Search Documents

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry's law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969

By R. W. Smashey, B. J. Piearcey

The structure, composition, and morphology of the carbide phases present in the nickel-base superalloy, Mar-M200, hare been determined and three carbide phases observed. The MC carbide is a solidification product, and the M23 Co and M6C carbides are both prod~icts of solid-state precipitation. The identity of each phase usas determined by both X-ray and electron-diffraction techn~ques. Compositions of all three carbides were studied using the electron beam micro-probe analyzer and by unalyszs of electrolytically extracted residues. Optical and electron microscopy were employed in order that the time/temperature -dependent behavior of the carbides might be observed. Supplementary studies were completed on thin foils and oriented single crystals to determine the mor-phology and orientation relationship of each phase with that of the matrix. MAR-M~OO* is a high-temperature, creep-resistant superalloy designed for use in the as-cast condition. The "as-cast" microstructure consists of a solid-solution matrix, referred to as gamma (y), which contains a general, coherent precipitate of the inter-metallic Ni3(A1,Ti) referred to as gamma prime (?). As a result of dendritic segregation during solidification, a degenerate, spherulitic ? -?' eutectic constituent is present at the grain boundaries and the in-terdendritic regions, which is nucleated by the y on the dendrite tips. A primary carbide phase, a solidification product, is also present at the grain boundaries and in the interdendritic areas, and an additional carbide appears at the grain boundaries as a fine discontinuous precipitate. The alloy is particularly susceptible to heat treatment. For example, the mechanical properties of the columnar grained mater- ial are substantially improved by solution heat treatment, followed by an intermediate temperature age. Metallographic examination of heat-treated material reveals, however, that exposure to elevated temperatures has a marked effect on the microstructure of the alloy; in particular, it is observed that precipitation of considerable amounts of various carbide phases occur. The following investigation was carried out to determine the morphology, composition, and behavior of the carbides in Mar-Ma00 as an aid to the determination of their effect on the mechanical properties and stability of the alloy. THE PRIMARY MC CARBIDE The MC carbide phase appears in the interdendritic interstices and the grain boundaries. In directionally solidified Mar-M200 the carbide appears as very small particles in the chilled region, Fig. l(a), whereas in material less affected by the chill, it becomes larger and develops a dendritic morphology, Fig. 1(b). Step polishing of metallographic specimens from this region shows that in directionally solidified material the individual carbide dendrites are connected in a dendritic network within the metallic interdendritic interstices, whereas in material from the chilled region and in conventional Mar-M200 they are discontinuous, isolated dendrites. No orientation relationship exists between the primary carbide and the matrix.

Jan 1, 1968

WILLIAM H. KOBBÉ (communication to the Secretary*).-I have read with much interest the discussion of my paper by Arthur Knapp and I. N. Knapp published in the March Bulletin. These discussions apparently assume that my paper advances a. number of ideas that are not intended: 1. That the total sandbody or pay is to be removed. 2. That upon bringing this sand and oil to the surface 100 per cent., or perfect separation, can take place. 3. That this tremendous quantity of sand is then hauled away in wagons and distributed as road material. The paper raider discussion is not a theoretical treatment of the subject but is the result of actual experience in oil production under the conditions mentioned.. That wells that produce sand produce in ore oil, and the best operating methods to bring this about are fully treated. It is, of course, impossible to remove all the oil sand underlying a property, but the greater the amount removed the greater becomes the production of oil. As stated in my paper, the surface disposal of this large volume of sand is a problem and the only use to which it can be put is road surfacing; but I did not intend to convey the idea that all this sand was thus used. Only a very small quantity was required on the company's roads, and two wagons only were employed for this purpose. The remaining sand accumulated in the numerous "washes" and sumps. Although this sand contained sufficient oil to stain the hands, it was, surprisingly dry and could be easily shoveled. As stated in the paper, "the piles of sand are gradually freed of their oil content and a crust forms on their surface which will bear the weight of a man." I consider this a high degree of separation. A small amount of oil necessarily remains in the sand and is held there by capillarity. Otherwise it would be useless as a road binder, and, furthermore, to recover such oil special processes of treating are required. Arthur Knapp says, "of the total volume produced by pumping, not more than 4 or 5 per cent. can possibly be sand." I cannot agree with this statement as I have managed many properties where the wells were so operated that the amount of sand produced was five times this figure.

Jan 6, 1917

[ ]

Jan 1, 1938

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By J. K. Stanley

IT has been known for many years that the magnetic properties of a ferromagnetic material are very sensitive to internal strain. Any structure-sensitive property such as ferromagnetism, which is a-function of the regularity of the atomic arrangement, and discontinuities such as grain boundaries must show deviations from an equilibrium state when the regularity of the lattice is disturbed. Experience has shown that such distortions have a marked effect on the magnetic properties of a ferromagnetic material. The purpose of this paper is to show the feasibility of using magnetic methods in detecting internal strains. More specifically, it will be shown how such properties as permeability, remanence, and coercive force change on cold- working of aluminum iron and how these magnetic properties change during the annealing below the recrystallization temperatures. This work was conducted for two reasons. One was the desire to see in what manner strains are relieved in aluminum iron at low temperatures-a subject of practical importance in soft magnetic materials-and the other was the feeling that a study of cold-working and strain relief might shed some light honour understanding of what takes place in the deformation of metals DEFINITION IN TERMS It is necessary to define the terminology used in this paper because magnetic nomenclature is usually unfamiliar to the metallurgist, and certain other terms, such as recovery, have been used ambiguously by metallurgists and others. Magnetic terms are best explained by reference to the common hysteresis loop of ferromagnetic materials (Fig. I). In Fig. I the coordinates are magnetic induction, B, (ordinate) and magnetizing force, H, (abscissa). The c.g.s. unit for the magnetic induction is the gauss, the number of flux lines per square centimeter, and the unit for the magnetizing force is the oersted, the number of lines of force per centimeter in air or vacuum. If one starts with a completely de- magnetized specimen and magnetizes it, a typical virgin magnetization curve beginning at the origin is obtained. This curve is also the locus of tips of a family of smaller hysteresis loops. From this curve it is to be noted that the induction is not proportional to the magnetizing force, and that it appears to approach a limiting induction called the saturation value, and does so for values of H of 1000 oersteds. The ratio of the magnetic induction (gauss) to the magnetizing force (oersteds) is called permeability, p. Thus µ = B/H and if the magnetizing force H (oersteds) is specified as 10 or IOO oersteds, the permeability is written as µ10 or µ100. This is the accepted notation, and will be used in this paper. The values of permeability for H = 10 or 100 are chosen as indices for

Jan 1, 1945

IN THE early evening of October 15, 1954, a large specially designed truck, convoyed by a second smaller one, arrived at Silver Bell, Arizona, completing a ten-hour 110-mile journey from Phoenix. The big truck was driven through gaps left in a previously prepared concrete foundation, the load was jacked up, the large girders that constituted the bed of the truck were pulled away, and the load was then lowered into place on the foundation. A crew of two men, the two truck drivers, finished the job in a little more than an hour. When they were through, a complete and attractive three-bedroom house, prefabricated in Phoenix, was almost ready for occupancy. About all that remained to do was to connect the utilities-water, electricity, plumbing, and gas. The kitchen and bathroom equipment and appointments were superior in every respect, and there was a built-in car port for the automobile of the prospective residents. This family domicile was one of more than one hundred, each averaging about $8,000 in cost, that the American Smelting and Refining Company has provided for its employees engaged in mining and milling 7,500 tons per day of low-grade Porphyry copper ore. Aside from the fact that it is more economical-partly because of the variety of union craftsmen needed to build and equip a house-to do the work in a city 110 miles away, the significant point is the high quality of housing that is provided for what may be called in nostalgic vein the "mining camp" of 1955. Silver Bell is typical of all the Porphyries in this respect though the community is relatively small. At San Manuel

Jan 1, 1957

By EDWARD B. DURHAH

The illustration Fig. 12, of the paper of Edward B. Durham, "Electrolytic Refining at the U. S. Mint, San Francisco, Cal.," printed in Bulletin No. 58, October, 1911, p. 830, contained an error. The corrected diagram is printed below.

Nov 1, 1911

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952

By Tell Ertl

TODAY'S mining industry is witnessing a transition in labor utilization. The drill-jumbo operator, the mucking-machine operator, the blasting crew, the scaling and timbering crew are all specialists. The all-around miner is rapidly disappearing. As mechanization has resulted in a higher order of underground skills; specialization of labor has been a natural consequence, as has the need for more supervision and engineering. Mines now are cleaner, neater, safer, and have a greater productivity per man-shift than ever before. Nothing spectacular like the continuous miner has yet come to the underground metal mines, but t a gradual improvement in methods, equipment, and technical knowledge is achieving the increased efficiency. With the exhaustion of the rich ores and large profits and who-cares-about-the-costs, mining has become a business; that of producing low value ores at costs below selling price. Charles A. Chase, patriarch of Colorado mountain mining men, manager of the Shenandoah-Dives, was one of the first to preach and prove his preachings that mining is a business. He has been mining a lead-copper-zinc-gold-silver ore, much from elevations above 1.3,000 ft, for a quarter century without a shutdown.-The ore is of such low value that most engineers and investors still would consider it foolhardy. Yet he has kept Silverton, Colo., alive, has paid wages without a lapse, has produced $25 million of new wealth and maintained a steady return to the investors. This type of responsibility is increasingly apparent in the mining business and is one feather that can be worn proudly. .Much emphasis is being placed on improving, the productive mining operations-breaking, loading and transportation. Breaking in underground metal mining is done by drilling and blasting. To the writer's knowledge, no chain or rotary-type machine has been developed for mining strong, abrasive rock. Drilling Percussion drills are still the standard drilling machines underground. Diamond drills, that: were the rage a decade ago for drilling long holes, are being superseded by the rock drill. The development of the hard abrasion-resistant carbide bit permits full-gage long holes to be drilled by percussion drills at a lower cost than diamonds. The change in the use of percussion drills is chiefly in the method of mounting. The column and arm are disappearing and the jackleg and rubber-tired or track-layer jumbo mountings are taking its place. At the Homestake mine .lightweight jackhammers mounted• on pneumatic legs using 7/8-in. hexagonal drill. rods and 1 1/2-in, tungsten-carbide detachable bits have been found more portable and maneuverable. They have less air consumption, lowered, dynamite consumption, and more footage and tonnage per man-shift than with 3 1/2-in. drifters on a column mounting. Drills now are mounted on longer feed carriages, drilling up to 20 ft without changing steel. These mountings result in great savings because the driller can set up quickly, drill the entire depth of the hole without changing the drill rod or bit using carbide and one-use bits, and can move his machine quickly to the next hole. One man to the machine is becoming general practice. The result is longer rounds rounds drilled at a lower cost than the previously used short rounds. A jumbo developed in the Tri-State can be extended to mine ore left in the roof up to 65 ft above the floor. Drill-rod life was formerly considered to be about 250 min of actual use. The increase in the drilling time per rod per day has gone up considerably with the development of the jumbo and the long-feed carriage, resulting in which is apparently more rod breakage., Consequently, a great deal of research is being done in the attempt to develop an alloy-steel rod with longer service life to offset the greater cost. Some reports indicate that alloy steel or Swedish steel results in cheaper drilling than conventional drill rod. However, several tests have shown only slightly increased life for alloy drill rod. Undoubtedly, the blow of the rock drill, the length of the drill rod, and the resiliency of the rock being drilled are important factors in the life of drill rod, so it follows that alloy steel might work well in some mines and result in no savings in others. The bit forged on the drill rod is seldom encountered and steel detachable bits are not as common as in the recent past. The one-use bit is gaining popularity because of. the difficulty in rehardening reconditioned steel bits satisfactorily. It is thought that the, carbie-insert bit is most applicable to drilling hard 'rock' where the steel bit is unable to drill out a full change, for instance, in extremely abrasive

Jan 1, 1952

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By S. M. Marshall

FOR a number of years European investigators have used laboratory methods of predicting the probable strength of coke made from coal, and recently several investigators in the United States have reported the use of various tests for this purpose. There is at present no method accepted as standard, however, nor is there even agreement as to the general type of test that should be used. Furthermore, because the details of most of the tests have not been worked out carefully, one investigator can not hope to duplicate the work of another. The extension of coke manufacture to new localities in the United States, and the increasing need for cokes of exceptional qualities made from the most economical mixtures, made it desirable to have some simple laboratory test which will determine whether given coals, alone or blended with other coals, are more satisfactory from the standpoint of coke strength than others of different cost. The work described herein has resulted in the development of a simple laboratory test which, it is believed, can be generally adopted in coal laboratories, and which will give concordant results even though performed by different investigators in different laboratories. The general method of predicting whether a coal or a mixture of coals will produce a strong coke, resistant to crushing and shattering, has been to correlate the known strengths of the cokes produced in commercial ovens with some measurable constituent or with some property of the coals, and then to use the relationship so found for forming an estimate of the coking strengths of coals unknown. Several such correlations have utilized the percentages of the various ultimate constituents of coal, such as the oxygen content and the hydrogen-oxygen ratio;(39)§ other correlations have involved the proportion of a, (3 and y compounds, (17'21,30 or of "oil and solid bitumens."(16,30) Also a relationship has been traced between the coking properties of coal and the rate of change of the resistance offered to the flow of an inert gas by fine particles of the coal while being slowly heated. (11,17b) But the most general corre-

Jan 1, 1929

By F. M. Lewis, J.F. Myers

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By J. F. Myers, F. M. Lewis

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By Henry Kreisinger

IN evaluating coals as steaming fuel on the basis of chemical and physical properties of the coals, the only properties that can be used are those for which the methods of determination are well established and standardized, and those that affect all methods of burning the coals in the same way. The discussion is written from the standpoint of the coal consumer. The production of steam is the largest field for the use of coal. It includes stations for generating electric power, central heating plants, industrial power plants where steam is used for power generation, factory processes and heating. The field also includes steam locomotives. Small house-heating boilers are not included in this field because such small boilers generally burn specially prepared domestic fuel. The plants using the steam coal are equipped to burn the coal when fired by one of the three general methods: namely, hand, stoker, and pulverized coal. The hand firing is now restricted to small plants and to locomotives. Central stations and larger industrial plants use either stoker or pulverized-coal firing. Some locomotives also use stokers. Pulverized-coal firing has been tried in locomotives but so far its adapta-tion to this use has been handicapped by practical difficulties. The coals used for steaming purposes are generally of the bituminous and semibituminous classes, with volatile matter ranging from 15 to 35 per cent. Coals belonging to these classes are produced in many parts of the United States and form by far the largest part of the total coal production of the country. The value of any coal as fuel for steaming purposes depends on the following factors

Jan 1, 1935

By T. P. Clendenin

THE northerly two thirds of Mexico falls into five main physiographic divisions, illustrated on the accompanying map. In form, these divisions are a series of strips, paralleling the northwest-southeast axis of the country.

Jan 10, 1951