Search Documents

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By William P. Blake

THE importance to the growing steel industry of the United States of a domestic supply of ferro-manganese or "spiegel" of a high grade, induces me to bring to your notice some details of the method by which a superior article is produced in the Austro-Hungarian Empire. At Reschitza, Hungary, and probably at Laibach also (the Krainische Industrie Gesellschaft), ferro-manganese is made in a blast-furnace, with charcoal as fuel, and limestone as the flux. The ore is a ferruginous mixture, containing about 37 per cent. of sesquioxide of manganese. It is silicious, and somewhat resembles, in its appearance, the manganese ore from Red Island, in the Bay of San Francisco, California. It contains about 29 per cent. of silica and some alumina, shown by the subjoined analysis

Jan 1, 1876

By G. Stuart Jenkins

Conditions at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, hut to drive a slope on an inclination of 17½°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly. Sinking the Slope It was decided, in sinking the slope, to make an opencut until rock was reached, which was some 65 ft. below the surface, and then to drive the slope through an inclined tunnel from that point. In making the open-cut, the schedule called for the removal of about 25,000 cu. yd. of clay, holding the banks on an inclination of one and a half to one, the thought being to make this cut in a minimum of time, put in a reinforced concrete slope, and then back-fill. Difficulty was experienced because the clay was of a sort that was called "subsiding base" material by contractors visiting the job. In other words, a "squeeze" occurred, the pressure causing the floor of the cut to move up just as it does in many mines where the coal is underlain by thick fire clay and inadequate pillars have been left. It was necessary to move the waste banks back from the edge of the cut 700 or 800 ft., and even then the floor could not be controlled, the result being that almost 100,000 cu. yd. of clay was handled before the rock was reached. A concrete slope was then rapidly constructed, using 95 tons of special-shaped reinforcing iron. The floor of this slope was made 30 in. thick at the bottom, and 17 in. thick at the top, the sidewalls being 18 in.

Jan 1, 1940

By G. Stuart Jenkins

Conditions at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, hut to drive a slope on an inclination of 17½°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly. Sinking the Slope It was decided, in sinking the slope, to make an opencut until rock was reached, which was some 65 ft. below the surface, and then to drive the slope through an inclined tunnel from that point. In making the open-cut, the schedule called for the removal of about 25,000 cu. yd. of clay, holding the banks on an inclination of one and a half to one, the thought being to make this cut in a minimum of time, put in a reinforced concrete slope, and then back-fill. Difficulty was experienced because the clay was of a sort that was called "subsiding base" material by contractors visiting the job. In other words, a "squeeze" occurred, the pressure causing the floor of the cut to move up just as it does in many mines where the coal is underlain by thick fire clay and inadequate pillars have been left. It was necessary to move the waste banks back from the edge of the cut 700 or 800 ft., and even then the floor could not be controlled, the result being that almost 100,000 cu. yd. of clay was handled before the rock was reached. A concrete slope was then rapidly constructed, using 95 tons of special-shaped reinforcing iron. The floor of this slope was made 30 in. thick at the bottom, and 17 in. thick at the top, the sidewalls being 18 in.

Jan 1, 1940

By Benjamin F. Tillson

Although portable fire extinguishers are valuable for fires in an incipient stage, some medium that will dissipate a large amount of heat is needed to fight a fire in mine timbers, because of the size to which the fire will probably have grown before it is discovered. Scaling off, or otherwise smothering such a fire with gases that will not support combustion, is often ineffective for the residual heat will cause reignition when the area is opened and fresh air reaches the hot charred timber. The most effective ways of fighting mine fires, therefore, are to drown and cool the hot zone with water, and to "load out" the partly burned material. Either of these methods requires a direct attack of water ; upon the inflamed material; therefore, every mine containing a large ' quantity of timber or other combustible should be as completely equipped with a fire-hydrant system as it is with compressed-air mains. Mine managers may object to the expenditure, especially if they have not suffered from mine fires. The cost of such preventative measures, however, is only a small portion of the possible losses, and the water pipes can be used for other purposes, which will pay the carrying charges. They can supply water to the rock drills, which will encourage more wet drilling with hollow-drill steel, for the trouble and expense of packing water to individual tanks at the drills will be removed. The carbon-tetrachloride hand extinguishers seem to have no place in mining except for fires that start in electrical equipment. They give off noxious gas, which may prove poisonous in confined quarters; and as it is heavier than air it is of no value for smothering fires overhead or in side timbers and would be dissipated by a good ventilating draft. The old soda-acid extinguisher or the more modern "foam" types ' are preferable. The former probably does not rely for its efficacy on the carbon dioxide generated but on the smothering and cooling effect of the water and the trajectory of stream that may be obtained because of the gas pressure developed. The production of a foam having a tough film to smother a fire, even on overhead surfaces, with the added

Jan 1, 1923

By Benjamin F. Tillson

Although portable fire extinguishers are valuable for fires in an incipient stage, some medium that will dissipate a large amount of heat is needed to fight a fire in mine timbers, because of the size to which the fire will probably have grown before it is discovered. Scaling off, or otherwise smothering such a fire with gases that will not support combustion, is often ineffective for the residual heat will cause reignition when the area is opened and fresh air reaches the hot charred timber. The most effective ways of fighting mine fires, therefore, are to drown and cool the hot zone with water, and to "load out" the partly burned material. Either of these methods requires a direct attack of water ; upon the inflamed material; therefore, every mine containing a large ' quantity of timber or other combustible should be as completely equipped with a fire-hydrant system as it is with compressed-air mains. Mine managers may object to the expenditure, especially if they have not suffered from mine fires. The cost of such preventative measures, however, is only a small portion of the possible losses, and the water pipes can be used for other purposes, which will pay the carrying charges. They can supply water to the rock drills, which will encourage more wet drilling with hollow-drill steel, for the trouble and expense of packing water to individual tanks at the drills will be removed. The carbon-tetrachloride hand extinguishers seem to have no place in mining except for fires that start in electrical equipment. They give off noxious gas, which may prove poisonous in confined quarters; and as it is heavier than air it is of no value for smothering fires overhead or in side timbers and would be dissipated by a good ventilating draft. The old soda-acid extinguisher or the more modern "foam" types ' are preferable. The former probably does not rely for its efficacy on the carbon dioxide generated but on the smothering and cooling effect of the water and the trajectory of stream that may be obtained because of the gas pressure developed. The production of a foam having a tough film to smother a fire, even on overhead surfaces, with the added

Jan 1, 1923

By AIME AIME

JAMES TERRY DUCE is still on the sunny side of fifty, having been born on Dec. 30, 1892 in Worcester, England. Early in life he came to the United States, however, and graduated from the University of Colorado in 1915 .as a geologist. Thereafter for a few years he was with the Colorado State Geological Survey and Bureau of Mines, also doing a bit of teaching at his alma mater and at Washington University, St. Louis. Towards the end of the World War he was with the chemical warfare section of the U. S. Army. Beginning in 1919, he spent 21 years as geologist in various capacities for The Texas Corporation, for a time

Jan 1, 1941

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By Calvin Pierson, R. S. Dean, E. P. Barrett

Wrought iron and steel have been prepared from limonite, hematite, and magnetite ores by gaseous reduction, compacting and squeezing the resulting product at high temperature and finally melting the wrought iron so formed. The structure, analyses, mechanical and magnetic properties of the products are given. It is found that the structure of iron ores is best studied by subjecting them to gaseous reduction and using metallographic technique on the resulting sponge iron. In this way the cell structure of iron ore is clearly shown. The wrought iron made by heating compacted sponge iron to 1450" C., and forging, shows a cell structure inherited from the ore. This cell structure is further preserved in melting and casting the wrought iron. The probable relation of the properties of the materials to this inherited cell structure is discussed.

Jan 1, 1935

By Calvin Pierson, R. S. Dean, E. P. Barrett

Wrought iron and steel have been prepared from limonite, hematite, and magnetite ores by gaseous reduction, compacting and squeezing the resulting product at high temperature and finally melting the wrought iron so formed. The structure, analyses, mechanical and magnetic properties of the products are given. It is found that the structure of iron ores is best studied by subjecting them to gaseous reduction and using metallographic technique on the resulting sponge iron. In this way the cell structure of iron ore is clearly shown. The wrought iron made by heating compacted sponge iron to 1450" C., and forging, shows a cell structure inherited from the ore. This cell structure is further preserved in melting and casting the wrought iron. The probable relation of the properties of the materials to this inherited cell structure is discussed.

Jan 1, 1935

By Reginald S. Dean

THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these 'requirements. Other hereto-fore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filterable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and C02, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores; including Three Kids, Artillery Peak, Cuyuna, and Chamberlain; as repre-

Jan 1, 1952

By John Chipman

RECENT developments in iron alloys containing nitrogen have indi-cated that this element may exert a considerable influence on the proper-ties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Jurich,1 Sieverts,2 Martin,3 and Iwasé4 and the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss5 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By AIME AIME

THE 1941 fall meeting of the Iron and Steel and the Institute- of Metal, Division held at the Ritz-Carlton Hotel, Philadelphia, during the first three days (Oct. 20-22) of the National Metal Congress was well attended as usual, and the seven technical sessions and the joint round table on order-disorder transformations were this year of considerably more than routine interest. Despite unseasonably warm weather, a scarcity of hotels (there were rumors, apparently well-founded, that , some of the metal man attending the Congress had to stay in tourist camp), and a multiplicity of technical and other ions of the co-operating societies that gave the Congress this year the general air of a three-ring circus the A.I.M.E. sessions attracted audiences that ragged from seventy or eighty up to 350

Jan 1, 1941

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320' C. Because of the size of our induction coil we are limited to this temperature, although it 'would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700' to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937

By Hans Lundberg

IN last year's report on the progress of geophysics, the airborne magnetometer was the featured new development. At that time only a relatively small number of surveys had been made. During 1947, the airborne magnetometer was used in making many surveys and is again one of the high lights of the year in geophysics. This report is mainly concerned with geophysics as applied to the search for minerals exclusive of petroleum. In 194,5 and 1946, the use of the magnetic method reached a peak, partly because of an active period of prospecting brought on by an active mining market, particularly in Canada.

Jan 1, 1948

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By Greenleaf W. Pickard

The Parral mining district is located in the southern part of the state of Chihuahua in north-central Mexico, in the border area of the physiographic provinces of the Mesa Central and the Sierra Madre Occidental, at an average elevation of 1700 meters. This is one of the most highly productive lead-zinc districts of Mexico. The principal operating units are the Prieta, Santa Barbara and San Francisco mines. The Santa Barbara-San Francisco del Oro area is located 25 kilometers to the southwest of the Prieta mine. It has a system of generally narrow veins in fault zones, entirely in the shale series. The Santa Barbara veins follow long, persistent fractures, while the San Francisco del Oro veins are in relatively short fractures. The Veta Colorada structure, located 5 kilometers to the northwest of the Prieta mine, was a major producer of high grade silver ore with low lead-zinc content during the eary 1900's. It follows a major north-south fault zone in andesite and is noteworthy for a number of wide oreshoots of limited vertical extension along its 10 kilometer length. The Palmilla and Esmeralda mines are on the south end of the Veta Colorada structure. Numerous smaller mines are operating in the Parral area. During the last 45 years the Prieta mine has produced approximately 15,000,000 tons of complex sulfide ore, principally from one single vein. Extensive stoping has

Jan 1, 1970

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.' Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.' He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.' However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.' In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957