Search Documents

By K. G. Wikle, W. W. Beaver

A general survey of the mechanical properties of commercially pure beryllium fabricated from powder by vacuum hot pressing and other consolidation methods is presented. The effect of fabrication method, grain size, strain rate, and directionality upon both room and elevated temperature tensile properties is reported. BERYLLIUM metal, in spite of its rather restricted use, has been the object of attention for many researchers in the past half century. However, such work was performed on special experimental lots of metal made in small quantities by a variety of reduction methods. Not until 1946 was there a substantial production of beryllium metal, and not until 1950 was there a steady production of a commercially standard beryllium in the United States. This output was both the result of a requirement of the Atomic Energy Commission for a high grade beryllium of consistent quality and the development of a powder metallurgy process, by the Brush Beryllium Co., known originally as Process Q, which yielded a fine grained beryllium suitable for fabrication. Because this powder metallurgy product, known as QMV, superceded other types of metal made previously and represents the great majority of beryllium in use today, it seems worthwhile to present the results of studies on the mechanical properties of this metal as currently made. To the design engineer and the metallurgist, beryllium has extremely interesting properties. It is as light as magnesium alloys while having a stiffness modulus 40 pct greater than steel and a strength-weight ratio superior to titanium and aluminum alloys and aircraft steels. The melting point is high, 1287°C (2348°F), and it has good corrosion resistance both in air and water. Also, it is highly transparent to X-rays and has good heat and electrical conductivity (electric conductivity is greater than 40 pct of Cu). To the atomic energy program beryllium is considered a valuable material because of its low neutron-capture cross section and high neutron-scattering cross section which make it a good moderator and reflector for the lower velocity neutrons. A major technical difficulty limiting the use of beryllium, especially in structural applications, has been its notch sensitivity and consequent room temperature brittleness. Kaufmann, Gordon, and Lillie1 have reported their work on the mechanical properties of beryllium performed from 1946 to 1950. They studied the room and elevated temperature properties of cast and extruded beryllium and extruded electrolytic flake, Table I. Cast and extruded alloys of 85 to 99 pct Be were tested also. They found that extruded metal developed good strength and appreciable ductility in the extrusion direction and that thermal treatment and alloying provided little improvement in mechanical properties. They concluded that preferred orientation and fine grain size were the means of obtaining optimum tensile properties in beryllium. Other investigators have measured and commented on one of the most striking mechanical properties of beryllium, namely, its abnormally low Poisson's ratio.2 Udy, Shaw, and Boulger3 presented the latest published survey on properties of beryllium but their information is based only on published data available before April 1949 and cites little information on metal fabricated by powder metallurgy

Jan 1, 1955

By A. W. Fahrenwald

CELL depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence-i.e., the depth in the pulp at which the impeller is required to produce aeration. THE FLOTATION MACHINE A COMPRESSOR A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure[t] (14.7 lb. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 lb. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 lb. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 [-] 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 [=] 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the finer, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. THE FLOTATION MACHINE AS A PUMP Since, in impeller machines that rely upon their own operation to produce aeration, pulp passes through the im-

Jan 1, 1946

By Herbert Hoover

BOTH the directors of industry and your leaders have made great progress toward a new and common . ground in economic conceptions, which, I am confident, has had a profound effect upon our economic progress during the last few years. That is the conception that industry must be constantly renovated by scientific research and invention; that labor welcomes those labor-saving devices; that labor gives its full and unrestricted effort to reduce costs by the use of these machines and methods; that the savings from these reduced costs shall be shared among labor, employer and the consumer.

Jan 1, 1930

By Harold V. Pearce

THE plant of the Boston and Colorado Smelting Company, at Argo, Colo., has not received special notice in technical or scientific publications for some time past. Dr. Peters' described the development of the reverberatory furnace used at Argo, but he dealt almost exclusively with the increase in size and the corresponding gain in capacity. Since the time of his description the changed conditions have led to a modification of the former smelting practice, and this modification forms the basis of the present paper. No claim is made for personal originality in connection with these improvements, in fact, I expressly disclaim any such intention, since nearly every successful step in the development of the process now used at Argo has been suggested by Dr. Richard Pearce at various times during the past 12 years, though perhaps in a different manner of exe¬cution. These changes would undoubtedly have been made before, were it not that many problems of greater metallurgical importance and momentarily of more urgent need thus had to be solved. At the time to which I refer, economic conditions demanded mainly an increase of capacity. Moreover, the determination and placing of exact losses in smelting were not so imperative as they now are. About three years ago, the time of my appointment to the - management of. the works of the Boston and Colorado Smelting Co., the great decline in the price of copper occurred; the Argo plant, in common with all others engaged in the copper-industry, lost heavily in the market-value of the stocks on hand of ore and furnace-products. Added to this was the unfortunate circumstance that the copper-supply of the Argo plant from general sources began to dwindle; in fact, it almost entirely ceased. About this time the smelting-plants in the west-

Mar 1, 1905

By W. C. MENDENHALL

THE problem of maintaining the mining industry is two-fold; finding new supplies in the face of increasing difficulties, and making such advances in the arts of extraction and preparation as to use supplies of lower grade. Progress in mining and reduction methods and in transportation makes ore today of that which was waste yesterday. These are the fields of the metallurgists and the transportation engineers. The geologists and mining engineers must work together on the problem of ore finding. As the old prospector fades from the scene, men with equal hardihood and patience and equal power to meet the physical obstacles which confront the seeker after ore, must take his place, armed with all that has been learned from human experience about the causes, the controlling conditions, the indications, and hiding places of the metals. Such a seeker is dealing with some of the most complex and obscure of natural phenomena. In nature's laboratory, tremendous forces are at work. Tempera-

Jan 1, 1926

By H. E. Dunn, C. M. Cosman, J. H. Brennan

Up to the beginning of World War I, the American ferro-alloy industry was in its infancy and largely dependent on Europe. During that War, capacity was over expanded. Later recovery and commercial and scientific development have resulted in an industry which in 1957 produced 1.8 million tons of ferro-alloys. THE ferro-alloy industry is today an important element of the industrial structure of the United States. Its output is valued at almost half a billion dollars annually and its products are basic not only to National defense but also to the peacetime standard of living. This has not always been so. The ferro-alloy industry from late in the last century has grown from small beginnings, nurtured by the demand for stronger, tougher materials; by the search for steels capable of absorbing severe impact loads and resisting corrosive media and high temperatures; and also by the need for electrical and electronic specialties. Conversely, the ferro-alloy industry has grown because it developed improved steels and alloys by extensive research, and because it was able to show to steel makers the advantages accruing from the more extensive and the more economical use of alloying elements. The industry has grown in scope from producing a few grades of ferro-alloys of the more common metals-manganese, chromium, vanadium, silicon, titanium, tungsten, and molybdenum-until there are today some 150 compositions of ferro-alloys available to the steel maker, including such elements as columbium, zirconium, and boron. In 1912 the industry produced 360,000 tons of alloys valued at about $12,000,000, while 1957 production figures show an output of 1.8 million tons worth $440,000,000. In the United States, the history of an industry is largely the history of the companies making up this industry; hence, this paper will briefly trace the development of the most important ferro-alloy-producing companies. Quite varied have been the reasons that caused the different companies to move into the ferro-alloy field; the Willson Aluminum Co., seeking methods of producing aluminum, succeeded with the production of calcium carbide, and their developing electric furnace skills led them to the production of ferro-silicon and ferrochromium alloys. Willson was the predecessor of the Electro Metallurgical Co. of Union Carbide. Two Pittsburgh undertakers, interested in vanadium as an alloying agent for steel, set about to find a mine and, ranging as far as Peru, fathered American Vanadium Co., the predecessor of Vanadium Corp. of America Experiments of the

Jan 1, 1961

In 1974, iron pellet production in the Great Lakes region reached the 53-million-tpy level, accounting for more than 88% of the nation's pellet production. By 1978, pellet output from the Great Lakes district will climb to at least 78 million tpy. To achieve this 50% increase in output, the US iron and steel industry is investing at least $1.25 billion in new mines and pelletizing plants, mostly in Minnesota and Michigan. The biggest effort is concentrated in the Mesabi Range of Minnesota, the heart of the US steel industry's major iron ore source: here, plans for two new taconite plants-one by Hibbing Taconite Co., and the other by Inland Steel Mining Co.-and three major expansions of existing facilities are already under way to boost Minnesota's total iron pellet capacity from the current 41.2 million tpy to 65 million tpy by 1978. The facilities being expanded are those of US Steel Corp. (Minntac operations), Eveleth Taconite Co., and National Steel Pellet Co.

Jan 11, 1975

By T. P. Chen, F. W. Bowdish

Studies made with a captive bubble apparatus on the sulfidization and collection by amyl xanthate of true chrysocolla specimens have defined the ranges of pH value and sulfide concentration which permit contact between the bubble and the mineral surface. Titanium compounds were the most effective of the materials found to activate the sulfidization of chrysocolla. With titanium activation, the contact angles and the ranges of pH value and sulfide wncentration giving bubble contact were all increased. Chrysocolla ores were concentrated by flotation. Chrysocolla ores occur at many localities in grade and quantity sufficient to make mining and millin feasible, but no satisfactory method of concentratio has been found. Although chrysocolla may be leached with acid, only those ores without acid-consuming gangue may be leached economically. Because of its potential importance, a study of the conditions nece sary for flotation of chrysocolla has been carried ou The literature contains a few references to flotation of chrysocolla. Two methods were developed by the U. S. Bureau of Mines.1,2 The first consisted of a fatty acid soap and a high xanthate as collectors of chrysocolla from a synthetic ore, while the second involved the use of hydrogen sulfide and xanthate. Ludt and DeWitt3 demonstrated the difference in adsorptive powers of chrysocolla and quartz for bas triphenyl methane dyes and suggested the use of butyl, hexyl or octyl-substituted malachite green as collector. Jackel4 emphasized the effects of combin tions of reagents such as Aerofloat 31, pine oil, and Reagents 404 and 425 with sodium sulfide and zinc hydrosulfite as conditioning agents. Although he reported recoveries of 89% from a synthetic ore and 98% from a natural ore containing azurite, malachite, chalcopyrite and chrysocolla, careful application of Jackel's method to chrysocolla from Tyrone, N.M., failed to give a high recovery. MATERIALS AND TECHNIQUE Samples from Inspiration, Ariz., and Tyrone and Magdalena, N. M., were used for experimentation and verified as true chrysocolla by leaching tests, specific gravity tests and X-ray diffraction. Chrysocolla does not dissolve at pH 4, although malachite and azurite do. Chrysocolla is about half as dense as the copper carbonates. X-ray diffraction analyses by the powder camera method confirmed the samples as true chrysocolla. A captive bubble apparatus, which cast an enlarged image of the air bubble and the mineral surface upon a screen, was used to check on the character of the surfaces. The specimens were prepared by grinding a flat surface on a glass plate using fine abrasive; then they were washed and kept in distilled water until they were to be treated with reagents. Before each reagent treatment, the specimen was carefully checked for cleanliness in the captive bubble apparatus. It was assumed that the surface was clean if, after fine grinding and washing of the specimen, the bubble would not stick. Specimens were handled with glass forceps, and precautions were taken to avoid contamination of the mineral surfaces. Contact angle measurements were carefully made several times on each treated specimen to obtain reliable average values. EFFECT OF pH VALUE AND SODIUM SULFIDE CONCENTRATION In each experiment, a specimen with a freshly ground surface was immersed for 10 min in a solution of sodium sulfide, washed and immersed for 15 min in a solution containing 30 mg per 1 of potassium amyl xanthate. The specimen was then washed again in distilled water and tested for contact angle in the captive bubble apparatus while submerged in distilled water. In this series of experiments, the pH of the sulfidizing solution was varied from 3 to 7, and the concentration of sodium sulfide, containing 60% Na2S, was varied from 50 to 650 mg per 1. Many combinations of pH value and sulfide concentration resulted in no contact between the bubble and the surface, but over a limited range of conditions, contact angles varying from 24ºto 52ºwere obtained. The data in Fig. 1 show sulfidization conditions that lead to bubble contact and those that do not. The region of contact is surprisingly small, which may indicate why flotation of chrysocolla involving sulfidization has proven so difficult in practice. Several features of the system are illustrated in Fig. 1. In the region between pH values of 4 and 6 with sodium sulfide concentrations below about 350

Jan 1, 1963

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

By C. W. Bildt

During many years of service in the iron and steel industry I have frequently found, as have also many other engineers, that the common devices used for feeding coal into gas-producers are not what they ought to be in order to secure the best economy. The hopper-and-cone so generally used is familiar to all, and a brief study of its action will surely satisfy everybody that this device has several serious faults. In the first place, the charging is intermittent, and depends entirely upon an attendant. When the hopper is frequently emptied, it may work fairly well, but even then it suddeinly discharges into the hot producers a large body of coal, which is often violently converted into gas that rushes into the furnace, and, as the damper for the combustion-air cannot be regulated every time the producer is charged, there will be an excess of gas, which goes up the chimney unburned. Between the chargings the quantity of gas generated decreases, and there will often be an excess of air in the furnace,

Jan 1, 1899

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators 1-5 have noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilities6 and by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported' to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of this portion is shown in Table I and an approximate mineralogical analysis is shown in Table II. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of -6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1952

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

By AIME AIME

THE best meeting ever held, was the opinion expressed by a number of those who attended the annual meeting of the Institute in New York, Feb. 18 to 21, and there was an atmosphere of friendliness and good fellowship about it that fully justified the feeling. In numbers it was not quite so large as last year and unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger, in respect to numbers, than that held in 1928, which was only made possible by the circumstance that the eighth floor of the building happened to be, temporarily vacant at the time. The number of rooms available for -sessions that were provided when the building was built long ago proved inadequate, and it is only by the expedient of obtaining the temporary use of the board and committee rooms of other societies that it is possible to arrange for the over 40 sessions that must be spread over the four days of the meeting. The-fifth floor, where. a buffet lunch is served each-day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size.

Jan 1, 1929

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By Gilbert P. Moore

The production of petroleum in Argentina during 1932 was greater than in any preceding year. The total amount produced was 13,012,-756 bbl. This figure represents a decided increase in the production of oil in Argentina and can be attributed largely to the increased activities of the Royal Dutch operations at Kilometer 27 in the Comodoro Rivadavia district and those of the Standard Oil Co. of Argentina in the Salta region. Production from the Royal Dutch wells amounted to considerably more than 10,000 bbl. per day over quite a long period during the year. Of the 13,012,756 bbl. of oil produced during 1932, the Government Agency (Y. P. F.) was responsible for some 5,578,954 bbl., while 7,433,-802 bbl. were produced by private companies. Although in 1930 the Y. P. F. produced about 55 per cent of the total production and in 1930 50 per cent of the total, in 1932 its production had fallen to about 42 1/2 per cent of the total. This decrease in the proportion produced by the Y. P. F. was not due to a decrease in its production but to the decided increase in the production of private companies, particularly those two whose names are given above. One new discovery was recorded during the year. This was a well drilled by the Y. P. F. at Cacheuta in the province of Mendoza which came in pumping 80 bbl. of 15" gravity oil from a depth of 673 meters. This well was completed at approximately the same time that the provincial government of Mendoza granted a concession to the Y. P. F. and declared the whole province as a reserve in which no concessions may be granted for a period of 10 years. Under these conditions, the federally operated Y. P. F. will have no competition in the Cacheuta area from private companies such as they have in the other three fields of the republic. The Y. P. F. wildcat west of Comodoro Rivadavia at Pampa Maria Santissima on the Rio Senguerr was completed as a dry hole during 1932. This we11 was reported as a producer in 1930 by persons returning to this country from Argentina but it appears that they had been misinformed. The site of this test has been abandoned and a new location made north of the Rio Senguerr.

Jan 1, 1933

By R. E. Boehler, N. C. Ludwig

At Buffington Station, Gary, Ind., Universal Atlas Cement operates fourteen 8 x 101/2 x 155-ft cement kilns in mill 6 and two 11 x 360-ft kilns in the Harbor plant. The No. 11 and 12 kilns in mill 6 are equipped with Manitowac recuperator sections. This report describes studies in measuring exterior shell temperatures on several of these kilns and the development of a traveling radiation pyrometer with certain novel features. Preliminary Work: At first various temperature-sensing devices were placed on the steel shell: 1) crayons with calibrated melting points, 2) colored paints with temperature-calibrated pigments, 3) aluminum paints with temperature-calibrated binders, and 4) metal-stem dial thermometers. The colored paints and aluminum paints failed to indicate the temperatures correctly. The crayons and thermometers did indicate fairly correct temperatures, but it proved impossible to apply enough of these on the shell to detect all the potential areas where hot spots might develop. Furthermore, considerable labor was required to apply these sensors and read the temperatures. Consequently no further work was done with these devices. Formation of Hot Spots: In the burning or clinker-ing zone of a cement kiln, the thickness of the protective coating and thickness of the brick govern the amount of heat transmitted to the steel kiln shell. Usually the protective coating consists of 4 to 8 in. of fused cement clinker. The formation of a hot spot is usually caused by loss of coating? that is, localized areas of the coating become thin or fall away from the refractory. This is generally caused by excessive temperature in the burning zone over a fairly long period of time. It may also be caused by a sudden thermal change in the burning zone. Variations in raw feed composition and in feed rate require changes in the fuel and air rates, and when these are not appropriately altered, conditions may develop in the kiln that will result in loss of coating. Luminescence on the kiln shell indicates that a hot spot has developed to a point that usually alters the refractory's thermal conductivity properties. When this thermal weakness zone occurs in the burning zone of the kiln, constant vigilance is required to protect it by maintaining proper coating. Even so, it has been the writers' experience that within a period of several days to about four weeks the hot spot usually recurs with greater severity. This necessitates shutting down the kiln and re-bricking the affected area. One of the prerequisites of a good burnerman is the ability to maintain a protective coating despite the many variables in operation. When he knows that it is getting thin or that an area has dropped off, he reduces the firing rate and kiln speed and brings feed into the affected area in an effort to rebuild the coating. But when powdered fuel is burned, the atmosphere of the kiln may prevent the burnerman's observing the condition of the coating closely at all times without taking off the fire. It is not considered good practice to do this frequently, as it imposes a thermal shock on the coating and upsets operation of the kiln. To help the burnerman scan the shell of the kiln along the burning zone, therefore, a radiation pyrometer, connected to a potentiometric recorder, was mounted on a slowly moving steel cable. The theory of operation, construction details, and adaptability of the radiation pyrometer are included in an excellent monograph' and also in a textbook.' Shell temperatures of the Atlas Cement kilns were measured with a Brown Instruments Div. low intermediate range Radiamatic unit, of range 200" to 1200°F, and a circular chart Electronik potentio-metric recorder, of range 500" to 1000°F. In Bulletin 59095M the supplier publishes standard calibration data (millivolts vs degrees Fahrenheit) for this radiation pyrometer, These data, however, apply only to flat surfaces having emissivities of unity. Calibration of Radiation Pyrometer for Use on Curved Surfaces: When applied to surface temperature measurements, the radiation pyrometer reading depends on the nature of the surface, the material of which it is composed, and also to some extent on the temperature of the surroundings. Although the present radiation pyrometer is designed to give a calibrated response under ideal (black body) conditions when used commercially, it must be calibrated empirically. The calibration procedure, given below, follows that described by Dike (Ref. 1, pp. 38-39). Calibration tests on plane and curved surfaces showed that the response of the radiation pyrometer was very

Jan 1, 1961

By Paul W. Zimmer, Carl E. Dutton

Iron ore in the Menominee district is mined from two iron-formations of middle Precambrian age. The older formation is present in the northeastern part; is composed mainly of hematite, magnetite, quartz, and minor silicates; and contains about 34 per cent iron. The rock has been so coarsened by meta- morphism that concentration of magnetite and hematite is feasib!e, and pellets containing more than 60 per cent iron are being produced. The older formation is also present in the southeastern part where it has 1:een only slightly metamorphosed. Ore containing more than 50 per cent iron was formerly mined from local residual concentrations of iron oxides from which silica had been sufficiently leached, or replaced by iron oxide, or affected by combinations of these processes. The younger iron-formation occurs in the western part of the district and, if unaltered, is interlayered siderite and chert. The ore in this area also contains more than 50 per cent iron and formed as local residual concentrations but in two stages. The siderite was converted to iron oxides (hematite and "limonite"), and silica was contemporaneously or subsequently removed by leaching, or replacement, or combinations of these processes.

Jan 1, 1968

By G. E. McElroy

Much attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for W D V equal values of the product where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and p = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Reynolds1 more than 40 years ago. Later, Rayleigh2 amplified the theory which has been conclusively proved for small pipes by the experiments of Stanton and Panne13 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory, results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,6 has outlined the application of this theory to mine-air flow and recent English experiments6 on the resistance of a timbered mine airway have been expressed in this form.

Jan 1, 1927

An extended investigation by the chief engineer of the Bureau of Mines shows that North Dakota has immense beds of lignite. War conditions have stimulated the use of North Dakota lignite until it is now being used at the rate of 1,000,000 tons annually. This North Dakota lignite is coming into extensive local use and considerable of it is being shipped to various parts of the state. The great problem at the present time is to find a market for the gas, which is the principal-by-product of lignite preparation. Bureau of Mines specialists will complete their reports of the studies of lignite in this country and will then make a recommendation as to the lignite field which is best suited for the establishment of the proposed Government's experimental plant. "Broken eggs cannot be mended."-(Lincoln.) Neither can "cashed in" War Saving Stamps grow to their maturity value.

Jan 8, 1919

By F. W. Jessen, James N. Howell

INTRODUCTION The determination of cloud points has to date been limited to rather transparent oils, visual observation of the formation of a solid phase being the criterion for the standard ASTM D 97-47 method. The need for a quiclc and simple method for determining cloud points under dynamic conditions for opaque crude oils became necessary in a study of fundamental aspects of paraffin deposition from crude oils. PREVIOUS WORK The determination of cloud points in opaque oils by viscosity temperature curves is fairly new, Young' described a method employing the capillary tube principle. No information exists relative to the determination of cloud points of crude or refined oils under dynamic conditions. Shock' noticed that deposition of paraffin from crude oils took place at temperatures at or below the temperature at which a sharp inflection point occurred in the viscosity-temperature curve. This observation indicates a possible correlation between this temperature and the cloud point of the crude oil. Reistle and Vietti1 have reported that when crude oils containing small amounts of asphaltic materials were heated to temperatures sufficiently high to solubilize these materials and immediately cooled the pour point of the crude oil was lowered as much as 70°F. Sachanen\ asribes this effect to the action of colloidal asphaltenes in preventing the formation of the crystalline structure necessary to maintain the oil in a rigid state. At high temperatures, asphaltenes are peptized, and the paraffin crystals formed at these temperatures adsorb the colloidal asphaltenes on their surface thereby hindering further growth of the crystals. Reistle" found, however, that such heating and cooling of crude oils had no effect upon the cloud points. This latter work dealt with a crude oil of fixed composition, and the question immediately arises as to the effect of varying the concentration of asphaltic materials on the cloud point. APPARATUS AND PROCEDURE All viscosity measurements were made with a Bendix Ultra-Viscoson. The Bendix Ultra-Viscoson, which consists of a vibrating probe and an electronic computer. measures viscosity by exciting a thin alloy steel blade on the end of a probe by short electrical pulses in damped oscillation at 28 kilocycles. The blade vibrates longitudinally with an amplilude of less than 55 micron or 20 millionths of an inch. Energy to protlucc this excitation is generated in he computer and transferred to the probe through the connecting cable. The oscillating blade is magnetostric-tive, i.e., it is capable of transforming electrical energy to mechanical energy in the ultrasonic range. Ultrasonic waves are produced in the material surrounding the blade by the oscillating motion of the blade causing layers of the material to slip back and forth over one another at a known frequency. The electronic computer calculates the energy required to produce the sliding motion which is in turn proportional to the viscosity of the material. Actual values of viscosity times density (centi-poise X grams/cc) are indicated on the computer and a continuous D-C signal is provided which is fed into a type 153 Electronic Recorder (manufactured by Brown Instruments Div. of Minneapolis-Honeywell Regulator Co.) The liquid sample container was fabricated from a Lucite cylinder and jacketed by a Luicite water bath. Early experiments using glass and steel sample containers were not satisfactory. since the Ultra-Viscoson was apparently affected by the alterzltion of the magnetic fields surrounding the probe by stresses set LIP in the glass and steel as it cooled. The procedure for determining viscosity-temperature curves was relatively simple. The temperature ot the sample was raised sufficiently high to solubilize all paraffin and asphalts present. After heating, the oil sample was immediately transferred

Jan 1, 1957