Search Documents

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.' Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References 'C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. 'E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

INTRODUCTION TO STATISTICS It is necessary now to digress from the direct study of appraisal techniques to consider an important tool for the mineral appraiser. Whenever a great deal of data have been accumulated, such as might be gained through the sampling process discussed in the preceding chapter, the application of statistical methods should be considered. Statistical methods are used for descriptive purposes and for the organization and summarization of quantitative or numerical data. Descriptive statistics covers the tabulation of data, its presentation in graphical or pictorial form, and the calculation of its several descriptive measures. It is not the intent of the brief summary of statistics that will be outlined hereafter to cover the total breadth and scope of mathematical statistics. It is the intent of this and the following chapters to review a few of the statistical concepts that have the most direct bearing upon the problems involved in mineral evaluation. Should the reader desire to go more fully into statistical theory and mathematics, numerous texts and publications are available.

Jan 1, 1980

By D. S. G. Hanson

The Flin Flon Mine has been in production for over fifty years, and current mining is dependent on pillar and remnant recovery. One of the last major blocks of ore, and an important economic entity to the Mine, is the North Main Shaft Pillar. A rock mechanics program was initiated through under' ground instrumentation and other subsequent analyses, to establish the degree of instability as min¬ing progressed. Several studies have been and will be undertaken to evaluate the general stability, and possibly improve the chances of stability during pillar recovery. The North Main Shaft Pillar is immediately bounded by cemented cut and fill supporting rib stopes which inturn are bounded by slag and waste filled stopes. The min¬ing method involves a modified longhole open stoping and slag fil¬ling sequence for each mining block in a general mining upwards scheme.

Jan 1, 1983

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

By O. H. Eschholz

THE electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulphuric acid mists, it has been extended until at present there is practically no fume carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, -by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may he selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained front the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct current, requiring: (a.) Source of alternating-current energy. (b) Means of transforming from tow voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids.

Jan 8, 1918

By Leonard E. Wood, Yeghishe M. Avedissian

Knowledge of the basic properties of rocks-strength, structure, and permeability-is prerequisite for the success of foundation work for masonry dams, large bridge piers, and tunneling as well as for excavation in rock and special underground construction. Strength of engineering materials depends upon texture and structure as well as the environmental conditions to which they have been subjected. Failure in its widest sense implies the transition of a material from elastic to plastic state (yield strength), from continuous to discontinuous state (rupture strength). The compressive strength of a material such as rock is the stress at which a sample, loaded and unconfined at the sides, fails by rupture. Some of the external factors that control strength of rocks are the nature and type of stress, whether uniaxial or triaxial, compression, tension, or torsion. Another important factor is the rate of stressing-whether constant, impact, or gradually increasing. Of the internal factors, the effect of texture upon strength is obvious. Generally, fine-grained rocks have higher compressive strength than coarse-grained prototypes. Among metamorphic and igneous rocks those with better and higher degree of interlocking of their crystals are generally stronger than the ones with poor or lower degree of interlocking. In sedimentary rocks, the degree and type of cementation has a great influence upon their strength. Structurally, the existence of fissures, cracks, and seams of argillaceous or organic materials in a rock specimen will greatly reduce its strength. Because most rocks are characterized by bedding planes, laminations, or foliations, they are anisotropic in their physical properties and hence compressive strength depends on the orientation of the bedding planes to

Jan 1, 1972

For the first time in its history the Institute will hold a meeting in the State of Arizona. A few years ago Arizona stood third in the copper-producing districts of the United States. Since that time, with the development of porphyry mines, the output has gone up with great rapidity until it not only is the leading district, but its output at the present tune is at the rate of nearly double the Montana output; which now stands second in the list. In connection with this development, most interesting departures have been made in methods of mining, concentration and smelting. Principles of mining and metallurgy of the greatest interest will be covered by papers which will appear in the Bulletin and be presented at Technical Sessions, while ample opportunity 'will ,be- afforded for those who go to the meeting to see all the points of interest to them. In addition, members will be well rewarded by the marvelous natural features to be seen on the trip, including the petrified forests, the cliff dwellings on the Apache Trail and the Grand Canyon of Arizona. It is planned to start the special train from New York, but members and guests may join the special at other points en route as indicated by the following schedule: ITINERARY Thursday; September 14th, Lv New York Grand Central Terminal 5.30 p.m. Dinner in dining car, a la carte

Jan 9, 1916

By J. G. Koenigsberger

The electrical specific resistance of rocks in the field is measured by sending a current through a medium of great volume, compared to the electrodes, whose resistivity should be measured. The whole resistance can be determined by the Wheatstone bridge and the specific resistance calculated by a well-known formula. The resistivity of some rocks in place in Germany and in Switzerland is given; first, of a rock near the surface, and especially near electrodes. Practical applications are made in the determination: (1) of the continuity of a conducting orebody; (2) of the surface ares of an orebody; (3) in the detection of a water-bearing fault in a salt mine. Preliminary 'observations are described: (1) on the influence of the depth of ground-water table; (2) on the detection of gas under high pressure in coal seams. The observations in this paper of the electrical resistivity of rocks and soil in place are along the lines of the very interesting method and results of the Messrs. Gish, Rooney, Hotchkiss and Fisher. 1,2 All the work described has been done since 1920. Method Used The very simple method consists in the application to the rock of two plane circular electrodes of iron or brass of a suitable diameter, with the aid of a contact substance, and in measuring the resistivity in a Wheatstone bridge with alternating current of 100 to 400 Hertz frequency per sec.). The general formula is known to be R= R0 +d/4(1/a+1/b-1.7/l+0.8(a+b)/l2) (1)

Jan 1, 1929

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By T. L. Chu, G. A. Gruber

Silica films hare been rleposited 011 silicon substmtes at 400° to 600°C by a chemical-transport technique using hydrogen fluoride as the transport agent ill a closed system. This transport takes place from a source materia1 1071: temperature to substrates at higher temperatures, as indicated by the thermochemistry of the transport reaction. The experimental variables of- the transport process, such as the substrate temperature, the pressure pi the transport agent, and so forth, have been studied. The rate -determining step of the transport process appears to he the ),ale of chemical reaction in the source region. The transported films are similar to thermally grown silica films in physical proper-ties with the exception of 'some what higher dissolrrtion rates. SILICA films deposited on suitable substrates serve many purposes in electronic devices. They are used for the fabrication of tunneling devices, the surface passivation of devices, and the shielding of devices from nuclear radiation: and as selective masks against the diffusion of specific impurities into semiconductors. Doped silica films can also be used as sources for the diffusion of impurities into semiconductors. Several oxidation and deposition techniques for the preparation of silica films have been developed to meet the requirements of these applications. The therma1 oxidation of silicon by oxygen or steam at temperatures above 900 C is commonly used in silicon technology. The deposition techniques are perhaps more advantageous since they usually require lower temperatures and are not limited to silicon substrates. Silica films have been deposited on silicon and other substrates by reactive sputtering and chemical reactions. The sputtering of silicon in an oxygen atmosphere is capable of depositing good-quality silica films on silicon' and gallium arenide. Many chemical reactions are known to yield silica at room temperature or higher. These reactions may involve intermediate steps. However, the final step yielding silica should take place predominately on the substrate surface in order to produce adherent films. When silica is formed in the gas phase by volume reactions, no adherent deposit can be obtained. Generally, the experimental conditions of a reaction can be varied so that the surface reaction predominates over the volume reaction. The chemical reactions which have been used successfully for the deposition of silica films are briefly as follows. The pyrolysis of alkoxysilanes in an inert atmosphere or under reduced pressure has been employed to deposit silica films on germanium3 and silicon4 at 650" to 750°C in a flow system. The deposition of silica films from alkoxysilanes has also been achieved at nearly room temperature by a low-pressure plasma. Device quality silica films have been deposited on germanium and gallium arsenide by the deposition of an amorphous thin silicon film followed by oxidation at 600" to 700" . Silica films for high-temperature capacitors have been produced by the hydrolysis of silicon tetrabromide at 950°C in argon and hydrogen atmospheres.7 We have developed a chemical-transport technique for the deposition of silica films on semiconductor substrates at relatively low temperatures. The thermochemistry of the transport reaction, the experimental variables of the transport process, and the properties of the transported silica films are described in this paper. THERMOCHEMICAL CONSDERATIONS The transport of solid substances by chemical reactions in the presence of a temperature gradient has been used for the preparation of films and crystals of many electronic materials. In this technique, a gaseous reagent is chosen so that it reacts reversibly with the solid substance under consideration to form volatile products. Since the equilibrium constants of most reactions are temperature-dependent, the transport of these products to regions of suitable temperature in the reaction system would cause the reverse reaction to take place. depositing the original solid. When the equilibrium is shifted toward the formation of the solid as the temperature is decreased, the solid is transported from a high-temperature zone to a lower-temperature region, and vice versa. This chemical-transport technique can be carried out in a closed or gas-flow system. In a closed system, chemical equilibrium is presumably established in the different temperature regions of the system, and the transport agent regenerated in the deposition region repeats the transport process in a cyclic manner. The local chemical equilibrium may not be approached in a flow system: however, this system offers a greater degree of flexibility. Silica reacts reversibly with hydrogen fluoride and this reaction was chosen for the transport process. The over-all reaction between silica and hydrogen fluoride may be written as: SiO2(s) + 4HF(g-) = SiF4Ur) + 2H2O(^)

Jan 1, 1965

By J. W. Turrentine

SECONDARY fertilizer minerals include borax, gypsum and sulphur and such compounds as the sulphates of copper, magnesium, manganese and zinc; also the carbonate and oxide of magnesium. Potash, phosphates and nitrogen are generally considered to be primary fertilizer materials. The growing plant, under the average conditions of growth, is able to get from the soil the mineral elements required for the completion of its life cycle. The elements taken up are numerous and the vital functions of some of them yet remain to be determined. However, in the commercial growing of the plant (farming) something much more than the mere completion of a life cycle is required. There the maxi- mum possible growth of plant or yield of seed or fruit are the objective and for that objective the average soil is deficient in some elements, and additions from artificial sources are desirable. Commercial fertilizers (15,000,000 tons in 1946) are designed to supply those deficiencies. Long experience has taught that nitrogen, phosphorus, and potassium are the elements most apt to be required and in a greater degree, and to supply them is the-basic function of the fertilizer industry. Thus nitrogen, phosphate, and potash are designated as the major plant-food materials. But other mineral crop nutrients may likewise be deficient in varying degrees as determined by diagnostic techniques, soil tests, plant analysis and foliar symptoms,3 calling for their addition from artificial sources if maximum crop yields are to be obtained. Because used in lesser amounts and frequently in relatively minute amounts as compared with the major three, they are designated either as "minor elements," or, if used in larger amounts, as "secondary elements." Thus, included under the two designations, in alphabetical order, are: borax; copper sulphate; magnesium carbonate, oxide and sulphate; manganese sulphate, and zinc sulphate. Obviously, the sulphates of the metals copper, manganese, and zinc cannot be considered as "industrial rocks," but they are given brief mention for whatever interest may pertain there to.

Jan 1, 1949

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By W. B. Hall, Joy D. Lewis

Mine-run ore is received at Vitro in gondola cars and fed directly to a Cedar Rapids impact crusher. Following screening, the undersize travels through a recently installed three-stage sampling plant where successive cuts are executed by conventional Geary-Jennings type cutters to produce a final sample of 1 lb per ton of raw ore fed. Crushed ore is transported to one of three storage silos or to stockpile, depending upon grade and type of amen- ability. This permits the blending of a mill feed with some degree of consistency. Final grinding is accomplished in one of two closed circuit ball mill-classifier systems allowing simultaneous processing of two basic types of ores. High acid consumers may be leached separately in the required environment. Part of the free acid remaining can then be utilized by an ore stream entering later whose component ores require much less free acid for leaching.

Jan 11, 1958

By Charles L. Bauer

WHEN a single crystal is annealed following plastic deformation recrystallization usually occurs rather than polygonization. Consequently, re-crystallization has received the overwhelming amount of attention albeit the intrinsic mechanisms by which dislocations rearrange and annihilate one another are just as well revealed by crystal polygonization. It is the purpose of this note to demonstrate the usefulness of studying the polygonization process by means of an etch-pit technique in sodium chloride. Sodium chloride deforms easily (the slip system is of the [110], (110) type), readily cleaves on (100) planes, and can be chemically etched so as to reveal the intersection of dislocations with a free surface. Thus it is possible to observe the distribution of dislocations after a crystal has undergone a specific deformation and annealing cycle. Various phases of the polygonization process

Jan 1, 1965

By Oscar Kuchs

IN January and February of the current year, at the Tooele plant of the International Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast- furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of reverberatory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it was planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary: to install a bag house, a fan, and the necessary flues to complete the equipment.

Jan 7, 1914

By D. J. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers. 1.2.3.1 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper .2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and nonferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

Jan 1, 1928

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By Morris A. Dodd

The nodulizing process described converts finely divided zinc calcine into a dense purified nodule. These zinc nodules are suitable for direct use in zinc reduction furnaces, especially the horizontal retort type, for the production of metal or American process zinc oxide furnaces for producing lead free zinc oxide. The basic reactions are carried out in a rotary kiln fired with fuel oil or natural gas. The combustion gases travel countercurrent to the flow of the zinc bearing material. Volatile impurities are carried out of the kiln with the combustion gases and a small portion of the finely divided feed material. The gases are cooled and the larger solid particles are separated from the stream before the resultant fume is collected in a conventional cloth filter baghouse. The fume collected can be further processed by conventional wet processes for the recovery of metallic values such as lead and cadmium. In order to nodulize the calcine properly it is elevated to a point of incipient fusion. The agglomerated material falling from the kiln is cooled and then sized by passing through a screening and crushing system consisting of a jaw crusher and a roll crusher in closed circuit with a vibrating screen.

Jan 1, 1970

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942