Search Documents

By H. S. Bell

It seems unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remark-able operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to analyze theoretically the partisl-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9° Be. North Texas crude. The chart is illustrative of batch distillation. Theoretically, if the oil were heated by a single flash in a pipe still, the partial-pressure effect of the light products would result in the removal of the same amount of vapors at a lower temperature. Practically, we find that because of the necessarily extensive fractionating equipment required when separating many products all in vapor phase, the oil has to enter the separator at temperatures corresponding to or even above those required in the batch still. Furthermore, in single-flash distillation the vapors evolved in the heater must be superheated to the outlet temperature. Very little is

Jan 1, 1928

By Nicasio del Castillo

INTRODUCTION The tax structure of foreign mining investment into the United States has a significant impact on the financing and the profitability of the operation. For these reasons, it is critical for the foreign investor to develop and implement a well planned tax strategy that will enable its venture to: (1) reduce its U.S. income tax liability (2) lower U.S. withholding taxes when funds are transferred from the United States, and (3) decrease or defer home country taxation on its U.S. earnings ALTERNATIVE FORMS OF INVESTMENT A threshold business and tax consideration is the form in which the investment is to be made. The most common alternatives include: forming or acquiring a U.S. mining corporation, directly establishing a branch mining operation, or entering into a joint venture or partnership with a U.S. mining company. U.S. Corporations The most common structure through which foreign mining companies engage in business in the United States is to form a U.S. mining corporation. Forming a U.S. Corporation. If the investor decides to establish a new U.S. corporation the organization is relatively simple. No distinctions are made in the United States between "public" and "private" forms of incorporation. Minimum share capital is not usually required and share capital may consist of shares with no par value. Since corporate law is the responsibility of the individual states, the foreign investor must choose a state in which to incorporate. If appreciated mining property is transferred to a corporation solely in exchange for stock or securities in that corporation, and the transferors have control of the corporation (defined as at least 80 percent of all voting shares and at least 80 percent of all other shares) immediately after the exchange, no gain or loss will be recognized. However, if the transferors receive cash or other mining properties in addition to stock, any resulting gain may, in certain situations, be taxed to the extent of the cash and the fair market value of other property received. Acquiring an Existing U.S. Corporation. Acquiring an existing U.S. mining corporation is not as straight-forward as forming a corporation. This alternative may be accomplished through either a stock or an asset acquisition. Generally, with a stock acquisition the purchaser inherits all of the business and tax attributes of the former mining corporation. If the investor is able to acquire mining assets, however, the purchaser will usually be able to avoid any unknown or hidden liabilities that could be attached to an existing corporation. Another principal advantage in acquiring assets is that the purchase price may be directly allocated to the acquired mines or other mineral-related assets with the result that the assets' depreciable base may be increased. Assuming the domestic seller and the foreign purchaser can agree, it is generally advisable to allocate the purchase price in the sales agreement to specific individual assets. From the foreign investor's standpoint, it is preferable to allocate the purchase price to depreciable assets such as buildings and equipment versus an allocation to mineral land holdings or intangibles such as goodwill, which are generally not depreciable. It is not uncommon, however, for a seller mining company being acquired to insist for tax reasons that the investor purchase shares rather than assets. If the foreign

Jan 1, 1985

By R. V. Norris

The removal of mine-water by hoisting in tanks instead of pumping, while somewhat a reversion to the methods of the ancients, has come very rapidly into favor in the anthracite region of Pennsylvania during the past few years. In fact, so much so, that at the present time there are at least eight large collieries at which all the water is hoisted, and six more plants are in preparation. The particulars of the plants in operation and under construction, as far as decided on, are given in the tables on pages 107 and 108. Besides these, the Delaware, Lackawanna and Western R.R. Co. is constructing a hoist of large capacity for a depth approximating 500 feet, to be located in the Keyser Valley, near Scranton. The hoists will be driven by electric motors, geared directly to the sheaves. The Lehigh Valley Coal Company is planning a large hoist for the Packer collieries in the Shenandoah district, but no work has been done on this as yet. The earliest regular hoisting, I believe, mas done by means of semi-cylindrical tanks (Fig. 1) at the Nanticoke collieries of the Susquehanna Coal Company. These tanks were attached under the regular shaft-carriages, taking in water through six large clack-valves in the bottom, and discharging through an endgate opened by a lever which was operated by a guide-piece on the shaft head-frame. These tanks were designed July, 1880, by the late J. H. Bowden, one of the very early members of the Institute. Similar tanks are still used in emergencies at the Nos. 1, 2, 3 and 6 shafts of the company. The objections to. their use were: that water could only be hoisted during the night-shift, or when the shafts were not in use for hoisting coal, thus requiring a very large sump, and greatly limiting the water capacity of the plants; that the alternate wetting and drying

Jan 1, 1904

By Charles Baskerville

SHALES containing,"kerogen,," or bituminous matter, which on destructive distillation yield oily and tarry matters resembling petroleum are here designated as oil-shales. They differ from oil-bearing shales from which petroleum may be obtained by so-called mechanical means. The educts obtained by the destructive distillation resemble some or all the varieties of petroleum, depending on the character of the shale and the mode of treatment. Some shale oils have e a paraffin base, some an asphaltic base, or a combination; some run high in sulfur compounds, The methods of refining and cracking, therefore, are essentially the Sam as are used in refining petroleums. In 1860, in this country, over fifty companies were successfully distilling various bituminous natural materials for the production of "coal oil," used for illuminating purposes. The discovery of petroleum and the failure of these companies to save and utilize the valuable byproduct, ammonia, brought about their inevitable doom. Prior to that time, more or less successful efforts were made to produce from the shales of Scotland oils for illuminating and heating purposes. Competition of native petroleum from the United States early eliminated some of these companies and with the entrance of oil from the Russian and other fields into the world's markets, the Scottish oil-shale industry underwent serious and trying experiences until, in 1916, only four (Scottish) were paying concerns.. These survived only through energy and the application of skill in saving valuable byproducts. A few companies have successfully operated in France and New Zealand. The Canadian Government showed active interest in the New Brunswick shales, which exist in quantity and are more valuable than the Scottish shales. The retarded development of that very valuable asset of the Province of New Brunswick involves a pathetic history, which is lamentable. This was especially true when the product was so much needed in the prosecution of the war. The economic success of a shale-oil industry depends on the following factors:

Jan 6, 1919

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep under-ground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county pro-vides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest com petitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By Charles W. Goodale

In the course of the preparation of my paper on " The Occurrence and Treatment of the Argentiferous Manganese Ores of Tombstone District, Arizona" (Dam., xvii., 767), my attention was called to two patents which have been issued for the use of a diaphragm at the upper end of a Howell furnace, whose importance merits more than a passing reference. Mr. J. K. Pardee invented and first put into use in the Algon quin mill, at Philipsburg, Mon., in 1880, a ('new' and useful im provement in rotary ore-roasting furnaces," which was intended "to increase the capacity, effectiveness and working economies of such furnaces." The following description and accompanying figures are taken from the patent papers, dated December 21st, 1880: Fig. 1 is a side elevation of the feed-end of the Howell rotary furnace, with parts broken away, the better to exhibit my invention. Fig. 2 is an end elevation of the same. Fig. 3 is an end elevation of the same, showing a modification of my invention. In operating a furnace of this kind, of the capacity of one ton of ore an hour, it was found that for the best work the two fire-places (one at each end of the revolv ing cylinder) consumed about ten cords of wood every twenty-four hours, and that about twenty-fonr tons of silver-ore were introduced through the feed-pipe. It was also found that of the amount of ore, fully one-third did not go through the revolv ing cylinder, but went into the dust-chanibers about the feed-end of the furnace or cylinder, and this ore going into the dust-chambers was found not to be sufficiently chloridized for amalgamation, but had to be re-roasted. I then caused to be made, out of boiler-plate iron, a segment of a circle, the height of which was about one third of the diameter of. the cylinder or furnace, the circumference of the circle being smaller than the circumference of the furnace, so that about a half-inch space would be left between the plate and the furnace, when said plate or segment was in position. This segment or plate of iron was then fastened to the bottom of the feed pipe, as shown in the drawings, wherein A represents the revolving cylinder or furnace; B, the fire-place and dust-chambers at the feed-end of said furnace; C, the inclined feed-pipe, and D, the diaphragm, partition, or plate fixed within said furnace, A. With the diaphragm or plate, D, in the position shown, the furnace was run for about a month, and it was found that with the furnace in best working condition only four cords of wood every twenty-four hours were consumed, that no fire was required at the feed-end of the furnace, that not one-twelfth of the ore

Jan 1, 1890

By W. C. Hagel, H. J. Beattie

Phases present at 2200° and 1500°F (1204° and 816°C) were identified in sixty wrought developmental austenitic alloys possessing wide compositional variations. The bases were iron-, cobalt-, and nickel-rich as well as a base with equal parts of each. There are only two structure types previously not found in similar alloys, viz .-the Co3 W and the Fe3Al types. A molybdenum-rich monocarbide decorates dislocations with unusual clarity. Other results provide correlations between alloy composition and phas e precipitation. Grouping intermetal -lic phases into three general classes : I) geometrically close-packed, 2) topologically close-packed, and 3) bcc derivatives, the nickel base prefers the first, the iron base the second, and the cobalt base the third—each base tending to shun the other two classes. Thus, a crystal-chemistry effect previously noted by Laves and Wallbaum can he expanded for these Group VIII elemental bases. There appear to he no quaternary or higher -order structure types requiring more than three atomic species. AFTER studying aging reactions in many diverse commercial austenitic alloys1-4 as a function of detailed time-temperature variations in heat treatment, it became apparent that matrix composition influenced structure types and morphologies to a large extent. These tendencies were related4 to a crystal-chemistry effect uncovered by Laves and Wallbaum.5,6 We have now directed our efforts to exploration of the whole ternary field, covering the standard base elements—iron, cobalt. and nickel— with 10 to 20 pct Cr and moderate amounts, up to 10 pct, of the usual alloy additions. Solutioning and aging treatments were held constant with major emphasis on X-ray identification of microconstituents. The possible existence of exceptions to the Laves-Wallbaum effect, or any new phases, was sought. Phases appearing in austenitic alloys can be classified as geometrically close-packed (gcp), octahedral or nonoctahedral interstitial compounds, topologically close-packed (tcp), semicarbides, and bcc derivatives. Crystal structures of the first four classifications can be visualized as a dense packing of semirigid spheres of different sizes, while the bcc derivatives represent a less efficient packing of spheres. The Laves-Wallbaum effect involves the gcp and tcp phases. Gcp phases possess both tetrahedral and large octahedral interstices; examples are Ni3Ti(n), NiSAl(y'), Co3W(E), and other ordered AB3 compounds where B atoms are smaller than A. Their precipitation is primarily intragranular, presumably coherent with an austenitic matrix, and a chief source of strengthening. Most octahedral interstitial compounds (e.g., CbC, Tic, TiN, Mo2C) have a gcp lattice of large metal atoms which accommodate small carbon or nitrogen atoms in the octahedral interstices. The compound Ti2SC, previously designated Y phase or T phase, can, with some reservation due to its partial co-valency, be placed in this category.7 The nonoctahedral interstitials (e.g., M7C3, Fe3C) represent close-packings of spheres in structures that provide larger triangular-prism interstices for carbon, since the octahedral interstices formed by chromium and iron atoms are too small. Tcp phases possess only tetrahedral interstices; examples are Laves (Fe2Ti, Fe2Cb, Fe2W...AB2), p(Fe7MO6, Co7W8.... A8B7), and (FeCr, Co2Cr3)

Jan 1, 1965

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By D. H. NETLAND

DURING the year 1907 an investigation of the Clinton formation in New York has been carried out under the direction of the State Geologist, and a full account of the results has been prepared for publication.1 The more important economic features of the report are summarized in the present paper. Previous knowledge of this, the type, section of the Clinton has been contributed mostly by Hall and Vanuxem in their reports for the Natural History Survey of New York, which were issued in their final form in 1842-43. Brief accounts of the ore-occurrences have been given by B. T. Putnam,2 J. C. Smock,3 A. H. Chester,4 and E. C. Eckel.5 Prof. C. H. Smyth, Jr.,6has discussed the origin of the Clinton ores in two papers, which, so far as the local occurrences are concerned, have removed all doubt that may have existed on that subject. Distribution of the Clinton Formation. The Clinton strata in New York State are restricted to a single belt, Which extends from the eastern central part to the Niagara river, which it crosses, and thence continues for some distance into the province of Ontario. The New York

Mar 1, 1909

I BELIEVE that my work would surely be host a seed without fit and that I would fail in that cause which disposed me to satisfy your request to write and form this work [75] if while laboring on it I did not tell you of the art of casting, since it is a necessary means to very many ends. I realize even more that I must tell as much as seems necessary since I have already demonstrated the methods of recognizing the natures and locations of the metals, of smelting and reducing them to their ultimate perfection, and finally have taught you to make their associations and alloys. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed. In order to describe the whole art in every part, I say that the greatest labors of both mind and body are required for its operations in the beginning, middle, and end. It is indeed true that these labors are endured with pleasure because they are associated with a certain expectation of novelty, produced by the greatness of art and awaited with desire, particularly since the artificer sees that it is an art pleasing and delightful even to ignorant men. As a result, as if ensnared, he is often unable to leave the place of work. To conclude: The outcome of this art is dependent upon and subject to many operations which, if they are not all carried out with great care and diligence and well observed throughout, convert the whole into nothing, and the result becomes like its name [cast away]. Therefore, having considered this work many times, with its extraordinary obstacles and the bodily labors heavy as a stevedore's, instead of exalting it with praise, I wish to say that it is such that a man of noble birth, even though he be gifted or be drawn to it by pleasure, should not practice it and could not unless he is accustomed to the sweat and many discomforts which it brings. He must suffer the great natural heats of summer as well as those excessive and continuous ones from the enormous

Jan 1, 1942

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

[Appalachian Petroleum Section: Walter H. Chapman, chairman; Jean Freeland, first vice-chairman; John Galpin, second vice-chairman; Jack L. Trittipo, secretary-treasurer. Meets 4th Tues., Humphreys Restaurant, Charleston. Balcones Section: William E. Richards, chairman; William C. Miller, Jr., first vice-chairman; Brantley G. Myers, second vice-chairman; Harold Vagtborg, Jr., secretary-treasurer. Meets 4th Wed., Petroleum Center Club, San Antonio. Big Horn Basin Subsection: Donald G. Davis, chairman; B. E. Yester, vice-chairman; J. F. Keleher, vice-chairman; Samuel N. Conley, third vice-chairman; William O. Snyder, secretary; M. J. England, treasurer. Billings Petroleum Section: N. J. Matthews, chairman; Guy J. Lookabaugh, first vice-chairman; George O. Ellis, second vice-chairman; Robert L. Spottswood, secretary-treasurer. Meets 3rd Tues., Turf Penthouse.]

Jan 1, 1961

By John A. Hosking

The recent activity of numerous foreign mining companies in the once flourishing tin fields in Cornwall, England has resulted in renewed interest in the evaluation of hypothermal tin deposits. These deposits are mainly narrow tabular bodies and are usually steeply dipping. They exhibit thermal zoning the mineralization changing from lead/zinc through copper to tin with depth. The tin zone virtually never exceeds 1,000' in depth and the ore shoots within this zone tend to be erratic and localized. The grade which is presently considered to be economic is about 0.7% Sn. , this means a concentration of about l% cassiterite (the only economic mineral) which, being twice as heavy as the gange, represents only. 5% of the lode volumetrically. Within the lode, only one third may reach this economic grade and values within the shoots can range from 100% cassiterite to zero over a few inches. The enormity of the problem of evaluating such a deposit has not been fully appreciated by the companies involved whose experience has, for the main part, been in larger and more predictable ore bodies. This paper attempts to put these problems into perspective and out- lines the useful applicatations of statistical and computer techniques. It also stresses the need for enlightened interpretation of data by men familiar with the problem and that even in this day and age, educated, intuitive deduction should not yet be relegated to the limbo of alchemy and witchcraft.

Jan 1, 1969

By Herman Poole

WHEN finely divided ferrous sulphide, FeS, is roasted at a moderate, carefully regulated temperature, the iron and sulphur are oxidized, the first products being probably ferrous oxide and sulphurous acid. In the presence of oxygen of the air the ferrous oxide soon becomes ferric oxide and in the presence of oxygen and the ferric oxide the sulphurous acid oxidizes to sulphuric acid. These facts are well known, having been established by Plattner many years ago. As a further reaction, some of the sulphuric acid parts with a portion of its oxygen to oxidize more ferrous oxide to ferric oxide, and a portion of it escapes uncombined or else unites with the iron oxides to form sulphates. Ferrous sulphate is usually soon oxidized to ferric sulphate and if the heat becomes sufficient this is then decomposed into sulphuric acid and ferric oxide. As a result of these reactions a mass of more or less pure ferric oxide is formed which is generally made porous by the escaping gases and, if rabbled properly, practically all the sulphur is expelled. If ferric sulphide or ordinary pyrites, FeS2, is roasted, a portion of the sulphur sublimes and usually burns to form sulphurous or sulphuric acid, although at times and under favorable conditions some of the sulphur is driven off uncombined and can be collected as such. Under ordinary methods of roasting, however, only a small portion escapes combustion. By the combustion of the sulphur an increase of heat is de¬veloped and, as a consequence, the reactions mentioned take place more rapidly and actively-more sulphuric acid is formed and the oxidation is more complete-nearly all the iron being left as ferric oxide with practically no sulphate or ferrous oxide. When the iron sulphide is in lumps the roasting proceeds generally as with fines, but with some changes due to mass. The

Sep 1, 1905

By J. L. Tokich, A. R. Troiano

Since 1921, when Hull1 discovered that cobalt can exist in the face-centered cubic and hexagonal close-packed modifications, the transitions that occur in cobalt have been extensively studied. It is generally agreed that on heating the hexagonal lattice changes to the cubic structure at ternperatures ranging from 400° to 500°C although considerable doubt exists as to the exact temperature. Data concerning the temperature of the transformation on cooling are much less concordant and their interpretation has not been satisfactory. The study is further complicated by the fact that many investigators have reported the existence of a high temperature allo-tropic change in the range 850 to 1020°C, at which the cubic lattice reverts to the hexagonal modification. The transition on cooling, which has been reported as Occurring at various temperatures from approximately 400 to 100°C, is of particular interest. Troiano and Greninger2 have recently suggested and considered the possibility Of allotropic transformations occurring in pure metals by a shear-type, diffusionless (martensite) transformation. The case of cobalt was specifically discussed and certain observations of previous investigators evaluated in terms Of this type of Of Table 1 briefly outlines the methods and results Of previous investigators Of the transformation temperatures of cobalt. Materials and Methods The major portion of this investigatioll was performed with cobalt sheet containing a total of 0.2 pet impurities with carbon present to the extent of o,I pct. After melting in an induction furnace under an atmosphere of hydrogen, the carbon con. tent analyzed 0.03 pct. Some observations were repeated with hydrogen reduced cobalt compresses analyzing 99.9 pet pure. No significant variations in results were observed employing the as-received sheet, the remelted stock, or the cobalt compresses. Filings for X ray diffraction analysis were sealed in evacuated glass ampoules. Pyrex glass tubing was used for temperatures below (600°C and for higher temperatures clear fused quartz was satisfactory. After appropriate heat treatment at various ternperatures, the specimen ampoules were furnace cooled, air cooled or quenched by crushing under distilled water. This allowed a range of cooling velocities from less than one degree C per set to greater than 1,0oo°C per sec. X ray diffraction patterns were taken with a Debye camera and filtered characteristic cobalt K-alpha radiation. The of of the existing phases was roughly approximated by visual examina-

Jan 1, 1949