Search Documents

By James Boyd

All mining and milling enterprises must be based on adequate ore reserves. Reserves must be established by physical exploration, and the orebody should be of sufficient size and grade to insure recovery of capital invested in mine purchase, development, and mill construction and to provide a reasonable profit. Determination of these economic factors is so complicated, and present costs of mine development and construction so great, that analysis can be made only by competent persons qualified by experience in this field. What rate for maximum efficiency? Unfortunately, even today mills are built before deposits have been adequately outlined, and there are rusting monuments to such folly in nearly every mining region. Also there is a tendency to be guided by the philosophy that "if a little is good, a lot is better," which leads to the conclusion that mining at a given rate and making so much per ton will yield a profit of so many dollars per day. Consequently, why not build a mill to treat twice as much per day and make twice as much money?

Jun 1, 1956

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of . Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director; The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: "The geographical districts to be considered by the Committee on Nominations shall he as follows, until otherwise ordered by the Board. District No. 1. New England, New York, and New Jersey, excepting New York City and district., which is provided for in the Constitution. (N. B.-New York City and district is designated District 0.) District No. 2. Pennsylvania. District No. 3. Ohio, Indiana, Illinois, Iowa, and Missouri. District No. 4. Minnesota, Wisconsin, and Michigan. District No. 5. Montana, North and South Dakota, Wyoming, Nebraska, Kansas, Washington, Oregon, Idaho, and Alaska. District No. 6. California and Nevada. District No. 7. Utah, Colorado, Arizona, and New Mexico. District No. 8. Louisiana and Texas. District No. 9. Other Southern States and District of Columbia. District No. 10. Mexico. District No. 11. Canada."

Jan 7, 1915

By William G. Fricke

MaCROSEGREGATION, as distinct from microseg-regation, is often inverse in nature. That is, the eu-tectic solute elements, which are expected to be con-

Jan 1, 1970

By A. F. Peterson, A. R. Eshbach

Much has been written to explain decreasing profits in American industry. Foreign competition, the attitude of government, rising tax burdens and increased labor costs have been blamed in turn. Whatever the cause, management in the mining industry, as elsewhere, is increasingly aware of diminishing profit margins. A mine operator is usually unable to do much about the causes of decreased profits, even if he knows what they are, but he can check the trend in part by cutting the cost of operation. To do this, he must know what his costs are, which of them are most significant and then go about reducing them in a systematic and logical manner.

Jan 10, 1962

By E. P. Pfleider

THE history of fundamental research in mining is not one of which the profession can be particularly proud. It has been one of the slowest industries in applying the fundamental sciences to the solution of many of its more difficult problems. True, many of the processes are not adaptable to laboratory techniques, and much of the work must, of necessity, be done in the field. It is for this reason that the mining executive seldom has been conscious of the value of research on a laboratory scale on problems pertaining strictly to mining. Most of them, however, fostered much testing in the allied fields of ore dressing and metallurgy.

Jan 7, 1951

By Chas. Kohl

ABOUT 1929 an engineer was engaged to organize a Safety Department, lay out an educational program, and achieve a reduction in accident frequency. Due to the large number of employees, about 12,000, and the distances between the various properties, it was a big undertaking. Most of the workmen are from the Sierra and for generations have been agricultural people, with little conception of modern tools and machinery, and to a large degree are illiterate. However, gratifying results have been obtained, as evidenced by the accident frequency curve during the sixteen-year period. Safety offices have been established in each of the six major properties, staffed by men who devote their entire efforts to inspections of working conditions and equipment, instructions as to safe methods, and investigations of accidents. The Corporation is a member of the Inter-American Safety Council, receiving their publications and literature, which serve to keep us up to date and informed on modern methods. Dissemination of this material is accomplished chiefly through word-of-mouth and bulletin boards. When it is found that the accident rate is increasing in a certain occupation, as for instance underground haulage or mine hoisting, the operators so engaged are assembled and given renewed instructions on the safety code pertaining to their work. Inter-camp competitions in accident avoidance are being conducted, with annual awards for that unit having the lowest severity rate for the year.

Jan 1, 1945

By M. B. Ramachandra Rao

THE spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° I7' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1-the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous micachlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, lithomargic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. METHOD OF SURVEY AND APPARATUS EMPLOYED The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1944

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By H. E. Gross

Recently, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 Ib. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 Ib. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rams holding a back pressure of 2900 Ib. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe²O³) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district. Laboratory Study of Heavy Muds To foster the use of the plentiful and extremely heavy mineral, galena, research has been done recently at the University of Oklahoma to determine the mud-making properties of this substance. For comparative

Jan 1, 1938

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing. committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee.

Jan 1, 1929

By A. E. Himebaugh

A SEMI-AUTOMATIC hoist has been installed at the 2966 station of the Copper Queen mine, since neither the bulk of supplies handled nor the number of men engaged in developing the 3100 level justifies the constant attendance of two cagers and two hoist operators. The connecting service shaft between the 2966 and 3100 levels is actually a two-compartment raise. Below the 2966 level the shaft is 7x13 ft-slightly oversize to permit downcast ventilation and provide space for the 16-conductor flexible control cable. The raise extends 52 ft above the 2966 level for a 3-ft diam head sheave. Another 3-ft sheave is mounted as an idler between the hoist and head sheave, eliminating the need for an inclined cableway. The main compartment serves as a cageway; the other compartment provides a manway and space for service lines. Since vertical travel is limited, rope speed is of minor importance.

Jan 5, 1958

By Will H. Coghill, Fred D. DeVaney, R. G. O’Meara

The size of ball mills in the ore-dressing industry has increased from about 4 ft. in each dimension to 10.5 ft. in diameter by 8 ft. in length. In the cement industry they are as long as 45 ft. Plainly the trend has been toward larger mills. The common belief is that the big mills economize in floor space and first cost, but the advantage with respect to friction has not been clearly defined. In the ball-mill studies at Rolla, Mo., laboratory mills as small as 2 by 2 ft. have been found as efficient in terms of the amount of grinding per unit of net power as mills 6 by 4 or 6 by 12 ft. Therefore, if supremacy can be claimed for the big mills, advantage must come from other sources. The advantage to be considered here is reduced loss by friction or dead load. In the study to determine whether big mills have relatively less loss by friction the commercial catalogs were used for fundamental figures. The dimensions and weights of Table 1 are taken from the catalogs (the last line gives data on a Rolla laboratory mill). The net power—that is, the power expended within the mill for grinding—is calculated by a new formula.' The assumed speeds are each at 70 per cent of their theoretical critical speeds, and the mills are loaded to the center with balls. In other words, they are assumed to be working under analogous conditions and are set for good grinding. In the last column the ratio B: A shows that the larger commercial mills are lighter per unit of net power than the smaller mills, and more of the motor output should therefore go into grinding. The laboratory mill seems to have some advantage over the larger mills; it would be expected to be light because it has no liners.

Jan 1, 1935

By H. Ries

THE term "clay" is applied usually to certain earthy rocks whose most prominent property is that of plasticity when wet. This permits them to be molded into almost any shape, which they retain when dry. Furthermore, they harden under fire. Clays contain hydrous aluminum silicates-the clay minerals-in appreciable amounts, but aside from this a number of other mineral grains, particularly quartz, may be present. Texturally clays are fine grained, and the so-called true clay particles are usually under 2µ in diameter. MINERALS IN CLAY Certain hydrous aluminum silicates that predominate in many clays are known as the clay minerals"." and are grouped by Kerr41 as follows: [ ] The kaolin group has been found to consist of a number of minerals with the same chemical composition but different crystalline structures .83 Kaolinite is commonly formed by the weathering of other mineral particles, particularly feldspar, but some deposits, like those in Cornwall, England,36 and others in the Washington-Idaho district, are thought by some to be of hydrothermal origin. Dickite and nacrite are thought to be due usually to waters of

Jan 1, 1949

By R. W. H. Atcherson

BLAST-FURNACE flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers acid more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of flue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained are shown in Table 1.

Jan 2, 1920

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic over- all manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation.

Jan 12, 1957

By Dan White

Stress measurements taken at Climax, El Teniente, Henderson, Lakeshore and Urad mines indicate that the deposits cited are generally subject to an inclined stress field that can be highly anisotropic. The horizontal stresses vary significantly between deposits and exceed the measured vertical stresses at Henderson and El Teniente mines. Experience at Henderson, Lakeshore and Urad mines is used to suggest a relationship between cavability and the premining stress. In poorly fractured, high strength rock masses, high stresses can assist the caving process. In well fractured, low strength rock masses, caving is ensured by breakage along fracture planes. The relationship between ground weight and the premining stress is also investigated. Ground weight problems appear to be most related to the competence of the ground rather than the magnitude of the premining stress as supported by experience at Climax and El Teniente mines. Recent developments in block caving favor the extraction of poorly fractured, high stressed rock. Accompanying the development of these deposits are new problems such as rock bursts. These pose particular problems to mine designers in that no experience currently exists in combatting rock burst problems at block caving mines.

Jan 1, 1984

By E. C. Robertson

Observations of faults in mines, at outcrops, and in the laboratory lead to the conclusion that the displacement d of a fault increases irregularly but monotonically with the thickness t of its associated fault gouge and breccia, not including adjacent undisplaced jointed rock. The general trend of data points has a slope d/t of about 100. (The correlation coefficient of a logarithmic regression line is r = 0.94.) The rather wide scatter of the points can be accounted for by inaccuracies in measurement of d and t, and by variation in the conditions at faulting of confining pressure, rock type, water pressure, and deformation history. Limestone is an exception to the relation. Until the data can be corrected and refined, the relation should be used only qualitatively for estimating displacement of ore bodies in mines. The suggested relation is based on observations of 48 steeply- dipping normal and reverse faults and nine small flat-dipping thrust faults, with displacement less than 5 km (3 miles). It does not apply to large strike-slip and low-angle overthrust faults because their large displacements are poorly determined and their breccia thicknesses are widely variable.

Jan 1, 1984