Search Documents

By Herbert H. Uhlig

ALTHOUGH the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldlo summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.15 per cent carbon. He noted: From these comparisons it will be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable. Ib His data showed that alloys containing 4 to 10 per cent manganese water-quenched from 1000°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 870°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loringa reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 540°C. (1000°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.15 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <0.001 per cent P). In this paper it is shown that of the low- carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from 1000°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By W. H. Reck

Increasing use of flotation in modern beneficiation has resulted in a variety of froth handling methods. Froth must be handled mechanically to maintain common floor elevation, because pure gravity flow, stage to stage, makes for multiple level machine installations with higher first cost and less convenient operation. Bucket Elevator--Froth is collected by launder and goes to the feed entry of the elevator, below the floor. The bucket goes to the next treatment stage by gravity flow. The outstanding advantage is high efficiency of conveyance.

Jan 5, 1955

By Orville R. Lyons, A. C. Richardson

Operating data is presented for a Bird centrifuge used to dewater coal treated at one preparation plant. The data include: (1 ) percentages of solids in centrifuge feed, cake, and effluent and the plant circulating water for a period of four consecutive operating shifts, and (2) screen-sizing data for a number of centrifuge feed, cake; effluent, and combined cake-effluent samples. An evaluation is included of the relationships between fine solids in the centrifuge feed and the total moisture content of the centrifuge cake.

Jan 3, 1950

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Y. Okahara, I. Iwasaki

Chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganous oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were dificult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexities of the reactions, and the possible mechanisms were discussed. Then three manganif-erous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides. One of the unsolved problems challenging Minnesota&apos;s mining industry is the development of an economic process to utilize the manganiferous iron ores of the Cuyuna Range. Although these ores constitute one of the major domestic reserves of manganese (estimated at 432 million tons&apos;), their grade is too low for them to be mined solely for manganese. The nearly exclusive dependence of the U.S. steelmaking industry on foreign manganese ores has stimulated research over the years in treating the low-grade Cuyuna ores. As a result, a number of processes have been proposed.&apos;-&apos; Among these processes is chlorination. Chlorination is the high-temperature conversion of metallic oxides to chlorides by either chlorine or hydrogen chloride gas, or by solid chlorides of sodium, calcium, or magnesium. The metallic chlorides are then recovered by either vaporization or leaching. Although chlorination is an old art, it has become popular in recent years for the recovery of such new metals as titanium, zirconium, and niobium; for the removal of impurities like copper, lead, and zinc from pyrite cinder for ironmaking raw materials;&apos; and for the segregation roasting of coppera and nickel&apos; ores. The chlorination processes proposed for manganifer-ous iron ores have been relatively few (hydrogen chloride chloridization-leaching, hydrogen chloride and calcium chloride chloridization-volatilization,&apos; and chlo-rination-selective condensation6), due presumably to the economics and to the corrosion problems involved. However, the successful application of chlorination processes to other ores will undoubtedly contribute to technological advancements in the chlorination of man-

Jan 1, 1971

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge&apos;s method8 for measuring two-phase relative permeability. Although Sarem&apos;s method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem&apos;s assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem&apos;s.

By E. D. Gardner

The tide of increasing demand for metals turned during early 1949, with resultant lower prices. The production of the principal metals was less than in 1948. The problem of high unit costs, however, was held over from 1948. With the lower prices for metals, greater efforts are being made to reduce operating costs. The labor supply was adequate during the latter half of the year in most districts. The force has been reduced at most mines; some mines were idle during part of the year because of strikes, and others ceased operations on their own account. In the main, labor efficiency increased during the year in underground metal mines. Efforts are being made generally to improve labor relations. Green men hired in the time of the scarcity of skilled miners are becoming better trained. The supervisory personnel of most mines is cost conscious, and the planning of operations has been improved. Overhead costs are being scrutinized. The trend toward mechanization underground continued strong. Mining technology rapidly is becoming a problem of handling materials. Surface miners, underground miners and miners of metals, nonmetallics, and coal can learn much Gardner from each other. A mine, however, may become overmechanized. The capital charges against new equipment may exceed the saving in labor costs where sufficient daily tonnage is not handled.

Jan 1, 1950

By L. C. Morganroth

Discussion of the paper of L. C. MORGANROTH, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 475 to 481. DAVID B. REGER, Morgantown, W. Va.-I notice in the third paragraph of the first page of the paper, that in mentioning the clays of the Pottsville series, the author says: "The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible."). If the author wishes to confine himself to the fire clays of Pennsylvania, as the title seems to indicate, I have nothing to say, but if he wishes to include a discussion on fire clays of the adjoining States which the. subsequent paragraphs of his paper seem to indicate, then I wish to call attention to the fact that there are large and extensive deposits of fire clay in the Allegheny series, immediately overlying the Pottsville in the northern counties of West Virginia. These fire clays have been studied carefully, and described in several reports of the West Virginia Geological Survey, first in the report on Ohio, Brooke, and Hancock Counties, in the northern part of the State; described later ,in the report on Monongalia, Marion, and Taylor Counties, and in the report on Preston County, which followed. In these latter counties (Monongalia, Marion, Taylor, and Preston) there are some beds of fine fire clay, varying in thickness from 6 to 10 or 12 ft., with a content of only 2 or 3 per cent. of fluxing ingredients, and these are of the typical Savage Mountain appearance and also have the typical Savage Mountain fracture. They have been prospected, but not mined a great deal. Several of them have been tested in blast furnaces and furnaces for other purposes, in glass-manufacturing plants, also for firebrick, arid have been found to be very good. They are simply awaiting development, and I merely want to call attention to the fact that there are plenty of them in the Allegheny series still above the Pottsville in West Virginia. There are two or three valuable seams which I have seen in person and have had analyzed in our laboratory.

Jan 5, 1916

By D. W. Brunton

The erection of large metallurgical establishments for the treatment of gold, silver, copper, and lead-ores, at railroad arid topographical centers, where fuel and fluxes, together with proper oremixtures, can be cheaply and constantly obtained at all seasons of the year, has led to the very general introduction of a system of ore-handling known as "public sampling." By this system the ore, instead of being shipped direct to the mill or smelter, is sent to a public sampler, where it is crushed and sampled. Guaranteed samples are sent to the different metallurgical establishments, and the ore is then sold to the highest bidder. Though differing in many respects from the English system of "ticketing," the underlying principle is nearly the same, while the greater rapidity with which a lot of ore can be disposed of renders

Jan 1, 1885

By Frank R. Milliken

Before the rather sudden economic downturn in recent months, shortages of materials were painfully felt throughout the US. The current recession has provided a temporary relief here and there-but energy fuels and a number of staples such as sugar are still in short supply. This is an unsolved and fundamental problem that will haunt us again as the economy turns up. There is an awareness that the nation faces a widening supply gap in many of its most basic materials-from asbestos to tungsten-as evidenced by recent studies and government reports, and by the Secretary of the Interior&apos;s annual warnings about the mounting seriousness of the problem.

Jan 3, 1975

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By Oscar M. Kucus

In January and February of the current year, at the Tooele plant of the hternational Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of rever-beratory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it mas planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary to install a bag house, a fan, and the necessary flues to complete the equipment. The bag house constructed has a bag-cloth filtering area of 136,000 sq. ft., provided by 960 fume bags, 18 in. in diameter by 30 ft. in length. A No. 20 Sirocco fan of 180,000 cu. ft. capacity delivers the gases from

Jan 1, 1915

By Dorsey Hager

North Central Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.), has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at least $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per day; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha.), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft. At present, the lease brokers and speculators, and only a handful of oil men, have made any money. More fields must be developed, and it is more particularly with these possibilities that this paper deals. Lack of water for drilling purposes has undoubtedly held back development so far this year; this part of Texas has had a drouth for two years and there is an actual scarcity of water. Geological investigations so far undertaken cover nearly all the area outlined, and while pakt of the

Jan 1, 1920

By AIME AIME

SIR HENRY CORT HAROLD CARPENTER, great-great-grandson of Henry Cort, famous as the initiator of iron puddling some 150 years ago, carries on the tradition of an illustrious name. Newest of those elected to the Institute&apos;s roster of Honorary Members, Sir Harold is distinguished for his achievements in the field of metallurgy as an investigator, teacher, administrator, organizer, and director of research. His interests in research have been in both the ferrous and non-ferrous fields. His name is particularly honored in its association with the establishment of fundamental con¬stants and of critical ranges of iron and iron alloys, and with original and fundamental studies of the preparation and properties of metal single crystals.

Jan 1, 1938

The Library of the above-named Societies is open from 9 A.M to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 6, 1918

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 11, 1918

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will he sent more promptly and in more usable shape.

Jan 9, 1917

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1918