Search Documents

By F. J. Lecznar

An investigation of the problem of separating two minerals by a moving inclined plane has revealed that only minerals with considerable difference in sliding friction coefficients separate readily; that it is possible to separate two minerals when only one of them has a rolling friction coefficient; that difference in geometrical shape of the minerals is important to separation which improves as grain size increases; and that the thickness of the stream falling on the belt influences the grade of separation - the thinner the stream, the smaller the interference between the grains of the minerals to be separated and the higher the degree of separation. The problem of separating two minerals with different friction coefficients and shapes by a moving inclined plane has been investigated. Friction separators can be used to separate two materials that differ in shape and in friction coefficient. 1,3 Gladkov has presented some theoretical aspects of using a moving plane to clean corn and podded seeds; this method, however, did not result in practical application. When considering the separation of minerals, only those with considerable difference in sliding friction coefficients can be taken into account. Furthermore, it is possible to separate two minerals when only one of them has a rolling friction coefficient. The difference in geometrical shape of two minerals is also important to separation. It has been found that the separation of two minerals improves as the grain size increases. For example, coal and slate over 2 in. in grain size separate much better than materials of smaller grain size. As Table I indicates, the slate grains smaller than 25 mm gradually lose their flat shape with decreases in size and are more rounded than larger grains, which are almost flat. The smallest grains of slate in first and second fractions slide down the belt since their friction coefficients decrease and approach the value of the rolling coefficient. The percentage of separation of the first fraction is, therefore, low. Thickness of the coal stream falling on the belt also influences the grade of separation; the thinner the stream, the smaller the interference between the grains of the two minerals to be separated and the higher the degree of separation.

Jan 1, 1963

These springs arc situated on the south bank of the river about four miles below the City of Great Falls. In addition to the spring on the bank there are several in the bed of the river. Estimates on the flow of all these vary from 350 to 600 cubic feet per second, and as the temperature is practically constant at 53° F. throughout the year, the effect on the river water is to prevent the formation of anchor ice at the Rainbow Fails power development below, trouble of this source being in evidence every winter at the Black Eagle Falls above. Geologists claim that the water of the Giant Springs is derived from seepage through an old pre-glacial channel of the Missouri River now occupied by Sand Coulee, five miles up-stream from Great Falls. The water in this buried channel seeps through the flat-lying sandstone of the region and again unites with the present stream at the site of the springs.

Jan 1, 1913

By Henry Howe

THE brilliant and very original matter in Professor Jeffries' discussion ? should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries' hypothesis. The very features of Professor Sauveur's photographs which fit this hypothesis so exactly are reproduced in Chappell's photographs of steel coarsened under somewhat different conditions. 1 The ideas developed by these discoveries are so novel that conven- ience of language seems to call for new conventional terms for expressing them. In, what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries' hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progressively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then. an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called "supergerminant" if the distinction should be needed.

Jan 12, 1916

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thick-ners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter. It is quite apparent from reading the literature that Coe and Clevenger's contribution is not generally appreciated. In so far as the basic engineering relationships are concerned, the only real advance which has occurred in the 30 odd years which have elapsed since the Coe and Clevenger paper is the recognition of the effect of the rakes on the thickening process. Bull and Darby2 noted this in 1926, and the extensive use of the "gluten type" thickener, in which the effect is magni-fied, bears witness to its importance. Comings3 further verified this effect of the rakes. As a matter of fact, a number of papers show an apparent regression from the Coe paper in that the area determinations are made on the basis of a single test from One concentration of solids. Coe and Clevenger amply demonstrated that this is unsafe, since the controlling zone may be one other than that of the feed dilution. Comings3 neatly demonstrated this without apparently realizing it. Of course there have been significant advances in the application of the operation to industry. Open tray thickeners were introduced to save area; balanced tray thickeners, washing thickeners, and multifeed clarifiers were developed with all of their special hydraulic and mechanical problems. Combinations of all kinds have been introduced, such as combination agitators and thickeners, combination flocculators and clarifiers, combination thickeners and filters. With the establishment of the operation on a firm engineering foundation, installation was facilitated and expansion proceeded. There are still problems, of course, functional as well as mechanical. Sometimes the moisture in the underflow obtained in practice is not as low as is expected on the basis of the test data. Sometimes the underflow is so "thick " that its discharge and subsequent handling requires special attention. Island formation plagues some operators. The use of the thickener as a surge basin and blending tank in the cement industry poses unusual problems. Design of rakes and the drive mechanism must be continually im-proved. Corrosion problems must he overcome. Power requirements for raking the settled solids occasionally is the controlling factor as it was in the case of the all American Canal desilting installation. Other similitude relationships and design problems come into the picture when we enter the field of clarification or nonline settlement. We have an energy dissipation problem in introducing the feed and any models must satisfy the Froude model relationships. Autoflocculation requires detention which involves the same similitude laws that we encounter in the compression zone. Approach to an Exact Science The next step beyond having control of the similitude relationships is to understand the why of these relationships right back up the line to first principles. The ultimate might be that, if given the mineralogical composition of the solids and their size distribution together with an analysis of the suspending liquid, we could calculate the entire thickening behavior of the system. Then we could say we had reduced the operation to an exact science. True it might be more trouble getting this basic analytical data than to make our empirical determinations for area and volume, and we would need an ENIAC to calculate the results, but that does not detract from the desirability of such understanding. Considerable work has been done by the chemical engineers with this end in view. Comings,3 Egolf,4 Work,5 Kam-mermeyer,6 Steinour,7 and others have studied the problem. The writer has no final answer to the thickening story but would like to propose a picture of the mechanics of the two phases of thickening which has been found useful in understanding the subject and which leads to some convenient relationship in treating the compression step and arriving at the compression depth.

Jan 1, 1950

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

By Gilbert Soler

THIS year's Chairman of the Iron and Steel Division is a noted member of a small and select group of practical scientists now working in this country and in Canada to improve the production and properties and to reduce the cost of super-quality carbon and alloy steels; he is one of those all-important leavening agents-a man with his feet always on the ground but capable of putting his head into the clouds on occasion-that are so necessary in applying science sensibly to the practical problems of steel production. He is equally at home in a discussion of the free energy of deoxidizing reactions or the entropy of the formation of stable sulphides, and in a consideration of the relative advantages of the basic-electric and the open-hearth furnace for the production of rimming steels in the Detroit area. Gilbert Soler was born of American parents in Havana, Cuba, just forty years ago. He graduated as a ceramic engineer from Ohio State University in 1930 and received a Master of Science degree a year later. In 1940 he received the degree of metallurgical engineer from the same institution.

Jan 1, 1948

By T. K. Perkins, L. R. Kern

A study of fluid mechanics, rupture of brittle materials and the theory of elastic deformation of rocks shows that, for a given formation, crack width is essentially controlled by fluid pressure drop in the fracture. Operating conditions which cause high pressure drop along the crack (such as high injection rate and viscous fluids) will result in relatively wide cracks. Conversely, operating conditions which cause low pressure drop (low injection rates and thin fluids) will result in relatively narrow cracks. Charts and equations have been derived which permit the estimation of fracture widths for a variety of flow conditions and for both horizontal and vertical fractures. INTRODUCTION There has been considerable speculation concerning the geometry of hydraulically created fractures in the earth's crust. One of the questions of practical importance is the width of fractures under dynamic conditions, i.e., while the fracture is being created and extended. Such width information could be used, for instance, to help estimate the area of a fracture generated under various conditions. Also, there has been a recent trend toward the use of large propping partiles.13, 15 Therefore is is desirable to know what factors can be varied in order to assure entry of the large particles into the fracture. There has been some work on fracture widths reported in the literature. In particular, there have been several Russian publications dealing with this sub-jeCt.1.31,3 These papers have dealt principally with the elastic theory and the application of this theory to hydraulic fractures. These studies have not led to an engineering method for estimating fracture widths under dynamic conditions. A recent paper3 has reviewed and summarized the Russian concepts. An earlier paper- from our laboratories also discussed the application of the elastic theory to hydraulic fractures. This first approach, based largely on photoelastic studies, has proved to be too simplified to accurately describe the fracturing process. However, these early thoughts have served as a guide during the development of more exact concepts. We would like to present in this paper our current concepts regarding fracture widths and some estimates of hydraulic fracture widths for several conditions. We believe that it is now possible to predict with fair accuracy the factors influencing fracture widths. Furthermore, the method of prediction has been reduced to a simple and convenient graphical or numerical calculation. CRACKS IN A BRITTLE, ELASTIC MATERIAL Many investigators2, 4, 30 have shown that competent rocks behave elastically over some range of stresses. Of course, if the tensile stress imposed upon a rock exceeds some limiting value, then the rock will fail in tension. In similar manner, there are some limiting shear stresses that can be imposed upon rocks. Hubbert and Willis11 have discussed the shear conditions which will lead to failure. Under moderate stress conditions (such as those likely to be encountered when hydraulically fracturing) and when stresses are rapidly applied, relatively, most rocks will fail in a brittle manner. Hence, for this discussion of hydraulic fractures in the earth's crust, we assume the rocks behave as brittle, elastic materials. Let us develop the discussion in the following way. (The following thoughts are applicable only to brittle materials.) 1. First we consider a brittle, elastic system. An energy balance will show the minimum pressure necessary to fracture rock, and from this pressure we calculate the minimum crack width resulting from extension of a hydraulic fracture. 2. Then we will show that, under ordinary fracturing conditions, fracture widths are appreciably greater than the minimum widths of extending fractures. In fact, we will find that crack width is controlled by fluid pressure drop in the fracture. 3. We will discuss pressure drops in fractures and resulting crack widths for various operating conditions and both vertical and horizontal fractures. 4. Finally, we will discuss the significance of these concepts, their relationship to fracturing pressures, etc. First, consider minimum fracture extension pressures. We can shed some light on this question by considering the theory proposed by Griffith7, 8 Yo explain the rupture of brittle, elastic materials. Griffith recognized that solid materials exhibit a surface energy8 (similar to surface tension in a liquid). The fundamental concept of the Griffith theory is that, when cracks spread without the application of external work (in the interior of an elastic medium which is stressed

The curve of Fig. 3 for pyrite requires modification. There 11% a range of pH values from 6.2 to 7.8 for which no cyanide is required to prevent contact. From 7.8 to 11.3 a small amount of cyanide is required, with a sharp maximum of 20 mg. per liter at pH=9.6. The mistake arose from considering too few solution compositions (17 were considered) in constructing the curve. Subsequent work with other collectors indicates that the corrected curve is typical for such systems; it illustrates the further development of the dip in the pyrite curve of Fig. 5.

Jan 1, 1938

By G. E. Agar, A. L. Mular

G. E. Agar (Manager, Minerals Processing Research, International Minerals & Chemical Corp., Skokie, III.) — The author notes a discrepancy between the parameters a and ß which are the slopes of the size distribution and energy-size modulus plots respectively. The reason for the discrepancy and the systematic decrease in the magnitude of a with grinding time is abundantly clear from the work of Fuerstenau8 on dry grinding. Fuerstenau shows very clearly in his Fig. 5 that at short retention times the parameter a is the same as that obtained by sizing over the complete size range. From this figure, it is obvious that sizing to only 400 mesh gave distribution curves similar to Mular's - that is, the slope apparently decreased systematically with increased grinding. As a consequence of the improper determination of a, the magnitude of ß given by Mular must be larger than the true value. In order to demonstrate this, the following Fig. 6 was taken from Mular's paper (his Fig. 1). Fuer-stenau's results show that we can approximate the correct value of K by drawing lines parallel to the short retention time curves through the 400-mesh

Jan 1, 1963

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.' Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by

By A. H. Hand

When considering the question of future demand for crude petroleum in California, one must first decide whether it is to be approached in the light of the definition of "demand" when used in economics; i.e., "The quantity of any commodity required or sought in the market," or in the light of markets developed to dispose of total supply. Therefore, is the California demand of future years to be predicated on a continuation of supplying markets developed following the surplus production commencing in 1922, or predicated on supplying what would be termed economic markets ? If the latter, what are economic markets ? Obviously, the Pacific Coast States and Canada, Alaska, Hawaii and probably the Pacific side of Central and South America, can be considered as normal markets for California petroleum products. While there have been small quantities of gasoline shipped into the PacSc Coast from East Texas, transportation costs, plus import taxes in the case of foreign oil, are a sufficient barrier to justify considering that these markets will be retained. But how about our participation in Atlantic and Pacific foreign and intercoastal markets? During the five years preceding 1931 California shipped substantial quantities of gasoline to the United Kingdom and to France, Germany and Italy. During recent years our business in European markets has been restricted to occasional shipments of gasoline and Kettleman crude. This loss of business is occasioned by the development of production in the Mid-Continent, principally East Texas, and in Iraq, Rumania, Venezuela and other closer producing areas, which makes it impossible at the prevailing crude-oil prices for California to be competitive in supplying any substantial portion of these markets. It is therefore apparent that under a stabilized price structure that will return the California producer a reasonable price for his oil, future Atlantic foreign -business will be restricted to occasional spot cargo sales. As to Pacific foreign shipments which, in addition to Central and South America, consist principally of shipments to Japan, China, Australia and New Zealand: A considerable portion of the business we had with Australia and New Zealand until four or five years ago is now being

Jan 1, 1937

By R. Adair, W. R. Hudspeth, W. T. McDaniel

ANEW method for concentrating the flake mica either from present washing plant tailings or from new feed has been developed. In this paper, flake mica refers to that which occurs in weathered granites, alaskites, pegmatites, and schists in a form too fine to be considered sheet mica. It ranges in size from 1 in. or more down to 200-mesh or finer and occurs with kaolin, quartz, and partially kaolinized feldspar. Scrap mica, a term often used indiscriminately to describe everything other than sheet mica, will be used to denote the waste product from sheet mica mines and fabricating plants. Both flake and scrap mica are used in the mica grinding plants to produce wet-ground or dry-ground mica, although some flake mica recovered from clay mining operations is fine enough to be marketed without grinding. Until 1930, ground mica was made almost entirely from scrap. From 1930 until 1935 a gradually increasing amount of flake mica was mined, and most of this was sold without grinding. A large percentage of this mica was recovered from clay washing plants. In this type of operation the recovery of any sheet mica was .of secondary importance and was considered a byproduct. North Carolina produces more flake mica than any other state, accounting for 73 pct of the total domestic production.' In the following review of current practice in jig plants, there is no intention to disparage these operations. Within the limitations under which they were built, they are examples of mechanical ingenuity. The term jig plant is a carryover from early practice since there are no jigs in operation at the present time. Current practice, as shown in Fig. 1, is based on successive stages of differential crushing with rolls followed by trommel screens to remove the more easily crushed gangue minerals. The oversize mica product then is usually dried, and passed through another set of dry rolls and a final screen to remove the remainder of the grit. This process is effective in recovering up to 50 pct of the mica in the original ore, the balance being lost in the screen undersize, usually —% in. Jigs and tables were at one time used to treat this screen undersize and were capable of recovering a part of the mica larger than about 60-mesh.V ine mica lost in these plants is normally washed away in streams and can be considered irrecoverable. There are ten or more washing plants in the North Carolina area that are losing approximately 50 pct of the mica in the feed. Since the three cooperating agencies, the Asheville Minerals Research Laboratory of North Carolina State College, the North Carolina Dept. of Conservation and Development, and the Tennessee Valley Authority, are concerned with conservation of minerals, they have investigated means for improving the efficiency of these mica plants. The mica industry has been cooperating fully with the laboratory to establish a more efficient method of recovery for flake mica. Choice of Methods The initial investigation was concentrated on finding a means of reducing the losses from plants now using the conventional flowsheet shown in Fig. 1. To accomplish this it would be necessary to collect the screen undersize products through the plant and remove from them the mica from Vs in. down to

Jan 1, 1952

The negative charges on diaphragms of quartz, tungstic oxides, stannic acid, acid dyestuffs, soaps, and glass have for a number of years been explained on the basis of chemical equilibria-a hydrogen ion or light metal ion passes into solution leaving the solid complex ion negatively charged. While there are a number of observations which indicate a proportionality between the ( potential and the streaming potential it should be recognized that all the experimental evidence thus far presented shows that if hydrogen ion concentration is kept at a constant value, electrokinetic phenomena are influenced by salts. The multivalent ions exert the greatest effect on the reduction of osmotic flow. In the interpretation of all electrokinetic data the assumption is made that the potential of the solid remains constant. That this is not true is evidenced by the values of ( potential for quartz in contact with conductivity water as reported by the several investigators and by the authors of this paper.

Sep 1, 1956

By C. H. Benedict

A 2000-ton ammonia leaching plant has been operated by the Calumet & Hecla Mining Co., at Lake Linden, Mich., continuously since February, 1917, except from April, 1921, to April, 1922, during the period of depression following the European war. A description of this plant has been published elsewhere.1 The present article describes the operation of the plant since 1917, together with the changes in the process that have been found to be advisable. In spite of the fact that this plant and that of the Kennecott Copper Co. are the only ones operating on a large scale, much experimental work is being done on ammonia leaching, as applied to oxidized ores, and it is to aid these and other investigators that this detailed account is given. For the benefit of those unfamiliar with the original article, the following short abstract is given, as an introduction to a more detailed account of the process and the reasons for present practice.

Jan 2, 1924

By R. Simon, D. J. Graue

This paper presents correlations for predicting the solu-lility, swelling and viscosity behavior of CO2-crude oil sys8i.m~. The correlations were developed from experimental data obtained by the authors. These data are also presented. The data were determined by measuring the properties of mixtures of CO, and nine different oils. Experiinental conditions covered a range of 100 to 250°F and pressures up to 2,300 psia. Properties predicted by the correlations have average deviations, expressed as per cent of experimental value, of 2 per cent for solubility, 0.5 per cent for swelling and 12 per cent for viscosity. INTRODUCTION Interest in CO2 injection as an oil recovery process has led to the development of performance prediction methods which can be applied to specific reservoirs.1 iS To use these performance prediction methods, it is necessary to know the solubility, swelling and viscosity properties of CO2-crude oil mixtures at reservoir conditions. Some information on these properties has appeared in the literature; however, this information did not cover the range of different oils and conditions needed to prepare generalized correlations for reservoir engineering purposes. Consequently, an experimental program was undertaken to collect the data needed. The data obtained and the correlations developed from the data are described in the following sections of this paper. SOLUBILITY OF CO2 IN CRUDE OILS CO2 solubility data in the literature come from six principal sources. The solubility prediction method of Welker and Dunlop3 is limited to 80F. The information in Ref. 4 is of two types: the first includes binary and ternary mixtures of CO, and light hydrocarbons (C1 to C6), and the second gives data for CO1 and heavy hydrocarbons for a temperature range of 40 to 90F. Ref. 5 contains a KCO2 chart for systems whose convergence pressure is 4,000 psia. The KCO2's are based mainly on CO2-natural gas mixtures. Poettmann's work covered CO2 solubility in one condensate and one crude oil6,7 Ja-coby and Rzasa measured CO? solubilities as a function of pressure and temperature for two natural gas-absorber oil mixtures and two natural gas-crude oil mixtures.'8 CO, concentration in these four systems was fixed at 5 mol per cent. The work reported in this paper extends CO, solubility data to a variety of different crude oil types in a temperature range from 110 to 250F and pressures up to 2,300 psia. The experimental procedure used by the authors to obtain the solubility data consisted of combining known amounts of pure CO, and crude oil in a visual cell at a fixed temperature and measuring the bubble point of the mixture. Measurements were made for a total of 40 different CO2-oil mixtures and the results are shown in Table 2. The mixtures included nine different oils (seven crude oils and two refined oils) whose properties are listed in Table 1. All nine oils had vapor pressures less than 1 atm at the experimental temperatures. Consequently, analysis of the bubble-point vapor showed a CO, concentration over 99 mol per cent. At no time during these experiments was a second, more dense, liquid phase observed. The solubility correlation which was developed from the data in Table 2 is presented in Figs. 1, 2 and 3. In these figures, solubility is expressed as xco2 the mol fraction of CO, in the CO2-oil mixture. Fig. 1 shows solubility as a function of CO2 fugacity6 and temperature. Fig. 2 shows the same solubility data expressed as a function of saturation pressure and temperature. The solubility shown in Figs. 1 and 2 is for an oil whose UOP characterization factor is 11.7. UOP characterization factors of crude oils can be determined from Ref. 10 if the viscosity and APT gravity of the oil are known. Fig. 3 gives the solubility correction factor for oils whose UOP characterization factors differ from 11.7. The solubility correlation in Figs. 1, 2 and 3 predicted

Jan 1, 1966

By S. B. Lement

THE nature of the carbides that form during the tempering of martensite is a subject of continuing controversy. The only direct methods of identification available are X-ray and electron diffraction. These methods are subject to several difficulties. Only a relatively few diffraction lines of appreciable intensity emanate from carbide phases that are formed at low tempering temperatures. Furthermore, some overlapping of carbide and matrix lines occurs. There is also the problem that numerous lines in the patterns of possible carbide phases that may be present have about the same d-spacings. Increasing the number of carbide lines and eliminating the matrix lines can be accomplished by extraction techniques. However, there is always the possibility that a change in carbide structure will occur as a result of removal from the parent matrix. Therefore, such techniques as electrolytic extraction and making extraction replicas should be checked by other methods. For identifying small amounts of carbide in a tempered martensitic matrix, electron diffraction carried out in reflection is more advantageous than X-ray diffraction. To properly prepare a specimen for reflection electron diffraction, an etchant that will selectively attack the matrix and thereby cause the carbide particles to stand in relief should be used. With an electron beam directed at a grazing angle to the specimen surface, the major contribution

Jan 1, 1960