Search Documents

By Ralph K. Foster

During five underground mine fires which occurred in Arizona during 1980 and 1981, sealing the fire area became necessary. To minimize leakage into the fire area, ventilation control measures were instituted to balance pressure across the bulkheads. Problems en- countered in sealing the fire areas and measures taken to improve these conditions are discussed. The routing of the ventilation and ventilation control to en- sure the workers' safety were also important considerations in reopening the mines. The use of continuous CO monitors is discussed. One important consideration was the condition of the fire, and chromatographic analysis was used to establish this. Graphs comparing the Trickett ratio, carbon monoxide, carbon dioxide, and oxygen concentrations are given. The Trickett ratio was useful but needed to be augmented by the comparison of CO, C02, and 02. Problems with getting good samples from sealed areas and recommended procedures that were developed during these fires are discussed.

Jan 1, 1982

No. 349.-A Canadian university wishes to engage a man to teach non-ferrous metallurgy and ore-dressing as well as to direct research work. The instruction work covers 7 months but the research work is continued throughout the year. To a suitable man the rank of professor will be granted. Applicants are requested to state education, experience, salary desired and any other particulars that might assist in selecting a man for this position. No. 354.-Wanted, for Northern Nigeria, one chief and two assistant mining engineers, competent surveyors, with good knowledge of alluvial tin mining and dressing of tin concentrate. Preferably with previous Nigerian experience, and exempted or able to. secure passport. Apply in writing, stating qualifications, experience and salary required.

Jan 12, 1918

By D. W. Schmidt, J. W. Shuster

Use of electric-wheel-driven haulage trucks at Chino dates back to 1963, and in today's fleet of 38 units, 17 trucks are electric-wheel- type powered with 700 hp diesel engines. Output of these engines is not adequate to exploit fully the 1200 hp potential of the two electric- wheel-drive motors, and, as a result, Chino has been testing larger prime power sources. An earlier test involved the use and evaluation of 1000 hp gas turbine engine in a conventional Model M-100 Unit Rig haulage truck (see [ ], May 1967, pp. 57-60). Now Chino has tested a trolley-diesel application in the same 100-ton capacity vehicle, and has shown that trolley power on electric-wheel-drive trucks can improve productivity rates from 18-36% on adverse grades, depending, of course, upon haul road profiles.

Jan 3, 1968

By Francis A Thomson

Montana Bureau of Mines and Geology, Montana School of Mines, Butte, Mont Francis A Thomson, President. The Bureau of Mines and Geology was formerly known as the Bureau of Mines and Metallurgy. A list of publications will be sent upon request¬ A series of six Bulletins and five Memoirs liave been issued by tlie Bureau, as well as several miscellaneous contributions Where the price is not indicated in tlie following selected list of those publications which are now available, the publications are presumably distributed gratis: Bulletin 3, Mechanical ore sampling in Montana, by H B Pulsifer (1920); 6, Geology and ore deposits of Bannack and Argenta, Montana, by P. J Slienon, 50 cents, Memoir 1, The Kevin-Sunburst and otlier oil and gas fields of the Sweetgrass Arcli, by E S Perry (1929), 2, Natural gas in Montana, by E S Perry (in preparation), 4, Tlie geologic structures of western Montana, by C H Clapp and others (in preparation), 5, Placer mining possibilities in Montana, by O A Dingman (1932).

Jan 1, 1933

B. C. MADDEN, JR.2-My comments have no connection with any particular paper; however, since we have talked of stress-corrosion cracking of aircraft parts, cartridge cases? coffee urns, bridge wire, etc., I feel I must mention the apparent significance of this symposium being held in Philadelphia, where perhaps the most famous stress-corrosion crack exists-that of the Liberty Bell. This noon I took advantage of an opportunity to see the Liberty Bell; I commend it to your attention. CHAIRMAN C. S. Cole 3That is true, the illustrations close at hand are the ones we often overlook.

Jan 1, 1945

By Frank Firmstone

IN Chemical Phenomena of Iron Smelting, Mr. Bell gives the weight of materials required to fill furnaces of various sizes at the Clarence Works ; as this differs very much from the weight required for furnaces at Glendon, where anthracite and magnetic and brown iron-ores are used, a comparison is interesting. Taking furnaces at Glendon of 4800 and 11,900 cubic feet capacity and comparing them with the Clarence furnaces of 6000 cubic feet and 11,500 cubic feet, we find that the 4800 cubic feet at Glendon and the 6000 cubic feet at Clarence required respectively-

Jan 1, 1873

By G. Don Sullivan

Surface mine operators have organized a voluntary group known as the Mined-Land Conservation Conference for the specific purpose of developing and expanding reclamation programs on mined land. As a part of the Conference program, a Voluntary Industry Program was adopted and subscribed to by its membership. This program stated: "The basic approach to a sound conservation program is the restoration of mined land to its most practical and productive use within the shortest possible time . . . reclamation of mined lands, including planting to grasses or tress, should be done on a planned basis, under technical guidance by personnel trained in this field."

Jan 7, 1965

By T. Yamasaki, S. Usu

Adsorption of potassium dodecyl xanthate from aqueous solutions on artificial and natural zinc sul-fides was studied by means of infrared absorption spectroscopy. The adsorption species and their stabilities varied depending upon the conditions of the surfaces of the zinc sulfides. Adsorption products were analyzed after they had been removed from the surface with pyridine. Zinc dodecyl xanthate was confirmed for surfaces covered with oxidized products while dodecyl alcohol and carbon disulfide were detected on purified or weakly oxidized surfaces. It is of great significance to study the adsorbed species of collectors on the surface of sulfide minerals with a view of increasing our understanding of the mechanism of flotation. Compared with other methods, infrared spectroscopy promises to be of particular value in determining the nature of the species adsorbed at the mineral/solution interface since it gives direct identification of the adsorption products; and, furthermore, it has an advantage over the electron diffraction technique which has been employed in similar problems in that infrared spectroscopy utilizes radiation of very low energy so that the probability of changing the unstable surface films during examination should be correspondingly decreased. Infrared spectroscopic studies concerned with sulfide mineral flotation have already been reported by several investigators on zinc sulfide-hexanthi01' and lead sulfide-xanthate2,3 systems. The purpose of the present study was to investigate the adsorption of potassium dodecyl xanthate (KDX) at the zinc sulfide-aqueous solution interface by means of infrared spectroscopy. Rarely is the pure zinc sulfide-xanthate system encountered in practical flotation since zinc sulfide is usually activated with small amounts of certain metallic ions, such as copper ion. However, investigation of the pure zinc sulfide-xanthate system appeared promising for studying the fundamental mechanism of the adsorption of xanthate on the sulfide minerals. Although there are few cases where xanthates having an alkyl radical higher than hexyl are employed in practical operations, KDX was used in this study since it was reported that the adsorbability of xanthate on zinc sulfide was increased with an increasing number of carbon atoms of the alkyl radicals.4 EXPERIMENTAL Samples: Experiments were made on artificial zinc sulfide and natural sphalerite. The artificial zinc sulfide was obtained commercially from Dainihon Toryo Co. as a fluorescent pigment of the purest grade A. Considering the fact that there are often cases where the surface of sulfide minerals are apt to be oxidized so that the adsorption of xanthate at sulfide mineral/solution interfaces may be substantially affected, two different procedures were employed in preparing the samples of the artificial zinc sulfide. 1) The zinc sulfide was washed with hot concentrated ammonium chloride solution (300 g per liter) to remove surface oxidation products and followed by washing with deoxygenated hot distilled water by centrifugation until the constant electric conductivity of the solution was reached (Sample I) (specific conductivity of the solution = 8.6 x l0-5 ohm-' cm-'). 2) Sample I in a suspension of 5% by weight was oxidized with a 1.5% aqueous hydrogen peroxide solution for about one hour, and then was washed with distilled water as mentioned in the preparation of Sample I (Sample 11) (specific conductivity of the solution = 1.0 x 10"4 ohm-' cm-'). Both Samples I and II were dried under vacuum and stored in a vacuum desiccator. The specific surface areas of the samples determined by the BET method using carbon dioxide gas were 19 x l04 cm2 per g for Sample I and 35 x l04 cm2 per g for Sample 11. In addition, a sample which was derived from Sample I was also prepared. In 40 ml of 3 x 10-2 M zinc sulfate solution was placed 2 g of Sample I for 2 hours, washed with distilled water by successive centrifugation until no sulfate ion could be detected and dried under vacuum (Sample 111). The purpose of this treatment will be described later. Natural sphalerite was carefully selected by hand, ground in a mechanical agate mortar for about 40

Jan 1, 1965

By J. E. Forciea, R. W. Salmi

Operating and research personnel at U.S. Steel's Pilotac concentrator have evolved specifications for magnetic separators suitable for use in beneficiation of Mesabi magnetic taconite. These specifications were developed as a result of investigations into the operating and metallurgical problems at the Pilotac concentrator over a period of some ten years. This paper discusses primary magnetic separator specifications, but much of the information is also pertinent to secondary and tertiary magnetic separators. Of particular significance is the proposal of a new basis for specifying the magnetic field which includes consideration of both field strength and field gradient. Other areas of discussion include flowsheet service, operating conditions such as drum speed and pulp level, tank configuration, magnet strength including field gradient, sleeve bearing design, designation of corrosion resistant materials and other details that result in a metallurgically efficient machine that has low repair and maintenance requirements. The mechanical and metallurgical design of magnetic separators at the Pilotac plant, Minnesota Ore Operations, United States Steel Corp. has progressed from the original single-stage, belt-type machines to the present multiple-stage, drum-type units, In ten years of operation, the plant operating and research personnel, in consultation with manufacturers, have made design changes to improve mechanical, electrical and magnetic features to meet process needs as flowsheet designs developed and to incorporate new permanent magnet materials as they became available. Separator specifications were an end result of this effort. The latest specifications which were developed for the Minnesota Ore Operations' plant were not all-inclusive listings; they covered only those points indicated by plant experience. For example, magnet pole piece design and dimensions were not stated. The manufacturers were given freedom to use any design as long as the field pattern was as specified. The selection of the items to be included in the specifications was undoubtedly influenced by particular conditions at Pilotac such as composition of plant water, concentration characteristics of the ore, repair and maintenance facilities available and the research programs that had been conducted. Only the developments leading to the specifications for a primary or "cobber" magnetic separator are presented in this paper. However, the same general concepts are used to specify secondary and tertiary separators. The areas of interest discussed include flowsheet service, tank configuration, magnet design, bearings, materials of construction, and some minor mechanical details. FLOWSHEET SERVICE The primary magnetic separators in the Pilotac Concentrator flowsheet are located after the first stage of grinding as shown in Fig. 1.

Jan 1, 1965

By Rajaraman V. Ramani, K. Sinha Atmesh, Robert Stefanko

Use of electrical power in the bituminous mining industry has increased many fold during the last few decades. Rapid changes have also occurred in mine electrical power systems in order to meet the demands from highly mechanized mines. Fires, explosions, and deaths due to electrocutions are the primary hazards due to the underground use of electricity, although there has been a marked decrease in the fatality rate from electrical accidents. However, efforts to eliminate electrical hazards and to insure trained manpower for better distribution, utilization, and protection of the electrical systems cannot be relaxed. In this article, 200 fatal accidents that occurred during the period from 1955 to 1970 have been analyzed. Accident frequency has been correlated with the size of the mine and of the work force, and with age and work and task experience. A strong negative correlation has been established between task experience and accident frequency. Though the available data permitted only a limited analysis, need for improvements in electrical power technology and for better education and training has been identified and discussed. Missing information in accident statistics is outlined and suggestions for better hazard analysis are presented.

Jan 1, 1975

By J. W. Furness

Before attempting any discussion of the importance of tariff enactments as applied to exhaustible resources, certain basic factors should be emphasized. First, it must be remembered that minerals differ from organic substances in that they are irreplaceable, and when once taken from the earth's crust enter into uses which ultimately dissipate them, so . that they cannot be recovered for future use. A second factor entering into the problem is the unequal distribution of the mineral deposits of the world. No industrial nation has within its political confines a sufficient quantity of all the minerals necessary for the maintenance and advancement of present civilization; hence international exchange of these commodities is inevitable. As minerals are essential to modern industry, the supply available to any given nation constitutes a factor which limits its ambition to advance industrially. A nation which has this ambition endeavors to secure not only a supply of minerals sufficient for its current needs, but also sources which will assure it expansion. Should mineral raw materials be withheld from such a nation by enactment, it seems inevitable that every effort will be made to obtain them, and that, should the nation deem itself sufficiently powerful, its ultimate recourse will be force. Thus the importance of tariff enactments, not only from the standpoint of industrial prosperity but from the standpoint of international peace, can be appreciated.

Jan 1, 1932

By Michael B. Moolman

Both conventional and nonconventional process alternatives for gold recovery from cyanide heap leach solutions are discussed in terms of possible flowsheets. Conventional process alternatives include carbon adsorption and zinc dust precipitation, while nonconventional process alternatives include resin ion exchange, solvent extraction, and direct electrowinning. These strategies for gold recovery are compared on the basis of technological features and on the basis of process economics: Review of the technology status and process economics suggests that improvements for conventional process alternatives are possible and that further development of nonconventional process alternatives is warranted.

Jan 1, 1984

Mounting pressures to increase efficiency and yield, conserve energy, or minimize pollution have all taken their toll on the minerals industry. As management and technical personnel take a harder look at their operations for ways to shave cents off operating costs or to squeeze a bit more productivity out of existing equipment, instrumentation often comes up as the most effective answer. When Amax Lead installed an automatic grind control system in its Buick mill, ore throughput increased by 3 to 5%. Mill operators calculate that the initial investment is returned to them several times annually.

Jan 2, 1978

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. John Birkinbine, J. E. Johnson, Jr., J. S. Unger, William H. Blauvelt, William Kelly, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. A. A. Stevenson, J. S. Unger and C. F. W. Rys have accepted membership on the Iron and Steel Committee. The Program Committee has held two meetings- in New York and has perfected the preliminary plans for the October meeting. The Committee will meet again in September. The following provisional program has been laid out by the Program Committee, but is subject to later additions and changes :

Jan 9, 1913

By Kelvin K. Wu, Daniel S. Mazzei

As a result of the 1972 Buffalo Creek disaster, the Mining Enforcement and Safety Administration (MESA), now the Mine Safety and Health Administration (MSHA) initiated the draft of new federal regulations to deal with the mine waste impoundment and refuse pile problems. Public hearings were held and finally promulgated in October, 1976. As stated in 30 Code of Federal Regulations 77.214-216, the complete engineering design plan which is mandated by the regulations has to be approved by a coal mine health and safety district manager. During the past 18 months MSHA has gained considerable experience through the submission, review, and approval process. This report indicates the procedures, general design criteria and inspection requirements for submission of engineering plans to be approved. In particular, problem areas encountered most frequently by both operators and MSHA will be discussed. Only through diligent efforts by the operators, consultants and government, can we hope to accomplish the common goal to improve the safety of operations.

Jan 1, 1982

By Herbert Clark Hoover, Lou Henry Hoover

MANY persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone ; moreover, he must understand the veins, stringers1 and seams in the rocks2. Then he must be thoroughly familiar with the many and varied species of earths, juices3, gems, stones, marbles, rocks, metals, and compounds4. He must also have a

Jan 1, 1950

DETAILED programs for the Regional Meeting to be held at Boston, on Aug. 29, 30, 31, will be available on arrival at the Copley-Plaza Hotel, where registration will begin at 10 a. m. on Wednesday morning. The opening session will be non-technical in character and will be called to order at 11 a. m. Hector J. Hughes, Dean of the Graduate School of Engineering of Harvard University, and others will speak, and in the afternoon visits are to be made both to Harvard and Massachusetts Institute of Technology. Wednesday afternoon will be devoted mainly to the opening of an exhibit of geophysical instruments and methods at Tech. On the way back to the hotel a tour of Old Boston will permit the visitors to see many of the historic points of the city. A special meeting of the Board of Directors has been called to be preceded by the usual subscription dinner at the University Club at 6.30 p. m. Owing to limita-tions of room, invitations have been sent only to the usual list designated in the By-Laws, the Directors, past officers, chairmen of sections and of technical committees. The dinner and a brief business session of the Board will be followed by a technical session at the Copley-Plaza at 8 p. m. and this in turn by a buffet supper at the University Club at 10 p. m. Sep-arate entertainment is being provided for the women for the evening. Thursday will be devoted to technical sessions both in the morning and afternoon. If necessary to permit adequate discussion, an overflow session will be ar-ranged in the afternoon. In the evening, a subscription dinner will be given at the Copley-Plaza at which past-presidents John Hays Hammond and Robert H. Rich-ards will be guests of honor. It is promised that speeches will be short and dancing will be arranged for following. The women will be offered a luncheon and bridge party at one of the country clubs on Thursday, and Friday will be devoted to an all-day excursion for both men and, women. Members are asked to register promptly on arrival so that the various committees will know as early as possible for how many to provide. The major part of the technical program has been provided by the Committee on Geophysical Methods of Prospecting, and a series of papers of great value and interest in this new field has been brought together. Abstracts of substantially all of them are printed in this issue of MINING AND METALLURGY and the papers themselves will, with one or two exceptions, be avail-able in printed form at the meeting and later in the regular publications of the Institute.

Jan 9, 1928

By J. L. Weeks

THERMAL conductivities of several samples of uranium and uranium alloys were determined using an apparatus previously described.' The value previously reported for uranium,' 0.035 cal per sec per cm per "C at 70°C, is in error due to the failure of a thermocouple during the determination on uranium. The defective thermocouple was detected after a reanalysis of the data obtained during the run and since has been replaced. Subsequently, runs on several samples of uranium show the thermal conductivity of uranium to be 0.069 cal per sec per cm per 'C at 70°C. The accuracy of the determinations was checked by measuring a sample of synthetic sapphire whose thermal conductivity was previously reported and found to be in agreement with other values."-" The values given in Table I are believed correct to % 3 pct or 0.003 cal per sec per cm per "C, whichever is larger. The samples were provided by J. H. Kittel of the Argonne National Laboratory, Metallurgy Div. References J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal American Ceramic Society (1952) 35, p. 15. :' J. Francl and W. D. Kingery: Thermal Conductivity: IV, Apparatus for Determining Thermal Conductivity by a Comparative Method; Data for Pb, Al2O3, BeO, and MgO. Journal American Ceramic Society (1954) 37, No. 2, Part 11, pp. 80-84. (Part 11: special issue on thermal conductivity.) ' W. D. Kingery, J. Francl, R. L. Coble. and T. Vasilos: Thermal Conductivity: X, Data for Several Pure Oxide Materials Corrected to Zero Porosity. Journal American Ceramic Society (1954) 37, No. 2, Part II, pp. 107-110. (Part 11: special issue on thermal conductivity.) Edwin Ruh: New Jersey Ceramic Research Station, Rutgers University. Private communication.

Jan 1, 1956

By O. B. Bucklen, J. P. Matoney, P. G. Meikle, R. L. Terry

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also holds true for loading and storage facilities. Where once a 1 million st per yr (910,000 mt/yr) mine was rare, 3-5 million st per yr (2,730,000-4,550,000 mt/yr) mines are not uncommon today in the bituminous industry. This great increase in production, made possible through mechanization, requires greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend to- ward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw-coal storage and blending facilities. The development of the unit train with its attendant economics has contributed more than any other factor to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has added to the need for faster and larger loading facilities. In this climate of rapidly changing technology, any written ac-

Jan 1, 1979