Search Documents

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

By C. H. Curtis

The valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 4, 1950

By AIME AIME

THE initial meeting on Mining Methods* opened at 10 o'clock Monday morning with Scott Turner as chairman and W. Spencer Hutchinson as vice- chairman; about 60 attending. After preliminary announcements Theodore Marvin was called on for his paper,, entitled "Rock Tunnel Methods," which has been appearing serially in The Explosives Engineer. Marvin read the introduction and called attention to the account of one or' two particularly' interesting projects, such as the. Brooklyn water supply tunnel. E. D. 'Gardner, Char1e.s S. Hurter, L. D. Lamont and Spencer P. Howell took part in the discussion, Howell commenting on the fact that, in one case cited, misfires had occurred through detonator wires 'coming in contact with the case of an unapproved flashlight, .,: and that all flashlights should be approved.

Jan 1, 1931

By R. Dawson Hall

Discussion of the paper of R. DAWSON HALL, presented at the San Francisco meeting, September, 1915, and at the New York meeting, February, 1916, and printed in Bulletin No. 105, September, 1915, pp. 2013 to 2021. R. DAWSON HALL, New York, N. Y.-The general practice in the past has been to view the roof as being somewhat subject only to shear. In fact the action of the roof under the stress of its own weight has been but little considered, not because the matter is unimportant but because it is so complicated that it has been felt that an analysis of it would not result in any conclusions definite enough to justify the inquiry. The result has been that the consideration of the subject has fallen into the hands of persons who are not experts in the study of beam and plate stress. They have been disposed naturally to view the destruction of the roof as the outcome of the simplest of stresses-vertical shear. In the lack of a careful consideration of the conditions of roof fracture it was thought that the roof consisted of a number of horizontal layers, which were each of them weak, because, no matter how strong they might be they usually lacked sufficient depth. This view of the condition of the roof would naturally lead one to expect that it would yield to bending moment, the various layers succumbing one by one to their lack of the necessary radius of gyration to meet such severe stresses. But,

Jan 5, 1916

By Charles F. Brush

THE compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

Jan 1, 1876

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104'c per sec for 0.010 in thick specimens, as calculated from Newton's law of heat flow2 using a heat transfer coefficient of 25 ft-'. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By R. F. Steigerwald

The effects of heat transfer on the corrosion behavior of type 304 stainless steel in boiling water have been studied. Heat transfer conditions increase the tendencies of the stainless steel toward stress-corrosion mucking when the water is contaminated with Cl-. Surface preparation is the most important variable in determining the severity of the stress-corrosion problem in water with a given Cl- content. Heat treatment, chemical cleaning, and degree of wet film boiling also affect the corrosion of stainless steels used as heat transfer surfaces in boiling water. An up-paratus for corrosion testing under controlled heat transfer conditions is described. THE principal objective of this investigation was to study the corrosion behavior of AISI Type 304 stainless steel in boiling high-purity water under conditions of heat transfer. The principal variables in the study were: a) boiling conditions: limited boil, agitated boil; b) metallurgical structure: annealed or sensitized; c) surface condition: rolled, pickled, or ground. The results of the study should elucidate the role of heat transfer in the corrosion of stainless steel in boiling high-purity water and provide a base line from which to assess the severity of this type of corrosion. Although there has been an investigation of the effect of heat transfer on the corrosion behavior of stainless steels in alkaline waters,' work on the corrosion of stainless steels under heat transfer has been largely confined to various acid solutions.'-4 Furthermore, the study of the corrosion of stainless steels in high-purity water has been generally restricted to auto-clave and instream testing in superheated (e.g., 300°C) water and steam.5'6 Cooling water problems led to this study of the corrosion behavior of type 304 stainless steel in high-purity water at its atmospheric boiling point. In addition to the effects of heat transfer, this study also considered the influences of the type of boiling,7 metallurgical structure, and surface condition on the corrosion behavior of stainless steel in high-purity water. Two boiling conditions were investigated in this study: a) limiting boiling, i.e., when the heat-transfer surface had just reached the boiling point and boiling nucleated randomly over the specimen surface and b) agitated boiling, i.e., when a mild degree of superheat had been achieved on the specimen surface and boiling occurred generally over the specimen surface. Both boiling conditions are broadly classified as wet-film boiling. Originally, this program included the study of a third type of boiling, dry-film conditions. At dry-film boiling the temperature of the heat transfer surface is high enough so that it is covered with a continuous film of steam. Experimental difficulties made it impossible to study this kind of boiling with the available apparatus. Since surface condition affects heat transfer rates, three typical surfaces were chosen for study: a) as-rolled, the 2B finish received from the supplier, b) as-pickled, 30 min in 8 pct HNO3-1 pct HF, and c) as-ground on 120 grit paper. In order to evaluate the effect of improper heat treatment or welding on hot wall corrosion, both annealed and sensitized mi-crostructure were included in this study. EXPERIMENTAL Test Apparatus. The particular problems of interest in this investigation required a knowledge of the thermal gradient through the test specimen. From this gradient, the heat flux to the surface and the surface temperature could be determined. In order to satisfy this need, an apparatus similar to the boiling-disk apparatus of Fisher and whitney2 was designed. The solution is contained in a thermally-insulated, steel pipe lined with TEFLON resin. A stainless steel _______;________________________________________

Jan 1, 1970

By Louis Katona

The practical execution of the design for rolling-mills presented by the writer at the Paris meeting* of thc Iron and Steel Institute in 1900 involves the determination of some questions not yet discussed, among which is the determinatioir of the amount of power required to perform the rolling of pieces of iron and steel of given dimensions. It is necessary to know this factor if we would put motors of proper capacity to the respective pairs of rolls, or, rcciprocally, if, having standard motors at our disposal, we would design grooves to suit them. Moreover, this factor is involved in giving right dimensions to every part of the rolls and housings. Expert designers of engines for driving rolling-mills of the present type receive very indefinite directions, such as: that the motor is to drive a light, medium or heavy train; that it must work with fly-wheel or reversing gear; that the number of revolutions per minute should not exceed 40 or 60, and that at a given speed the power developed should be from 100 to 200 H. P., or from 1,000 to 2,500 13. P. It frequently happens, however, that an cngine of 200 H. P. is forced under the circumstances to press or develop as much as 300 H. P., while, on the other hand, the ,1,500-11. P. engine may be rolling-stock which could be worked with a maximum expenditure of 60 to 80 H. P. Of course such variatior~s as these do not permit the best adjustment of parts or the best economy of power and fuel. The design of roll-trains is even more vaguely limited. Every part of a train, from the point where it connects with the engine to the last groove in the rolls, bears evidence that there are no rules for calculating even approximately the dimensions of the main-shafts, couplings, pinions, gears, rolls, trunnions,

Jan 1, 1904

By Dan A. Permenter

This paper assesses some of the critical factors that must be considered and addressed in the implementation of small computer systems for technical applications within a coal company. Aspects of hardware selection that are somewhat specific to the coal industry are discussed, and a table of potential areas of application is presented. The dilemma of internal software development is presented and a software development program based on a users group approach is outlined and discussed in detail.

Jan 1, 1983

By E. Brunner, G. L. Hassler, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By G. L. Hassler, E. Brunner, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By R. J. Wysor

MoRe than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same, furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100" F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently done some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C.,R. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based on the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations. Method of Conducting the Tests The location of the pyrometer fire ends is shown in Fig. I, a plan of Bethlehem Steel Co.'s "G" blast furnace, hot-blast stoves, and main. Bare fire ends were used at both positions "A" and "B," being inserted

Jan 1, 1916

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on' the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently published by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so desirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his materials ; by regulating the supplies of air and fuel ; by arranging his plant in the most economical manner, and by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconstruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, and yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

Jan 1, 1877

By E. J. Ripling, S. I. Liu

IT has been shown in a number of recent publications that much information on the mechanical behavior of metals can be gleaned by first deforming test specimens under one set of conditions, and then evaluating the effect of this deformation by means of a subsequent tensile test. A straining procedure of this type has been applied to study the flow behaviors of a number of metals.1, 2 In these studies the prestraining and testing were both tensile strains, while the straining temperature was varied between the prestraining and testing steps. These data indicate that there is a more or less general flow behavior exhibited by all metals which are pre-stretched at one temperature and then tested in tension at a second temperature. Prestraining a metal at a high temperature produces a lower yield strength during the subsequent low temperature strain than would the same total strain at the lower temperature. On reversing the order of the strains, low temperature prestraining produces a higher yield strength during the subsequent high temperature straining than would a single high temperature strain of the same magnitude. Unlike the flow behaviors, the fracturing characteristics of metals when prestrained under one set of conditions and tested under a second set of conditions is quite material dependent. The fracture behavior of a number of steels2" as well as of a commercially pure zinc,4 have been investigated by these two-step tests and was found to depend upon the position of the transition temperature with respect to the prestraining and testing conditions. Since these fracturing phenomena are complicated by the appearance of the transition temperature, it has been difficult to reliably define the basic effect of a two-step straining procedure in fracturing. Metals crystallizing in the face-centered cubic system do not exhibit transition temperature effects so that the mechanical characteristics obtained on these materials could serve as a base for two-step straining behaviors. Consequently groups of specimens of the aluminum alloy 24s-T4 were prestrained various amounts at room temperature in either tension or compression after which these strained specimens were further strained to failure, or tested in tension, at either room or some lower temperature. Other groups of 24S-T4 specimens were prestretched at various low temperatures after which these were tested in tension at room temperature. These straining techniques then made it possible to compare the behaviors of aluminum with the behaviors previously presented for steels. Material and Procedure The commercial aluminum alloy 24S-T4 in the form of 3/4 in. rods was used in this investigation. The material was subjected to the following treatments before machining: 1—resolution treating at 920" & 10°F for 45 min, 2—quenching in water at room temperature, and 3—aging at room temperature for four days. The re-heat treated material was then machined to either of the specimen shapes shown in Fig. 1. Fig. la shows the threaded-end specimen used for prestraining in compression. Fig. 1b shows the specimen used for both prestrain in tension and final testing. The material subjected to precompression in the form of the specimen shown in Fig. la was re-machined to the specimen shape in Fig. 1b for final testing. Prestraining in tension and final testing were done without any intermediate machining. All straining was performed on a 10,000 1b Riehle tensile testing machine. Tensile strains were conducted in a specially designed concentric fixture which produced an eccentricity of less than 0.001 in." The change in diameter at the minimum section of

Jan 1, 1954

Jan 1, 1978

By Gilbert P. Moore

Production in the Argentine in 1930 amounted to 1,415,099.7 metric tons, which converted into barrels of 42 gal., using the factor of 6.29, amounts to 8,909,773 bbl. This is a decrease of 481,613 bbl. from the 1929 production, which was 9,391,386 bbl. The production for 1930 was divided among three fields, as shown in Table 1. Table 2 covers Table 1.—Argentine Oil Production, 1930, by Fields Barrels Comodoro Rivadauia District Government........................................... 4,547,670 Railways Co........................................... 1,314,358 Astra-Eastern......................................... 1,016,024 Anglo-Persian......................................... 365,021 Solano Co............................................. 24,613 Dutch Shell........................................... 6,963 7,274,649 Neuquen District Government........................................... 569,245 Standard Oil-Argentina................................. 659,551 Astra-Eastern......................................... 8,234 Challaco Co. (Sol)...................................... 121,598 1,358,628 Salta District Government........................................... 90,576 Standard Oil-Argentina.................................. 185,920 276,496 8,909,773

Jan 1, 1931

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently pub lished by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so de sirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his ma terials ; by regulating the supplies of air and fuel; by arranging his plant in the most economical manner, arid by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconsiruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, arid yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

By G. V. Woody, J. D. Price

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By J. D. Price, G. V. Woody

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944