Search Documents

By Robert M. Dreyer

Although lateritic ore deposits are relatively flat-lying, surficial ore bodies, the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist. Laterite is a soil formed under tropical conditions resulting in the concentration, within the soil zone, of certain trivalent metals - principally iron and aluminum, but also, locally, nickel and manganese. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of partially altered bed rock or saprolite. Whereas bauxite generally is confined to the lateritic zone, some nickel deposits occur in both the laterite and saprolite zones. The evaluation of bauxite and lateritic nickel deposits thus has both similarities and differences. These ores have been formed by supergene, soil-forming solutions moving downward through zones of widely varying permeability within the weathering rock. Because the permeability varies widely, both vertically and laterally. the extent of weathering may vary greatly within short distances. Because the weathering process varies widely, the degree of metal concentration may also vary widely. It is not at all uncommon for a laterite to change, within a few centimeters, from a virtually valueless rock to a high grade ore. Moreover, the depth of weathering, and hence the depth and form of the ore profile, vary greatly. Obviously, for this type of deposit, a few grab samples or a few drill holes are virtually worthless. The evaluation of such a deposit requires a sophisticated statistical study based on thousands of carefully selected samples. As a rule of thumb, the cost of evaluating a large bauxite or lateritic nickel deposit will be about one cent per ton of ore in the ground. Thus, the cost of evaluating a several hundred million ton deposit may be considerable. The following factors must be considered during the evaluation: Type of Sampling: The best and most reliable samples for the evaluation of lateritic ores are taken along large, vertical channels in hand-dug pits. Where labor costs are high, some form of drilling may be used in place of pitting, but it is always wise to choose a drilling procedure after checking drilling results against a series of pit channel samples. The drilling may not reproduce exactly the results from pit channel samples, but it may be possible to derive a constant correction factor. If the physical character of the laterite varies within the deposit, it may, of course, be necessary to change the type of drilling, the correction factor or both. In some areas, it has been found empirically that augers, chum drills, vacuum drills, rotary drills, or core drills yield satisfactory results. The problem is to find which drilling technique gives results most similar to channel samples through the heterogeneous sequence characterizing the laterite in a given area. In lateritic nickel deposits, the drilling characteristics of the lateritic and saprolitic portions of the deposit are very different. Within the saprolite, the major nickel values are commonly found in weathered zones within less altered boulders - a type of occurrence which makes sampling very difficult.

Jan 1, 1979

By C. E. Armantrout, J. A. Rowland, D. F. Walsh

THE close-packed-hexagonal structure of mag-J- nesium is converted to a ductile and malleable body-centered-cubic lattice by the addition of lithium in excess of 10 pct. Further, the density of magnesium or magnesium-base alloys is decreased by additions of lithium. The practical possibilities of such alloys as a basis for uniquely light, malleable, and ductile structural materials were pointed out by Dean in 1944' and by Hume-Rothery in 1945.2 It was apparent to these investigators, however, that more complex compositions would be required if strengths sufficient for structural applications were to be developed in these alloys. In a search for strengthening additions, various investigators w have examined a number of the ternary and more complex alloys containing magnesium and lithium. An investigation of the fundamental characteristics of these alloys was undertaken by the Bureau of Mines. The investigation was initiated with a study of the magnesium-rich corner of the equilibrium diagram for the ternary system, Mg-Li-Al. The following data from published investigations of Mg-Li-A1 alloys were available: 1—a description of isothermal sections at 20" and 400°C through the Mg-Li-A1 constitution diagram by F. I. Shamrai;' 2—a diagram by P. D. Frost et al." showing approximate phase relationships at 700°F for a number of the Mg-Li-A1 alloys; and 3—diagrams showing the constitution at 500" and 700°F for the Mg-Li-A1 alloy system published by A. Jones et al.' Where compositions and temperatures permit comparison, these diagrams show disagreement. The 700°F isotherms of Frost and Jones differ only in the placement of the phase boundaries. But Sham-rai's 400°C (752°F) isotherm shows a variation in phases as well as in phase boundaries. Although rigid comparison of these different isothermal sections might not be justifiable, it seems impossible to reconcile Shamrai's construction with the isotherms of Frost or Jones. The isothermal sections presented in this paper were prepared to determine compositions which might be suitable for age hardening and to develop the general slope and placement of the various phase boundaries in the magnesium-rich corner of the diagram. Sections at 375", 200°, and 100°C were selected for investigation. In constructing these sections, the solubility of aluminum in magnesium, as reported by W. L. Fink and L. A. Willey Vn 1948, was used at the binary Mg-A1 boundary and the solubility of lithium in magnesium was obtained from the equilibrium diagram for that system as reported by G. F. Sager and B. J. Nelson" in the same year. The solubility of magnesium in lithium was determined experimentally and conforms in general to data reported by P. Saldau and F. Shamrai." Parameters for AlLi and MgI7A1, were taken from American Society for Testing Materials X-ray diffraction data cards. Experimental Procedures Although the isothermal sections presented in this paper are not unusually complex, the experimental techniques involved in their construction are made extremely difficult by the relatively high vapor pressure of lithium and the great chemical activity of both magnesium and lithium. Because of these characteristics, which make precise control of the composition of equilibrium-treated filings practically impossible, the disappearing phase method was used in preference to the parametric method in conjunction with metallographic studies. The alloys used in this investigation were melted and cast in an atmosphere of helium using a tilting-type furnace which enclosed a steel crucible and mold in a single unit. Each portion of the charge (500 to 600 g) was cleaned carefully just before placing it in the crucible; and the charge, crucible, and entire melting apparatus were evacuated and then washed with grade A helium while preheating to approximately 100°C. The alloys were melted and chill cast in an atmosphere of helium. Alloys prepared in this way were relatively free from inclusions and a fluxing treatment was considered unnecessary. The cylindrical ingots obtained were scalped and then reduced 96 pct in area by direct extrusion, yielding % in. diam rod. Sections of the rod, approximately 3 in. long, were given equilibrium heat treatments and then sampled for metallographic examination, X-ray diffraction study, and chemical analysis. The surface of each equilibrium-treated rod was machined to a depth sufficient to insure removal of contaminated material before samples for chemical analysis or X-ray diffraction study were obtained, and all decisions on microstructure were based on the examination of the central portion of the metallographic specimen. All specimens homogenized at 375°C were analyzed after this equilibrium heat treatment. When the composition of an alloy placed it in a critical area of the 200" or 100°C isothermal section, a check chemical analysis was made on a sample taken from the alloy specimen as-heat-treated at the particular temperature. Standard chemical procedures of gravimetric analysis were used in the determination of magnesium and aluminum; lithium, potassium, and sodium were determined by flame photometer methods

Jan 1, 1956

By V. H. Wilhelm

Developments in California during 1942 were marked by many difficulties in operation, of which the lack of labor and material were the main factors in slowing down work. During the many years of curtailment, which has been effective since 1928, a number of estimates of the state's capacity to produce have been built up, but during the year 44 fields were 'eliminated from curtailment and valuable data were obtained as to the normal capacity of these fields to produce. Because of new discoveries and the normal decline of old fields, which is more than 15 per cent per year, it is estimated that the sustained capacity of the state for a 5-year period is not more than 500,000 bbl. per day. Decline in the rate of production was greatest in the fields in the Los Angeles Basin district. These fields have been produced nearly at capacity for many years and had no reserve of shut-in production. The San Joaquin Valley and Coastal districts have responded well to the increased allotments assigned to them by the Petroleum Administrator for War. All heavy oil fields in the state are on full production, except in the Coastal district, where transportation is the limiting factor. Although approximately 2500 more wells are on production in the state than there were in 1941, the supply of heavy crude has not yet reached the demand. A summary of statistics for 1941 and 1942 is given in the following table. Production in California for 1942 was 680,000 bbl. a day as against 631,000 bbl. a day for 1941, an increase of 7.8 per cent. The present maximum efficient rate has been estimated at 808,000 bbl. per day. This indicates that in the 15 restricted fields of the state there is only an additional 83,000 bbl. per day of light oil available. Drilling Activity Drilling activity during the year was equivalent to but 70 per cent of normal. Although shortages of equipment and labor were in part responsible for the reduced drilling activity, the main reasons were the lack of proved locations due to a cycle of very few new discoveries and the restrictions of Conservation Order M-68. For the first six months of the year, 300 new oil wells were completed, which were equally divided as to the number of light and heavy oil producers. But, for the last six months of the year, it is

Jan 1, 1943

By V. H. Wilhelm

Developments in California during 1942 were marked by many difficulties in operation, of which the lack of labor and material were the main factors in slowing down work. During the many years of curtailment, which has been effective since 1928, a number of estimates of the state's capacity to produce have been built up, but during the year 44 fields were 'eliminated from curtailment and valuable data were obtained as to the normal capacity of these fields to produce. Because of new discoveries and the normal decline of old fields, which is more than 15 per cent per year, it is estimated that the sustained capacity of the state for a 5-year period is not more than 500,000 bbl. per day. Decline in the rate of production was greatest in the fields in the Los Angeles Basin district. These fields have been produced nearly at capacity for many years and had no reserve of shut-in production. The San Joaquin Valley and Coastal districts have responded well to the increased allotments assigned to them by the Petroleum Administrator for War. All heavy oil fields in the state are on full production, except in the Coastal district, where transportation is the limiting factor. Although approximately 2500 more wells are on production in the state than there were in 1941, the supply of heavy crude has not yet reached the demand. A summary of statistics for 1941 and 1942 is given in the following table. Production in California for 1942 was 680,000 bbl. a day as against 631,000 bbl. a day for 1941, an increase of 7.8 per cent. The present maximum efficient rate has been estimated at 808,000 bbl. per day. This indicates that in the 15 restricted fields of the state there is only an additional 83,000 bbl. per day of light oil available. Drilling Activity Drilling activity during the year was equivalent to but 70 per cent of normal. Although shortages of equipment and labor were in part responsible for the reduced drilling activity, the main reasons were the lack of proved locations due to a cycle of very few new discoveries and the restrictions of Conservation Order M-68. For the first six months of the year, 300 new oil wells were completed, which were equally divided as to the number of light and heavy oil producers. But, for the last six months of the year, it is

Jan 1, 1943

By Henry M. Howe, Joseph Winlock, Francis B. Foley

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923

By Joseph Winlock, Francis B. Foley, Henry M. Howe

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923

Frank 11. Probert, Neudorf, Anhalt, Germany (communication to the Secretary): I have read with much pleasure Mr. Collier's valuable paper. But the system of timbering which he describes as used in the levels, stopes, etc., though it must be admitted to be very strong and safe, seems to me somewhat extravagant. The amount of timber required every month for such a system must be enormous; and only where suitable material could be cheaply obtained would such a plan be economically practicable. The first point which strikes me is the unusually great diameter of the timber employed. In the mines of Pfaffenberg and Meiseberg, which are under my supervision, the country-rock consists of argillaceous slates, traversed by innumerable small fissures or joints, dipping at all angles and striking to all points of the compass. Undoubtedly, this net-work has been caused by the upheaval of granite masses in the vicinity. Each fissure is accompanied by a more or less well-c1efinc.d gouge or fluccan, caused by the rubbing together of the slates at or after the original disturbance. In such

Jan 1, 1900

By E. E. Schumacher, G. S. Phipps, H. M. Bouton

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By H. M. Bouton, G. S. Phipps, E. E. Schumacher

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By H. W. Rogers

The first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 1, 1915

By Benjamin Talbot

The problem of segregation and cavities in steel ingots is a subject which has given and is still giving metallurgists, engineers, and operators matter for serious consideration. This question has come more into prominence lately in the United States, due largely to the desire of railroad engineers to secure a better rail than they have obtained ill the past, as the service they demand is increasing in severity; and no doubt manufacturers will be able to meet what is required of them. The rails here are as good as those made in other countries, but the conditions of service and the extremes of climate are more Revere and consequently more breakages occur. Various reasons have been advanced to explain why rails may not be as good in quality to-day as in the past. Some engineers consider that modern methods of manufacturing, designed chiefly to obtain large output, tend to reduce the standard of excellence of more deliberate methods. Others think that 4-ton ingots are worse than those of 2 tons. Again, it is stated that the 100-ton heat in one ladle is too large, and is a step in the wrong direction in casting. My experience upon the question of the size of the ingot is that in rolling rails of from 85-to 100-lb. sections, the range of ingot is only practically such that the difference in the size does not help in the question of segregation, cavities, or blow-holes. I call attention to two ingots from work done at Pencoyd, Pa., 16 years ago. These ingots were bottom-poured, cast at the same time from the same center-runner, the one being 20 by 24 in. and the other 13 by 16 in. in size. The steel was acid open-hearth, and contained C, 0.43; P, 0.062; S, 0.069 per cent. At the same place in each ingot where seg-

Jan 1, 1914

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By James Hyslop

MECHANIZATION of American coal mining continues to make rapid progress. Economic pressure will compel abandonment of manual methods wherever possible and will also provide the incentive needed for the improvement of machines and mining systems. However, rapid progress may be made along strictly technological lines and at the same time much slower progress in approaching maximum productivly and efficiency. One can well ask, just how efficient are mechanized mines, and to what extent is productivity affected by the mental attitude of management and workers?

Jan 1, 1946

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By Francis S. Kendorski

Caving offers the lowest cost per ton of ally large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently-taken on new importance as deeper, lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface mining methods, and too low grade to support any type of underground mining except a bulk method such as caving.

Jan 6, 1978

By Ingersoll Olmsted

Mr. D. H. BRowne's paper upon " The Distribution of Phosphorus in the Ludington Mine" (Trans., xvii., 616) has interested me very much, and perhaps I cannot give a better proof of that, interest than an account of my work and observations in the same direction while chemist of the Hudson River Ore and Iron Company. The ores of this company lie in a chain of low hills running northwest and southeast, about three miles back from the eastern bank of the Hudson river, below Hudson, N. Y. They occur in thick veins, with the characteristic Hudson river slate formation as hangingrock and foot-wall, and dip about 45' east, outcropping in many places near the top of the western slopes.

Jan 1, 1890

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By New kensington P. A, W. L. Fink, H. R. Freche

The investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)† and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (3) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigatcd up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations. No attempt will be made here to present the history of the development of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the subject. Two thermodynamic equations, which will be employed extensively in this paper, are: loge x1 = - L/RT + C

Jan 1, 1934

By Paul Billingsley

CERTAIN adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rooks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado dis-tricts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on final Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make cross-roads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coast and Canadian Coast Ranges. Essential function of repeated deforma-tion is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci.

Jan 1, 1939