Search Documents

By J. B. Cheatham

The influence of friction on the force required for an idealized bit tooth to penetrate a "plastic" rock is analyzed. The rock is assumed to obey the Coulomb-Mobr yield criterion and the tooth is represented by a two-dimensional sharp wedge. At the tooth-rock interface the stress field not only satisfies the yield condition but also is such that the ratio of the shearing stress to the normal stress is equal to the coefficient of friction. The solution relates the force on the tooth to the depth of penetration, the tooth angle, the coefficient of friction between the rock and bit tooth and the angle of internal friction and compressive strength of the rock. INTRODUCTION Most rocks are brittle at atmospheric pressure but exhibit ductility and increased strength as the confining pressure is increased. In a previous analysisl the force required for a bit tooth to penetrate a rigid-plastic rock was computed for two limiting conditions: (1) a perfectly lubricated tooth-rock interface which should correspond to a lower limit for the penetrating force, and (2) a perfectly rough interface which should provide an upper limit. Experimental results2 for rock indentation under confining pressure have confirmed that the analysis generally predicts upper and lower limits for the penetrating force as a function of rock properties and tooth angle. The present analysis extends the previous work to account for the friction between the rock and the tooth. ANALYSIS The force required for incipient plastic flow of an idealized model of a rock under a bit tooth is computed subjected to the following assumptions. BIT TOOTH 1. sharp two-dimensional wedge (end effects neglected) 2. rigid tooth (elastic deformation of tooth neglected) 3. displacement of tooth is normal to rock surface 4. friction exists between tooth and rock ROCK 1. semi-infinite, isotropic and homogeneous 2. rigid-plastic (elastic deformation of rock neglected) 3. non-work hardening (horizontal stress-strain curve) 4. Coulomb yield condition* (linear Mohr envelope) 5. smooth, flat surface According to the Mohr theory of failure it is assumed that failure occurs when the state of stress is such that the Mohr stress circle becomes tangent to an experimentally determined envelope. The Mohr failure curve is frequent1y approximated by a straight line and referred to as the Coulomb-Mohr failure criterion. If the rock is under sufficient pressure to be ductile we can use the linear envelope as a yield condition. The Coulomb-Mohr yield criterion is illustrated by Fig. 1 and is expressed by the following equation:l

The 114th (New York) Meeting of the Institute will be held in the third week of February, 1917. The Committee on Papers and Publica- tions has set Dec. 1,1916, as the closing date for the receipt of manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified. While Dec. 1, 1916, is the final closing date, it is a great advantage to get papers in as much before that time as possible as it enables them to be submitted in proof form to their authors. Papers received on or before

Jan 10, 1916

By J. L. Wilson, D. L. Emmons

The Tucker Hill perlite deposit is located in the northwestern portion of the Devils Garden lava field in Lake County, south-central Oregon. The perlite occurs in the chill margin of a late Miocene composite rhyolite lava dome that exhibits distinct cooling zonation. The chill margin is composed of an outer glass envelope, which contains commercial-grade granular and vesicular perlite, and an inner glass envelope, which contains onionskin perlite of local commercial quality. Glassy rhyolite and rhyolite compose the lava dome core. The entire dome complex encompasses at least 5 km2 (2 sq miles). Expansion tests in commercial-scale furnaces indicate that the perlites are suitable for a wide range of applications and compare favorably with commercial perlite ores. The large tonnage deposit appears competitive for markets in the midwestern and upper northeastern states, and the Pacific Northwest of the US.

Jan 1, 1986

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.'

Jan 1, 1956

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

By R. Simon, L. Yarborough

This paper presents a correlation for predicting the critical pressures of gas-solvent-reservoir oil systems of the type encountered in gas and solvent injection processes. Experimental data from 14 systems were used to develop the correlation which expresses critical pressure as a function of composition, C7+ mol weight, and C7+ characterization factor. Critical pressures predicted by the correlation for the 14 gas-solvent-reservoir oil systems have an average deviation of 2.8 per cent of the experimental values. The correlation war used to study a wide variety of other hydrocarbon mixtures reported in the literature whose critical conditions are in the range of interest in oil recovery work (100 to 280F and 2,000 to 6,000 psia). Critical pressures predicted by the correlation had an average deviation, expressed as per cent of experimental value, of 5 per cent for 20 miscellaneous mixtures from the literature, and 6.4 per cent for I7 methane-butane-decane mixtures reported by Sage and Lucey. INTRODUCTION Predicting critical points of hydrocarbon mixtures is an important part of phase behavior calculations. If the critical point can be predicted for a specific mixture, the separation between the bubble-point and dew-point regions will be defined, and physical properties of the mixture can be calculated by using the principle of corresponding states. Numerous correlations for predicting critical points of hydrocarbon mixtures have been published. Six of these correlationsl-8 were for light hydrocarbons, and two correlations7,8 ere for high boiling-point petroleum distillates. Organick9 And Eilerts" presented correlations which combined the published data from both light and heavy mixtures, and these correlations became the only available methods for predicting critical pressures for wide boiling range mixtures. In the course of the authors' work on secondary recovery by gas and solvent injection, experimental data were obtained for 14 mixtures of dry gas, ethane-propane-butane solvents, and various reservoir oils. The critical pressures and critical temperatures of these gas-solvent-reservoir oil systems were in the range of 1,900 to 4,800 psia and 180 to 265F. The critical pressures predicted for the 14 mixtures by the correlations of Organick and Eilerts had an average deviation from the measured values of about 13 per cent. The authors felt that it was necessary to develop a better correlation for engineering calculations and the resultant correlation, which is presented on Figs. 1 and 2, predicts the critical pressures of the 14 mixtures with an average deviation of 2.8 per cent. The validity of the correlation was tested by applying the correlation to other hydrocarbon mixtures reported in the literature. This subject is discussed later in the paper. The authors feel that there is also a need for an improved critical temperature correlation for gas-solvent-reservoir oil systems. However, developing a critical temperature correlation is a significant study in itself and is not included in this paper. EXPERIMENTAL DATA The compositions and critical points obtained by the authors for 14 gas-solvent-reservoir oil mixtures are shown on Table 1. The methane concentrations in these mixtures varied from 20 to 63 mol per cent. The intermediate hydrocarbon group, consisting of ethane, propane, and butane, varied from 20 to 64 mol per cent, and the concentration of the C,, fraction from 10 to 20 mol per cent. The physical properties of the C,, fraction covered the range from light, paraffinic, nonasphaltic (Mixtures 5, 6, 7, 8, 9 and 10) to heavy, aromatic, and asphaltic (Mixtures 13 and 14).

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965

By B. J. Dotson, P. N. McCreery, R. L. Slobod, James W. Spurlock

A core sample porosity-check program is described. A number of laboratories participated in the investigation. which comprised measuring the porosities of ten selected natural and synthetic core samples. Each laboratory employed its own method (or methods) of measurement. These included Boyle's Law, water-saturation. and organic liquid-saturation methods. Brief descriptions of each method employed are given. In general, the measured values of porosity were in reasonably good agreement. The average deviation of porosity from the mean or average values for the group of samples was ±0.5 porosity per cent. The results of these measurements are compiled and presented in graphical form. INTRODUCTION The total hulk volume of a porous sample is derived from the sum of two volumes, the void or pore volume and the solid* or grain volume. The porosity fraction of the sample ia defined as the ratio of the void volume to the bulk volume. Multiplication of this ratio by 100 converts it to per cent porosity. Distinction is made here between total porosity and effective porosity. The former includes all void space, both interconnected and isolated, while the latter includes only those voids which are interconnected. This investigation deals only with the effective porosity.* Numerous cases had been noticed in which there appeared to be appreciable discrepancies in the results of porosity determinations on core samples. Differences of as much as 10 to 15 porosity per cent had been reported from different sources

Jan 1, 1951

By P. N. McCreery, R. L. Slobod, B. J. Dotson, James W. Spurlock

A core sample porosity-check program is described. A number of laboratories participated in the investigation. which comprised measuring the porosities of ten selected natural and synthetic core samples. Each laboratory employed its own method (or methods) of measurement. These included Boyle's Law, water-saturation. and organic liquid-saturation methods. Brief descriptions of each method employed are given. In general, the measured values of porosity were in reasonably good agreement. The average deviation of porosity from the mean or average values for the group of samples was ±0.5 porosity per cent. The results of these measurements are compiled and presented in graphical form. INTRODUCTION The total hulk volume of a porous sample is derived from the sum of two volumes, the void or pore volume and the solid* or grain volume. The porosity fraction of the sample ia defined as the ratio of the void volume to the bulk volume. Multiplication of this ratio by 100 converts it to per cent porosity. Distinction is made here between total porosity and effective porosity. The former includes all void space, both interconnected and isolated, while the latter includes only those voids which are interconnected. This investigation deals only with the effective porosity.* Numerous cases had been noticed in which there appeared to be appreciable discrepancies in the results of porosity determinations on core samples. Differences of as much as 10 to 15 porosity per cent had been reported from different sources

Jan 1, 1951

By Thomas R. Cunningham, A. B. Kinzel

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By A. B. Kinzel, Thomas R. Cunningham

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By A. K. Csazar, L. W. Holm

This paper describes our investigation of a post-water-flood, oil recovery process which consists of injecting a slug of propane followed by water. Also described are the results obtained by applying a modification of the process in which gas was injected ahead of the water. Under the conditions of the latter experiments, misci-bility was not achieved between the propane and gas. Preliminary experiments or) uniform, watered-out sandstone cores showed that an oil bank could be formed and produced by applying this recovery process. However, since reservoirs are not uniform in structure, the process also was applied to porous media containing irregular porosity and to stratified sand systems. As a supplenzerrt to the experinlental work, a mathernatical procedure was developed for calculating the performance of the recovery process in a bounded, layered, porous system with crossflow between layers. As a specific example, the method was applied to predict the perforrnance of the recovery process in a 6-ft long, two-layer, stratified, unconsolidated sand model for comparison with experinlental data. The calculations were programed for the ZBM 704 computer. The equations and calcula-tional procedure presented can be extended to systems containing any number of randomly distributed permeability variations or any number of parallel layers. INTRODUCTION The problem of recovering the oil that remains in a reservoir which has been waterflooded is receiving considerable attention now as an increasing number of water floods reach an economic limit. A large number of the waterflood projects are in shallow reservoirs which are at pressures below 1,000 psi. It has been demonstrated in the laboratory that post-waterflood oil can be recover-ered by miscible displacement, but the LPG-gas, miscible flood and the enriched gas drive cannot be applied effectively at pressures below 1,000 psi. Only a few reports have appeared in the literature2-4 on low pressure, partially miscible recovery methods. However, it is possible to use LPG in a partially miscible displacement process in a reservoir where pressures of 200 to 1,000 psi can be achieved. Under these Pressures and at normal reservoir temperatures, propane is miscible with the oil; but, of course, gas or water used to drive the propane slug would not be miscible with the propane. Because of the lack of complete miscibility, it has generally been concluded that excessive amounts of propane would be required to recover oil and that such a recovery method would not be economical; however, we have found that under conditions present in certain reservoirs, an imrniscible recovery process can be applied effectively. The oil saturation in reservoirs at the economic limit of waterflood projects is usually in the range of 20 to 35 per cent of the pore space." A certain portion of this oil is left trapped by water in various size pores of the rock, but a good part of this so-called "residual" oil can be present in the less permeable lenses or layers of the reservoir rock which were by-passed to some degree by the water. The oil in these permeability traps can be produced only if favorable pressure gradients are formed in the reservoirs between adjacent zones of high and low permeabilities. A low viscosity liquid, miscible with the oil in place, which is driven by water through a stratified or heterogeneous porous system can aid in the development of these favorable pressure gradients. The oil that is released thereby from the permeability traps can be recovered by the subsequent water flood. Studies were made to determine how much oil could be recovered from homogeneous and stratified cores and models, which had been water flooded, by injecting a slug of propane and driving it with water. The effect of injecting a slug of gas ahead of the water was also determined. Most of the work described herein was done with the propane-water combination; unless otherwise specified, no gas was injected. The principal objectives of the investigation were to determine (1) if an oil bank could be formed and (2) what ratio of oil recovered to propane injected would be obtained. A further objective was to develop a method for calculating fluid-flow performance in stratified systems which would account for fluid transfer between zones in hydrodynamic communication but of different permeabilities. THEORETICAL ANALYSIS In a theoretical study of the recovery process, analytical expressions were derived to calculate the pressure distribution, the fluid flux in longitudinal (parallel to layers) and transversal (across the layers) directions, and the fluid distribution at any point in the system. The equations were developed for a two-layer porous system in which it was assumed that the fluids in the system were incompressible and that capillary and gravity effects were

By J. C. Bokros

At temperatures above 950°F, zirconium which has been strained a critical amount will experience critical recrystalli-zation. The large grain size thus formed can result in a reduction in the fatigue life by a factor of 2 to a factor of 9 at both high and low temperatures. The critical strains for zirconium vary from 15 pct at 900°F to about 2 pct at 1125°F, while those for zircaloy III vary from 15 pct at 1050°F to 5 pct at 1200°F. Zircaloy II ,experiences no critical recrystallization up to 1200°F. ZIRCONIUM has become increasingly important for nuclear applications and is being employed in reactors at temperatures where recrystallization can occur. Recent work' on the fatigue properties of zirconium has shown that coarse-grained structures developed in zirconium during recrystallization have much lower fatigue lives than fine-grained material. The development of these large grain sizes under such conditions is well known to be the result of critical recrystallization.2-4 Briefly, critical recrystallization occurs when a metal is strained a critical amount and annealed in the recrystallization range. The critical strain is defined as that minimum strain necessary to promote nucleation in the time unit and temperature considered. The maximum grain size occurs at the critical strain, since at this strain the fewest stable nuclei per unit volume grow into new grains. Recrystallization is not evident below this; strain since the nucleation rate is vanishingly lolw, and metal strained more than the critical amount has a higher nucleation rate per unit volume which results in a finer grained structure. This paper describes the critical recrystallization observed in reactor-grade zirconium, zircaloy 11, and zircaloy I11 as a function of annealing temperature and temperature of strain. EXPERIMENTAL The zirconium used was hafnium-free, double arc-melted sponge obtained from the Bureau of Mines. The ingots were forged and hot reduced to 0.08 to 0.10-in. sheet and subsequently cold reduced to 0.035-in. sheet with intermediate and final anneals at 1200 OF for 15 min. The zircaloy II and zircaloy III used were 0.035-in. sheets in the annealed condition. Compositions of these materials as tested are given in Table I. To determine the critical strain at a given temperature, tensile specimens having a0.065-in. taper in a 2-in. gage length were machined from the sheets parallel to the rolling direction. The specimens were polished, etched, and examined metallographically to ensure that all of them were strain-free, initially. Tukon indentations were made every half millimeter along the gage length of each specimen. These served as fiducial marks enabling the plastic strain to be measured with a microscope and micrometer stage. The specimens were pulled to failure at a rate of 0.002 in. per min in an Instron tensile-testing machine. Three temperatures were used for straining: room temperature, 500 ºF, and 900 ºF. The 500º and 900 ºF tests were run in an argon atmosphere. Since the rate of work hardening changes with temperature, a different critical strain was obtained for each temperature of strain. Specimens, prepared in the manner described, were annealed in vacuunl at various temperatures ranging from 900" to 1200 F for up to 1000 hr, after which they were examined metallographically. The critical strain and the recrystallized grain size as a function of strain were determined for each specimen. Results for the same temperature and time indicated that the critical strain measured was reproducible to within 5 pct of each other. RESULTS AND DISCUSSION Since increasing the time of anneal increases the probability of the nucleation of a new grain, the critical strain decreases with time at a decreasing

Jan 1, 1961

By J. H. Fletcher

ALTHOUGH some mines have been completely mechanized, on the whole mechanical equipment has made slow progress in the coal fields. Coal mining is particularly well adapted to hand labor. The skillful hand miner can keep his working place safe under difficult roof conditions, remove impurities from the coal at the point of origin, and produce a maximum percentage of large-size coal, so as to command the highest price on the market. Hand mining has also the advantage of low capital investment per ton of production and moderate carrying charge when the mine is idle. Though animal haulage gave way to electric locomo-tives and hand cutting to mining machines, beyond these concessions most of the tonnage is still produced by manual labor. But factors over which producers have no control are speeding the change to mechanical mining. The additional investment in underground equipment and surface preparation plant must be offset by a great increase in tons per man-day, and to do this the employees should be able to utilize as much of their time as possible on production. In the installation of mechanical mining, the only change in method usually has been to add loading machines to a mine already developed for hand loading. Because of a lack of suitable equipment, few mobile loading machines have been installed in seams of coal less than 4 ft. thick; the mechanization in the thinner seams has been confined largely to shaking conveyors and hand loading onto chain conveyors. Mechanical mining requires an organization that is prepared to study its particular problem from production territory to market in recognition of the changed factors arising from the use of loading machines at the working face, and other causes, such as safety of men and property; high wage scale on hourly basis; concentrated working territory and rapid extraction from a given area; change in the percentage of sizes of coal produced and effect of this on average realization. There are also the coal-cleaning problem; increased capital investment, maintenance, obsolescence, and the relation of all these to the spread between realiza-tion and production cost. If coal seams were uniform, the answer would

Jan 1, 1939

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.' This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

By A. J. Langhammer

Broadly speaking, it may be said that the engineer has two major responsibilities: One is to recommend the choosing of proper machinery and equipment; the other, to assist in the simplification of design, determination of method, and advise about the most suitable material to be used. The products of powder metallurgy enter broadly into both these fields. The oil-cushion, self-lubricating bearing surface on a machine part makes for better machinery and factory equipment, often proves a life-saver in curing difficulties where bearings are overloaded or inaccessible for lubrication, or on installations that with normal practice constitute a problem entailing frequent repairs. On the other hand, other parts may require low porosity approaching solidity. In the second field, powder metallurgy provides many possibilities for improved products, improved performance, solving of technical problems, saving of weight, quiet operation, higher factors of safety, greater flexibility, attractive economies, and so on. Parts We of the automotive industries are making many powdered-metal war-machine parts, both ferrous and nonferrous, including gears, external and internal; ratchets, both external and internal; levers; pillow blocks; sliding blocks; cams; gibs; hubs with external and internal splines, and similar units. Powdered metals play an important part in our war work, as they did in peacetime in the manufacturing of passenger cars and trucks. The art of powder metallurgy is not a panacea. Although on certain parts such operations as turning, boring, facing, reaming, counterboring, milling, countersinking. chamfering, broaching, hobbing, profiling. trepanning, gear cutting, grinding, etc., can be eliminated, there will always be the need for machine tools. Advantages of Powder Metallurgy Simple machining operations often are eliminated by using powdered metal, and also many other intricate operations, some of which are of the type impossible to perform on the most modern production equipment; for instance, an external spline on a flange hub, where the spline must continue to the flange face and at full depth. Another important feature is that some of the machine parts may require a self-lubricating surface at one or more points; for example, proper lubrication of a sliding splined spool, while ordinarily most digcuit, is accomplished automatically with a self-lubricating powdered-metal bearing. Frequently machine parts are made with physical, mechanical and technological advantages unobtainable from cast or forged metals of similar analysis. Thus powder metallurgy offers the designing engineer broader latitude. Similarly, the engineer may take advantage of powder metallurgy in his teamwork with other departments. Another important advantage in powder metallurgy for machine parts is the relatively short time required for tool-up.

Jan 1, 1945

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

ADVANTAGES OF LIFE MEMBERSHIP The Institute calls the attention of members to the following advantages of obtaining life membership: 1. One payment avoids the trouble of future payments. 2. The interest on $150 is less than the annual dues. 3. Provision is thus made early in life for the less productive years. 4. In case of in increase of clues at any time in the future life members are exempt from increased payments. Excerpt from, By-Laws. Article III. Section 3 Any Member or Associate not in arrears may become, by the payment of one hundred and fifty dollars at one time, a Life Member or Life Associate, and shall not be liable thereafter to pay annual dues. The money thus received shall be invested and only the income thereof used for current expenses of the Institute.

Jan 1, 1916

By Cyril Smith

SOMEWHAT over ten years ago the author described studies1,2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase bound-ary was accepted as substantially correct, even by later investigators3,4 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems" without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese¬silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced" to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polar-ized light and asserted that a new phase, not cubic, should be placed in the diagram adjacent to alpha. Sautner,13 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his dia-gram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4

Jan 1, 1939