Search Documents

By W. J. Taylor

Some eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur mere naturally in the limekiln line, with solid fuel mixed with the ore, in the same way = common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known Pact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature..• This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseoua fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced— 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By S. W. Hazen

The use of operations research and computer techniques continued to expand during 1967. A number of mining companies either obtained computers or were experimenting with their use through service bureaus. This trend was also evident in the Canadian mining industry. Although the annual Symposium and Short Course on Computers and Operations Research in Mineral Industries was not held in 1967, technical periodicals like MINING ENGINEERING, Mining Congress Journal and Engineering and Mining Journal stepped up their coverage on the subject. The annual AIME meeting had eight papers in two sessions and one session on Operations Research was held at the SME Fall Meeting in Las Vegas.

Jan 2, 1968

By Leonard D. Jaffe

IN recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentially, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutectoid carbide. In the practical heat-treatment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper 1) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper 1: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. MATERIALS AND PROCEDURE It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, because the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1947

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By W. T. Isbell, Carleton C. Long

Zinc recovery from lead blast-furnace slags has heretofore been an indirect process, involving, first, the fuming off and collecting of an impure zinc oxide, and second, the reduction of the zinc portion of this oxide to metal either by electrolytic or pyrolytic means. (In a variation of this process, blue powder is the intermediate product rather than zinc oxide fume.) In 1940, W. T. Isbell proposed that molten slag from the lead blast furnace or stock-pile slag melted down in a blast or cupola-type furnace be charged directly into an airtight container (i.e., furnace) provided with means to heat further the slag by passage of electric current and means to introduce the carbon (coke) necessary to reduce the ZnO constituent of the slag to zinc as a zinc vapor and CO. He also proposed that the zinc vapors so obtained be condensed in a Weaton-Najariant internal condenser directly connected to the proposed furnace. It was thought that the Weaton-Najarian condenser could liquefy zinc vapor from lean mixtures of vapor and noncondensable gases. Such condensers have been in commercial use! since 1936 at Josephtown smelter, where the source of zinc vapor is a column of coke and zinc-bearing sinter electrically heated (charge resistor). Condenser output when supplied with vapor-gas mixtures containing approximately 45 per cent zinc and 55 per cent noncondensable gases, varies from 18 to 30 tons of slab zinc per day per condenser, depending upon the heat-transfer area (length) of the condenser and the volume of vapor (furnace size) fed to it. Lead-smelting operations at the St. Joseph Lead Company's plant at Hercu-laneum, Mo., produce a slag containing 12 to 16 per cent zinc. For several years this slag has been stock-piled with the object of recovering the zinc values if and when a commercial method was invented. Evaluation of the possibilities of the proposed method was made by pilot-plant operation at Josephtown. The first plant, designed in 1940 and operated in early 1941, consisted of a single-phase, two-electrode furnace. The evolved vapors were burned. Electrical characteiistics of the molten slag, power requirements, coke requirements, and extent of zinc elimination indicated the feasibility of the proposed method. In the latter part of 1941 a second pilot furnace was constructed, to which "was attached a small (6 ft. long) Weaton-Najarian condenser in order to develop an over-all picture of zinc-in-slag to zinc-in-slabs. This furnace was operated in the early part of 1942 and yielded such promising results that a decision was made to design- and construct a commercial furnace. Feed for the pilot-plant furnaces was granulated slag. A suitable deduction (300 to 350 kw-hr. per ton slag) was calculated in estimating power require-

Jan 1, 1944

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By P. R. Sperry, A. P. Beck

It has been shown1 that in poly-crystalline strips of high purity aluminum with a fairly random orientation distribution, grain growth progresses gradually until the average grain diameter reaches a value approximately equal to the strip thickness. Recent work at this laboratory led to the realization that grain growth might be impeded to a considerable extent in the presence of a sharply defined texture, where orientation differences between neighboring grains are small. In order to investigate this effect the following experiment was carried out with the same lot of high purity aluminum previously used for grain growth studies in randomly oriented material.' Very large grain size was developed by grain growth at 650°C in specimens of 0.200 in. thickness. These specimens were then rolled to a thickness of 0.050 in. or 1.25 mm—a reduction of 75 pct. In the rolled strip each large grain corresponded to an elongated area easily identified by etching. After annealing for 1 to 25 min at 600°C and re-etching, these elongated areas were again recognizable. Within each area, corresponding to a single large grain before annealing, there formed by recrystallization a multitude of new grains with a fairly well developed preferred orientation. The orientation and the size of the new grains formed in areas corresponding to different large grains, varied widely depending on the orientation of the parent grains with respect to the rolling direction and the plane of rolling. Many areas were found where the average grain size was considerably smaller than the specimen thickness. Such an area occurred in a specimen cut in half before annealing. One half, containing a portion of the area in question, was annealed 1 min at 600°C, the other half, with the remaining portion of this area, for 25 min at the same tempera-Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

W. H. BASSETT,* Waterbury, Conn. (written discussion ?).-The effect of reducing gases on hot solid copper has been known for many years in the copper industry, and precautions taken to guard against it in the general practice in copper heating and annealing. In view of the statement that Bengough and Hill, in 1910, were the first to suggest the possibility of the formation of gas within the copper itself, it is interesting to note that in Harper's Magazine for April, 1904, an article, "Life and Diseases of Metals," by Professor Heyn, illustrated the effect of reducing gases on copper by a photograph, which is shown in Fig. 1. This he entitled "Copper burst asunder by disease." After referring to the effect of hydrogen on steel, he makes the following remark: "Similar symptoms of poisoning, caused by hydrogen or gases containing hydrogen (as gas for lighting purposes), are apparent in copper when exposed to red heat. Not every kind of .copper is susceptible to this poisoning in equal degree. Copper per-fectly free of cuprous oxide is entirely exempt from poisoning. Most of the various coppers of commerce, however, contain cuprous oxide, formed during the smelting process while exposed to atmospheric influences. In such coppers, containing cuprous oxide, hydrogen causes a terrible disease on the copper being heated red hot. The copper bursts asunder and is permeated by cracks. This disease is practically incurable and can be eradicated by resmelting only. The results work destructively according to the amount of cuprous oxide contained in the copper." It must have been evident to Professor Heyn, as it was to us on reading this article, that the bursting asunder of the copper was clue to the formation of steam. Practical copper heaters have known for many years that it was quite possible to produce blisters, or large gas holes, in the interior of copper plates or bars by heating to a high temperature in reducing gases. These facts, of course, do not detract from the value of the study of the action of hydrogen gas that has been made by Mr. Pilling, but simply illustrate that the practical effect of reducing gases on furnace-refined copper has long been a troublesome factor in the heating or annealing of that metal.

Jan 1, 1919

By W. V. Swarzenski

In its effort to combat waterlogging and soil salinity, the Water and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling andwater sampling since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline groundwater zones in the Punjab Plain. Fresh groundwater containing generally less than 500 ppm of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh groundwater extends to depths of 1500 ft and more. Saline groundwater occurs down gradient from sources of recharge, particularly in the lower central parts of the interfluvial areas, and presumably underlies most of the Punjab Plain. The groundwaters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters near sources of recharge to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in the Dera Ismail Khan District, sodium sulfate waters predominate. The pattern of distribution of saline groundwater zones and the observed gradual increase in mineral content, down gradient from sources of recharge, can be explained best by a hypothesis stressing the process of evaporation from the water table and solution of minerals within the alluvial aquifer. In 1954, detailed groundwater surveys in the Punjab Plain were initiated by WASID, the Water and Soils Investigation Division of West Pakistan's Water and Power Development Authority. The investigations, undertaken under a cooperative agreement between the governments of Pakistan and the United States, were aimed at the formulation of reclamation measures to improve waterlogged and saline soils, and to assess the groundwater potential of the Punjab and other areas of West Pakistan. The nature and urgency of WASID's primary task limited the exploration of the alluvial aquifer generally to its uppermost part. About 1030 test holes drilled in 47,000 sq miles of the Punjab defined the nature of the alluvium to depths of about 600 ft and yielded data on water quality to 400 or 500 ft. A report on the hydrology of the Punjab, based on the results of these investigations was published by WASID in 1963.' The present report incorporates data obtained by WASID since 1962 in a program of deep test drilling in the Punjab and the adjacent areas of Bahawalpur and Dera Ismail Khan District, permitting the definition of fresh and saline groundwater zones to depths of 1500 ft in some areas. Groundwater in the Punjab Plain is contained in alluvial deposits, predominantly sand and silt, which extend almost everywhere to depths of 1000 ft and more. The alluvium has been deposited by the Indus River and its tributaries since late Tertiary time and is contiguous with similar deposits in India. The Indo-Gangetic Plain extends from the foothills of the Himalayas to the ancient rocks of the Peninsular Shield in central India and to the ocean. Gradients are generally very low and range from about 1% ft per mile in the upper part of the plain to less than 1 ft per mile in the south and southwest. The monotony of the alluvial plain is broken by scattered bedrock outcrops in two of the interfluvial areas, Chaj Doab and Rechna Doab. The bedrock hills are projections of the northwest-trending Delhi-Shahpur Ridge that is largely buried by alluvium. The rocks of the buried ridge, presumably of Precambrian age, are essentially impermeable and define the lower limit of the alluvial aquifer in parts of Chaj, Rechna, and Bari doabs. Elsewhere in the Punjab, there are no outcrops of other consolidated rocks and their presence below the alluvium is conjectural. The principal areas of bedrock outcrops, near Kirana and Sangla, are shown diagrammatically in Fig. 1. The movement of groundwater through the alluvial aquifer of the Punjab has been described by Green-man and others.' In most of the area, the pre-irriga-tion water table sloped from the rivers downstream and toward the central axes of the doabs, indicating that the rivers were sources of groundwater recharge. As a result of seepage from irrigation canals, water levels have risen as much as 90 ft. In 1960 they were within 5 to 15 ft of the land surface and above the

Jan 1, 1970

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By Jouko O. Kallioinen

The control of zinc flotation at Outokumpu Oy's Pyhasalmi and Vihanti mines is described. At Pyhäsalmi the zinc flotation circuit is partially open. Zinc and other metal assays of pulp flows are measured and direct assay control of concentrates in various flotation steps is adopted. Assay control is carried out by adjusting flotation air and pulp levels. Optimization with copper sulphate ensures high Zn- recovery and minimum copper sulphate consumption. A froth depth monitor is used to measure froth quality. At Vihanti the zinc flotation takes place in closed circuit. The most important control loop is the Zn-assay control of rougher concentrate by adjusting flotation air. The quality of froth is measured indirectly and thus copper sulphate consumption is altered. The circulating load is controlled also by flotation air in the three cleaning steps. The comparison of the control strategies shows that a more sophisticated control is adopted at Pyhäsalmi because the selective flotation of this massive sulphide ore is considered to be difficult. The control strategy includes numerous tests performed by the computer and control algorithms developed for the case. The control targets of the two zinc flotations described are also different: At Pyhäsalmi Zn-assay control of final concentrate including copper sulphate optimizing, at Vihanti the control of circulating load and Zn-assay of rougher concentrate.

Jan 1, 1984

By CHARLES M. A. STINE

THE value of chemical research has been so thor¬oughly demonstrated in the last few decades that the general public has become "research-conscious" to an extent which allows the advertising agent and publicity man to make use of research as a selling point in his advertising campaigns. We thus see the advertisements of concerns in the most varied industries stressing the research which is back of their products. The reason for this "research-consciousness" of the general public. is primarily that the products of research have increasingly engaged public attention and have. revolutionized our daily life. When we. reverse the flight of .time and imagine ourselves-in the century previous to our own, we find that we are .without the automobile, the radio, the improved telephone and electric light, refrigerated transportation, the airplane, X-rays, and many other things now taken for granted. A generation ago we find gloomy prophets foretelling the certain over-population .of the world within a few decades and an insufficiency of food due to lack of the fixed nitrogen which is now so plentifully ours.

Jan 1, 1930

By Jack M. Jodrey, Neil D. Donnell, O&apos

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1985

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By P. J. Conroy, E. A. Curth

INTRODUCTION In June 1962, the first attempt at longwall mining in Illinois was initiated by Old Ben Coal Company in their No. 21 Mine. Longwalling was continued intermittently using various supports until April 1970. During this period, longwall mining techniques were used on separate occasions at six faces within Mine No. 21. However, due to various problems that developed at each location the faces were eventually terminated. The most significant problems concerned the support systems and roof conditions that were present in the mine during each attempt. Between 1965 and 1972, similar conditions were met by Freeman Coal mining Company during four attempts at longwall mining in their Orient No. 5 and Orient No. 6 mines. In 1975, the U.S. Bureau of Mines and Old Ben Coal Company entered into a cost-sharing agreement to demonstrate the application of longwall mining in Illinois. The first phase of the demonstration was to conduct a premining investigation to review previous attempts at longwall mining, perform rock mechanics tests, and establish support requirements based on the lnvestigation results. The information obtained during the demonstration at Old Ben's No. 24 has been utilized to optimize subsequent face equipment and panel geometry. Mining of the first panel began in September 1976 and was successfully completed in May 1977, and two additional panels were mined under the cooperative agreement. Currently, Old Ben Coal Company is the only longwall mining operator in Illinois. In addition to the face in Mine No. 24, five longwall faces are being operated in four other mines.

Jan 1, 1981

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling' rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y' depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, ''' the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y' phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,'' but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By C. W. Washburne

Continued discussion of the paper Of ROSWELL H. JOHNSON, presented at the New York meeting, February, 1015, and printed in Bulletin No. 98, February; 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162, and No. 103, July, 1915, pp. 1449 to 1450. C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Mr. Johnson recognizes that connate waters must be driven, outward toward the earth's surface. He considers the ascent due to the settling and packing of the underlying sediments and to the formation of gas within the rocks, supplemented by abyssal pressures. The origin of the methane in the sedimentary strata probably is not simple. There are three possible modes of origin: (1) as marsh gas formed near the surface and entrapped in the sediments; (2) from abyssal sources; (3) by the decomposition of organic matter buried in the sediments. The abyssal source is generally negligible, and in all cases doubtful. The third origin is the most important in the gas fields. A fourth mode of origin, by the dissociation of liquid hydrocarbons, frequently has been suggested, but it is improbable, because crude oils are exothermic. Therefore they have no tendency, to split or decompose at low temperatures, as do endothermic substances, such as coal, which is geologically by the loss of methane, water, and carbon dioxide. This cannot happen to a hydrocarbon until its temperature of dissociation (" cracking point") is reached, which is over 250'.C. for the most easily cracked hydrocarbons and over 400° C. for others. Engler says that the dissociation of fats and waxes into oils is an endothermic process, thereby unconsciously nullifying his own theory of the dissociation of these substances at low temperatures. However, recently I have found reason to think that heat is liberated by the disruption of the molecules of fats and waxes, as it is in the molecular decomposition of the substances of wood, coal, etc. If this tentative opinion is correct, and Engler wrong, then it seems that the Engler-Höfer hypothesis of the origin of oil becomes not only possible, but even probable.

Jan 9, 1915

By John L. Lamont, Walter Crafts

AN investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method.1 The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to he necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. TESTING PROCEDURE The investigation was conducted principally on steels made at the Union Carbide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to-be-appropriate for the composi¬tions of the steels were used., Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham,of the Union Carbide and Carbon Research Laboratories, Inc., and is. a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944