Search Documents

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By L. A. Wilson, P. J. Root

The relative costs of heating a reservoir by steam injection and by combustion have been examined. The comparison was based on a model similar to that proposed by Chu.' The cost of boiler feed water, the price of fuel, pressure and plant capacity were parameters in determin-ing the costs of air compression and steam generation. The analyses compare the cost of heating to the same radius by the two methods. Results suggest that the two primary factors for comparison are the price of fuel and the amount of crude burned during underground combustion. The cost of fuel has a greater effect on the cost of heat from steam than it does on its cost by combustion. As a result, analyses indicate that when the price of fuel is low, steam may be unequivocally cheaper than air. The influence of heat loss is such, however, that as the heated radius increases combustion becomes relatively more competitive depending upon the amount of crude burned. This implies that steam may be cheaper for small stimulation jobs (huff and puff) but combustion may be more economically attractive for heating large areas (flooding). INTRODUCTION Use of thermal methods of recovery is an accepted fact today. After an induction period of several years, processes are being widely used that involve reservoir heating to augment recovery. Of the several techniques, steam injection and forward combustion appear to be destined to dominate the field. Although the objectives of both are the same, the basic differences between generating heat in situ and injecting heat after surface generation influence the cost in different ways. This study compares the cost of heating a reservoir either by steam injection or by forward combustion. There has been no consideration of recovery. Presumably, recovery from the swept region would be high in either case. The sole consideration was the cost of heating to the same radial distance by either process. PROCEDURE THE MODEL The basis for comparison was a mathematical model similar to that used by Chu' for combustion. The model simulates a radial heat wave in two-dimensional cylindricaI coordinates. It includes heat generation, conduction and convection within the reservoir and conduction in the bounding formations. Thus, heat losses from the formation are considered. Three significant modifications were made. 1. Equal logarithmic increments rather than equal increments were used for the mesh spacing in the r direction. By this technique large distances were simulated with relatively few mesh spaces. 2. A backward difference approximation to the convection term was used to avoid troublesome oscillations which result from a central difference approximation when the convection term is large. 3. The radial increments of the combustion zone motion were not necessarily uniquely related to the mesh configuration. The cumbersome step function introduced by the heat of vaporization of steam was circumvented by assuming the enthalpy of the steam to be a linear function of temperature between reservoir temperature and steam temperature. This is equivalent to assuming an average heat capacity numerically equal to the difference between the enthalpy of saturated steam and the enthalpy of water at reservoir temperature divided by the difference between the two temperatures. Heat losses obtained by this model are in essential agreement with those obtained by the analytical solution of Rubenshtein.' A detailed description of the model is presented in the Appendix. Using the model, the times required to heat to particular radial distances were obtained as a function of injection rate and other physical parameters. For the steam case, injected fluid was assumed to be saturated steam at pressures of either 500, 1,000 or 1,500 psia. The corresponding temperatures are 467, 544 and 596F, respectively. Thickness ranged from 10 to 50 ft and injection rate ranged from 100,000 to 1 million Ib/D. Reservoir and overburden temperatures at the injection well were assumed to be that of saturated steam at the injection pressure. The effect of maintaining the overburden temperature at the well at a different temperature (initial reservoir temperature) was examined with no significant change in behavior. The influence of wellbore heat losses for the steam case was determined in the following manner. The rates of heat loss as a function of time were estimated using an approach similar to that suggested by Ramey." he data were based on injection through 2%-in. tubing in 7-in. casing. Integration of these data over the entire iniection period yielded the total heat loss. Total heat losses were then corrected to their equivalents in steam (this number resulted from dividing the total heat loss by the latent heat). This was considered additional steam required to accomplish the reservoir heating and the total cost was increased accordingly.

Jan 1, 1967

By THOMAS S. MENNIE

ON GORE Mountain, about four and a half miles, southwest of the village of North Creek, Warren Co., N. Y., are the Barton Mines. Here is the largest known deposit of garnet in the world. This property is owned by H. H. Barton &: Son Co., of Philadelphia, and is being worked under lease by Barton Mines Corpn. North Creek is the terminus of the branch of the Delaware and Hudson R..R., which runs into the

Jan 1, 1925

By Thomas T., Read

ANY discussion of State-supported schools of mining and A metallurgy needs to be prefaced by a definition, since the first school to offer a mining curriculum, the Pennsylvania Polytechnic College, was established by a grant from the State. But, so far as can be determined, it received no further State support. It would be tiresome to go into precise details,. and it will be enough to stipulate that by State schools are meant those which derive their main financial support from regular appropriations made by a State legislature. The University of Michigan was the first of these to offer a mineral industry curriculum; its story, as well as those of Wisconsin and Illinois, has been related in the preceding chapter.* Arranging the others in chronological order involves making a decision as to what weight to attach to plans for giving instruction, as contrasted with its , effective initiation. This may appropriately be illustrated by the history of mineral industry education in California. California Among those who came to California in 1849 and the following years were many New Englanders who had a keen interest in education. Some of them, mostly Congregationalists and Presbyterians, sought to establish a school of higher education around San Francisco Bay and eventually succeeded in opening the "Scientific and Classical School at Contra Costa' in Oakland, at Broadway and 5th St., on June 20, 1853. This prospered so well that it was chartered by the State as the "College of California" on April, 13, 1855. Developing so rapidly that its quarters became cramped, in 1864 it not only bought a tract of

Jan 1, 1941

Adolph Greiner, Seraing, Belgium:—I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have corrected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent. was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix 11. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p. in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. Tom WEstGarth, Middlesbrough, England :—My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by British engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have become quite ordinary motors for a good many purposes. It was at first thought that gas-engines were troublesome, and ill-

Jan 1, 1907

By W. M. Ross

AMONG the comparatively few A radical changes in mining equipment in recent years is the introduction and use to an ever greater degree of detachable bits for rock drills. Just how great the possible field for economic application of this innovation is, and to what ex- tent detachable bits are used instead of the conventional type of drill steel, are matters of conjecture. Just as a rough approximation, one might conceive that at least three-quarters of the drilling done in mines today could better be performed by steel with detachable bits, instead of only about one-quarter as at present.

Jan 1, 1939

By AIME AIME

Gentlemen, we have ten questions on our list and a number of us here probably have other questions to ask. Therefore, we arc going to allocate the time to these different questions so that we will try to be finished by 4:30; from then until 5 o'clock, if any of you have any questions on subjects not related, you will be free to ask them. Mr. Morton and I have changed the order of the questions. Instead of what is now first, we have put No. 3 first, progress on basic-roof construction, inasmuch as we feel that it is quite important. At this time, H. S. Robertson, of Harbison-Walker, is going to give you a short talk, with slides, on what has been done to date on this subject.

Jan 1, 1940

By Frank B. McKune

This is something new in my life. A lot of you men here today I do not know, and some I do know. So if you have any remarks to make, I wish you would give your name and the name of your company. This is the first Acid Meeting which has been held under the auspices of the National Open-Hearth Steel Conference, and I hope it is a success. Whether it is a success or not depends entirely upon the support we get. If it does get good support, I have the idea it will be continued as a regular feature of the National Open-Hearth Steel Conference. We all think we have pretty good practices. But we can all learn and I hope that you, gentlemen, who take issue with the things someone else has said will stand up and give your opinions. Otherwise, the meeting will fall rather flat, and we won't get a great deal out of it; and there will not be enough interest shown by the National Committee to continue to place the meeting on the regular yearly program.

Jan 1, 1940

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By John B. Miles

THE present period of depression in the iron industry, with the resultant close approximation of the cost of production to the selling-price of pig-iron, should make the discussion of this subject at this time not only interesting but, profitable. It is possible that it may result, in the collection of data, which when added to those set forth in this paper will clearly indicate the influence of the rate. of driving a blast-furnace upon its fuel-economy. The question is not whether an excessive rate of driving (meaning a rate definitely in excess of the average rate in the United States) results in, an increase in the fuel-consumption, but rather whether a rate considerably less than the average does not result in a marked decrease in the fuel-consumption. The commercial and metallurgical sides of. this problem must be kept separate. With a large margin between the cost of production and the selling-price of pig-iron, and a plant already in operation, it is frequently profitable to sacrifice a couple of hundred pounds of fuel per ton of pig-iron in order to secure the greater gross profits resulting from a larger tonnage. When this margin decreases with a plant in operation, or when the determination of the size of a new furnace intended for a certain production . confronts the management, a clear understanding of the effect of the rate of driving upon fuel-economy becomes necessary. If it be granted that slow driving leads to low fuel-consumption, it should he borne in mind in the design of a new plant for the production of a certain tonnage that the adoption of an economical rate of driving increases only the size of the furnace proper, whereas, due to the decrease in quantity of blast required on account of the decrease in fuel burned, the stoves, the blowing-engines, the boilers and the piping may be de-

Sep 1, 1908

By AIME AIME

THE official opening at the 134th general meeting of the Institute was held on Oct. 6, but it was prefaced by two round table conferences on Oct. 5. The open-hearth group held the fourth of their semi-annual conferences at the William Penn Hotel, devoting the morning session to discussing a paper by R. L. Cain on the "Manufacture of Forging Steel by the Open-hearth Process," and the afternoon to discussing P. H. Shaeffer's paper on the open-hearth charge. At the Bureau of Mines, a round table conference on the combustibility of coke was held on Tuesday morning, and the afternoon was devoted to a similar conference on the testing of coke. The formal opening session of the meeting assembled in the Music Hall of Carnegie Institute at 10.30 a. m. Graham Bright, chairman of the Pittsburgh Section; called the meeting to order and presided. President Taylor welcomed the visiting members and guests to his home city and reviewed briefly the advancement of mining in the past half century during which, for ex- ample, the coal output had increased from 53,280,000 tons to 523,357,000 tons per year. He emphasized the important part Pennsylvania played in mining and brought out the principal changes that had taken place in methods. In part, his remarks were as follows: The centennial year, 1876, found the coal business of. this country, as a whole, producing 53,280,000 tons, of which amount the bituminous mines of this State yielded 24 per cent. In 1925, this country produced 523,357,000 tons of coal, of which Pennsylvania produced 24 per cent.

Jan 1, 1926

By W. R. Ingalls

THE following chronology presents the history of lead-mining in the United States in a brief form and is a useful reference in connection with the statistics of production 1621. Lead was mined and smelted near Falling Creek, Va., to supply the local demand for bullets and shot. This was the first mining and smelting of lead in what is now the United States. 1632. In a report made on the minerals of New England, lead-ore is mentioned. (Bishop, I., 470.) 1650. Supposed beginning of mining by Jesuits in Pima county, Ariz. 1651. Grant of lead-mine at Middletown, Conn., to Gov. John Winthrop.

Jan 9, 1907

By HOWARND N. EAVENSON

THE year 1930 resembled the preceding one in the coal industry in continuing the era of falling prices and 'of the abandonment of unprofitable mines. Practically all coal prices fell, and in the steam sizes during the last half of the year this was particularly true, due to the small industrial demand. No new mines of any size were opened in the bituminous coal industry, but there was a steady increase in the number of cleaning plants of all kinds built in all fields. It is estimated that at least nine million tons per year were added to the previous total of washed coal. The largest washing plant started during the year was that of the Buckeye Coal Co., at Nemacolin, Pa., with a capacity of 650 tons per hour. Fig. 1 shows - the mixing-bin, conveyor galleries, washing-plant and skip hoist, and Fig. 2 the 120-ft. Dorr thickener for collecting the 48-mesh material from the wash water. Dryers are used for drying the steam coal product. The following statement by J. R. Campbell shows the effect of cleaning on Pittsburgh coal in Greene County: "With the advent of the 650-t.p.h. efficient washing plant in Greene County at the Nemacolin mine of the Buckeye Coal Co., it has undoubtedly been demonstrated that the potential coking-metallurgical coals of the county can be brought within the pale of the highest grade high-volatile coals for steel manufacture. A few months' operation indicates that 9% per cent ash in the raw coal can be easily reduced to under 7 per cent ash in the washed coal and the sulfur from 1.60 per cent in the run of mine to 1.20 per cent sulfur in the washed coal.

Jan 1, 1931

By James K. Richardson

STATISTICAL evidence shows that continued efforts made by Government and industry to make mining safer during the last two decades have had most favorable results. In the copper-mining industry an accident frequency of 146 per million man-hours worked in 1925 dropped 71 per cent by 1945 to 43. This downward trend was relatively consistent except for a high period in 1937 which was probably due to a resumption of large-scale operation with many untrained miners. The iron-mining industry showed a similar trend, but at the relatively lower accident frequency of 66, which dropped to 24 in 1945. The close relationship between the steel and iron-mining industries may be one reason for the lower accident frequencies, because the steel industry is noted for its greater recognition of the fact that safe working conditions are an important part of labor-management relations.

Jan 1, 1948

By Eugene McAuliffe

THE heavy shrinkage in the production of bituminous coal has reflected adversely in the matter of tonnage produced by stripping arid mechanical loading machinery. The purchase of stripping and underground loading equipment has likewise been circumscribed. How- .ever a growing percentage of bituminous coal is being loaded by stripping and mechanical loading machinery. This situation is due to the fact that numerous strip pits were able to operate in Illinois and Indiana when under- cover mines were subjected to labor interference, a further advantage gained by their ability to produce and market coal at a price below that of the undercover mines. The mines equipped with mechanical loading. apparatus have enjoyed more continued operation for the double reason that the companies using coal-loading machinery are, generally speaking, more substantial and in better financial condition than many of the smaller properties who maintain hand-loading methods, and the market advantage due to lower production costs also reflects to the advantage of the undercover mines using mechanical loading equipment. Where a number of mines are con- trolled by one company, those not equipped with loading machinery and suffering from higher producing costs have often been closed, with the available tonnage concentrated in the more modernly equipped mines.

Jan 1, 1933

By H. Foster Bain

Steel for any large structure must be imported, the Hanyang works being entirely unable to supply local demand. The United States Steel Products Co. has warehouses and small stocks at Shanghai and at normal times there are heavy importations from Europe. It is difficult to obtain any accurate index of prices, but comparison of customs valuations with Pittsburgh quotations shows angles, bars and plates to have averaged $10 gold per ton higher in China in 1914, while on galvanized and tinned plates the excess was- $38 per ton. The margin since has been greater. Previous to the war little machinery was manufactured in China. There were shipyards at Shanghai and at Hong Kong which built a small number of engines, and small foundry and repair works are found at a number of ports. Their capacity was limited and the difficulties and delays incident to transport in China so numerous that in practice every important mine has a small foundry, boiler works, and machine shop. This must be taken into account in plans for work in the country. While skilled workmen can be found it is to be noted that most of them have been trained

Jan 1, 1921

By M. D. Cooper

IN spite of the uncertainty in the bituminous coal industry during 1933, progress worth recording has been made. Along with other industries, coal has felt the effects of business stagnation, but even in the worst weeks of the past four years, .the total production of bituminous coal in the United States was seldom less than half the production in some of the best weeks of the more prosperous years, a record better than that of many industries. However, the competition of other fuels and sources of power, together with the increased efficiency in the use of coal, has brought anxiety to producers. This has resulted in pressure for reduction of costs, not always by the wisest means. On the other hand, the effort to survive has directed increasing interest toward research, a wholesome development in a difficult situation. Wages, limitation of hours of labor, and the NRA have occupied much time and thought. Following a period .of wage cutting paralleling price cutting, the industry found itself rather suddenly faced by the President's Agreement, followed in due course by the Code, and then in many places by the agreement with the United Mine Workers. Although there is still some uncertainty in regard to the detailed working out of the new arrangements, there seems to be an honest endeavor by the signatories to the Code and Agreement to work them out in a straightforward manner.

Jan 1, 1934

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

By R. F. Ashton, D. S. Thompson

In reporting results of precipitation hardening experiments, it is customary to include such conditions as solution heat-treatment temperature, specimen size, and quench medium as well as the aging time and temperature. One portion of thermal history that is often overlooked is the effect of the heating rate employed to achieve the aging temperature. It is the intent of this note to demonstrate the importance of the rate of heating to aging temperatures. This work was carried out on the aluminum alloy 7075 aged at 162oC, a temperature commonly used to obtain stress corrosion resistant tempers. A 2 in. thick plate of 7075 was quenched into 24°C water after solution heat-treatment for 2 hr at 470°C. Approximately 13 in. around the periphery of the plate was discarded to minimize quench rate variations, and the remainder was divided into 0.5 by 1.8 by 2.0 in. blocks which were held at room temperature, 24oC, for 4 days. This aging, or incubation period, at room temperature allowed a copious supply of GP-zones to form. Blocks were then heated at various rates to 162oC using the practices shown in Table I. Both single- and two-step aging practices were employed for each heating rate. The single step consisted of heating directly to temperature at the indicated rate while the two-stage practice included an interruption of heating for 7 hr at 107°C. In the case of the two-stage 100°C per min heating rate experiment, the specimens were returned to room temperature after 7 hr at 107°C where they were held for 16 hr be-fore finally heating at this rate to 162°C. This devia-tion in practice is not considered to be significant. Blocks were removed after various times at 162oC, and aging curves were determined from duplicate R. F. ASHTON and D. S. THOMPSON,Member AIME, are Senior Scientists, Metallurgical Research Division, Reynolds Metals Company, Richmond. Va. Manuscript submitted December 2. 1968. IMD Table I. Aging Practices Two-step Single-Step Heating Rate* Aging Aging Heating Method oC per Min A B Programmed Air Oven 0.23 * 0.01 C D Programmed Air Oven 0.93 ? 0.03 E F Air Oven at Temp -10 G H Oil Bath at Temp ˜100 *Heating rate was measured with a thermocouple at the center of a specimen. An average value between the starting temperature and 3°C below the aging temperature is reported for practices E-H. PRACTICES 70 — A B C E and G 50 - 2 4 6 810 20 40 60 HRS.AT 162°C Fig. 1—The influence of processing variables on 7075 aging curves. Fig. 2—7075 aged according to practice H (single-step aged, fast heating rate) for 3 hr. Magnification 100,000 times.

Jan 1, 1970

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953