Search Documents

By Douglas Ashmead

In his paper Mr. Braley makes no mention of the bacteriological aspects of the problem. It is now quite well established that certain bacteria play a major role in formation of acid mine waters, and it is a simple matter in the laboratory to show that under sterile conditions the rate of acid production from a pyrites suspension is only about one quarter of that obtained from a similar suspension inoculated with drainage from a mine producing an acidic pit water. Under sterile conditions the oxidation is due to direct chemical action and, from the evidence just given and from much other evidence, this increase under nonsterile conditions is due to certain bacteria. Experiments recently completed, and shortly to be published, have shown that this bacteriological oxidation can be prevented by the maintenance of pH conditions above 4. It was found that to raise this pH above 4 at the beginning of the experiments was not sufficient but that, due to the continuing chemical oxidation, alkali had to be added daily to maintain the pH conditions above 4. The amount of alkali added, however, over a fixed period, was only about one quarter of the alkaline equivalent of the acid produced when pH conditions were not controlled over an equal period. The opinion expressed by Mr. Braley that sodium hydroxide has little or no effect on the rate of oxidation of pyrites is not substantiated by the above experiments. The writer does not claim that these results show a practical solution to the problems, especially in abandoned workings, but feels that the application of an alkaline coating, such as lime wash, to exposed accessible workings might be well worth trying. S. A. Braley (author's reply)—In 1919 Powell and Parrl suggested that bacteria, or some catalytic agent, hastened the oxidation of pyritic or marcastic sulfur in coal. Carpenter and Herndon (1933)' attributed the action of Thiobacillus thiooxidans. Colmer and Hinkle (1947)3 observed an organism similar to T. thiooxidans and another organism that oxidized iron. Leathen and Braley 9rst discovered this organism in 1947 in a sample of water from the overflow of the Bradenville mine (Westmoreland County, Pennsylvania). They characterized the organism in 1954" and gave it the name Ferrobacillus ferrooxidans. Although Temple and Colmer (1951)' had suggested the name Thiobacillus ferrooxidans, since they claimed it oxidized both ferrous iron and thiosulfate, we have found that pure cultures of the organism do not oxidize thiosulfate, hence the name F. ferrooxidans. In 1955 Ashmead7 isolated an organism, similar to the one called Thiobacillus ferrooxidans by Temple and Hinkle, from acid mine water in Scotland. It is probable that this organism was F. ferrooxidans. In 1954 Bryner, Beck, Davis, and Wilsonh reported microorganisms in effluents from copper mine refuse. These organisms appeared to be similar but were not in pure culture. In view of this history of bacterial investigation of acid mine water and our own ten years of experience, we do not agree with Mr. Ashmead that bacteria play a major role in acid formation. We do not find that any of these bacteria will directly oxidize pyritic material. They do, however, augment the chemical formation of sulfuric acid by atmospheric oxidation. In two papers in 1953% eathen, Braley, and McIntyre discuss the role of bacteria in acid formation and postulate the mechanism through which they operate. Mr. Ashmead in his discussion of my paper has assumed that this work was carried on in the presence of acid mine water in which bacteria would be present. This was not the case. Strictly sterile conditions were not maintained, but the organisms present in mine drainages were definitely absent in these experiments. We believe that we have demonstrated that alkalis do not inhibit the chemical oxidation of pyritic material. This is also indicated by Mr. Ashmead's discussion in which he says that alkali must be added daily due to the continuing chemical oxidation. It is interesting to note that Mr. Ashmead finds that maintenance of pH above 4.00 decreases the activity of the bacteria. We have found also that a decrease in pH below 2.8 also inhibits its activity. Table XIII of published data'" illustrates the decrease in activity with increased acidity, although pH values are not given. These values are in comparison with uninoculated controls and show the marked increase in acidity up to 22 weeks but a decline at 29 weeks, at which time the experiment was terminated. It is probable that after a longer period only chemical oxidation would have continued. From our studiesv we have postulated that the iron oxidizing bacterium (Ferrobacillus ferrooxidans) oxidizes the ferrous iron, resulting from chemical oxidation, to ferric iron. The ferric iron then aids the atmospheric oxidation of the sulfuritic material and is itself reduced to ferrous iron, which in turn acts as food for the autotrophic bacteria. Study of the physiologic properties of F. ferrooxidans shows that its preferred pH is about 3.00 and its activity decreases with variation in either direction. It is extremely inactive above pH 4.00 and below 2.5. This inactivity above 4.00 is indicated by Mr. Ashmead's observations. These properties of F. ferrooxidans then correlate perfectly with our hypothesis. Ferrous iron is oxidized very slowly by atmospheric oxygen in highly acid sohtion and since the bacteria become inactive, acid is formed only by atmospheric oxidation. At a pH of 4.00 or above iron is more readily oxidized by atmospheric oxygen, but the bacterial activity is decreased. However, with a pH above 4.00 the ferric iron is removed from the field of activity since its soluble sulfate hy-drolyzes and precipitates the iron as ferric hydroxide or a basic sulfate. As we have shown in the paper under discussion, the alkali does not inhibit the chemical oxidation, and thus the acid formation continues. This

Jan 1, 1957

By R. L. Orr, O. D. Sherby, J. E. Dorn

Creep data for pure metals at temperatures above those at which rapid recovery occurs (above about 0.45 the melting temperature) are correlatable by means of the equations and These correlations were applied successfully to data for aluminum, iron, nickel, copper, zinc, platinum, gold, and lead as well as for simple alloys. For a given metal, AH is a constant about equal to the activation energy for self-diffusion. THE early recognition that creep is stimulated by thermal activation prompted numerous investigators', ' to apply the same laws that are valid for the viscous behavior of liquids to analyses of creep data. To a good first approximation these laws are summarized by the equation were i is the creep rate; T, the absolute temperature; R, the gas constant in cal per degree per mol; T, the applied stress; AH, the activation energy in cal per mol; S', a constant dependent on the entropy of activation, the frequency of activation, and the contribution of each activation to the strain; and B', a constant dependent upon the size of the flow unit that is activated. Although Eq. 1 describes the flow of viscous fluids very accurately, its application to the creep of solids has been disappointing. Two reasons for the failure of Eq. 1 for creep are now known: First, the decelerating creep rates during primary creep demand that the internal structures of the metals are changing and that these changes might be reflected by changes in one or more of the three creep parameters S', AH, and B'. Consequently when the conventional methods of evaluating these parameters are employed by comparing the secondary creep rates at a series of temperatures and at a series of stresses, the true effects of temperature and stress are masked because of simultaneous changes in one or more of the creep parameters. Second, as will be illustrated more fully later, three distinctly different types of investigations have shown that the stress term for high temperature creep enters the analysis as and not as t/T. This rather unexpected result points sharply to a significant fundamental difference between the mechanisms for the viscous behavior of fluids and the high temperature creep of metals. More recent extensive investigations",'4 on the creep of high purity aluminum and several of its dilute a solid solutions have shown that where E is the total creep strain; temperature compensated time = for a constant temperature test; t, is the initial stress in a constant load test or the constant true stress in a constant stress test;" and t is the duration of test. • Eq. 2 is valid for either constant stress or constant load tests; but the total creep curve is difierent (i.e. the function, f, is differentl for each test. The fundamental origin of the validity of Eq. 2 is thought to arise from some equivalence of substructures in constant load creep tests at equal values of 0 or E. Both X-ray and metallographic examination revealed that practically identical lattice distortions and subgrain sizes are obtained for the same creep strain under the same load over wide ranges of test temperature.' Furthermore the room temperature tensile properties following equal creep strains at different temperatures under constant loads were also identical, illustrating that identical substructures were indeed obtained.' " A second type of correlation was obtained by differentiating Eq. 2 with respect to time, giving For the secondary creep rate, denoted by i,, But Eq. 2 reveals that 0, is a function of a, alone because the secondary creep rate in a given constant load test is always reached at a fixed value E,". Therefore where is the function that was introduced a number of years ago by Zener and Hollomon." Eq. 4 is not only valid for creep but will permit correlations between constant load creep and tensile data where e, is the rate of tensile straining and (TC is the engineering ultimate tensile strength.

Jan 1, 1955

By William M. Newton, John E. Sherborne

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By R. V. Ramani, R. M. Mishra, Y. J. Wang

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solution. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning. Starting from an initial system with no leakage and one fan, more complex ventilation networks with several leakages, sections and fans, are analyzed to show that ventilation system design on the basis of total systems approach is the correct procedure.

Jan 1, 1979

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development of the Trombetas deposits by Alcan. A general report of the Trombetas Project has already been published in E/MJ(Anon. 1975) to which the reader is referred for details on ownership, infrastructure and construction as well as the proposal for mining and treating the bauxite. A regional account of bauxite in and around the Guyana Shield and the northern part of the Brazilian Shield is included to help explain the geology of the Trombetas deposits and their relation to other bauxites in northern South America. It is suggested that all these deposits formed during Tertiary time under similar geologic conditions.

Jan 1, 1979

By C. A. Heiland

A. INTRODUCTION (C. A. HEILAND) I. PRINCIPLES OF TEMPERATURE COMPENSATION IN MAGNETIC INSTRUMENTS The principle underlying the majority of magnetic intensity variom-eters is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechan-ical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection a is given by tan a = F/X, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment µ (see equation 1). The second effect is due to the change in the .torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1932

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world's notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world's great mines.

Jan 1, 1981

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By James K. Greenlee, David W. Wisecarver

It is estimated conservatively that some 14 billion tonnes of coal reserves in the United States exist in beds considered steeply dipping, i.e. at pitches or slopes in excess of 15O - a slope too steep for practical use of mobile wheel or crawler drive mining equipment. Past attempts to mine these steep reserves are limited owing to production difficulties and high costs, an expected result when mining of slopes must be done conventionally and mining on strike with mobile mining equipment is restricted because of limited cross sectional opening and operating room. In Europe, these adverse conditions are countered through the use of the longwall mining method. In fact, longwall mining is employed along pitches up to 55°. However, both operating and administrative - conditions in foreign steep seam coal mines differ from ours in that (1) the mine does not necessarily have to make a profit and (2) single entry development of retreat mining panels is acceptable practice. In the United States development can be done with a minimum of two entries only, provided belt haulage is not used during development.

Jan 1, 1981

By George P. Chapman

Mica is a platy mineral occurring in a variety of complex hydrous aluminosilicate forms with differing chemical composition and physical properties. Principal minerals in the mica group include: Muscovite-potassium mica (colorless or pale green/ ruby) Phlogopite-magnesium mica (dark brown or amber) Biotite-magnesium-iron mica (black or dark green) Lepidolite-lithium mica (lilac) Selected properties are given in Table 1. Muscovite is most important commercially with phlogopite of lesser use. The laminated structure of mica enables it to be split into very thin films which are transparent and tough as well as having outstanding dielectric and insulating properties. Commercially, mica is used in a number of forms (Chowdbury, 1941; Rajgarhia, 1951; Skow, 1962). Sheet mica consists of flat sheets mined from naturally occurring books of mica, free from defects and capable of being punched or stamped into required shapes. Sheet mica is separately classified into blocks, films, or splittings according to thickness. Built-up mica, or micanite, is made by arranging overlapping splittings in layers , cemented with a binder and pressed together at high temperature. Reconstituted mica, or mica paper, is made by depositing fine flakes of high-quality scrap mica in a continuous film impregnated with binder. Scrap and flake mica are normally unsuitable in quality or size for making sheet mica. Originally the term scrap mica referred to the waste byproduct of mining and fabricating sheet mica, and distinct uses were developed for this material. Subsequently it became economically feasible to mine lower quality mica for these uses, and the term flake mica was introduced. Although the two terms are still used somewhat synonymously, it is considered better, at least in the United States, to use the term flake mica in referring to mica mined for uses other than as sheet mica; and to restrict the term scrap mica to mica mined for or with sheet mica, but which will not meet the specifications. Synthetic mica, such as fluorophlogopite, is produced by slow crystallization of a melted blend of pure raw materials. Mineralogy In the true sense the term mica does not relate to, a particular mineral, but to a group or family of minerals of similar chemical composition and to some extent similar physical properties. These minerals are predominantly potassium aluminum silicates with varying amounts of magnesium, iron, and lithium. The precise formulas and isomorphic relationships of the various group members have been studied, but general agreement has not been reached (Grimshaw, 1971; Hurlbut, 1952; Skow, 1962). The general formula describing the chemical composition of micas is [X2Y4-6Z8020(OH, F)4, where X is mainly K, Na, or Ca; Y is mainly Al, Mg, or Fe; Z is mainly Si or Al (Deer, et al., 1962).] These minerals have an internal structure of the layered lattice type where the silicon atoms are in the center of a tetrahedral grouping of oxygen atoms. The groups are linked together in a single plane by three oxygen atoms that lie within the common plane. Each of these oxygen atoms is shared by two tetrahedra. These linked tetrahedral groups, when continually extended, produce a hexagonal network within the plane. This internal structure of the mica has been used to explain the ex-

Jan 1, 1983

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand these has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of —200 mesh material in the final product markedly increases costs of de-watering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins. Wasting of coal in the -200 mesh slimes may account for a loss in washer yield equivalent to 2.0 to 2.5 pct of the raw coal input. With rising mining costs the value of such a loss is constantly increasing and a need for a better solution to the fines problem becomes more pressing every day. From an operating viewpoint, also, continuous removal of extreme fines from the washing plant circuit permits good water clarification practice, improving significantly the overall cleaning efficiency. The obvious desirability of recovering a commercially acceptable coal from washery slimes prompted U. S. Steel Corp. to investigate the merits of the Convertol process developed in Germany." Although this process has been used commercially in Europe for some time, little if any consideration has been given to its possible adoption in the U. S. until very recently. Fundamentals of the Convertol Process: In the Convertol process, droplets of dispersed oil are brought into intimate contact with the solids suspended in the coal slurry to be treated. This contact causes oil to displace the water on the surface of the coal by preferential wetting, or phase inversion, after which the coal particles are allowed to agglomerate in a manner permitting their re- moval from the slurry by centrifugal filtration. The clay and other particles of mineral matter suspended in the slurry do not have the affinity for oil the coal particles have. Consequently the oil treatment is preferential to coal to the extent that more than 95 pct of the oil used reports with the clean coal recovered. Figs. 1 through 3 will clarify the steps involved in the process. Fig. 1 shows the suspended material in the slurry to be treated, which is a thickened product containing 40 to 45 pct solids. Oil is now injected into the slurry under vigorous agitation to produce good oil to coal contact conditions, which result in preferential oiling of the coal particles. These coal particles are then permitted to agglomerate by gentle stirring in a conditioner to form flocs, as shown in Fig. 2. At this point in the process the agglomerated oiled coal can be washed and partially dewatered on a vibrating screen, as shown in Fig. 3. Finally, the washed flocculate can be further dewatered in a high-speed screen basket centrifuge or in a solid bowl centrifuge. Commercial Application of the Convertol Process in Germany: The original Convertol process was developed by Bergwerksverband zur Verwertung von Schutzrechten der Kohlentechnik, G.m.b.H., a German research organization controlled by the Coal Operators Assn. of the Ruhr Valley. The process as reduced to commercial practice in Germany' is shown in Fig. 4. In this process a thickened slurry (40 to 45 pct solids) mixed with a predetermined percentage of oil is fed from a surge tank to the phase inversion mill. After the phase inversion step, the slurry is usually discharged directly to a highspeed screen centrifuge. From 3 to 10 pct oil is used, depending on type of oil, size consist of coal to be recovered, and operating temperature. The top size of fine coal cleaned in Germany by the Convertol process is limited by the size of the openings in the centrifuge screen basket. Any mineral matter coarser than the basket opening, which is generally 60 to 80 mesh, must remain with the oiled coal. If the coal fines have been effectively cleaned down to about 80 mesh, the cleaning performance of the process is practically unaffected by the presence of coarse coal particles. However, since recovery of coal much coarser than 80 mesh is mow economical by conventional methods, it normally becomes more costly to allow substantial percentages of this coarse coal in Convertol process feed. Where the general plant layout does not permit effective cleaning of coal sizes down to 80 mesh or lower. there is some justification for a coarser Con-

Jan 1, 1959

By J. Jones-Parra

In previous Technical Notes, W. R. Rose' and W. Purcell have discussed the capillary pressure data presented by Welge.' Welge obtained capillary pressure curves of the imbibition type in which it was necessary to apply to the apparent wetting phase a greater pressure than that of the non-wetting phase to complete the cycle and reduce the non-wetting phase saturation to low values. Rose suggests in his Note that conditions of equilibrium could not have prevailed, since the. non-wetting phase pressure must always be the greater. Pur-cell in his Note, proceeds to postulate a pore system consisting. of a series of "holes in a doughnut," in which he contends that under equilibrium conditions it is necessary to resort to negative capillary pressures before significant wetting phase displacement can take place. There is a remarkable similarity between the shape of the capillary pressure curve calculated by Purcell and those measured by Welge. It is the purpose of this Note to show that, because Purcell neglected to account for the behavior of the residual wetting phase saturation, his system was not in equilibrium during imbibition; and, furthermore, that if his system had been in equilibrium, negative capillary pressures would not have been possible. In Purcell's pore system, the residual wetting phase will form pendular rings at the interstitial spaces existing somewhere within the system, for example, such as those spaces between "doughnuts" as shown in Fig. 1. The true capillary pressure is that across the pendular ring interface, and for the system to be in equilibrium the pressure drop across all interfaces must be the same, including that across the interface in the tight pores A of diaphragm B (Fig. 1). As the pressure across the cell is reduced, the advancing interface will move into the pore from the diaphragm, but at each pressure, the curvature of the pendular rings must be the same as that of the advancing interface if equilibrium is to prevail. Since equilibrium conditions are the basis for the entire argument, it follows that pendular rings must grow as wetting phase enters the pore, that is, as the pressure across the cell is lowered. In Purcell's calculated curve, the residual wetting phase saturation remains constant as the capillary pressure decreases. Thus, his curve does not represent an equilibrium process.

Jan 1, 1953

By Ronald D. Hill, Roger C. Wilmoth

The neutralization of acid mine drainage is becoming a common practice in the eastern United States. Over 200 plants are now in operation. Lime is the neutralizing agent utilized in most treatment plants; however, limestone may have an economic and practical advantage. Current research efforts of the Federal Water Quality Administration, both inhouse and through grants, to develop and demonstrate the use of limestone are reported. In essence, a state-of-the-art review is presented.

Jan 1, 1972

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953