Search Documents

By S. H. Ash

With statistics still incomplete, it appears that the safety record of the mineral industry for 1955 will do well to hold its own in comparison with 1954. On the one hand, metal mining shows an improvement in its record, due in part to intensive campaigns for preventing ground fall accidents. Coal mining, on the other hand, is showing a poorer record in 1955 than for the preceding year. While no major disasters occurred during the year, increased fatalities resulted from ground fall, haulage, and machinery accidents. It seems probable that increased job training may serve to improve the situation. Health: Utilization of diesel equipment continues to increase in noncoal mines, in spite of existing prejudice. In 1955 two types of diesel-driven tractors and one shuttle car were approved by the USBM. Where diesel engines are used controlled ventilation is mandatory in order to keep the CO content under 20 ppm, but such ventilation is not difficult to achieve with normal equipment.

Feb 1, 1956

By S. R. Elliott

THE principles of the caving system, as they apply to mining of soft iron-ore deposits, are well known, as this method has been in use for many years. It is, however, necessary to give a general description of it before describing the Athens method. The shaft and surface equipment should be placed at a sufficient distance from the orebody, so that the caving and pulling of the surface will not disturb the operations of the mine. Levels are started at the proper intervals, and when raises are completed, slicing commences at the top of the orebody and progresses downward. The necessary precautions are taken to avoid the occurrence of large open rooms and it is customary to break sufficient capping to form a mat to prevent heavy falls of ground from crushing through to the lower sublevels and endangering the lives of the workmen. Slicing is continued, and when sufficient width and length are undercut, the capping commences to cave, and in time a settlement occurs at the surface. As soon as this caving commences, the pressure on the timber naturally increases; after it extends to the surface, the amount of pressure has a certain relation to the depth. In other words, the pressure increases with the depth, but not in direct proportion. At great depths, such as that found at the Athens, 2500 ft. (760 m.), the pressure might be so excessive that the cost of keeping working places open would be prohibitive. The actual caving of the surface in a deep mine, with a great thickness of capping, is slow and often takes years to accomplish. After sufficient width and depth -have been undercut, the capping starts to break away, but through arching large masses of rock-.fill the opening, support the capping, and retard the continuation of caving. Caving to the surface is, therefore, retarded until either a sufficient thickness of the orebody is removed, or the width and length of the undercut part have been greatly increased. I wish to emphasize this fact of slow caving, for it is on, this principle that the success of the Athens system. largely depends.

Jan 8, 1920

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By Ralph Hayden

I. INTRODUCTION. IN the wet concentration of ores there is always a certain amount of very fine material with which to contend, and which invariably carries such quantities of value that the treatment of it is worth while; commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely, the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 8, 1913

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method.

Jan 8, 1950

By Frank Clemens Smith

The occurrence of the tellurides of gold and silver, even in small quantities, is so rare that their metallurgical treatment has engaged little attention. A residence of several months at one of the few mines in North America the product of which consists entirely of such ore, has led me to arrange a method for its economical treatment. The mine referred to is the Huronian, situated a few miles distant from Jackfish Lake, in Ontario, Canada. The plan proposed is for this peculiar case, and is put on record as possibly suggestive and helpful .in any similar instance, should it occur. Since freight-rates from the mine to the nearest railroad-point were extremely high, and for other economical reasons, the method proposed is modified by the use, as far as possible, of the machinery already at the mine, and is so arranged that bullion instead of concentrates would be obtained as a final product. The ore-vein at the Huronian mine varied in width from about 4 feet at the surface to 2 feet and less at the lowest level—125 feet —and dipped southeast about 88. The rock consisted, on both foot- and hanging-walls, of soft, green Huronian slates carrying much highly crystalline but barren pyrite. The ore carried an inconsiderable amount of galena with iron and copper pyrites, argentite, hessite, sylvanite (or petzite), and probably altaite, the telluride of lead. Near the surface the ore showed considerable native gold, but this disappeared with greater depth. Two complete analyses of minerals containing tellurium are here attached, as they establish the presence of two important compounds: I. Analysis of a mineral supposed at the mine to be sylvanite, but agreeing more closely in composition with petzite (Ag, Au)2 Te: Ag = 41.062 Au =23.691 Te =32.007 Pb = 0.071 SiO2= 0.097 Fe = trace 96.928

Jan 1, 1890

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources fortunately are supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for special purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Charles Hayden Memorial Fund, designated to further the education of Student Associates, the Rocky Mountain Fund, and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowment funds of the Institute through a standing, committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1940

By N. J. Themelis, A. W. Last

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early 1930s in the so-called Hadsel mills (Hardinge, 1955) as seen in [Fig. 1], mainly used in gold mines on the US West Coast. A number of these mills were built in sizes of 6.1 to 7.3 m (20 to 24 ft) in diameter and 1.5 to 1.8 m (5 to 6 ft) in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill, the Aerofall dry grinding mill, and others. A tabulation of all known autogenous and semiautogenous installations around the world was sent recently to the authors by G. J. Kushner of Koppers Metal Processing Division. In the size range of 7.3 to 9.8 m (24 to 32 ft) in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 11.1-m-diam X 4.6-m-long (36-ft-diam X 15-ft-long) mills in Minnesota, powered by 8950 kW (12,000 hp) motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above 150 mills was in operation prior to 1964. Grinding rates in autogenous mills are very sensitive to variations in ore breakage characteristics and even with fairly constant ore type can exhibit large fluctuations in throughput. Autogenous grinding also depends on availability of a fraction of the ore to be ground in the form of "competent" rock which can withstand to a certain degree the tumbling and impact action within the mill. If the ore is uniformly "soft", it will soon be crushed into small size particles and further grinding, which depends on the existence of large size rocks in the mill, becomes impossible. This apparently is the case with most copper ores, as discussed by Bachman, Last and Nabbs (1970) who described pilot testing of a large number of ore samples from Kennecott 's Chino Mines. Under circumstances where autogenous grinding is impractical, it is possible to realize most of its benefits by utilizing large grinding balls in place of the "competent" rock and practice what has become known in the mining industry as semiautogenous grinding. In semiautogenous grinding (SAG), a grate discharge tumbling mill is fed the product of a primary crusher or run-of-mine rock. Forged steel or alloy grinding balls, in proportions ranging from 3.10% of the total volume in the mill, are used to complement the self-grinding ability of the ore. Semiautogenous circuits can be either designed for single-stage closed-circuit grinding which produces a final product for recovery processes, or for two-stage operation in which the SAG mill product is fed to a second stage of grinding in a conventional ball mill.

Jan 1, 1981

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By L. S. Darken

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By G. T. Jackson

PROPERTY AND LOCATION THE Alaska Gastineau Mining Co.'s mine is located at Perseverance, about 4 mi. east of Juneau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 in.). It is shown in Fig. 1. FIG. 1.-ALASKA GASTINEAU MINING CO.'S PROPERTY NEAR JUNEAU. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone.

Jan 9, 1919

By A. L. Bollens, R. H. Johnson

The appraisal of oil wells, now that we have the age-size method of making composite decline curves, and the present worth of successive time units method of valuation, has its greatest remaining uncertainty in the difficulty of extending into the future the price curve and the composite production curve. The point of attack in this paper is the carrying on (or extrapolation) of the production curve. Led by the valuable discovery of Lewis and Beal that the decline curve is nearer the hyperbolic class, y = (x + a)-", than any other form, the current practice is the graphic method. The data are plotted on logarithmic paper and shifted with successive trials until the line becomes straight. This straight line can then be extended into the future. The method was a great help during the period when, for tax purposes, there was need for a quick method even though the errors were large. Now that we seek greater validity in our methods we find the following faults with the current method. 1. Where the shift is great (it exceeds 10 in some cases) the scale cannot be read with the necessary precision so that the resulting data would give a very irregular and inaccurate curve. 2. Where the curve cannot be straightened on logarithmic paper because of sigmoid shape the method has a serious systematic error. We believe the sigmoid curves to be more common than usually supposed, indeed when one considers the number of variable causative factors this is to be expected. We have therefore been seeking a method that is free from these difficulties and yet not so laborious as fitting a curve to the data and the calculation from the formula which, since it involves looking up logarithms, is unduly time-consuming. The method here described has been developed on the basis suggested by Earl Oliver, that the amount of oil produced per month or year for each reduction of production of a barrel of oil per day could be plotted to advantage. A step forward was made by Earl Carpenter in this laboratory, and some of the

Jan 1, 1928

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By J. L. Huiatt, R. B. Tippin

Introduction Great Salt Lake Minerals & Chemicals Corp. (GSL), a subsidiary of Gulf Resources & Chemical Corp., is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, UT. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt, and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The CSL Sulfate of Potash Complex: The GSL potash complex (depicted in [Fig. 1]) is divided into a solar evaporation pond system and the process plants. The solar evaporation system consists of a 17,000-acre (68.8 km2) ponding operation where the various salts deposit during the summer evaporation season and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit containing primarily kainite (KC1 . MgSO4 . 3H20), schoenite (K2SO4 . MgS04 . 6H20), and halite (NaCI), with some carnallite (KC1 . MgC12 . 6H20) and epsomite (MgSOq . 7H20). Other minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content can vary greatly. During an "erratic" evaporation season, with intermittent summer rains or

Jan 1, 1980

By H. Eyring, J. W. Fredrickson

Many theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying.certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.' ZenerZ has reviewed and correlated the existing work on the anelasticity of metals. With these and others3'4'5 resent theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,l Smekal,8 Polanyilg Orowanlo and Taylor.'' Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic" process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome ''one at a time," in a manner of speaking, due to some stress-concentrating effect.13 Proposed Theory Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces.

Jan 1, 1949

By Henry Eyring, Jay W. Fredrickson

MANY theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.1 Zener2 has reviewed and correlated the existing work on the anelasticity of metals. With these and othersa3,4,5 present theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,7 Smekal,8 Polanyi,9 Orowan10 and Taylor.11Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome "one at a time," in a manner of speaking, due to some stress-concentrating effect." PROPOSED THEORY Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In. this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces. .

Jan 1, 1948

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939