Search Documents

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By Charles Austin

IN an earlier series of studies on 18-8 stainless steel at 600°, 700°, and 800°C.1 one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manu-factured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in, dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0,07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recom-mended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 750°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8 -in. dia., air cooling followed the annealing treatment. These treatments per-mitted two direct comparisons: (1) between the 1150° and 950°C. treat-ments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950° and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By Chu-Phay Yap

This is the first of a series of theoretical papers on the iron-carbon system. A simple critical analysis of the ordinary constitution diagram of the iron-carbon system yields valuable information regarding the nature of the equilibria in the liquid and solid states. It is shown, for example, that the solute in the melt is Fe3C, but in solid Fe (austenite) the solute is carbon. The thermodynamic laws of the depression in the freezing point of solid solutions have been developed and discussed. Using the usual method of plotting the logarithm value of the concentration of the solvent (in this case, the ratio of concentrations of the solvent in the liquid and solid phases) against 1/T, curves are obtained. A rigorous thermodynamic analysis of these curves has been shown to yield considerable information regarding the internal equilibria of the system, with which the phase rule does not deal altogether. In this way, it is shown again that the solute in the melt is Fe3C, but in the solid rFe the solute is carbon. Various heats of reaction (fusion and transition) and other thermal data have been derived: and discussed with a view to correlating the conflicting experimental data obtained by different investigators of the system.

Jan 1, 1931

By Richard Divine

IN the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and, some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. To do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the. top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000°C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seen-is to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues.

Jan 8, 1914

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By T. D. Lynch, N. B. Pilling

The development of a proper treatment for shells in conncction with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of the liquid itself upon both. Without attempting an exhaustive citation of the literature, mention may be made of some of the more important contributions, notably the pioneer work of Le Chatelier,' followed by the extensive investigations

Jan 1, 1920

By I. Javandel, P. A. Witherspoon

The finite element method was originally developed in the aircraft industry to handle problems of stress distribution in complex airframe configurations. This paper describes how the method can be extended to problems of transient flow in porous media. In this approach, the continuum is replaced by a system of finite elements. By employing the variational principle, one can obtain time dependent solutions for the potential at every point in the system by minimizing a potential energy functional. The theory of the method is reviewed. To demonstrate its validity, nonsteady-state results obtained by the finite clement method are compared with those of typical boundary value problems for which rigorous analytical solutions are available. To demonstrate the power of this approach, solutions for the more complex problem of transient flow in layered systems with crossflow are also presented. The generality of this approach with respect to arbitrary boundary conditions and changes in rock properties provides a new method of handling problems of fluid flow in complex systems. INTRODUCTION Problems of transient flow in porous media often can be handled by the methods of analytical mathematics as long as the geometry or properties of the flow system do not become too complex. When the analytical approach becomes intractable, it is customary to resort to numerical methods, and a great variety of problems have been handled in this manner. One such method relies on the finite difference approach wherein the system is divided into a network of elements, and a finite difference equation for the flow into and out of each element is developed. The solution of the resulting set of equations usually requires a high speed computer. When heterogeneous systems of arbitrary geometry must be considered, however, this approach is sometimes difficult to apply and may require large amounts of computer time. The finite element method is a new approach that avoids these difficulties. It was developed originally in the aircraft industry to provide a refined solution for stress distributions in extremely complex airframe configurations. 27 Clough has recently reviewed the application of the finite element method in the field of structural mechanics.6 The technique has been applied successfully in the stress analysis of many complex structures.l, 27, 28 Recognition that this procedure can be interpreted in terms of variational procedures involving minimizing a potential energy functional7 leads naturally to its extension to other boundary value problems. In the field of heat flow, there recently have been introduced several approximate methods of solution that are based on variational principles.2-4, 17 By employing the variational principle in conjunction with the finite element idealization, a powerful solution technique is now available for determining the potential distribution within complex bodies of arbitrary geometry. In the finite element approximation of solids, the continuum is replaced by a system of elements. An approximate solution for the potential field within each element is assumed, and flux equilibrium equations are developed at a discrete number of points within the network of finite elements. For the case of steady-state heat flow, the technique is completely described by Zienkiewicz and Cheung.33 Since the flow of fluids in porous media is analogous to the flow of heat, Zienkiewicz et al. have employed the finite element method in obtaining steady-state solutions to heterogeneous and anisotropic seepage problems. 34 Taylor and Brown have used this method to investigate steady-state flow problems involving a free surface.25 The work of Gurtin has been instrumental in laying the groundwork for the application of finite element methods to linear initial-value problems.12 As a result, Wilson and Nickell have recently

Jan 1, 1969

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By August Wendel

It is a well-known fact to all Bessemer steel manufacturers using a blooming mill, that ingots show large cracks in the first few passes of the rolls, which, in the following ones, do not always roll up satisfactorily. This deficiency in the quality of the product is generally called "red-shortness," though, in the writer's opinion, mostly unjustly so. Different explanations for the said peculiarity are given by the leading authorities, each works selecting one element as a special scapegoat for the inferior quality of the ingot. The sulphur is generally first charged as being the principal cause of all mischief in this direction ; then, after ascertaining that sulphur is not higher than the average, and sometimes lower in the very worst heats, silicon has to bear its share of abuse. How and why silicon should affect the working qualities of the metal, the writer could never precisely learn, but is convinced that the doctrine of its pernicious influence is an established one with many. In cases where silicon failed to explain everything, resort was taken to calcium, aluminum, and some other known or unknown elements, without settling the difficulty; and lastly, when the skill of the chemist became exhausted, " practical men " came to the same conclusion, which many leading blast-furnace managers had arrived

By Fred T. Greene

(San Francisco Meeting, September, 1915) MOST of. the recent discussion of the mineral land law published in the Transactions is in the abstract-an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversy,1 which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has. called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the least of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the " Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40° W., clipping about 40° to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80° W. and clips at high angles to the north and south.

Jan 5, 1915

By J. W. Stewart

That our American civilization will have extensive postwar problems in such fields as economics, unemployment, and social adjustment is now well understood by all readers of the press and listeners to the radio. But precious little is heard from these sources regarding the impact of the war on education, though education is one of the fields where the effect of the war is going to be felt most-for youth is fighting the war. Unquestionably, serious educational problems will ;rise in the postwar period, challenging the best efforts of our educators. Most acute will be the problems at the college level of education, for it is this age group that will have had its educational process most thoroughly disrupted. The return of these students to our college and university campuses wiI1 bring about a new set of conditions which we might as well try to foresee and begin to prepare for now. To begin with, the average returning college student who has had his education interrupted by war service will certainly be more mature in both years and mental outlook, and possibly married. As a result he will want to finish his college education as quickly as possible. His natural action will be to shop around among the various schools of the country to see where he can get the most credit for work he has done or thinks he has done. It is just possible that what might impolitely be termed "dark - market" schools may arise to cater to his needs. These schools will not think of them- selves in this light, of course, but will be conscious only of a keen sympathy for the veteran student and an urgent desire to help him solve his pressing problems. A considerable number of American colleges are going to be pretty well impoverished before this present war is ended and unless some professional organization takes it upon itself to place this possible situation under supervision and regulation, we may well suffer a serious setback to the

Jan 1, 1944

By John Hays Hammond

The Transvaal comprises about 120,000 square miles (nearly • the size of the United States Territory of New Mexico). Besides the famous Witwatersrand, which will here be de scribed in detail, there are two quartz-mining districts of some importance, viz., Lydenburg and De Kaap. The Lydenburg district first attracted attention in 1876, when the alluvial deposits of that section began to be exploited. At a later period vein-rnining was started, and at the present time several companies are operating in that district. The product in 1898 of five companies, running 137 stamps, was 154,560 tons of ore, yielding 108,884 crude ounces of gold (an average of 14.09 dwt. crude gold per ton) valued at £392,378. The De Eaap gold-fields were discovered in 1884. In 1898, seven companies, running 200 stamps, produced 89,760 crude ounces of gold, valued at £314,792. I. Mining Titles in the Transvaal. The mining laws of the Tranuvaal are most excellent in char acter, and while the claims cover every square foot of land for an area of nearly 40 miles long by from 2 to 3- miles wide, there have been practically no conflicts over extra-lateral rights. Notwithstanding the change in the political status of the Transvaal likely to follow the present war, it may be coufi dently assumed that the main features of the mining law of the South African Republic will be retained, and certain op pressive featureu of monopolies, etc., bearing with special weight on the mining industry, will be abolished. The dynamite mo nopoly was one that bore most heavily on the mining industry; and, according to the Reports of the State Mining Engineer, explosives, including fuse and detonators, amounted to nearly 10 per cent. of the total working costs of the mines. Further more, it was impossible to obtain the proper quality for the most economical working, and often 80-per-cent. or 40-per-cent. gelatine had to be used- in many instances where 60-per-cent.

Jan 1, 1902

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By M. B. Bever, A. K. Jena

Equations for the heat effects of additions of mixtures of multicomponent phases to a solution have been derived in terms of the enthalpy interaction coefficients. By these equations and the measured composition dependence of the heat effects on addition of mixtures of Ag-Cd solid solutions and elemental gold to liquid tin-rich solutions, values of the enthalpy in-teraction coefficients in tin-rich solutions at 541°K have been obtained. Analysis of these results in terms of the regular solution theory and the quasichemical theory suggests that near the melting point of the solvent association in the solution becomes important. SEVERAL recent papers have discussed the nature of dilute solutions on the basis of measured enthalpy interaction coefficients. l-3 These coefficients contribute to the understanding of the constitution of solutions and can be used for the evaluation of thermo-dynamic data of multicomponent systems. Their experimental determination, however, is laborious. This communication reports values of the enthalpy interaction coefficients of silver, cadmium, and gold in liquid tin-rich solutions obtained from the measured heat effects of additions of mixtures of Ag-Cd solid solutions and elemental gold to liquid tin-rich solutions. These measurements were made in the course of the determination of the heats of formation of Ag-Cd solid solutions reported in a concurrent publication.4 THE HEAT EFFECT OF AN ADDITION TO A SOLVENT This analysis is concerned with the addition of a mixture of multicomponent phases from the temperature To to a solvent of known composition at temperature T. If Nmixture << Nsolvent, where N designates the gram-atoms involved, the heat effect per g-atom of mixture added can be expressed as (HT - HT )i = difference in heat contents of component element i in the mixture at T and To Q = heat effect on solution of the mixture at temperature T Also1 Q = S Xi [2] where ?Hi ,T,x = relative partial enthalpy per g-atom of i in solution at temperature T and composition of the solution x x = average of the atom fractions of the added material in solution before and after the addition The relative partial enthalpy ?Hi per g-atom of an element i in a dilute solution composed of a solvent 1 and the solutes j = 2, ... m is related to the interaction coefficients by the following equation5 ?Hi - ?Hi-?Hi,x1-1 + S n1ixj+ . . . +S...S...S nrixn2... Xnji...Xnmm+... [3] vhere Xj = atom fraction of solute j in the solution nri = the rth order enthalpy interaction coefficients, which can also be represented by the more general designation5 L(i)n2,n3...nm and nj may have any positive integral value or zero. For identification of various rth order interaction coefficients, nri is written as nn2i2,...nij,...nmm. Eqs. [1], [2], and [3] combine to give the following general equation for the heat effect on addition of a small quantity of a mixture to a large quantity of a dilute solution n = _?ga ?Ha,To + ? Xi(HT - HT o)i a. i + ?xi?Hi,X,i?1 + ??xnjixj + . . . + ???. . .?. . .?xinrix2n2. . . xnji. . . xnmm+ . . . [4] The first term on the right-hand side of this equation is the heat of decomposition at the addition temperature of the phases present in the mixture, the second term is the heat required to raise the temperature of

Jan 1, 1970

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Jan. 10, 1916 to Feb. 10, 1916: William Rettie, Yonkers, N. Y. Wallace E. Pratt, Manila, P. I. R. V. Norris, Wilkesbarre, Pa. T. Skewes Saunders, El Oro, Mex. Fred MacCoy, El Oro, Mex. M. L. Requa, San Francisco, Cal. Reno H. Sales, Butte, Mont. R. W. Schultz, Ravenna, O. R. T. White, Batourn, Russia. H. J. Brown, Chester, Pa. David T. Day, Washington, D: C. A. M. Van Rensselaer, New Rochelle, N. Y. H. M. LaFollette, LaFollette, Tenn. Norman C. Stines, Russia. F. N. Speller, Pittsburgh, Pa. Howard R. Hughes, Houston, Tex. Robert W. Hunt, Chicago, Ill. C. F. Schnepp, Ridgefield Park, N. J. B. E. Fernow, Toronto, Ont., Can. George L. A. Thomson, Elizabeth, N. J. A. F. Bennett, New York City. Jasper T. Robertson, Chicago, Ill. J. C. Ralston, Spokane, Wash. J. B. Tyrrell, Toronto, Ont., Can. George J. Lyon, Schenectady, N. Y. H. G. Officer, New York Cty. Jesse C. Porter is now superintendent of the San Fernando Mine, Hoyo de Manicaragua, Santa Clara Province, Cuba.

Jan 3, 1916

By Francois E. Heuze

The Crestmore Mine of the American Cement Company lies at the eastern end of the Jurupa Mountains, 50 miles east of Los Angeles. Originally, a quarry was opened in 1908 for "limestone" used in the manufacture of cement. The mining operations eventually went underground employing first a modified system of block caving and later the "room and pillar" scheme. The limestones are relatively small roof pendants preserved in an enveloping and intrusive quartz diorite. They occur as two irregular lenticular bodies roughly parallel at the top and tending towards convergence at depth. Their dip varies between 25 and 30 degrees E. The presently mined lower bed, Chino limestone, is typically composed of alternating bands a few inches to a few feet thick of medium to coarsely granular white crystalline limestone and somewhat yellowish limestone (brucite marble). A "room and pillar" scheme of mining is currently employed in the lower body of the Crestmore Mine. The levels are horizontal and access is provided by a spiraling road starting in the old quarry. The present depth of operations is an average 750 ft below the surface. Fig. 1 gives a three-dimensional general sketch of the mine. The long axis of the rooms is in an E-W direction, normal to the strike of the beds. Fig. 2 is a horizontal map of the 130 level, the deepest level mined presently. It is in this level that most of the in-situ investigations have been conducted. The present investigation was made possible by a non-restrictive grant of the American Cement Company to the University of California. The program included a series of in-situ tests using flat-jacks, plate bearing,

Jan 1, 1968

By Martin A. Mayers

Five-sixths of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the production of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equipment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our comparative ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combustion rates. From this analysis it is possible to determine the characteristics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be considered first, because the independence of the individual particles facilitates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers, (8)† but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the temperature high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely. Furnaces Burning Pulverized Coal In a pulverized-coal furnace, the fuel particle is carried, in a stream of air, into the furnace, where it is subjected to radiation from the flame and from the hot walls of the furnace. The increase of particle tempera-

Jan 1, 1936