Search Documents

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By Kiyoshi Mizui

Processes for manufacturing prereduced iron pellets from iron ore dust occurring in iron works have recently begun on an industrial scale. Because of their high porosity and low mechanical strength, these prereduced iron pellets tend to oxidize again and disintegrate into fine particles during transportation and storage; this may result in such difficulties as decreased yield, undesirable work environment and heat generation during oxidation. A possible process for avoiding oxidation and disintegration of prereduced pellets is increasing the density through briquetting. The authors carried out briquetting tests under various conditions, attempting to find optimum briquetting conditions. They found that crushing prereduced pellets and adjusting the particle size to a certain range before briquetting increased the briquette strength and reduced the amount of binder needed. Oxidation resistance of briquettes and raw material pellets was compared in open air and at high temperatures. Briquettes showed superior oxidation resistance.

Jan 1, 1977

By Whitman E. Brown

The installation in 1948 of a Humphrey spiral concentrator section at the Hill-Trumbull plant of The Cleveland-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus 1/8 in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 44 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus 1/8 in. size. After desliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant.

Jan 1, 1949

By George J. Young

(Cleveland Meeting, October, 1912.) I. GENERAL. THE recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may he enumerated as follows: Forman Shaft fire., Gold Hill, April 21, 1903 ; shaft-house, machinery, and shaft, destroyed; loss estimated at $50,000.; Cause Unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery, and shaft in part destroyed; loss estimated it $100,000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909 ; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause ' probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started in winze ; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911 ; fire originated iii shaft-station from unknown cause; 7 men killed, and $34,¬521 damage caused. (NOTE 1.-On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and laming of the pump-room. The pump-roan in charge notified the surface, and the * Professor of Mining and Metallurgy, Mackay School of Mines.

Oct 1, 1912

By Carl F. Floe, Michael B. Bever

ACCELERATED by the demands of war, research and development work in nonferrous physical metallurgy has continued at a rapid pace during the past year. In particular, advances have been made in processing and fabrication, especially of the light alloys, and in the surface treatment of metals. Theoretical physical metallurgy, although less active, has not been neglected and the year has brought forth some -notable contributions to our understanding of the fundamental structure of metals and their behavior in service. Of course, much work that has been done cannot be publicly discussed because of wartime restrictions.

Jan 1, 1945

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptability. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new combination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmission to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 1, 1950

By FORTUNATO PEREIRA

(San Francisco Meeting, October, 1911.) I. GENERAL DESCRIPTION. The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, FIG. 1.-SKETCH-MAP OF THE SOUTHWESTERN PART OF COLOMBIA. near the boundary of Ecuador, as shown in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the principal towns are Túquerres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Aug 1, 1912

By B. H. Bergstrom, C. L. Stevenson

In any process wherein materials must be pelletized, a crucial period exists during the interval between the manufacture of the green pellets and their subsequent heat treatment. The pellets must possess sufficient strength and plasticity to withstand conveying and sizing. Also, they must be neither excessively brittle nor excessively plastic when placed in a bed on a traveling grate for heat treatment. An acceptable pellet, in the event sufficient forces are applied to cause its fracture, will merely split into two or three large fragments which would not drastically alter the permeability of the pellet bed. However, when brittle pellets are broken, they shatter so that the resultant fine particles either decrease the perimeability of the bed or become entrained in the gas stream and thereby cause dust problems. On the other hand, excessively plastic pellets may not break at all but may merely flatten. This would seriously hamper bed permeability. In the past, pellet evaluation has usually been left to the creative and artistic talents of the balling operators. A multitude of techniques have evolved, of which the most common is the simple compression test. For this test a hand-operated device loads single pellets to fracture, but reliability is strictly operator- dependent. Probably the next most common test is the drop test, which is conducted according to several different procedures. This is an important quantitative test for estimating the amount of handling a pellet will withstand. There are many other tests, such as pinching a pellet between the thumb and index finger, but none are capable of producing reproducible results.

Jan 4, 1962

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

George Smith, Sydney, N. S. Wales (communication to the Secretary): The very interesting paper by Mr. Emmons on " The Secondary Enrichment of Ore-Deposits " has just come under my notice; and its reference to my own paper* on " The OreDeposits of the Australian Broken Hill Consols Mine "† is therefore only noted some two and a half years after its publi-

Jan 1, 1903

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input—heat enerb output) used in creating new surface, gliding or slip on atomic planes, twinning, and possibly other lattice rearrangements within the mineral. If it be postulated further that with a hard, brittle crystalline material, such as quartz, the energy used to produce gliding, twinning, and other permanent lattice movements is a very small fraction of the total net energy absorbed, then this energy absorption within the grinding calorimeter can be ascribed to the creation of new surface energy alone. Such energy is, from the thermody-namic standpoint, the true effective work of the grinding device, in this case a tumbling-medium mill. The ratio of this effective work (in calories) to the total energy input (in calories) should express the thermodynamic efficiency of the comminution taking place under the conditions used in the grinding calorimeter. This approach to the measurement of the energetics of tumbling-mill grinding was suggested by some previous work by Fahrenwald and coworkers' with a laboratory ball mill and a thermometer. They measured the efficiency of grinding based on the formula: Pct Grinding Efficiency = Energy (calories) — Thermal Energy x 100 1npZ Output (calories) Energy input (calories) Efficiencies thus measured, while grinding quartz sand, ranged from 19.7 pct to 7.4 pct. Cook in 1915,' used this approach to the problem of grinding efficiencies in stamp batteries and obtained the energy input by stamp weights times drop distances and the energy output by means of thermometers and pulp flow rates. He calculated that 80 pct of the input energy to the stamp shoes was wasted as sensible heat in the ore pulp. No other studies of comminution by this method of energy differences came to the author's attention. Reasonable agreement as to the order-of-mag-nitude of comminution efficiencies in tumbling-media mills is lacking in the literature. There is a widespread impression among technical workers that the grinding efficiency of the industrial ball mill may be on the order of 1 pct, or even a fraction

Jan 1, 1952

By Donald B. Evans, Robert D. Pehlke

The solubility of nilrogen in liquid binary alloys of iron with Litanium. zivconium, columbium, vanndiurn, and tantalum was measured for alloy composiLions up to the solalbility limils of lhe alloy nitrides. All five alloying agents were found to decrease markedly the activity coefficient of nitrogen in liquid ivon. The metal/nitvogen mole ralios in the alloy nitrides formed were generally .found to be slighlly greater than 1.0, but in no case greater than 1.5. From the experimental data, the standard free energies of fortmation of titanium and zir-conium nitrides have been calculated for the Lemperaluve range 1550° to 1750 C. The solublily Products for columbium, tantalum, and vanadium nitrides are also reported. A number of research investigations have examined the effect of refractory metals on the solubility of nitrogen in liquid iron. Although data on zirconium are not available, investigators are in agreement that titanium, vanadium, columbium, and tantalum markedly increase the solubility of nitrogen in liquid iron. This fact alone makes desirable the acquisition of thermodynamic data for these elements in liquid iron. Since refractory metals are known to be stable nitride formers, they have been suggested as steel denitrifying agents, and some of their nitrides have recently been considered as containment materials for liquid iron and iron alloys. Most available thermodynamic data for these metals relate to their dilute concentrations, but effective thermodynamic treatment of these applications requires data at concentrations near the solubility limit of the alloy nitride. Although some work has been done at relatively high alloy concentrations in liquid iron (particularly for vanadium 2,3 and titanium 2,4), the results have been somewhat contradictory. Disagreement may be partly attributed to the fact that the compositions of most refractory metal nitrides have been shown to be nonstoichiometric, and to vary 2,5-8 depending on the temperature and nitrogen gas pressure with which the solid nitride phase is in equilibrium. One purpose of this study consequently has been to determine the compositions of the refractory metal nitrides precipitated from a liquid iron solution. EXPERIMENTAL PROCEDURE Rao and Parlee2 and Evans and Pehlke 9 have discussed the technique for measuring the solubility product of an alloy nitride phase in liquid iron by finding the point of departure of the nitrogen solubility from Sieverts' law. The method consists of measuring the solubility of nitrogen in a melt of iron containing a known concentration of a second metal as a function of the nitrogen gas pressure over the melt. In this study the second metal was one of the refractory metals titanium, zirconium, columbium, vanadium, or tantalum. When the nitrogen pressure at which the refractory nitride forms is reached, a deviation of the measured solubility of nitrogen in the melt from Sieverts' law is observed in the form of a "pressure halt." The concentration of nitrogen in the melt associated with this breakpoint in the nitrogen-absorption curve is then used to calculate the nitride solubility. The Sieverts method was used to measure nitrogen solubility as a function of nitrogen pressure and temperature. The experimental equipment for this technique has been previously described in detail. 1,9 Charge materials used were vacuum-melted high-purity iron (Ferrovac-E) and the best commercial grades of the refractory metals obtainable (in all cases at least 99.8+ pct pure). Recrystallized alumina crucibles were used to hold all melts except those containing zirconium, for which zirconia crucibles were necessary. Temperatures were measured by a disappearing-filament type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diameter sight hole in the crucible lid. By means of a technique previously described, 9 in which the refractory-metal nitride was precipitated at one temperature then redis-solved by raising the temperature 50°C and precipitated again at a higher temperature, it was possible to obtain data over a temperature range of up to 200°C on a single melt. It was found that this technique could not be used with melts containing zir-

Jan 1, 1965

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

L. S. Austin, Denver, Colo. (communication to the Secretary) : Mr Hartman says (p. 4 of the pamphlet) that the penetration of air into the crucible of the blast-furnace " is, of course, a function of the diameter of the nozzle." To this I would emphatically take exception. Fig. 1 represents a vertical ideal section of tuyere, cruciblewalls and charge, immediately at the tuyere, in which the currents of air are represented, both in quantity and in direction, by the tortuous black-lines emanating from the nozzle-opening and passing through channels of the least resistance. As an electric current, flowing by various conductors to a common point, is carried in quantity inversely as the resistance of those conductors, so here the air ramifies through the most open cavities or channels, relatively little of it passing where the resistance due to fine materials is great. This figure represents the course of currents in the vertical plane only. As a matter of fact, they pass away in every plane, as opportunity offers. The effect of blocking or decreasing the area of the nozzleopening would certainly only decrease the quantity of air entering by that particular tuyere, without assisting penetration. The large channels (b, b, Fig. 1, for example) would still carry the larger part of the air, while again the smaller channels (a, a, a) would continue small and take no larger percentage of the air than before. These channels momentarily change, however, with the slow descent of the coke. Further on (p. 5), Mr. Hartman describes the dispersive effect of a single lump of fuel. He has only to conceive the entire spaces before the tuyere-nozzles as filled with such lumps, in order to parallel the condition of affairs I have just explained. It is where the large pieces of the charge come down, that the mass is the most open, and the blast passes most freely. On the other hand, wherever the fine ore collects combustion proceeds slowly, because of the smaller supply of air. The

Jan 1, 1899

By O. E. Kiessling

THIS announcement of the topics relating to production control, which the Committee hopes to have discussed at the February meeting, supplements the preliminary announcement published in the November number of MINING AND METALLURGY. In the previous article, the writer indicated the kaleide-scopic nature of the questions involved in obtaining better coordination in industry, and that, as a matter of practical expediency, the discussion in February would be limited to the more obvious difficulties in industry which need attention and to those questions which the Committee thinks would be of greatest interest to members of the Institute. But while practical considerations necessitate limiting the program, free discussion of all phases of the subject is urged by 'the Committee. In a preliminary consideration of the production control problem, there loom up two questions which have to be faced: (1) First, there is the question of the extra industrial capacity necessary to meet demand during the ordinary fluctuations of business, commonly characterized as `the "business cycle." Anyone who tries to formulate a program pertaining to productive capacity must decide whether he wishes to discuss the control of business cycles. While this question may eventually lend itself to treatment, the Committee does not feel that it can be considered at present with much profit. (2) The second question arises from the existence of over-stimulated capacity above and beyond peak demands in boom times. Discussion of this topic, it is felt, would be most fruitful. How to prevent capacity from being over-stimulated to an extent beyond any hope of possible demand is a

Jan 1, 1929

By Donald Warren, J. F. Libsch

HIS investigation originated as a result of a pre-vious experimental study' of the magnetic properties of Fe-Co alloys fabricated by the powder metallurgy technique. Densities of powder compacts prepared for the magnetics investigation varied from 7.45 to 7.70 g per cu cm or from 93 to 95 pct of the experimental value of 8.08 g per cu cm for a fused alloy of the same composition.' While this range of density is considered sufficiently high for most applications, the highest possible density is to be desired for maximum magnetic properties. By applying a technique similar to the one described above to a pure electrolytic iron powder, Rostoker³ was able to achieve a density of 7.895 g per cu cm, which is the highest density ever reported for sintered iron. While Rostoker's work involved the sintering of an elemental powder rather than a mixture, it was believed that higher densities should also have been obtained for alloys using the above technique because of the recoining operation and the high sintering temperature. Consequently, it was decided to investigate the various factors affecting the density of this alloy with the idea that such a study might lead to higher densities and, as a result, powder alloys having magnetic properties identical with those of the fused alloys. It was believed that the principal reason that near-theoretical densities for the powdered alloy were not obtained was the interference of gases with the normal sintering mechanism. When present during the sintering operation, gases can exert several harmful effects: they can remain on the particle surface and interfere with surface diffusion and plastic flow; they can be released and, under certain conditions, expand the void spaces through gas pressure; or they can remain trapped in the pores and exert a hydrostatic pressure that retards elimination of the pores. Jones,4 Rhines,5 Goetzel," and others have given the effect of gases in the sintering of powder compacts an extensive treatment. Among the more important sources of gases in the sintering process are dissolved gases, adsorbed gases, air entrapped during pressing, and gaseous products of chemical reactions. During sintering adsorbed gases are partly released at a relatively low temperature, while those gases entrapped during pressing cannot escape until their pressure is increased sufficiently through increasing temperature to expand the interpartjcle openings. The remaining adsorbed gases, gaseous reduction products, and dissolved gases produce a similar effect at the higher temperatures. If, in the sintering process, gas evolution occurs after the interpore channels have been sealed, an exaggerated expansion of the void spaces results. This is particularly true if the temperature is high enough for extensive plastic flow. In his fabrication of powder bars from tantalum, Balke7 had to consider the effect of adsorbed hydrogen and provide for its escape during sintering by limiting the compacting pressure to a maximum of 50 tons per sq in. The effect of gases entrapped during pressing was first noted by Trzebiatowski8 when he found that gold and silver powders decrease in density with increasing sintering temperature if pressed at 200 tsi, while they exhibit the usual increase when pressed at 40 tsi. Recent investigators9-11 have also noted that entrapped gases have an effect on the expansion of copper compacts during sintering. Proper provision for the escape of gaseous products of reduction must be made in order to avoid deleterious effects. Myers" states that in the sintering of electrolytic tantalum powder, the temperature was gradually raised to 2600°F with a pause at 2000°F to permit reduction of the oxides. Experimental Details For the present study, 50 pct Co-50 pct Fe compacts in the form of circular disks 1½ in. in diam and 0.15 in. thick were fabricated by the pressing and sintering of a mixture of the elemental powders. It was decided to follow the sintering process by means of liquid permeability measurements, because it was thought that such measurements might serve as a measure of relative pore sizes, as well as a possible indication of the point at which most of the interpore channels become sealed. However, since the permeability as measured by the flow of a liquid, such as ethylene glycol, does not give an absolute indication of the point where the pores have become isolated, a method for determining the percentage of pores connected to the surface was set up. As an additional cross check on the permeability measurements, metallographic methods were used to study the relative pore size. Finally, the property of ultimate interest, the density, was measured. Raw Materials: The powders used consisted of an annealed, 99.9 pct pure, —150 mesh grade of electrolytic iron powder, and a 98 pct pure, —200 mesh grade of reduced and comminuted cobalt powder. The cobalt powder was not further processed either by hydrogen reduction or annealing. The screen analyses for the iron and cobalt powders are given in Table I, while the chemical analyses for each type of powder are listed in Table 11. Table 111 gives the hydrogen loss measurements for the powders according to the M.P.A. Standard Method and for a higher temperature as well. Preparation of Compacts: Equal amounts of the elemental powders were mixed by rotation for 1 hr and then pressed into compacts approximately 0.15

Jan 1, 1952

By George T. Wickes

(Washington Meeting, May, 1905.) SEVERAL years ago, Mr. Robert A. Cook described and illustrated in our Transactions 1 a mechanical coke-drawer, patented in 1891 by Mr. Thomas Smith of the Thorncliff Iron Works, Sheffield, England, and first introduced in the United States in, 1896, at the coking-plant of the Latrobe Coal Co., Latrobe, Pa. This machine has not received any very extended application in this country, although it was successfully used in two places for a number of years. The present. paper describes a new and simpler machine, containing few wearing-parts capable of withstanding continued rough usage. Anything which tends to prolong the general use of bee-hive ovens will be welcome to those who are interested in cheapen¬ing the cost of producing coke in such ovens, especially if it provides satisfactory mechanical means, replacing the hard labor involved in drawing coke by hand with the old-fashioned ?duck bill.? The difficulty of finding efficient coke-drawers, especially during the summer season, and in the South, is notorious. Yet, notwithstanding the great improvements that have been made in retort coke-ovens, new bee-hive ovens are continually constructed; and a machine which will successfully compete with hand-drawing, and, at the same time, add to the efficiency of the bee-hive oven, seems to deserve notice. The machine here described was put in operation at the Frick Coal and Coke Co.'s plant, known as Continental No. 1, at Uniontown, Pa., in October, 1904, and is reported to have met successfully all the tests to which it has been subjected. This trial has demonstrated that one of these machines, equipped with an electric motor, and operated by one mart with an assistant, besides two men to " water down " the

Jul 1, 1905