Search Documents

By Peter Sonnenfeld

Bedded potash deposits are known only from Phanerozoic evaporite sequences. They are composed of either sylvite or carnallite, of which only the former produces commercial potash ores. Both Permian and Neogene potash deposits have experienced sulfatization by percolating oxygenated surface brines, causing enrichment in the potash content. Permian potash deposits are mined in various parts of Europe and North America, Miocene ones only along the outer rim of the Carpathian Mountains and in Sicily. New discoveries of large Miocene rock salt bodies make it possible to predict the occurrence of potash deposits along their flanks.

Jan 1, 1985

By M. Dubrovsky, J. W. Evans

A laboratory scale cell (approximately 50 amps current) equipped with a fluidized bed cathode was used in a study of the electrodeposition of cobalt from acidified aqueous sulfate solutions The effect of current density (in the range 0.1 to 1 amp/cm2 of diaphragm), cobalt concentration (4 8 to 100 glliter) and catholyte pH (1 35 to 6 2) on current efficiency and energy consumption were determined. Generally the current efficiency increased with increasing current density and cobalt concentration Current efficiencies were comparable to those reported in the literature for conventional electrowinning

Jan 1, 1981

By V. F. Zackay, J. F. Carlson

CURRENT experimental work on the development of gas turbine engines in the automobile industry has emphasized the need for a relatively low cost nonstrategic castable alloy for service in the 1200" to 1400°F temperature range. Ferritic steels

Jan 1, 1956

By Ralph E. Wood

X-ray fluorescence analysis can be profitably applied in the mineral industry by improving evaluation and control analyses, while offering lower cost and greater speed than conventional methods. Chemical analyses are not only a major item of cost in exploration and mining, as well as in milling and chemical treatment, but often cause evaluation and control of processing steps to lag behind operations. In the fields of geology and mining, the X-ray technique can be employed without destroying samples and, if necessary, specimens can be analyzed and then used, unchanged, in other evaluation techniques. Results are quickly made available for decisions on progress of exploration or sorting of waste and ore.

Jan 6, 1959

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.OO Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By William A. Prichard

After a study of the excellent geological reports and maps prepared by the United States Geological Survey,? and after practical experience in working the ore-deposits in this field,

Jan 1, 1904

By John V. Beall

Beall: Mr. Bennett, you have had a very successful -and a very colorful-career in mining. Would you tell us about your first job in the mining industry? Bennett: I was a mine surveyor on the Mesabi and Marquette ranges, working both open pit and underground. I worked two years for the Meriden Engineering Co., formerly the Meriden Iron Co., which was founded in 1904 to operate mines and to act as a lessors' agent for inspection. At the time I was there, Meriden was operating one open pit and one underground mine, and acting as agent or inspector for some lessors, the owners of the fee interest.

Jan 1, 1968

By M. D. Cooper

Production of both anthracite and bituminous coal in 1954 was about 16 pct below 1953. Estimates on Dec. 1, 1954, indicated 27 million tons of anthracite and 385 million tons of bituminous. Decline in production was due principally to lower demand by the steel industry and the railroads, although competition from other fuels also affected coal. The year was notable for vigorous effort by the coal industry to promote the use of its product. A Cabinet Committee on Energy Supplies and Resources Policy and an Interdepartmental Committee on the Soft Coal Industry were set up by the Administration in Washington. A Governors' Fuel Conference was also organized.

Jan 3, 1955

By R. E. Bish

IN an effort to distinguish experimentally between the radically different limits of two-liquid im-miscibility reported for the Cu-Pb system by Borne-inann and Wagenmann and by Briesemeister (see Fig. I), it was found that the high temperature homogeneous liquid containing between 41 and 93 pct Pb could not be frozen without separation into two liquids with the fastest cooling technique that could be devised. Thus, the two-phase state could not be distinguished with certainty from the one-phase state by the examination of quenched samples. To overcome this obstacle the following method for detecting the presence of an interface between two immiscible conducting liquids at temperature was developed. Measurements made by the new method substantiate the Briesemeister diagram in its general form. The method consists essentially in the measure-

Jan 1, 1953

By Kenneth K. Humphreys, J. W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of - '/4 in. ( -6.3 mm) coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing salable coal to the fine coal cleaning section of the preparation

Jan 1, 1979

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the inter-relationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large. Coming to the specific points to which Mr. Borden has drawn our attention, I will touch on the corresponding provisions in Canadian federal tax law, by way of comparison and contrast.

Jan 7, 1950

By Colin C. Harris, Nathaniel Arbiter

The flotation operation can be analyzed in terms of three groups of variables. The first, largely independent of control by the operator, embraces the fixed physical and chemical properties of the ore minerals. The second includes all chemical and physical effects imposed on an ore after mining that influence its floatability. These can be either purposefully or accidentally applied. The third embodies the flotation-machine characteristics which realize the potential floatability of selected ore minerals in terms of grade and recovery levels. The machine effectiveness thus depends not only on its own contribution, but on the prior influence of all other variables on floatability. HISTORICAL DEVELOPMENT From the earliest days, flotation mills used many types of machines. Hoover 20 in 1914 mentioned as then important the Potter-Delprat tank for gas generation by acid, the DeBavay cones for skin flotation, the Elmore mixer and separation chamber for vacuum flotation, and his own modification of the Mineral Separation cell for the agitation froth process. Less important at the time were the MacQuisten tube and the Hyde cell. By 19274~ scores of machines had been developed and dozens had found their way into mills. From then on, however, under the scrutiny of competitive tests, many fell into disuse. Taggart in 19454~ classified processes broadly as skin flotation and froth flotation, dividing machines for the latter into the three categories: bubble column, pulp body, and combination.* Under 'bubble column' he listed all pneumatic, cascade, and subaeration cells; and under 'pulp body' those cells in which gas was generated by boiling, chemical action, and pressure reduction, as well as the agitation-froth type. At that writing skin flotation, the cascade machines, and all pulp body and combination machines were said to be extinct, leaving pneumatic and subaeration types dominant (u. S. practice). The process of elimination has continued to the present, with almost all pneumatic cells succumbing to the pressure of competition from subaeration machines. The only new machines to appear in recent years have been double-impeller types f and these have met with only limited acceptance.

Jan 1, 1962

By William P. McConnell

At the dawning of the first century of AIME, mechanical handling of bulk materials was largely confined to movement of grain and light mill products by belt and screw conveyors, but grain handling experience inevitably led to the use of the belt conveyor for coal, ore and other heavier materials. In 1891, the first major U.S. conveyor installation for heavy minerals was completed at the Edison, N.J., plant of the New Jersey & Pennsylvania Concentrating Co. Functionally, this plant revealed its grain elevator heritage. Overlooked at the time of design or, perhaps more accurately, not fully recognized, were the dramatic differences between grain and minerals in both operating conditions of the system and the physical characteristics of the material to be conveyed. This inevitably caused problems, but from the ashes of these problems rose solutions. The Edison plant became a proving ground from which came two significant developments by Thomas Robins-the first conveyor belt designed specifically for impact loading and abrasive materials and the three-roll conveyor idler. As an installation with more than 50 conveyors in widths of 20-30 in. and belt centers of up to 500 ft, the plant was a landmark, for it established the belt conveyor as a vital method of trans- porting heavy, abrasive materials.

Jan 1, 1971

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Engineer, 43, married. Sixteen years' experience mining. Desires permanent position mine superintendent. Broad knowledge all types underground mining and shaft sinking. Construction and milling experience. Prefer North American continent but will accept foreign. Presently located Australia but available May 1, 1953. M-706. POSITIONS OPEN Mining Engineer with broad exploration experience, young, single status, and must be in excellent physical condition, as nature of work will be under very primitive conditions. Salary about 25 pct more than applicants last salary rate plus travel expenses and living allowance. Duration until July 1953. Location, Burma. Y7498.

Jan 1, 1952

By George Hulst

PRIOR to 1914, there was little demand for antimony in this country; its use was limited almost entirely to the manufacture of type and bearing metals. Practically no antimony ore was mined here, the market being supplied principally from China, and the alloy was produced by a direct mixing of lead and antimony. The great world war, with its demand for shrapnel in hitherto undreamed of quantities, precipitated a great boom in the price of antimony. Nominally quoted at 6 c. to 7 c. in 1914, the price increased by leaps and bounds to 45 c. in March, 1916. Under the stimulus of high prices many shall mines were opened, for it became profitable to work ores containing as low as 20 percent. antimony. High-grade sulfide ores (stibnite), containing 55 per cent. to 60 per cent. antimony, were received from Bolivia, China, and Alaska. Low-grade sulfide ores, running from 20 per cent. to 45 per cent., were produced in Nevada, California, Idaho, Utah, and Mexico; much of this ore was fairly rich in silver. The principal oxide ores came from Mexico and Oregon. The following analyses are representative of various types of antimony ore: Se Pn Cu Ao Au SIC), Fe S CAO ZN As Oxide Ore 25.09 46.02 0.95 0.40 10.98 0.30 0.22 Sulfide ore 5.5.20. 15.12 1.05 19.87 ? 0.40 0.25 Sulfide Ore 37.16 11.30 0.10 34.0 7.60 0.50 17.05 7.40 0.36 0.10 Sulfide Ore 41.55 15.00 0.20 76.0 0.04 5.60 0.25 18.17 0.85 0.25 0.10 The International Lead Refining Co. fortunately was equipped to handle these ores through residue and blast furnaces. The charge consisted of a variety of sulfide ores containing Sb 20 to 60 per cent. and Si02 6 to 45 per cent., oxide ores containing Sb 20 to 40 per cent. and SiO2 10 to 45 per cent. Secondary materials, such as battery plates, battery mud, lead oxide, paint, etc., together with refinery skims, softener skims, and other refinery byproducts, were treated along with the antimony ore to furnish the lead required. All silver-bearing antimony ores were treated in the residue furnace, the sulfur, iron, and copper forming matte that carried part of the silver, the balance going into lead bullion. The

Jan 9, 1919

By William G. Neilson

Edward Nichols died at Dunkirk, N. Y., January 7, 1892, in the forty-second year of his age. In the maturity of his powers, actively employing the strength gained from the experiences of a busy lift., and occupying positions

Jan 1, 1893

By Peter M. Grant

The paper describes in broad outline the design of circular shaft linings with particular reference to the practical aspects. In the main it refers to recent British and German practice but has general application for any shaft lining design.

Jan 1, 1983

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

Abstract-In this paper an attempt has been made to review the cost trends in producing copper by conventional milling, smelting and hydrometallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 4, 1978