of the specimen occurs. After electropolishing, the foils are thoroughly

Jan 1, 1963

By Roy Neal

THERE are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing, beds from sources in the same stratum and waters .that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by neighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may he unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in, question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position

Jan 1, 1919

By G. S. Morison

I have bad considerable experience with the testing-machine at the Watertown Arsenal, having had broken there sixteen large steel eye-bars, besides quite a number of iron bars and two compression members. So far as accurate mid satisfactory results are concerned, the machine is all we could ask for, and the officers who have it in charge, together with their civil assistants, are thoroughly conversant with it 1 details, and entirely competent to make the tests required. The principal defect is that the force is very inadequate. As the machine is arranged, tile weighing apparatus is at one end and stationary, the measure of strain being carried from this to the scale-beam by the fluid in a tube m small that it looks like a wire. At the other end is placed the hydraulic press by which the power is applied; this press is mounted on a small carriage and held by two eight-inch screws about four feet above the floor, which arc of course strained in compression during tensile tests, and in tension during' compression tests. When the stretch of the material has exhausted the throw of the plunger it is necessary to relieve the strain, draw back the plunger, and move the carriage along, which is done by nuts turned by steam working on the large screws. Every specimen placed in the machine must be lifted above the large screws and lowered into position. To do this, crabs, running on travellers, which span the entire room, are placed over the machine, and by these the specimen can be lifted and put in place. The actual time required to make a test depends largely on the amount which the material stretches, bat it may generally be said, that for specimens which will stretch from two to three feet the

Jan 1, 1882

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. $ deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks. Types of Items far Consideration On the hazard, or negative, side some of the common items to be considered are: 1. Subsidence and resulting damage. 2. Flo wage of water above that anticipated. 3. Geological. (a) Decline in quality of probable ore, and/or (b) Decline in quantity of probable ore. 4. Depressed economic conditions. 5. Litigation. Similarly, on the enhancement, or positive, side common items to be considered are: 1. Flo wage of water below that estimated. 2. Geological. (a) Increase in quality of probable ore, and/or (b) Increase in quantity of probable ore. 3. Elevated economic conditions. 4. Litigation. 5. Technological advance in the art. Tn all of the above items no consideration is given to placing a value on, or giving consideration to, possibilities. For example, referring to Table 1, the estimated normal present value (Vp) of a property, exclusive of risk consideration, is taken as $100,000. If subsidence affects the usefulness of the shaft, the present value of the property will decrease to $60,000, and it is judged that there is a 1 in 4 chance that the shaft will be impaired;, consequent.ly, if subsidence took place, the present value would be reduced ($100,000-$60,000) $40,000, but since the chance is 1 in 4, the allowable reduction would be only one-fourth of $40,000, or $10,000, or a discount of 10 pct (hazard factor) of the original value; the related safety factor is taken as unity minus 0.10, or 0.90. Thus, the original Vp, $100,000, multiplied by the safety factor ($100,000 X 0.90) gives $90,000, which is the adjusted present value of the property in this single instance. Additionally, there is a water hazard, which, if encountered, will reduce the present value to $85,000. The chance is 1 in 3. Following through with the same reasoning as shown above, the derived safety factor will be 0.95. To arrive at a single multiplying factor which will express the combined risks, the two safety factors are multiplied together, 0.90 X 0.95 = 0.855. That factor when multiplied by the origirial Vp will give the adjusted, and

Jan 1, 1950

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steel-making methods, the basic open-hearth process is one of the most versatile, both from the stand- point of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. In the case of some types of liquid-metal charges the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF THE BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SO2), manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course of the

Jan 1, 1944

By J. H. Reynolds

The possibility of using a semiconductor, metal, semiconductor structure as a light detector is discussed. A brief theoretical argument is presented which predicts that this structure should have pho-toresponse characteristics similur to those of a metal-semiconductor diode, but with the magnitude of the current increased by a transistor gain factor. Measurements made at low frequencies on a particulur S-M-S device agree u~th this prediction aizd shoul that significant gain factors are attainable. The current gain is substantially higher than that predicted for the metal base transistor. It is proposed that the operation of these units is more closely approxinzated by the metal-gate model which predicts higher current gains. A qualitative discussion of its high-frequency performance indicates that detection of light modulated at microwave frequencies by a S-M-S deuice is possible. ADVANCES in the technology of chemical vapor deposition'-4 have made it possible to form a S-M-S structure consisting of a thin metallic layer sandwiched between layers of single-crystal semiconductor. It has been proposed5-7 that, if the metal layer is made sufficiently thin, this structure could be used in an amplifier having several advantages over presently available transistors including higher-frequency performance. Calculations8 predict that the maximum gain-bandwidth product is nearly an order of magnitude higher than that of a bipolar transistor having the same geometry. Maximum oscillating frequencies in the microwave range are predicted. Electrical measurements made on S-M-S devices have shown that, although the theoretical frequency characteristics are not presently attainable, current and power gain is obtained. Another possible application of the S-M-S structure is its use in a light detector. This structure is a three-layer relative of the metal-semiconductor diode. Light detection using M-S diodes is the subject of considerable present interest. They are known to have a short response time and the ability to detect light having a photon energy below the semiconductor bandgap. In this paper, the mechanism by which S-M-S photocurrent is generated is discussed. An expression is derived which shows that the response characteristics are similar to those of a M-S diode, but that the magnitude of the current is increased due to the transistorlike behavior of the device. The results of low-frequency response measurements on a particular S-M-S structure are presented. These agree with the theoretical predictions and show that significant gain factors are attainable. A qualitative discussion of the high-frequency characteristics is presented which predicts that detection of light at microwave frequencies by a S-M-S device is possible. THEORY In this discussion, the photocurrent, iT, measured across terminals attached to the semiconductor emitter and collector layers is related to the current pho-toemitted from the metal base layer. The latter will be referred to as the primary photocurrent. The behavior of the primary photocurrent is determined by the characteristics of the two metal-semiconductor diodes. The diode photoemission is illustrated in Fig. 1, which shows the emitter and collector potential barriers. The metal thickness has been greatly exaggerated. As will be discussed later, the actual barrier shape can be much more complex, but this diagram illustrates the essential features of the photoemission process. An absorbed photon having an energy greater than the barrier height can emit an electron into the emitter or collector. Since this process is discussed

Jan 1, 1968

By R. A. L. Black

Rock mechanics is a very new science. It has been accepted as a recognized discipline for some two decades, but it is only within the last five to ten years that it has been common to include the teaching of rock mechanics as a separate subject in undergraduate curricula at universities. Thus, few senior mining engineers practicing in industry, either men in charge of production or those engaged in mine planning and design, are familiar with the subject. That this unfamiliarity has continued so long is also due in part to the fact that the results of rock mechanics investigations have been published in a large number of different periodicals covering subjects ranging from experimental stress analysis to obscure branches of applied earth sciences. The first really useful textbook ' in the English language was published only in 1965, in Canada. It made available to students and to practicing engineers, for the first time in concise form, the essential body of accepted knowledge about rock mechanics and developed the theories on which it is based in a simple, clear and logical manner. Another factor which has resulted in rock mechanics science being slow to be accepted by the mining industry is that research work has often appeared to be esoteric and unpractical. Senior engineers have been reluctant to spend money on the application of new knowledge when the process of application seemed uncertain and ill-defined, and where the cost of field investigations (which is necessarily high) appeared to offer no certainty of economic reward. This is a reasonable attitude on the part of mining engineers; they are responsible to skeptical boards of directors whose chief concern is, very properly, the net return on capital invested. The application of rock mechanics science has not in the past,

Jan 1, 1968

By O. C. Holbrook, George G. Bernard

A new theoretical treatment has been obtained for the behavior of pattern waterflood injection wells when closed in. Two cases are treated: Case I where oil and water are assumed to have the same properties, and Case 2 where they arc different. In applying the method, one plots log (p — p,) vs closed-in time, where p is well-bore pressure at any tims and p, is static pressure. The value of p. is determined by trial and error as that value which makes the plot linear at large time. A value for the permeability-thickness product can be determined from the intercept of this linear part, and a value of the skin factor from the injection pressure at time of closing in. Application of the method to data from water floods at three fields seems to give reasonable results. For the case of unit mobility ratio, it is proved that this new method should give the same value for permeability-thickness product as the conventional pressure build-up method. In addition, the new method gives correct values for static pressure, whereas the conventional method does not, often indicating negative static pressures. The new method may be used in cases where the surface pressure persists after closing in as well as in cases where it does not. INTRODUCTION It is of considerable interest and importance to be able to determine the characteristics of the reservoir in an area surrounding a water injection well. Thus, if we can determine early in the life of an injection well that there is a considerable "skin effect", remedial measures can be started before a full-scale pattern flood begins. Similarly, if it can be shown that a gradual buildup of skin effect is occurring with time, measures to free the water of plugging material can be taken. Determination of static pressure in the water-injection well may show that the water is entering a thief zone and not the desired reservoir. Finally, determination of the permeability of the sand around the injection well will allow estimation of the future relation between injection pressure and rate. It should be possible to determine average reservoir permeability, skin effect and static pressure from pressure fall-off data. However, at the time we began work on this subject, it was thought that no adequate theory on which to base such determinations' was available. According to the conventional method which considers the reservoir to be filled with one fluid of small compressibility (see Van Everdingen, Joers2, and Nowak2), shut-in pressure is plotted vs log where is injection time, and At is closed-in time. The physical significance of injection time, may well be questioned in this case, since in a reservoir completely filled with a single fluid (as required by this theory) and with input and output rates equal, the pressure behavior after an initial transient is independent of t,. Attempts by our Tulsa area to use this theory led to negative values of static pressure in most cases. Because of these limitations of the method discussed above, it was decided to attempt to develop a new theory of pressure behavior in water injection wells, one which would apply when there is a gas saturation, as is so often the case in water floods. In the following treatment the assumptions and basic equations are given first, then the method of application of the equations. A complete example is given to clarify details of application. All difficult mathematics has been placed in the appendices so that the reader can follow the text without difficulty. However, if he wishes only to apply the results without knowing the basis for them, he can learn how to do this from reading only the sections entitled "Plotting of Experimental Results" and "Example." ASSUMPTIONS AND BASIC EQUATIONS Statement of Problem It will be assumed that a horizontal layer of constant thickness contains in its pore system a mixture of oil, gas and water. While water is being injected into this pore- system through a well at constant rate, an oil bank is built up, gas being expelled from the space taken by the oil as shown in Fig. 1. The saturations within each

By F. F. Craig

A series of both welter and gas puttern Hoods was made in the laboratory to study the oil recovery performances of .such operations. These tests were contlrrctt~tl on consolidated sandstone models, using oil. water, and gas. The model floods were scaled to reprotlrrce field performance under gas arid water five-spot injection. X-ray shadowgraphs permitted observation of the gross fluid movement within the models. A method was developed for applying the mobility ratio concept to water flooding and dispersed gas drives in a five-spot well pattern. The area1 sweep efficiency. tit breakthrough for dispersed gas drives is much higher than previorsly expected, Iying in the range of 50 to 100 per cent. A method is presented for predictitig the water-oil ratio performance of five-spot pattern water flood., in uniform sands. This method is verified experimentally for the cotidition of 120 free gas initially present and for va1ues of gas saturation normally encountered in fields following depletion operations. Prodrrction perfort?zut~cc for pattern gas injection is also predictable by this method. INTRODUCTION In field pattern hater flooding or dispersed gas injection operations, the displacing fluid (water or gas) is injected and oil is produced through wells which are, area-wise. small openings in a large container or rescrwir of oil. As a result, not all of the area between the injection and producing wells is necessarily contacted by the injected fluid by the time it first reaches the producing wells. The question arises in predicting oil recovery. as to what traction of the pattern area involved is contacted by either the injected water or gas due to the relative position of the injection and producing wells. This is the areal sweep efficiency. It is also desirable to know how well arrangement affects the oil production performance. A solution to this problem has been attempted by many means. Mathematical analysis¹,²,³, and electrolytic models', have been used to establish a breakthrough areal sweep efficiency of 73 per cent for a five-spot pattern in which the ability of the oil to flow ahead of the invading fluid is equal to the ability of the invading fluid to flow in the invaded zone. All of these studies simulate only one of many field conditions. Improved studies of areal sweep efficiency at breakthrough were made using the fluid mapper5, poten-tiometric models" and X-ray shadowgraph techniques. In these it was possible to study the effect of variations in mobility of the injected and displaced fluids, and so to cover a wide range of field conditions. The limitation of these studies is that, with these models, it was not possible to simulate the saturation gradient behind the flood front when oil is displaced by gas or water. In the most recent published technical paperS on the subject, a method was presented for predicting the oil recovery performance after breakthrough in a five-spot pattern water flood. The method involved correlations which were obtained experimentally using miscible fluids. One limitation of this work was that a saturation gradient, usually found in immiscible fluid displacement, was absent in these studies. Also the laboratory studies did not cover the situation of a water flood following oil recovery by depletion drive. as is the situation in most field water floods. The tests reported in this paper were made using oil. water, and gas, thus eliminating the simplifications of former studies. Also reported are laboratory studies on

Jan 1, 1956

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is

By C. M. Young

WHEREVER salt is extracted from the ground as an artificial brine produced by pumping down fresh water to dissolve the salt, subsidence of the overburden is a possibility, though apparently few cases of such subsidence have been noted and detailed records are wanting. This description is intended as a record of subsidence that may permit the forcasting of similar occurrences in other cases; the data were supplied largely by R. B. Lee, city engineer of Hutchinson, Kans. About eleven years ago, ground movement occurred at a neighboring salt plant, when the surface assumed the form of a shallow funnel. Movement was probably due to a flow of sand into a well through a poor seal or a broken casing. The salt deposit increases in thickness from the east until at Hutchinson, where the subsidence occurred, it is about 310 ft. think. The interbedded layers of shale vary in thickness from mere traces to about 7 ft. While knowledge of the shale content of the beds is not exact, the log of a shaft 3 miles east of Hutchinson indicates that shale forms about 25 per cent. of the total thickness. This shaft does not reach the bottom of the salt by about 60 ft., but there is no reason to think that the lower part of the bed is different from the upper. Logs of wells sunk to the bottom are not sufficiently detailed to be of much value. Above the salt is the shale of the well-known Red Beds. The thickness of this is variable, principally because of its eroded surface, but at the mine it is 340 ft. This shale is variable in character and strength, but contains no strong members of limestone or sandstone. If the support is removed, very probably it will subside. The Arkansas River flows across the salt district and Hutchinson is situated on the flood plain. Between the top soil, which is about 8 ft. thick, and the shale is 60 to 100 ft. of water-bearing sand and gravel.

Jan 2, 1926